Whirlpool GGW9250SU0 User guide

Brand: Whirlpool

Model: GGW9250SU0

Category: Tumble dryers

Type: User guide

This manual is also suitable for

GGW9250S

ELECTRONIC

GAS DRYER

Use & Care Guide

In the U.S.A., for questions about features, operation/

performance, parts, accessories or service call:

1-800-253-1301

In Canada, for assistance, installation and service call:

1-800-807-6777

or visit our website at... www.whirlpool.com or

www.whirlpool.ca

SÉCHEUSE À GAZ

ELECTRONIQUE

Guide d’utilisation et d’entretien

Pour assistance, installation ou service composez

1-800-807-6777

ou visitez notre site web à

www.whirlpool.ca

Table of Contents/Table des matières......................... 2

W10049550

TABLE OF CONTENTS

DRYER SAFETY..............................................................................3

INSTALLATION INSTRUCTIONS..................................................5

Tools and Parts ............................................................................5

Options.........................................................................................5

Location Requirements ...............................................................6

Electrical Requirements ...............................................................8

Gas Supply Requirements...........................................................8

Venting Requirements..................................................................9

Plan Vent System.......................................................................10

Install Vent System.....................................................................12

Install Leveling Legs...................................................................12

Level Dryer .................................................................................12

Make Gas Connection ...............................................................12

Connect Vent..............................................................................13

Complete Installation .................................................................13

DRYER USE ..................................................................................14

Starting Your Dryer.....................................................................14

Stopping Your Dryer ..................................................................15

Pausing or Restarting.................................................................15

Control Locked...........................................................................15

Drying and Cycle Tips................................................................15

Status Lights ..............................................................................16

Cycles.........................................................................................16

Additional Features ....................................................................17

Drying Rack................................................................................18

DRYER CARE ..............................................................................19

Cleaning the Dryer Location ......................................................19

Cleaning the Lint Screen............................................................19

Cleaning the Dryer Interior .........................................................19

Removing Accumulated Lint......................................................19

Vacation and Moving Care.........................................................20

Changing the Drum Light...........................................................20

TROUBLESHOOTING ..................................................................20

ASSISTANCE OR SERVICE.........................................................22

WARRANTY ..................................................................................23

TABLE DES MATIÈRES

SÉCURITÉ DE LA SÉCHEUSE ....................................................24

INSTRUCTIONS D’INSTALLATION.............................................26

Outillage et pièces......................................................................26

Options .......................................................................................26

Exigences d’emplacement.........................................................27

Spécifications électriques ..........................................................29

Alimentation en gaz....................................................................30

Exigences concernant l'évacuation ...........................................31

Planification du système d’évacuation ......................................32

Installation du système d’évacuation.........................................34

Installation des pieds de nivellement.........................................34

Mise à niveau de la sécheuse....................................................35

Raccordement au gaz................................................................35

Raccordement du conduit d’évacuation ...................................35

Achever l’installation ..................................................................36

UTILISATION DE LA SÉCHEUSE................................................37

Mise en marche de la sécheuse ................................................37

Arrêt de la sécheuse...................................................................38

Mise en pause ou remise en marche.........................................38

Verrouillage des commandes.....................................................38

Conseils pour le séchage et les programmes ...........................38

Témoins lumineux ......................................................................39

Programmes...............................................................................40

Caractéristiques supplémentaires .............................................41

Grille de séchage........................................................................41

ENTRETIEN DE LA SÉCHEUSE.................................................42

Nettoyage de l'emplacement de la sécheuse ...........................42

Nettoyage du filtre à charpie......................................................42

Nettoyage de l’intérieur de la sécheuse.....................................43

Retrait de la charpie accumulée ................................................43

Précautions à prendre pour les vacances et avant un

déménagement ..........................................................................43

Changement de l’ampoule d’éclairage du tambour..................43

DÉPANNAGE.................................................................................44

ASSISTANCE OU SERVICE.........................................................46

GARANTIE.....................................................................................47

DRYER SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

– WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

•

If you cannot reach your gas supplier, call the fire department.

– Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

•

Clear the room, building, or area of all occupants.

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

■ If using a ball valve, it shall be a T-handle type.

■ A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

WARNING:

■

Read all instructions before using the dryer.

■

Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

■

Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

■

Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

■

Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

■

Do not reach into the dryer if the drum is moving.

■

Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

■

Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

■

Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

■

Clean lint screen before or after each load.

■

Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

SAVE THESE INSTRUCTIONS

■

The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

■

Do not install or store the dryer where it will be exposed

to the weather.

■

Do not tamper with controls.

■

See installation instructions for grounding requirements.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

INSTALLATION INSTRUCTIONS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Parts supplied

Remove parts packages from dryer drum. Check that all parts are

included.

■ Parts package

4 Leveling legs

NOTE: Do not use leveling legs if installing the dryer on a

pedestal.

Parts needed

Check local codes and with gas supplier. Check existing gas

supply, electrical supply and venting. Read “Electrical

Requirements,” “Gas Supply Requirements” and “Venting

Requirements” before purchasing parts.

■ For close-clearance installations between 31.5" (80.01 cm)

and 37" (93.98 cm), see “Plan Vent System” section for

venting requirements.

Mobile home installations require special parts (listed following)

that may be ordered by calling the dealer from whom you

purchased your dryer. For further information, please refer to the

“Assistance or Service” section of this manual.

■ Mobile Home Installation Kit. Ask for Part Number 346764.

■ Metal exhaust system hardware.

Options

Pedestal

Are you placing the dryer on a pedestal? You have the option of

purchasing pedestals of different heights separately for this dryer.

You may select a 10" (25.4 cm), a 13" (33 cm) or a 15.5" (39.4 cm)

pedestal. These pedestals will add to the total height of the dryer

for a total height of approximately 48" (121.9 cm), 51" (129.5 cm)

or 53.5" (135.9 cm), respectively.

For a garage installation, you will need to place the 10" (25.4 cm)

pedestal at least 9" (22.9 cm) above the floor and the 13" (33 cm)

pedestal at least 6" (15.2 cm) above the floor. You will need to

place the 15.5" (39.4 cm) pedestal at least 3.5" (8.9 cm) above

the floor.

Optional pedestal

The pedestals are available in several colors.

To order, call the dealer from whom you purchased your dryer or

refer to the “Assistance or Service” section of this manual.

Stack Kit

Are you planning to stack your DUET

washer and dryer? To do

so, you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or

refer to the “Assistance or Service” section of this manual. Ask

for Part Number 8541503.

■ 8" or 10" pipe wrench

■ 8" or 10" adjustable

wrench (for gas

connections)

■ Flat-blade screwdriver

■ Adjustable wrench that

opens to 1" (2.5 cm) or

hex-head socket wrench

(for adjusting dryer feet)

■ ¹⁄₄" nut driver or socket

wrench

■ Level

■ Knife

■ Vent clamps

■ Pipe-joint compound

resistant to LP gas

■ Caulking gun and

compound (for installing

new exhaust vent)

■ Pliers

■ Tape measure

37"

(93.98 cm)

Pedestal

Height

Color Part Number

10" (25.4 cm) White WHP1000SQ

10" (25.4 cm) Biscuit WHP1000ST

10" (25.4 cm) Pewter WHP1000SL

10" (25.4 cm) Diamond Dust

(Silver)

WHP1000SU

13" (33 cm) White LAB2700MQ

13" (33 cm) Biscuit LAB2700MT

13" (33 cm) Pewter LAB2700ML

15.5" (39.4 cm) White WHP1500SQ

15.5" (39.4 cm) Biscuit WHP1500ST

15.5" (39.4 cm) Pewter WHP1500SL

15.5" (39.4 cm) Diamond Dust

(Silver)

WHP1500SU

Door Reversal Kit

Are you planning to reverse the door swing direction on your

DUET

dryer? To do so, you will need to purchase a Door

Reversal Kit.

To order, call the dealer from whom you purchased your dryer or

refer to the “Assistance or Service” section of this manual. Ask

for Part Number 8530069 (Shield Blue), 8530070 (Shield

Platinum), 8530071 (Biscuit), 8530072 (Pewter) or 8579123

(Diamond Dust [Silver]).

Door Reversal and Stack Combination Kit

Are you planning to reverse the door swing direction on your

DUET

dryer and stack your DUET

washer and dryer? To do so,

you can purchase a Door Reversal and Stack Combination Kit.

To order, call the dealer from whom you purchased your dryer or

refer to the “Assistance or Service” section of this manual. Ask

for Part Number 8530073 (Shield Blue), 8530074 (Shield

Platinum), 8530075 (Biscuit), 8530076 (Pewter) or W10057200

(Diamond Dust [Silver]).

Backguard

If you are installing your DUET

washer and dryer and wish to

avoid having loose items fall behind your machines, you may

purchase a pair of washer/dryer backguards. These will reduce

the chance of items falling behind the machines during operation.

To order, call the dealer from whom you purchased your dryer or

refer to the “Assistance or Service” section of this manual. Ask

for Part Number 8558694 (White), 8558695 (Biscuit), 8558696

(Pewter), or W10057220 (Diamond Dust [Silver]).

Location Requirements

You will need

■ A location that allows for proper exhaust installation. A gas

dryer must be exhausted to the outdoors. See “Venting

Requirements.”

■ A grounded electrical outlet located within 2 ft (61 cm) of

either side of the dryer. See “Electrical Requirements.”

■ A sturdy floor to support the total dryer weight of 200 lbs

(90.7 kg). The combined weight of a companion appliance

should also be considered.

■ A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer. If slope is greater than 1" (2.5 cm), install Extended

Dryer Feet Kit, Part Number 279810. Clothes may not tumble

properly, and automatic sensor cycles may not operate

correctly if dryer is not level.

■ For a garage installation, you will need to place the dryer at

least 18" (46 cm) above the floor. If you are using a 10"

(25.4 cm) pedestal, you will need to place the pedestal at

least 9" (22.9 cm) above the floor. With a 13" (33 cm)

pedestal, you will need to place the pedestal at least

6" (15.2 cm) above the floor. With a 15.5" (39.4 cm) pedestal,

you will need to place the pedestal at least 3.5" (8.9 cm)

above the floor.

Do not operate your dryer at temperatures below 45ºF (7ºC). At

lower temperatures, the dryer might not shut off at the end of an

automatic cycle. This can result in longer drying times.

The dryer must not be installed or stored in an area where it will

be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes or

sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the

same closet as a dryer.

Installation clearances

The location must be large enough to allow the dryer door to

open fully.

Dryer Dimensions

*Most installations require a minimum 5" (12.7 cm) clearance

behind the dryer for the exhaust vent with elbow. See “Venting

Requirements.”

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this

dryer. This dryer has been tested for spacing of 0" (0 cm)

clearance on the sides and rear. Recommended spacing should

be considered for the following reasons:

■ Additional spacing should be considered for ease of

installation and servicing.

■ Additional clearances might be required for wall, door and

floor moldings.

■ Additional spacing should be considered on all sides of the

dryer to reduce noise transfer.

■ For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

■ Companion appliance spacing should also be considered.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

38"

(96.52 cm

)

*31½"

(80 cm)

27"

(68.6 cm)

51½"

(130.81 cm)

Custom undercounter installation - Dryer only

*Required spacing

Closet installation - Dryer only

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Recessed or closet installation - Dryer on pedestal

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Installation spacing for cabinet installation

■ For cabinet installation, with a door, minimum ventilation

openings in the top of the cabinet are required.

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Recommended installation spacing for recessed or

closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

*Required spacing

A. Side view - closet or confined area

B. Closet door with vents

A. Recessed area

B. Side view - closet or confined area

(0 cm)

1"*

(2.5 cm)

1"*

(2.5 cm)

38" min.

(96.52 cm)

27"

(68.6 cm)

14" max.*

(35.6 cm)

18" min.*

(45.72 cm)

1"*

5"**

(12.7 cm)

31½"

(80 cm)

48 in.

(310 cm

)

24 in.

(155 cm

)

3"*

(7.6 cm)

3"*

(7.6 cm)

(2.5 cm)

1"*

(2.5 cm)

5"**

(12.7 cm)

27"

(68.6 cm)

31½"

(80 cm)

18" min.*

(45.72 cm)

14" max.*

(35.6 cm)

7"* (17.8 cm)

9"*

(22.9 cm

)

7"* (17.8 cm)

5"**

(12.7 cm)

31¹₂"

(80.0 cm)

27"

(68.6 cm)

1"*

(2.5 cm)

1" 1"

(2.5 cm)

48 in.

(310 cm

)

3"* (7.6 cm)

1"* (2.5 cm)

24 in.

(155 cm

)

6"* (15.2 cm)

76"

(193 cm)

27"

(68.6 cm)

5"*

(12.7 cm)

(2.5 cm)

Mobile home - Additional installation requirements

This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240

MH.

Mobile home installations require:

■ Metal exhaust system hardware, which is available for

purchase from your dealer.

■ Mobile Home Installation Kit Part Number 346764. See “Tools

and Parts” section for ordering information.

■ Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a

nearby window) should be at least twice as large as the dryer

exhaust opening.

Electrical Requirements

■ 120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is also recommended that a separate circuit

serving only this dryer be provided.

Gas Supply Requirements

Gas Type

Natural gas:

This dryer is equipped for use with Natural gas. It is design-

certified by CSA International for LP (propane or butane) gases

with appropriate conversion.

■ Your dryer must have the correct burner for the type of gas in

your home. Burner information is located on the rating plate

in the door well of your dryer. If this information does not

agree with the type of gas available, contact your dealer or

call the phone numbers referenced in the “Assistance or

Service” section of this manual.

LP gas conversion:

Conversion must be made by a qualified technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting your gas company.

Gas supply line

■ Must include ¹⁄₈" NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas

connection to the dryer (see illustration).

■ ¹⁄₂" IPS pipe is recommended.

■ ³⁄₈" approved aluminum or copper tubing is acceptable for

lengths under 20 ft (6.1 m) if local codes and gas supplier

permit.

■ If you are using Natural gas, do not use copper tubing.

■ Lengths over 20 ft (6.1 m) should use larger tubing and a

different size adapter fitting.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

■ If your dryer has been converted to use LP gas, ³⁄₈" LP

compatible copper tubing can be used. If the total length of

the supply line is more than 20 ft (6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of LP gas

must be used. Do not use TEFLON

®†

tape.

■ Must include a shutoff valve:

In the U.S.A.:

An individual manual shutoff valve must be installed within

six (6) feet (1.8 m) of the dryer in accordance with the National

Fuel Gas Code, ANSI Z223.1.

In Canada:

An individual manual shutoff valve must be installed in

accordance with the B149.1, Natural Gas and Propane

Installation Code. It is recommended that an individual

manual shutoff valve be installed within six (6) feet (1.8 m)

of the dryer.

The location should be easy to reach for opening and closing.

Gas supply connection requirements

■ Use an elbow and a ³⁄₈" flare x ³⁄₈" NPT adapter fitting

between the flexible gas connector and the dryer gas pipe, as

needed to avoid kinking.

■ Use only pipe-joint compound. Do not use TEFLON

®†

tape.

■ This dryer must be connected to the gas supply line with a

listed flexible gas connector that complies with the standard

for connectors for gas appliances, ANSI Z21.24 or CSA 6.10.

Burner input requirements

Elevations above 10,000 ft (3,048 m):

■ When installed above 10,000 ft (3,048 m) a 4% reduction of

the burner Btu rating shown on the model/serial number plate

is required for each 1,000 ft (305 m) increase in elevation.

Gas supply pressure testing

■ The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than

½ psi.

Dryer gas pipe

■ The gas pipe that comes out through the rear of your dryer

has a ³⁄₈" male pipe thread.

*NOTE: If the dryer is mounted on a pedestal, the gas pipe height

must be an additional 10" (25.4 cm), 13" (33 cm) or 15.5"

(39.4 cm) from the floor, depending on the pedestal model. For a

garage installation, the gas pipe height must be an additional

18" (46 cm) from the floor.

Venting Requirements

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

■ Clean lint from the entire length of the system and make sure

exhaust hood is not plugged with lint.

■ Replace any plastic or metal foil vent with rigid or flexible

heavy metal vent.

■ Review Vent system chart. Modify existing vent system if

necessary to achieve the best drying performance.

A. ³⁄₈" flexible gas connector

B. ³⁄₈" pipe to flare adapter fitting

C. ¹⁄₈"

NPT minimum plugged tapping

D. ½" NPT gas supply line

E. Gas shutoff valve

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

A. ½" NPT gas supply line

³⁄₈

" NPT dryer pipe

*6¼"

(15.9 cm)

1½"

(3.8 cm)

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

If this is a new vent system

Vent material

■ Use a heavy metal vent. Do not use plastic or metal foil vent.

■ 4" (10.2 cm) heavy metal exhaust vent and clamps must be

used. DURASAFE™ venting products are recommended.

DURASAFE™ vent products can be purchased from your

dealer or by calling Whirlpool Parts and Accessories. For

more information, see the “Assistance or Service” section of

this manual.

Rigid metal vent

■ For best drying performance, rigid metal vents are

recommended.

■ Rigid metal vent is recommended to avoid crushing and

kinking.

Flexible metal vent

■ Flexible metal vents are acceptable only if accessible for

cleaning.

■ Flexible metal vent must be fully extended and supported

when the dryer is in its final location.

■ Remove excess flexible metal vent to avoid sagging and

kinking that may result in reduced airflow and poor

performance.

■ Do not install flexible metal vent in enclosed walls, ceilings or

floors.

Elbows

45° elbows provide better airflow than 90° elbows.

Clamps

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

Exhaust

Recommended hood styles are shown here.

The angled hood style (shown here) is acceptable.

■ An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

■ Exhaust hood must be at least 12" (30.5 cm) from the ground

or any object that may be in the path of the exhaust (such as

flowers, rocks or bushes, snow line, etc.).

■ Do not use an exhaust hood with a magnetic latch.

Plan Vent System

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

4" (10.2 cm) heavy metal exhaust vent

Good Better

Clamp

10.2 cm

A. Louvered hood style

B. Box hood style

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

E. Clamps

F. Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

(10.2 cm)

2½"

(6.4 cm)

Improper venting can cause moisture and lint to collect

indoors, which may result in:

Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

Housecleaning problems and health problems.

Optional exhaust installations

This dryer can be converted to exhaust out the right side, left

side, or through the bottom.

Contact your local dealer to have the

dryer converted.

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for

your installation. Two close-clearance installations are shown.

Refer to the manufacturer’s instructions.

NOTE: The following kits for close clearance alternate

installations are available for purchase. Please see the

“Assistance or Service” section of this manual to order.

■ Over-the-Top Installation:

Part Number 4396028

■ Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm)

mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path

■ Select the route that will provide the straightest and most

direct path outdoors.

■ Plan the installation to use the fewest number of elbows and

turns.

■ When using elbows or making turns, allow as much room as

possible.

■ Bend vent gradually to avoid kinking.

■ Use the fewest 90° turns possible.

Determine vent length and elbows needed for best

drying performance

■ Use the following Vent system chart to determine type of vent

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in

the Vent system chart. Exhaust systems longer than those

specified will:

■ Shorten the life of the dryer.

■ Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will

help to achieve the best drying performance.

A. Standard rear offset exhaust installation

B. Left or right side exhaust installation

C. Bottom exhaust installation (not an option

with pedestal installations)

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation

WARNING

Fire Hazard

Cover unused exhaust holes with one of the

following kits:

279818 (white)

279925 (biscuit)

279969 (pewter)

280171 (diamond dust)

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90º turn

inside the dryer. To determine maximum exhaust length, add one

90º turn to the chart.

Install Vent System

1. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See “Determine vent path” in “Plan Vent System.” Avoid 90º

turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior

of the vent to secure vent.

Install Leveling Legs

1. To protect the floor, use a large flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge

of the dryer.

2. Firmly grasp the body of the dryer. Gently lay the dryer on the

cardboard. See illustration.

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to the floor at the time of

installation.

Mobile home installations require a Mobile Home Installation Kit.

For more information, please reference the service numbers in

the “Assistance or Service” section of this manual.

Level Dryer

Check the levelness of the dryer. Check levelness first

side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block.

Use a wrench to adjust the legs up or down and check again for

levelness.

Make Gas Connection

1. Remove the red cap from the gas pipe.

2. Using a wrench to tighten, connect the gas supply to the

dryer. Use pipe-joint compound on the threads of all non-

flared male fittings. If flexible metal tubing is used, be sure

there are no kinks.

NOTE: For LP gas connections, you must use pipe-joint

compound resistant to the action of LP gas. Do not use

TEFLON

®†

tape.

Number of

90º turns

or elbows

Type of

vent

Box or

louvered

hoods

Angled

hoods

0 Rigid metal

Flexible metal

64 ft (20 m)

36 ft (11 m)

58 ft (17.7 m)

28 ft (8.5 m)

1 Rigid metal

Flexible metal

54 ft (16.5 m)

31 ft (9.4 m)

48 ft (14.6 m)

23 ft (7 m)

2 Rigid metal

Flexible metal

44 ft (13.4 m)

27 ft (8.2 m)

38 ft (11.6 m)

19 ft (5.8 m)

3 Rigid metal

Flexible metal

35 ft (10.7 m)

25 ft (7.6 m)

29 ft (8.8 m)

17 ft (5.2 m)

4 Rigid metal

Flexible metal

27 ft (8.2 m)

23 ft (7 m)

21 ft (6.4 m)

15 ft (4.6 m)

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

A. Flared male fitting

B. Non-flared male fitting

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

A combination of pipe fittings must be used to connect the

dryer to the existing gas line. Shown is a recommended

connection. Your connection may be different, according to

the supply line type, size and location.

3. Open the shutoff valve in the supply line. The valve is open

when the handle is parallel to the gas pipe.

4. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

Connect Vent

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Make sure the vent is secured

to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible

gas line.

4. Once the exhaust vent connection is made, remove the

corner posts and cardboard.

Complete Installation

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer’s final location. Be sure the vent is not

crushed or kinked.

5. Check that the dryer is level. See “Level Dryer.”

6. Plug into a grounded 3 prong outlet. Turn on power.

7. Remove any protective film or tape remaining on the dryer.

8. Read “Dryer Use.”

9. Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

10. Select a Timed Dry heated cycle, and start the dryer. Do not

select the Air Only Temperature setting.

If the dryer will not start, check the following:

■ Dryer is plugged into a grounded 3 prong outlet.

■ Electrical supply is connected.

■ Household fuse is intact and tight, or circuit breaker has

not tripped.

■ Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the

dryer door and feel for heat. If you feel heat, cancel cycle and

close door. If you do not feel heat, turn off the dryer and

check that the gas supply line shutoff valve is open.

■ If the gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

■ If the gas supply line shutoff valve is open, contact a

qualified technician.

³⁄₈

" flexible gas connector

³⁄₈

" dryer pipe

³⁄₈

" to

³⁄₈

" pipe elbow

³⁄₈

" pipe-to-flare adapter fitting

A. Closed valve

B. Open valve

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

DRYER USE

Starting Your Dryer

The following is a guide to starting your dryer. Please refer to

specific sections of this manual for more detailed information.

1. Clean lint screen before each load. See “Cleaning the Lint

Screen.”

2. Place laundry into dryer and shut door.

3. Rotate the dial to select either an Automatic or Manual Cycle

then press the CONTROL ON button. The preset settings and

drying time for the cycle chosen will be displayed.

To use an Automatic Cycle

■ Point the dial to an Automatic Cycle.

■ Select DRYNESS LEVEL to adjust how dry you want the

load to be. The time displayed is an estimated length of

the cycle based on the Dryness Level selected. As the

cycle runs, the control senses the dryness of the load and

adjusts the time automatically for the selected Dryness

Level.

NOTE: Time is not adjustable for Automatic Cycles. Pressing

the More Time or Less Time buttons will cause a triple beep,

indicating that the time cannot be changed.

■ Press the WRINKLE SHIELD™ feature button if this

option is desired.

■ Press the END OF CYCLE SIGNAL button to set signal

volume to desired level.

■ Press (and hold) HOLD TO START button until dryer starts

(about 1 second).

Once an Automatic cycle has started, the WRINKLE

SHIELD™ feature and cycle signals can be adjusted. Press

the PAUSE/CANCEL key twice to stop the dryer and clear the

settings, allowing you to select another cycle and Dryness

Level.

Less

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

WARNING

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

Items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

How Automatic Cycles Work

EvenHeat™ improves drying performance with Auto Moisture

Sensing Plus, which advances the cycle as moisture is

extracted from clothing. A thermistor (electronic temperature

sensor) and moisture sensing strips in the dryer drum help

measure the amount of moisture in the clothes as they pass.

An electronic control determines the load type to help save

time, avoid overdrying, and increase the accuracy of the end

dryness level. After the first 5 minutes of an automatic cycle,

the estimated time display will adjust based on the

approximate load size, cycle, dryness level selected and

amount of moisture left in the clothes. When the clothes have

reached approximately 80% of the dryness level selected, the

estimated time display will adjust again, showing the final

drying time. Auto Moisture Sensing Plus takes the guesswork

out of drying time and enhances fabric care.

To use a Manual Cycle

■ Rotate the dial to select a Manual Cycle.

Press MORE TIME or LESS TIME until the desired drying time

is displayed. Tap MORE TIME or LESS TIME, and the time will

change by 1-minute intervals. Press and hold MORE TIME or

LESS TIME, and the time will change by 5-minute intervals.

The initial time displayed is the actual drying time.

NOTE: The More Time or Less Time feature can be used only

with Manual Cycles.

■ Press TEMPERATURE until the desired temperature

glows.

NOTE: Pressing the Dryness Level button will cause the triple

beep indicating that this option is not selectable. Also, a

Dryness Level is not indicated.

■ Press the WRINKLE SHIELD™ feature button if this

option is desired.

■ Press the END OF CYCLE SIGNAL button to set volume

to desired level.

■ Press (and hold) HOLD TO START button until dryer starts

(about 1 second).

While a Manual Cycle is running, you can change the settings

for Time, Temperature, the WRINKLE SHIELD™ feature and

the cycle signals. Press the PAUSE/CANCEL key twice to

stop the dryer and clear the settings, allowing you to select

another cycle.

Stopping Your Dryer

To stop your dryer at any time

Press PAUSE/CANCEL twice or open the door.

Pausing or Restarting

To pause the dryer at any time

Open the door or press PAUSE/CANCEL once.

To restart the dryer

Close the door and press (and hold) HOLD TO START button until

dryer starts.

NOTE: Drying will continue from where the cycle was interrupted,

if you close the door and press Start within 5 minutes. If the cycle

is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

Control Locked

This feature allows you to lock your settings to avert unintended

use of the dryer. You can also use the Control Locked feature to

avert unintended cycle or option changes during dryer operation.

To enable the Control Locked feature when dryer is

running:

Press and hold the END OF CYCLE SIGNAL button for

3 seconds. The control is locked when a single beep is heard and

the Control Locked status light is on.

■ When the dryer is off, it is not necessary to press the Control

On button before activating the Control Locked feature.

To unlock:

Press and hold the END OF CYCLE SIGNAL button for 3 seconds

to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the

dryer can be stopped by pressing the Pause/Cancel button, but

can’t be restarted until the control is unlocked.

Drying and Cycle Tips

Select the correct cycle and dryness level or temperature for your

load. If an Automatic Cycle is running, the display shows the

estimated cycle time when your dryer is automatically sensing

the dryness level of your load. If a Manual Cycle is running, the

display shows the exact number of minutes remaining in the

cycle.

Cool Down tumbles the load without heat during the last few

minutes of all cycles. Cool Down makes the loads easier to

handle and reduces wrinkling. The length of the Cool Down

depends on the load size and dryness level.

Drying tips

■ Follow care label directions when they are available.

■ If desired, add a fabric softener sheet. Follow package

instructions.

■ Remove the load from the dryer as soon as tumbling stops to

reduce wrinkling. This is especially important for permanent

press, knits, and synthetic fabrics.

■ Avoid drying heavy work clothes with lighter fabrics. This

could cause overdrying of lighter fabrics, leading to increased

shrinking or wrinkling.

■ If you dry sheets in a mixed load or large items in the Bulky

Items cycle, rearrange the load when the signal sounds. This

will aid in the drying process.

Cycle tips

■ Dry most loads using the preset cycle settings.

■ Refer to the Automatic or Manual Preset Cycle Settings chart

(in the “Cycles” section) for a guide to drying various loads.

■ Drying temperature and Dryness Level are preset when

you choose an Automatic Cycle. You can choose a

different dryness level, depending on your load by

pressing the DRYNESS LEVEL button to select MORE or

LESS.

■ If you wish to adjust the cycle length of a Manual Cycle,

you must press MORE TIME or LESS TIME. Adjust the

temperature of a Manual Cycle by pressing

TEMPERATURE until the desired temperature is selected.

NOTE: You cannot choose a Dryness Level with Manual

Cycles.

Status Lights

You may follow the progress of your dryer with the drying Status

indicator lights.

Sensing

When a cycle is first turned on, the Sensing light glows until a wet

item is detected.

■ In an Automatic Cycle, if a wet item has not been detected

within 10 minutes, the Sensing light will turn off and the dryer

will shut down.

■ In a Manual Cycle, if a wet item is not detected after

10 minutes the Wet light turns on and the selected cycle

continues.

Wet

The Wet light will turn on when a wet item has been detected in

the dryer. The Wet light will remain on until:

■ The damp dry point is reached in an Automatic Cycle.

■ The dryer enters the cool down period in a Manual Cycle.

Damp

The Damp light indicates that the load has reached the damp dry

level.

NOTE: The Damp light is not used with manual cycles.

Cool Down

The Cool Down light glows during the cool down part of the

cycle. Laundry is cooling down for ease in handling.

Cycle Complete

This light glows when a drying cycle is finished. If the WRINKLE

SHIELD™ feature has been selected, the WRINKLE SHIELD™

feature indicator light will also be on.

The Cycle Complete light turns off 1 hour after the end of a drying

cycle (including the WRINKLE SHIELD™ cycle of 2 hours), when

Pause/Cancel is pressed, or when the door is opened.

WRINKLE SHIELD™ Feature

The WRINKLE SHIELD™ feature light glows when this option is

selected. This indicator stays on with the Cycle Complete light.

Control Locked

The Control Locked light glows when this option is enabled.

Indicator lights

Other indicator lights on the control panel show Cycle,

Temperature, and End of Cycle settings selected.

The time display will indicate the estimated or actual time

remaining in a cycle.

Cycles

Select the drying cycle that matches the type of load you are

drying. See Automatic Preset or Manual Preset Cycle Settings

chart.

Cycle control knob

AUTOMATIC CYCLES

Automatic Cycles allow you to match the cycle to the load you

are drying. See the following Automatic Preset Cycle Settings

chart. Each cycle dries certain fabrics at the recommended

temperature. A sensor detects the moisture in the load and

automatically adjusts the drying time for optimal drying.

Heavy Duty

Use this cycle to get High heat for heavyweight mixed loads,

cotton towels or jeans.

Normal

Use this cycle to get Medium heat for drying sturdy fabrics such

as work clothes.

Bulky Items

Use this cycle to get Medium heat for drying large items that

require very long drying times such as jackets, comforters and

pillows. Rearrange the load halfway through the dryer cycle. This

will aid in the drying process.

Casual

Use this cycle to get Low heat for drying no-iron fabrics such as

sport shirts, casual business clothes and permanent press

blends.

Delicate

Use this cycle to get Extra Low heat to gently dry items such as

lingerie or washable knit fabrics.

Automatic Preset Cycle Settings

*Estimated Time with Dryness Level (medium) setting. Time will

vary depending on load type and load size.

Automatic Cycles

Load Type

Temperature Time*

(Minutes)

HEAVY DUTY

Heavyweight items, towels, jeans

High 40

NORMAL

Corduroys, work clothes

Medium 34

BULKY ITEMS

Jackets, comforters, pillows

Medium 64

CASUAL

Permanent press, synthetics

Low 36

DELICATE

Lingerie, blouses, washable

woolens

Extra Low 22

MANUAL CYCLES

Use Manual Cycles to select a specific amount of drying time and

a drying temperature. When a Manual Cycle is selected, the

Estimated Time Remaining display shows the actual time

remaining in your cycle. You can change the actual time in the

cycle by pressing MORE TIME or LESS TIME.

Timed Dry

Use this cycle to complete drying if items are still damp after an

Automatic Cycle. Timed Dry is also useful for drying heavyweight

and bulky items such as bedspreads and work clothes.

Lightweight garments, such as exercise wear, can be dried using

Timed Dry on a Low temperature setting.

Touch Up

Use this setting to help smooth out wrinkles from such items as

clothes packed in a suitcase or wrinkled from being left in the

dryer too long.

Quick Dry

Use this cycle for drying small loads or loads that need a short

drying time.

Manual Preset Cycle Settings

Additional Features

WRINKLE SHIELD™ Feature

When you are unable to remove a load of clothes from the dryer

as soon as it stops, wrinkles can form. The WRINKLE SHIELD™

feature periodically tumbles, rearranges and fluffs the load to help

keep wrinkles from forming.

■ Press the WRINKLE SHIELD™ feature to get up to

120 minutes of heat-free, periodic tumbling at the end of a

cycle.

■ Stop at any time by pressing the WRINKLE SHIELD™ feature

or opening the dryer door.

■ For the Casual Cycle, the WRINKLE SHIELD™ feature is

preset to “ON.” The other Automatic Cycles will retain the

WRINKLE SHIELD™ feature setting. (For example, if you

select the WRINKLE SHIELD™ feature in the Normal cycle,

the WRINKLE SHIELD™ feature will be on the next time you

select the Normal cycle.)

NOTE: If you do not select the WRINKLE SHIELD™ feature, the

dryer stops after the cool down period.

Temperature

Temperature settings are used with the Manual Cycles. Press

TEMPERATURE until the desired temperature setting glows.

Temperature settings cannot be used with the Automatic Cycles.

Air Only

Use the Air Only setting for items that require drying without heat

such as rubber, plastic and heat-sensitive fabrics. This chart

shows examples of items that can be dried using Air Only.

*Reset time to complete drying, if needed.

When using Air Only

■ Check to see that coverings are securely stitched.

■ Shake and fluff pillows by hand periodically during the cycle.

■ Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Automatic Cycles are not available when using the Air

Only setting.

End of Cycle Signal

The End of Cycle Signal produces an audible sound when the

drying cycle is finished. Promptly removing clothes at the end of

the cycle reduces wrinkling.

Press and release the END OF CYCLE SIGNAL to adjust the

sound level or turn off the signal.

NOTE: When the WRINKLE SHIELD™ feature is selected and the

End of Cycle Signal is on, an audible sound will be emitted every

5 minutes until the clothes are removed, or the WRINKLE

SHIELD™ feature is finished.

Manual Cycles

Load Type

Temperature Default Time

(Minutes)

TIMED DRY

Heavyweight items, bulky

items, bedspreads, work

clothes

High 40

TOUCH UP

Helps to smooth out

wrinkles

Medium 20

QUICK DRY

Small loads

High 23

Type of Load Time*

(Minutes)

Foam rubber - pillows, padded bras, stuffed toys 20 - 30

Plastic - Shower curtains, tablecloths 20 - 30

Rubber-backed rugs 40 - 50

Olefin, polypropylene, sheer nylon 10 - 20

Drying Rack

The drying rack is useful for drying items you would not

necessarily want to tumble dry or that you would normally line dry

(for example, sweaters).

To use the drying rack

Do not remove the lint screen.

1. Open dryer door.

2. Place drying rack inside dryer drum, positioning the back wire

on the ledge of the inner dryer back panel. Push down on

front edge of drying rack to secure over the lint screen.

3. Put the wet items on top of the rack. Leave space between

the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

4. Close the door.

5. Select a timed drying cycle and temperature, or an air cycle

(see following chart). Items containing foam, rubber, or plastic

must be dried on a clothesline or by using the Air Only

temperature setting.

6. You must select a time by pressing MORE TIME or LESS

TIME. Reset time as needed to complete drying. Refer to the

following table.

7. Press (and hold) HOLD TO START button (about 1 second).

NOTE: You must remove rack for normal tumbling. Do not use

automatic cycles with the drying rack.

This chart shows examples of items that can be rack dried and

the suggested cycle, temperature setting and drying time. Actual

drying time will depend on the amount of moisture items hold.

*(Minutes) Reset time to complete drying, if needed.

A. Front edge

A. Dryer rack front edge

B. Dryer back panel

Rack Dry Setting Temp. Time*

Wool Sweaters

Block to shape and lay flat on

the rack.

Timed

Dry

Low 60

Stuffed toys or pillows

Cotton or polyester fiber filled

Timed

Dry

Low 60

Stuffed toys or pillows

Foam rubber filled

N/A Air Only

(no heat)

Sneakers or canvas shoes N/A Air Only

(no heat)

DRYER CARE

Cleaning the Dryer Location

Keep dryer area clear and free from items that would obstruct the

flow of combustion and ventilation air.

Cleaning the Lint Screen

Every load cleaning

The lint screen is located in the door opening of the dryer. The

control panel has an indicator light to remind you to clean the lint

screen before or after each load. A screen blocked by lint can

increase drying time.

To clean

1. Pull the lint screen straight up. Roll lint off the screen with

your fingers. Do not rinse or wash screen to remove lint. Wet

lint is hard to remove.

2. Push the lint screen firmly back into place.

IMPORTANT:

■ Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

■ If lint falls off the screen into the dryer during removal, check

the exhaust hood and remove the lint. See “Venting

Requirements.”

As needed cleaning

Laundry detergent and fabric softener residue can build up on the

lint screen. This buildup can cause longer drying times for your

clothes, or cause the dryer to stop before your load is completely

dry. The screen is probably clogged if lint falls off the screen.

Clean the lint screen with a nylon brush every 6 months, or more

frequently, if it becomes clogged due to a residue buildup.

To wash

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub

lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Replace screen

in dryer.

Cleaning the Dryer Interior

To clean dryer drum

1. Make a paste with powdered laundry detergent and very

warm water.

2. Apply paste to a soft cloth.

Apply a liquid, nonflammable household cleaner to the

stained area and rub with a soft cloth until all excess dye and

stains are removed.

3. Wipe drum thoroughly with a damp cloth.

4. Tumble a load of clean cloths or towels to dry drum.

NOTE: Garments that contain unstable dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the dryer

interior. These stains are not harmful to your dryer and will not

stain future loads of clothes. Dry unstable dye items inside out to

avoid dye transfer.

Removing Accumulated Lint

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending

on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending

on dryer usage.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

Vacation and Moving Care

Vacation care

Operate your dryer only when you are at home. If you will be on

vacation or not using your dryer for an extended period of time,

you should:

1. Unplug dryer or disconnect power.

2. Close shutoff valve in gas supply line.

3. Clean lint screen. See “Cleaning the Lint Screen.”

Moving care

1. Unplug the power supply cord.

2. Close shutoff valve in gas supply line.

3. Disconnect gas supply line pipe and remove fittings attached

to dryer pipe.

4. Cap the open fuel supply line.

5. Make sure leveling legs are secure in dryer base.

6. Use masking tape to secure dryer door.

Changing the Drum Light

The dryer light automatically turns on inside the dryer drum when

you open the door.

To change the drum light

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Remove the screw located in the lower right

corner of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with a 10-watt

appliance bulb only. Replace the cover and secure with the

screw.

4. Plug in dryer or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid the cost of a service call...

Dryer Operation

Dryer will not run

■ Has a household fuse blown, or has a circuit breaker

tripped?

Replace the fuse or reset the circuit breaker. If the problem

continues, call an electrician.

■ Was a regular fuse used?

Use a time-delay fuse.

■ Is the dryer door firmly closed?

■ Was the Start button firmly pressed?

Large loads may require pressing and holding the Start

button for 2-5 seconds.

No heat

■ Has a household fuse blown, or has a circuit breaker

tripped?

The drum may be turning, but you may not have heat.

Replace the fuse or reset the circuit breaker. If the problem

continues, call an electrician.

■ Is the valve open on the gas supply line?

Unusual sounds

■ Has the dryer had a period of non-use?

If the dryer hasn’t been used for a while, there may be a

thumping sound during the first few minutes of operation.

■ Is a coin, button, or paper clip caught between the drum

and front or rear of the dryer?

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

■ Is it a gas dryer?

The gas valve clicking is a normal operating sound.

■ Are the four legs installed, and is the dryer level front to

back and side to side?

The dryer may vibrate if not properly installed. See

“Installation Instructions.”

■ Is the clothing knotted or balled up?

When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.

Dryer displaying code message

■ “PF” (power failure), check the following:

Was the drying cycle interrupted by a power failure?

Press and hold START to restart the dryer.

■ “E” Variable (E1, E2, E3) service codes:

Call for service.

Page is loading ...

Whirlpool GGW9250SU0 User guide

Brand: Whirlpool

Model: GGW9250SU0

Category: Tumble dryers

Type: User guide

This manual is also suitable for

GGW9250S

Download PDF

report

in other languages

français: Whirlpool GGW9250SU0 Mode d'emploi

Whirlpool GGW9250SU0 User guide

This manual is also suitable for

Whirlpool GGW9250SU0 User guide

in other languages

Related papers

Other documents