Sparky m 750 User manual

1 – 9

ANGLE GRINDER

Original instructions

20 – 29

MEULEUSE ANGULAIRE

Notice originale

66 – 75

УГЛОШЛИФОВАЛЬНАЯ МАШИНА

Оригинальная инструкция по эксплуатации

76 – 85

КУтОШЛіФУВАЛЬНА МАШИНА

Оригінальна інструкція з експлуатації

86 – 95

ЪГЛОШЛИФОВЪЧНА МАШИНА

Оригинална инструкция за използване

www.sparkygroup.com

10 – 19

WINKELSCHLEIFER

Originalbetriebsanleitung

57 – 65

SZLIFIERKA KĄTOWA

Instrukcją oryginalną

30 – 38

SMERIGLIATRICE ANGOLARE

Istruzioni originali

48 – 56

REBARBADORA ANGULAR

Instrução original para o uso

39 – 47

ESMERILADORA ANGULAR

Instrucciones de uso originales

15.06.2012

Manufacturer

SPARKY Power Tools GmbH

Leipziger Str. 20

10117 Berlin, GERMANY

Signature of authorized person

A. Ivanov

Technical director of SPARKY ELTOS AG

DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product fulls all the relevant provisions of the following directives and the harmonized

standards: 2006/42/ЕС, 2004/108/EC, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Technical le is stored at SPARKY ELTOS AG, Koubrat Str. 9, 5500 Lovetch, Bulgaria.

KONFORMITÄTSERKLÄRUNG

Hiermit versichern wir unsere persönliche Haftung, dass dieses Erzeugnis allen einschlägigen Bestimmungen folgender Richtlinien und

entsprechender harmonisierten Standards entspricht: 2006/42/ЕС, 2004/108/EC, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2,

EN 61000-3-2, EN 61000-3-3.

Die technischen Unterlagen werden bei SPARKY ELTOS AG, Kubrat Str.9, 5500 Lovetch, Bulgarien, aufbewahrt.

DECLARATION DE CONFORMITE

Nous déclarons sous notre responsabilité que ce produit satisfait à l’ensemble des dispositions pertinentes de la présente directives,

respectivement aux normes harmonisées: 2006/42/ЕС, 2004/108/EC, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2,

EN 61000-3-2, EN 61000-3-3.

Le dossier technique est conservé par SPARKY ELTOS AD, 9, rue Kubrat, Lovech, Bulgarie.

DICHIARAZIONE DI CONFORMITÀ

Noi dichiariamo sotto la nostra personale responsabilità, che questo prodotto è in conformità a tutte le disposizioni pertinenti della

presente direttive e norme armonizzate:2006/42/ЕС, 2004/108/EC, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 61000-3-2,

EN 61000-3-3.

Il fascicolo tecnico viene custodito presso la SPARKY ELTOS, 5500 Lovech, via Kubrat n. 9, Bulgaria

DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que este producto está conforme con todas las disposiciones aplicables de la

presente directrices aplicables y las correspondientes normas armonizadas: 2006/42/ЕС, 2004/108/EC, EN 60745-1, EN 60745-2-3,

EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

El expediente técnico está archivado en SPARKY ELTOS SA, C/ Kubrat, 9, 5500 Lovech, Bulgaria.

DECLARAÇÄO DE CONFORMIDADE

Declaramos assumindo a nossa responsabilidade pessoal que este produto está conforme com todas as disposições relevantes

da presente directrizes aplicáveis e respectivos estandartes harmonizados: 2006/42/ЕС, 2004/108/EC, EN 60745-1, EN 60745-2-3,

EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

O expediente técnico ca guardado na SPARKY ELTOS SA, rua Kubrat, 9, 5500 Lovech, Bulgária

DEKLARACjA ZGODNOśCI

Niniejszym deklarujemy naszą osobistą odpowiedzialnością, że ten produkt spełnia wszystkie odpowiednie postanowienia następujących

dyrektyw i harmonizowanych standardów: 2006/42/ЕС, 2004/108/EC, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2,

EN 61000-3-2, EN 61000-3-3.

Teczka techniczna przechowywana jest w SPARKY ELTOS AG, Kubrat Str.9, 5500 Lovetch, Bułgaria

ДЕКЛАРАЦИЯ О СООтВЕтСтВИИ

Мы заявляем со всей ответственностью, что данный продукт полностью соответствует всем соответствующим требованиям

действующих директив и гармонизированных стандартов: 2006/42/ЕС, 2004/108/EC, EN 60745-1, EN 60745-2-3, EN 55014-1,

EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Техническое досье хранится в СПАРКИ ЕЛТОС АД, ул. Кубрат №9, 5500 Ловеч, Болгария.

ДЕКЛАРАЦіЯ ПРО ВіДПОВіДНіСтЬ

Ми заявляємо під свою власну відповідальність, що даний продукт відповідає всім діючим вимогам директив і гармонізованих

стандартів: 2006/42/ЕС, 2004/108/EC, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Технічне досьє зберігається в СПАРКИ ЕЛТОС АД, ул. Кубрат № 9, 5500 Ловеч, Болгарія.

ДЕКЛАРАЦИЯ ЗА СЪОтВЕтСтВИЕ

Ние декларираме на своя лична отговорност, че това изделие отговаря на всички приложими изисквания на следните

директиви и хармонизирани стандарти: 2006/42/ЕС, 2004/108/EC, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2,

EN 61000-3-2, EN 61000-3-3.

Техническото досие се съхранява в СПАРКИ ЕЛТОС АД, ул. Кубрат №9, 5500 Ловеч, България.

720 W

600 W • 650 W

M 720

M 600 • M 650

1206R02

www.sparkygroup.com

Page is loading ...

1

M 600 • M 650 • M 720 • Original instructions

EN

Contents

I - Introduction .......................................................................................................................................................... 1

   ...................................................................................................................................... 3

III - General power tool safety warnings .................................................................................................................. 4

IV - Angle grinder safety warnings ............................................................................................................................ 5

V - Know your product ...........................................................................................................................................A/7

VI - Operation .............................................................................................................................................................. 7

VII - Maintenance ........................................................................................................................................................ 8

VIII - Warranty ............................................................................................................................................................... 9

UNPACKING





so could result in serious personal injury.

ASSEMBLY

The angle grinder is packed fully assembled except for the wheel guard and the auxiliary handle.

I - Introduction

Your new SPARKY power tool will more than satisfy your expectations. It has been manufactured under stringent



and, with proper care, it will give you many years of dependable service.

WARNING:

Carefully read through this entire Instruction Manual before using your new SPARKY power tool. Take special

care to heed the Warnings. Your SPARKY power tool has many features that will make your job faster and

easier. Safety, performance, and dependability have been given top priority in the development of this tool,

making it easy to maintain and operate.

Do not dispose of electrical products together with household waste!

Waste electrical products should not be disposed of with household waste. Please recycle where facilities

exist. Check with your local authority or retailer for recycling advice.

ENVIRONMENTAL PROTECTION

The machine, accessories and packaging should be sorted for environmental-friendly recycling.

The plastic components are labelled for categorised recycling.

2

M 600 • M 650 • M 720

EN

DESCRIPTION OF SYMBOLS

The rating plate on your power tool may show symbols. These represent important information about the

product or instructions on its use.

Always wear eye protection.

Double insulated for additional protection.

Spindle thread: M10

Spindle thread: M14

Conforms to the relevant European Directives

Conforms to the requirements of Russian standards

Conforms to the requirements of Ukrainian standards

Refer to original instructions

YYYY-Www

Production period, where the variable symbols are:

YYYY - year of manufacture, ww - calendar week number

M ANGLE GRINDER

3

Original instructions

EN

The vibration emission level given in this information sheet has been measured in accordance with a standardised test

given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of

exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool is used for dif-

-

cantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched



working period.

Maintain the power tool and the accessories and keep your hands warm during operation to reduce the harmful effect

of vibrations.

Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful. Contact

with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders.



for wood conditioning (chromate, wood preservative). Material containing asbestos must only be treated by specialists.

 Where the use of a dust extraction device is possible it shall be used.

 To achieve a high level of dust collection, use vacuum cleaner for wood or for wood and/or minerals together with

this tool.

 The work place must be well ventilated.

 The use of a dust mask of filter class P2 is recommended.



II - Technical specications

Model M 600 M 650 M 720

 Power input 600 W 650 W 720 W

 No load speed 11000 min

-1

11000 min

-1

11000 min

-1

 Spindle thread  M14 M14

 Spindle thread length 20 mm 20 mm 20 mm

 Wheel arbor 16 22,23 22,23

 Max. wheel diameter 100 mm 115 mm 125 mm

 Max. wheel thickness 6 mm 6 mm 6 mm

 Weight (EPTA Procedure 01/2003) 1,2 kg 1,2 kg 1,2 kg

 Safety class (EN 60745-1)

II II II

NOISE AND VIBRATION INFORMATION (Measured values determined according to EN 60745.)

 Noise emission

A-weighted sound pressure level L

pA

94.2 dB(A) 94.2 dB(A) 94.2 dB(A)



pA

3 dB 3 dB 3 dB

A-weighted sound power level L

wA

105.2 dB(A) 105.2 dB(A) 105.2 dB(A)



wA

3 dB 3 dB 3 dB

Wear hearing protection!

 Vibration emission *

Total vibration values (vector sum in the three axes) determined according to EN 60745:

 Surface grinding

Vibration emission value a

h,AG

4,2 m/s

2

4,3 m/s

2

4,5 m/s

2



AG

1,5 m/s

2

1,5 m/s

2

1,5 m/s

2

 Sanding

Vibration emission value a

h,DS

3,9 m/s

2

4,0 m/s

2

4,2 m/s

2



DS

1,5 m/s

2

1,5 m/s

2

1,5 m/s

2

* The vibration emission values are determined according to 6.2.7 EN 60745-1.

4

M 600 • M 650 • M 720

EN

III - General power tool

safety warnings

WARNING! Read all safety warnings and

all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or

serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

b) Do not operate power tools in explosive atmos-

pheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while op-

erating a power tool. Distractions can cause you

to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords in-

crease the risk of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your finger on the switch or energising power tools

that have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

e) Do not overreach. Keep proper footing and bal-

ance at all times. This enables better control of

the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, en-

sure these are connected and properly used.

Use of dust collection can reduce dust-related haz-

ards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off. Any power tool that can-

not be controlled with the switch is dangerous and

must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing ac-

cessories, or storing power tools. Such preven-

tive safety measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

5

Original instructions

EN

5) SERVICE

a) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

IV - Angle grinder safety

warnings

Safety Warnings Common for Grinding, Wire Brush-

ing or Abrasive Cutting-Off Operations:

         

grinder, sander, wire brush, polisher or cut-off

tool. Read all safety warnings, instructions, il-

lustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or

serious injury.

b) This power tool is not recommended for polish-

ing. Operations for which the power tool was not

designed may create a hazard and cause personal

injury.

c) Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

e) The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

f) The arbour size of wheels, flanges, backing

pads or any other accessory must properly

fit the spindle of the power tool. Accessories

with arbour holes that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

g) Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or acces-

sory is dropped, inspect for damage or install

an undamaged accessory. After inspecting

and installing an accessory, position yourself

and bystanders away from the plane of the

rotating accessory and run the power tool at

maximum no-load speed for one minute. Dam-

aged accessories will normally break apart during

this test time.

h) Wear personal protective equipment. Depend-

ing on application, use face shield, safety gog-

gles or safety glasses. As appropriate, wear

dust mask, hearing protectors, gloves and

workshop apron capable of stopping small

abrasive or workpiece fragments. The eye pro-

tection must be capable of stopping flying debris

generated by various operations. The dust mask

or respirator must be capable of filtrating particles

generated by your operation. Prolonged exposure

to high intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken accessory

may fly away and cause injury beyond immediate

area of operation.

j) Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring

or its own cord. Cutting accessory contacting a

“live” wire may make exposed metal parts of the

power tool “live” and could give the operator an

electric shock.

k) Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled into

the spinning accessory.

l) Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the power

tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the ac-

cessory into your body.

n) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal

may cause electrical hazards.

o) Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution or shock.

 

purpose. Any use other use than those men-

tioned in this Instruction will be considered a

case of misuse. The user and not the manufac-

turer shall be liable for any damage or injury result-

ing from such cases of misuse.

        

changes made to the tool nor for any damage

resulting from such changes.

 -

tilation slots must be kept clean. If it should be-

come necessary to clear dust, first disconnect

the tool from the mains supply (use non metal-

lic objects to clean the dust) and avoid damag-

ing internal parts. The power tool will overheat

under deteriorated cooling due to the clogged with

dust ventilation slots.

Further safety instructions for all operations

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other acces-

sory. Pinching or snagging causes rapid stalling of the

rotating accessory which in turn causes the uncontrolled

power tool to be forced in the direction opposite of the

accessory’s rotation at the point of the binding.

6

M 600 • M 650 • M 720

EN



by the workpiece, the edge of the wheel that is enter-

ing into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out. The

wheel may either jump toward or away from the operator,

depending on direction of the wheel’s movement at the

point of pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/or in-

correct operating procedures or conditions and can be

avoided by taking proper precautions as given below.

 -

tion your body and arm to allow you to resist

kickback forces. Always use auxiliary handle,

if provided, for maximum control over kick-

back or torque reaction during start-up. The

operator can control torque reactions or kickback

forces, if proper precautions are taken.

b) Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

c) Do not position your body in the area where

power tool will move if kickback occurs. Kick-

back will propel the tool in direction opposite to the

wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create fre-

quent kickback and loss of control.

 -

propriate way.



Cutting-Off Operations:

       

for your power tool and the specific guard de-

signed for the selected wheel. Wheels for which

the power tool was not designed cannot be ade-

quately guarded and are unsafe.

b) The guard must be securely attached to the

power tool and positioned for maximum safe-

ty, so the least amount of wheel is exposed to-

wards the operator. The guard helps to protect

the operator from broken wheel fragments, ac-

cidental contact with wheel and sparks that could

ignite clothing.

c) Wheels must be used only for recommended

applications. For example: do not grind with

the side of cut-off wheel. Abrasive cut-off wheels

are intended for peripheral grinding, side forces ap-

plied to these wheels may cause them to shatter.

d) Always use undamaged wheel flanges that

are of correct size and shape for your selected

wheel. Proper wheel flanges support the wheel

thus reducing the possibility of wheel break-

age. Flanges for cut-off wheels may be different

from grinding wheel flanges.

e) Do not use worn down wheels from larger

power tools. Wheel intended for larger power tool

is not suitable for the higher speed of a smaller tool

and may burst.

 -

rection. The torque reaction is in the opposite di-

rection of the rotation direction at the point of bind-

ing and this is a prerequisite to loosing control of

the power tool.

 

sparks and dust can scatter away from your

body. Power tools generate sparks which may

burn your clothes or unprotected parts of your

body.

 

painted metal structures is not allowed before

the paint has become dry. There is a risk of damp

paint ignition.

      -

tics, etc.) and panel structures “sandwich”

type with flammable filling is not allowed.

There is a risk of fire.

 -

ment operating under pressure is not allowed.

There is a risk of explosion.

   -

voirs, pipelines, equipment, etc., containing at

present or having contained flammable or eas-

ily ignitable substances or materials is not al-

lowed without first taking special precautions

to prevent fire and explosion. There is a risk of

fire and explosion.

     

Cutting-Off Operations:

         -

cessive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibility

of kickback or wheel breakage.

b) Do not position your body in line with and be-

hind the rotating wheel. When the wheel, at the

point of operation, is moving away from your body,

the possible kickback may propel the spinning

wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a

cut for any reason, switch off the power tool

and hold the power tool motionless until the

wheel comes to a complete stop. Never attempt

to remove the cut-off wheel from the cut while the

wheel is in motion otherwise kickback may occur.

Investigate and take corrective action to eliminate

the cause of wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted in

the workpiece.

e) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge of

the workpiece on both sides of the wheel.

f) Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The pro-

truding wheel may cut gas or water pipes, electrical

wiring or objects that can cause kickback.

7

Original instructions

EN

-

tions:

    

brush even during ordinary operation. Do not

overstress the wires by applying excessive

load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

or brush may expand in diameter due to work load

and centrifugal forces.

V - Know your product

Before using the power tool, familiarize yourself with all

the operating features and safety requirements.

Use the tool and accessories only for the applications

intended. All other applications are expressly ruled out.

1. Spindle

2.1. Wheel guard for grinding wheel

2.2. Wheel guard for cutting wheel *

  

4.1. Grinding wheel (Use only with a wheel guard for

grinding wheel!) *

4.2. Cutting wheel (Use only with a wheel guard for

cutting wheel!) *

  

6. Auxiliary handle

  

8. Spindle lock button

ACCESSORIES TO BE USED WITH THIS

POWER TOOL*

9. Wire cup brush

10. Abrasive wheels for cutting and grinding



12. Anti-vibration handle

* The basic SPARKY accessories used with this machine

are shown on pages 96-99. They are not included in the

delivery.

VI - Operation

These power tools are supplied from single-phase al-

ternating current mains only. They are double insulated

according to EN 50144, IEC 60745-1 and can be con-

nected to grounded or not grounded sockets. This power

tool is radio suppressed in compliance with EMC Direc-

tive 2004/108/EC.

This power tool is designed for cutting, grinding and

brushing mainly metals without using water.

PRIOR TO INITIAL OPERATION

 The machine may be delivered with the wheel guard

mounted at the factory. Ensure that the wheel guard is

mounted properly and fixed reliably prior to the initial

and any following operation.

 The machine may be delivered with the wheel mount-

ed at the factory. Ensure that the wheel is mounted

properly and fixed reliably prior to the initial and any

following operation.

 Make sure the power supply voltage corresponds to

the value indicated on the name plate with technical

data of the tool.

        

power tool must be connected to the power supply



plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

 Make sure that the cord and the plug are in order. If the

replacement of the supply cord is necessary, this has

to be done by the manufacturer or his agent in order

to avoid a safety hazard.

WARNING: Always switch off and unplug the

power tool prior to any adjustment, servicing or main-

tenance.

 Make sure the grinding wheel diameter and thickness

do not exceed the values specified on the name plate.

The peripheral speed indicated on the wheel must not

be less than 80 m/s. The wheels must be stored ac-

cording the recommendations of the manufacturer.

 In case the work area is remote from the power

source, use as short as practicable extension cord

with proper cross-section.

 Check that the auxiliary handle is properly mounted

and reliably tightened.

WHEEL GUARD

WARNING: The wheel guard (2.1) for grinding

wheels or the wheel guard (2.2) for cutting wheels (for

grinding wheels (4.1) or cutting wheels (4.2) accord-

ingly) must always be mounted on the machine!

Its position can be different and depends on which side

the auxiliary handle is placed, as well as when the ma-

chine is mounted on a stand.

MOUNTING THE WHEEL GUARD

Before performing the following operations switch the

machine off and withdraw the plug from the socket.

1. Mounting the wheel guard

- Open the fastening lever (15) and loosen screw (16)

if necessary. (Fig.1)

- Place the wheel guard so that the cotters (14) will

coincide with the grooves (17) and press the wheel

guard down to enter the groove (18) around the

bearing bed. (Fig.2a, b)

- Tighten the screw (16) to eliminate the clearance

between the guard bracket and the bearing bed

enough to ensure slight relative rotation between

them.

- Rotate the wheel guard to the desired position.

8

M 600 • M 650 • M 720

EN

 

- If necessary, repeat the operation for eliminating the

clearance between the guard bracket and the bear-

ing bed.

2. Rotating the wheel guard to a new operating po-

sition

- Open the fastening lever (15).

- Turn the wheel guard to the new operation position.

- Close the fastening lever (15).

MOUNTING THE WHEEL

Secure spindle (1) by depressing the spindle lock button

(8) provided on the gear case.

WARNING: Never press button (8) while the

spindle is still rotating!

 -

ward. (Fig.3)

 

with the inscriptions facing down. (Fig.4)

 

wheel (4) and fasten it by hand. Place the two-pin

        

(Fig.5)

- With the spindle lock button (8) depressed tighten

       

(Fig. 6a, b)

After replacing the wheel operate the machine with the

new wheel in no load mode for one minute. Vibrating or

otherwise improperly rotating wheels must be replaced

immediately and discarded.

Cup brushes (9) are screwed directly on spindle (1) by

means of an open-end spanner. (Check if the brush



AUXILIARY HANDLE

Normally the auxiliary handle is screwed on the machine

left side. It can be mounted also on the machine right

side if this is more convenient for the operator.

SWITCHING ON - SWITCHING OFF

Switching on:

(7) down and then forward in the direction of the arrow



Switching off: Press the back, lifted end of switch (7)

and release it to return in its initial position.

WARNING: At low temperature or if the power

tool has not been used for a long period, switch on and

let the power tool run for one minute at no load in order

to establish normal operation mode, thus achieving

improved lubrication and prolonged life of the power

tool.

RECOMMENDATIONS

When cutting, do not apply pressure, do not oscillate the

wheel. Work with moderate feed rate, suited to the mate-

rial to be machined.



must always be fed against the direction of wheel rota-

tion. Otherwise, danger exists for the wheel to be forced

uncontrolled out of the cut. (Fig.7)

         

start with the smallest cross section.

When grinding do not apply pressure to the processed

surface by rearing down on the machine but move

the wheel regularly backwards and forwards. Special

wheels shall be used for processing non-ferrous met-

als. Best results when roughing can be achieved with the

wheel inclined at 30° to 40° to the processed surface.

Never use cutting wheels for roughing operations. Us-

age of wheels thicker than 6 mm is not recommended.

VII - Maintenance

WARNING: Always ensure that the tool is

switched off and unplugged before attempting to per-

form inspection or maintenance.

BRUSH REPLACEMENT

This power tool is equipped with auto-stop brushes.

When the carbon brushes are worn out, the machine

switches itself off. In this case both brushes must be re-

placed simultaneously with genuine brushes at SPARKY

service centre for warranty and post-warranty service.

GENERAL INSPECTION

Regularly inspect all fasteners and ensure they are prop-

erly tightened. Should any of the screws be loose, retight-

en it immediately to avoid hazards.

If the replacement of the supply cord is necessary, this

has to be done by the manufacturer or his agent in order

to avoid a safety hazard.

CLEANING

-

tilation slots clean.

Regularly check to see if any dust or foreign matter has

entered the ventilation slots and the grills around the

switches. Use a soft brush and/or air jet to remove any

accumulated dust. Wear safety glasses to protect your

eyes whilst cleaning.

Exterior plastic parts may be cleaned with a damp cloth

and mild detergent if necessary.

WARNING: Never use alcohol, petrol or other

cleaning agent. Never use caustic agents to clean

plastic parts.

WARNING: Water must never come into con-

tact with the tool.

9

Original instructions

EN

IMPORTANT! To assure product safety and reliability,

repairs, maintenance and adjustment (including brush

inspection and replacement) should be performed by

       -

ganisations, always using genuine replacement parts.

VIII - Warranty

The guarantee period for SPARKY power tools is deter-

mined in the guarantee card.

-

dling will be excluded from the guarantee.



defects in workmanship will be corrected free of charge

through replacement or repair.

The complaints for defective SPARKY power tools will

be recognized if the machine is sent back to the dealer

or is presented to the authorised warranty service centre

undismantled, in its initial condition.

Notes

Carefully read the entire original instructions before us-

ing this product.

The manufacturer reserves the right to make changes

-

tions without prior notice.



Page is loading ...

98

Cat. N D x d, mm P

ALUMINIUM OXIDE - Straight

ALUMINIUMOXID - Gerade

OXYDE D’ALUMINIUM - Plane

OSSIDO DI ALLUMINIO - Diritta

OXIDO DE ALUMINIO - Recto

ÓXIDO DE ALUMÍNIO – Com lamellas rectas

TLENEK ALUMINIUM - Prosta







20009578300 100 x 16 40

20009578500 100 x 16 60

20009578700 100 x 16 80

20009578900 100 x 16 120

20009571900 115 x 22.23 40

20009572000 115 x 22.23 60

20009572100 115 x 22.23 80

20009572200 115 x 22.23 120

20009572300 125 x 22.23 40

20009572400 125 x 22.23 60

20009572500 125 x 22.23 80

20009572600 125 x 22.23 120

ALUMINIUM OXIDE - Inclined

ALUMINIUMOXID - Gewinkelt

OXYDE D’ALUMINIUM - Angulaire

OSSIDO DI ALLUMINIO - bombata



ÓXIDO DE ALUMÍNIO – Com lamellas inclinadas









20009578400 100 x 16 40

20009578600 100 x 16 60

20009578800 100 x 16 80

20009579000 100 x 16 120

20009573500 115 x 22.23 40

20009573600 115 x 22.23 60

20009573700 115 x 22.23 80

20009573800 115 x 22.23 120

20009573800 125 x 22.23 40

20009574000 125 x 22.23 60

20009574100 125 x 22.23 80

20009574200 125 x 22.23 120

ZIRCONIUM OXIDE - Straight

ZIRKONKORUND - Gerade

OXYDE DE ZIRCONIUM - Plane

CORINDONE ZIRCONIO - Diritta



ÓXIDO DE CIRCÓNIO – Com lamellas rectas

TLENEK CYRKONU - Prosta







20009579100 100 x 16 40

20009579300 100 x 16 60

20009579500 100 x 16 80

20009579700 100 x 16 120

20009575100 115 x 22.23 40

20009575200 115 x 22.23 60

20009575300 115 x 22.23 80

20009575400 115 x 22.23 120

20009575500 125 x 22.23 40

20009575600 125 x 22.23 60

20009575700 125 x 22.23 80

20009575800 125 x 22.23 120

11

A

B

Page is loading ...

Sparky m 750 User manual

This manual is also suitable for

Sparky m 750 User manual

in other languages

Related papers

Other documents