Marley Engineered Products FBE15002 User manual

Brand: Marley Engineered Products

Model: FBE15002

Category: Space heaters

Type: User manual

This manual is also suitable for

FBE15002

Portable Electric

Baseboard Heater

WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAU-

TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE

THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO

PERSONS, INCLUDING THE FOLLOWING:

1. Read all instructions before using the heater.

2. Use this heater only as described in this manual. Any other

use not recommended by the manufacturer may cause fire,

electric shock, or injury to persons.

3. Always plug heaters directly into a wall outlet/receptacle.

Never use with and extension cord or relocatable power tap

(outlet/power strip).

4. Do not operate any heater with a damaged cord or plug or

after the heater malfunctions, has been dropped or dam-

aged in any manner. Discard heater or return to an author-

ized service facility for examination, and/or repair.

5. Do not run cord under carpeting. Do not cover cord with

throw rugs, runners, or similar coverings. Do not route cord

under furniture or appliances. Arrange cord away from traf-

fic area and where it will not be tripped over.

6. Always unplug heater when not in use.

7. To disconnect, rotate thermostat to the LO set point or flip

ON-OFF switch to off. Then grip plug (not cord) and pull

from outlet.

8. A heater has hot and arcing or sparking parts inside. Do not

use in areas where gasoline or flammable liquids are used

or stored.

9. This heater is hot when in use. To avoid burns, do not let

bare skin touch hot surfaces. Keep combustible materials,

such as furniture, pillows, bedding, papers, clothes, and cur-

tains away from heater.

10. To prevent a possible fire, do not block air intakes or

exhaust in any manner. Do not use on soft surfaces, like a

bed, where openings may become blocked.

11. Do not insert or allow foreign objects to enter any ventilation

or exhaust opening as this may cause an electric shock or

fire, or damage the heater.

12. This heater is not intended for use in bathrooms, laundry

areas and similar indoor (wet) locations. Never locate

heater where it may fall into a bathtub or other water con-

tainer.

13. Do not operate heater without support legs installed – see

ASSEMBLY INSTRUCTIONS.

14. This heater is intended for floor use only. Do not place on

shelf, table, or any location except the floor.

SAVE THESE INSTRUCTIONS

Installation, Operation & Maintenance Instructions

WARNING

MODEL

NO.

VOLTS WATTS AMPS

1500/1000

BTU/HR

FBE15002 120V

12.5/8.3

5120/3413

GENERAL

This heater is designed to provide years of efficient, trouble free operation as a supplementary heat source for comfort heating in

residential applications. Use of this product in any manner not described herein will void the warranty and could result in injury,

damage to property, or permanent damage to heater.

IMPORTANT INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

Heater Assembly

1. After removing the heater from its carton, carefully inspect

it for possible shipping damage. Return damaged units to

point of purchase.

2. Remove plastic support leg extensions from packaging.

Line up the slots and slide extension into end panels as

shown. (See Figure 1).

OPERATION INSTRUCTIONS

IMPORTANT NOTICE:

This heater is a major electrical appli-

ance and requires adequate electrical power. The outlet to

which this heater is connected must be a 120 volt (AC) circuit

protected by a 15 or 20 amp fuse or circuit breaker. No other

major electrical appliance should be operated in the same circuit

as the heater.

Care must be given in locating and using the heater to avoid

blocking the heater in any way to allow air to flow freely through

the heater. Keeping the heater clean will also help improve the

efficiency and prevent overheating.

WARNING:

The heater plug must fit tightly into outlet. A loose

fitting or worn outlet may allow for the plug connection to heat,

damage to the plug and/or outlet and may cause a fire. If outlet

is loose or worn, discontinue using heater until the outlet can be

replaced.

SPECIAL NOTE:

You may notice a new smell coming from

your heater during initial use. It should go away within the first

few hours of operation. You may also notice it does not heat up

immediately. Because of the special tubular element design, it

takes a few minutes before you can feel the warmth through the

cabinet.

1. Never place anything on top of the heater. It is recommend-

ed that a space of at least 12 inches (30 mm) be maintained

around the heater.

2. When moving heater, turn heater controls to LO or ON-OFF

switch to OFF and remove plug from outlet. Allow heater to

cool and then pick up by grasping heater cabinet along top

and back side.

3. Do not allow heater to operate in any position except as

shown in this manual.

Heater Operation

1. Heater must be properly installed before operation.

2. The FBE15002 is provided with a POSITIVE OFF thermo-

stat. In addition to the thermostat, the FBE15002 has a

LO/HI heat selection switch.

3. Operation:

a. Plug heater power supply into 120 volt outlet.

b. Move heat selection switch to the left position for LO

(1000 watts) or to the right for HI (1500 watts).

c. Rotate the thermostat knob clockwise until it stops.

4. Allow the heater to operate normally until the room tempera-

ture is comfortable to you. Then simply rotate the thermostat

knob to the left until the thermostat clicks. The thermostat

will then automatically turn your heater on and off to maintain

the room temperature.

5. To adjust the room temperature, rotation of the thermostat

knob to the right will increase the heater output while rotation

of the thermostat knob to the left will decrease the output.

The numbers on the thermostat knob are for reference only

and may help you in setting and adjusting the heater output

for your comfort.

6. To turn heater off, rotate the thermostat knob to the left until

it stops. Always unplug heater when not in use.

MAINTENANCE INSTRUCTIONS

For efficient and safe operation and to extend the life of your

heater it should be cleaned and inspected for damage at least

annually (preferably at the beginning of the heater season) or

more often in dirty environments. Other than cleaning, your

heaters require no other preventative maintenance.

1. Heater cabinet may be cleaned using a damp cloth to

remove dust that may have accumulated on surfaces. Do

not use harsh cleaners and waxes on surfaces since these

could damage the finish or discolor in use.

2. A vacuum cleaner and / or compressed air may be used to

remove dust and lint that may have accumulated inside

heater around element fins.

3. After cleaning and servicing, check units to make sure they

are operating properly.

THERMAL SAFETY SWITCH:

Your heater is provided with an

automatic-resetting thermal safety switch that will disconnect

power to the heating element should the heater be placed into

an abnormal condition (such as a blockage) to prevent a fire.

When the heater cools, the safety switch will reset allowing the

heater to return to normal operation.

FINS MAY CAUSE CUTS, DO NOT TOUCH

TO PREVENT A POSSIBLE ELECTRIC SHOCK, ALWAYS

UNPLUG HEATER FROM OUTLET BEFORE CLEANING OR

SERVICING.

ALLOW HEATER TO COOL BEFORE CLEANING TO

PREVENT A POSSIBLE BURN.

Correct

Incorrect

Figure 1

05/10

Part No. 5200-2307-002

ECR 38723

LIMITED WARRANTY

All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of installation.

This warranty does not apply to damage from accident, misuse, or alteration; nor where the connected voltage is more than 5% above the nameplate voltage; nor to

equipment improperly installed or wired or maintained in violation of the product’s installation instructions. All claims for warranty work must be accompanied by proof of

the date of installation.

The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred to return products

to Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the nearest Marley authorized service cen-

ter or the Marley Engineered Products Service Center, and we will repair or replace, at our option, at no charge to you with return freight paid by Marley. It is agreed that

such repair or replacement is the exclusive remedy available from Marley Engineered Products.

THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED FROM

THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALL NOT BE LIABLE FOR CONSEQUENTIAL DAMAGES ARISING WITH RESPECT TO THE

PRODUCT, WHETHER BASED UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CONTRACT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state.

For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328. Merchandise returned to the fac-

tory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products. When requesting return authorization,

include all catalog numbers shown on the products.

HOW TO OBTAIN WARRANTY SERVICE AND

WARRANTY PARTS PLUS GENERAL INFORMATION

1. Warranty Service or Parts

1-800-642-4328

2. Purchase Replacement Parts

1-800-654-3545

3. General Product Information

www.marleymep.com

Note:

When obtaining service always have the following:

1. Model number of the product