Rexel Auto+ 500M User manual

Category
Paper shredders
Type
User manual

This manual is also suitable for

GB
6 register this product online at www.accobrands.com
To guard against injury, the following basic safety precautions must be observed in the set-up of this
product.
Ensure the machine is plugged into an easily accessible power outlet, and ensure the cable is not
likely to trip up a passer by.
Any attempt to repair this unit by unqualied personnel will invalidate the warranty. Please return to
supplier.
Unplug your shredder before moving it or when it is not in use for an extended period of time.
Do NOT operate with a damaged power supply cord or plug, after it malfunctions, or after it has
been damaged in any manner.
Do NOT overload electrical outlets beyond capacity as this can result in re or electrical shock.
The socket-outlet should be near the equipment and should be easily accessible.
Do NOT alter the attachment plug. The plug is congured for the appropriate electrical supply.
Do NOT use near water.
Do NOT use aerosol dusters or cleaners.
Do NOT spray anything into the shredder.
Do NOT load the auto-feed chamber with unopened junk mail, magazines, bound documents etc.
Although this shredder has been designed to comply with UL 60950-1 EN 60950-1 safety standards
including the “probe accessibility tests”, do not operate the shredder near children or pets.
autofeed technology
The Auto+ 500X and 500M has been designed to automatically shred up to 500 sheets from the
auto-feed chamber and up to 9/10 sheets through the manual feed slot. The auto-feed mechanism
has been designed to handle paper fastened with staples and paper clips and to only pull a few
sheets of paper into the cutting mechanism to minimise the risk of paper jams.
GB
AUTO+ 500X&500M
SHREDDERS 7
control panel and indicators
Jam Free indicator – This alerts
the user when too much paper is
fed into the manual feed slot (see
section on Jam Free Technology).
U
C
Paper Loading Door/Bin Door
Open or Bin Full indicator –
This means either:
• Loading door is open
• Bin is open
• Bin is full
Lock indicator – This means the
paper loading door is locked (during
shredding).
Oil level indicator
Oiling in Operation indicator
Paper jam indicator – This means
there is a paper jam in the auto feed
chamber.
If this symbol is ashing the
shredder is attempting to clear a
paper jam automatically.
If this symbol is permanently
illuminated red please follow the
instructions under ‘Rare Occasion
of Jamming’.
Continuous Jam Boost
Auto
Reverse
Loading Door Locking
Mechanism – PIN Password
Buttons – Enter a four digit code
to lock the loading door during
shredding.
warning symbols
Sheet capacity of manual feed
entry slot.
10
This means no aerosols.
This means keep children away
from shredder.
This means you should be careful
because long hair can become
entangled in the cutting head.
This means don’t reach into the
feed opening of the cutting head.
This means be careful of loose
jewellery which could become
entangeld in the cutting head.
This means no oil lubrication,
use Rexel oil sheets only.
This means be careful of ties and
other loose clothing which could
become entangled in the cutting
head.
This means the shredder can
accept small paperclips.
This means the shredder can
accept small staples.
Safety First
GB
8 register this product online at www.accobrands.com
Auto+ 500X/500M shredding capability
Auto+ 500X/500M CAN shred the following:
• 500 sheets
Stapled paper, 25mm within the corner
26/6 and 24/6 or smaller staples
Small sized paper loaded centrally
500 sheets
Paper clip paper, 25mm within the corner (500X through manual feed slot ONLY)
Capable of shredding small/medium paper clips (max. wire thickness = 0.9 mm)
>80/100gsm paper (through manual feed slot ONLY)
A3 folded in half max. 2 sheets
500 sheets
80 gsm paper
- A4 - 210mm x 297mm
- A5 - 148mm x 210mm
- A3 single sheet folded in half to make A4
Auto+ 500X/500M CAN shred (through the manual feed slot):
Thick paper or
card.
Multiple folded
sheets (e.g. A3
sheets folded in
half).
Unopened mail
(e.g. junk mail).
Glossy paper or
a sheet covered
with print on both
sides.
Auto+ 500X/500M CANNOT shred the following:
Large clips.
Check the length
of the paperclip
is not longer than
32mm.
Heavy duty
staples. Check
the staple leg
length is not
greater than
6mm.
Bound
documents
Bulldog clips
Magazines or
other documents
bound by multiple
staples or clips.
Adhesive labels.
Plastic sheets,
laminated
documents,
plastic folders.
GB
AUTO+ 500X&500M
SHREDDERS 9
1. initial setup
The shredder is designed to automatically lubricate the cutting mechanism as required to ensure
the product continues to work to its maximum performance and to extend the product life. Please
follow the operation instruction before turning on the shredder for the rst time. The 60ml bottle
of oil* is sucient to allow the shredder to start for the rst time and to operate continuously for
about one hours shredding before the reservoir will need relling. When the ‘Oil Rell’ indicator is
illuminated (
), ip up the oil reservoir cap and rell the oil reservoir using a bottle of standard
Rexel oil (1760049)*. The automatic oiling operation (
) last approximately two seconds and
you will hear the distribution pump during this time. Auto-oiling operates after 15 minutes of
shredding time.
bin or loading door open safety function
As a safety precaution, if the bin or loading door is opened during shredding, the shredder will stop
and the bin full indicator will illuminate (
).
jam free technology in manual feed slot
Sensors in the paper feed area measure the thickness of paper about to be shredded. The
ability to shred or not is communicated through red and green lighting. Green means that the
stack of paper is within the shredders sheet capacity and OK to shred. Red means that you
have too much paper, remove some sheets in order to shred.
Given that you are unable to shred more sheets of paper than the shredder is capable of
shredding, paper jams are prevented.
This prevents wasting time reversing paper and unblocking jams not to mention the mess it
can create.
intelligent help
1 In the unlikely event of the shredder jamming, the Auto+ 500X and 500M will stop shredding,
and the jam icon will blink in orange.
2 The shredder will illuminate the FWD (
) and REV (
) buttons in the sequence necessary
to clear the jam.
3 If the jam cannot be intelligentally cleared, the jam icon (
) will illuminate in red. At this point
open the auto feed chamber to clear any jammed material.
* ACCO Brands Europe accepts no liability for product performance or safety when other types or brands of lubricants are used on
any part(s) of this machine.
automatic jam clearance
Intelligent Jam Clearance: In the unlikely event of the shredder jamming, the Auto+ 500X and 500M
will automatically reverse and forward the engine three times to clear a jam. During this operation
the Paper Jam indicator will ash (
).
GB
10 register this product online at www.accobrands.com
2. operation
1 After unpacking the product pull out the shredder bag frame and remove the CD shard tray,
which sits on top of the bag frame. Store this tray on the product as shown and use when you
shred CDs.
2 Lift up the loading door and open oil ap.
3 Remove oil cap and ll up the reservoir using the 60ml bottle of oil provided. Replace the cap.
4 Connect the shredder to mains supply.
5 Check that the on/o switch at the back of the machine is switched to the ‘ON’ position.
6 Press and hold down the Auto button (
) for 5 seconds to start the pump and prime the
system. Only required when the product is used for the rst time.
7 To load the shredder, simply lift the loading door handle to open the loading door and insert
documents. You can open the door further to 90 degrees for easier access if required Load up to
500 sheets at a time into the feed chamber.
Do not ll above the MAX level, this could damage the shredder.
8 The shredder will start the shredding cycle automatically ONLY after closing the loading door.
If there is paper in the Autofeed chamber after rst attempt, open and re-close the paper loading
door a second time.
Attention: If required you can now lock the loading door by entering a 4 digit code (see Locking
the Paper Loading Door section).
9 If you only have up to 9/10 sheets to shred, you can use the manual feed slot, provided the auto
feed chamber is empty.
10 Insert paper to be shredded into the feed area. The shredder will detect the paper and start
automatically.
11 If the shredder is left in auto mode for more than 2 minutes without being used, the shredder will
automatically turn back to sleep mode in order to save power.
12 The shredder will automatically ‘wake up’ from sleep mode when paper is inserted into the
shred mouth or you open the loading door. There is no need to press the Auto button (
).
3. reverse function
1 Should you wish to reverse paper out whilst shredding, a reverse button (
) has been tted for
your convenience.
2 Reverse the paper out then turn the machine o using the ON/OFF switch at the rear of the
shredder. Remove the paper from the manual feed slot (if being used) or open the loading door,
remove the remaining stack of paper, then pull the jammed paper free of the cutting mechanism.
3 To resume shredding, turn the shredder on using the ON/OFF switch at the rear of the shredder.
Return the switch to the auto position (
).
GB
AUTO+ 500X&500M
SHREDDERS 11
Rexel encourages customers to recycle shredded paper.
Please note that shredded paper cannot be recycled if mixed with credit card shards.
If recycling, please separate shredded paper and credit cards.
4. locking the paper loading door
For additional security the paper loading door can be locked during the shredding of condential
material.
To lock shredder:
1
Place documents in tray. Close paper loading door.
2
Press any 4 digits. REMEMBER YOUR CODE!
Shredder unlocks automatically when:
4 digit code is re-entered.
Shredding is complete.
Shredder is inactive for 30 minutes (but documents remain in tray)
7. bin full
The shredder will not function when the bin is full and the bin full symbol (
) is illuminated.
You should empty the bin.
• Open the door and slide out the waste sack support frame.
• Carefully remove the waste sack from the frame.
5. CD/DVD shredding
A separate CD/DVD tray is provided to collect the shredded CD/DVD shards. Ensure that this is
correctly mounted onto the standard shredder bag frame before shredding.
1 Lift up the paper loading door.
2 Always insert CDs/DVDs in the CD/DVD slot. Only shred one CD/DVD at a time.
3 Close the paper loading door.
4 Empty the CD/DVD bin after 8 CDs/DVDs to avoid waste spilling over into the paper waste bin.
5 Remove the CDs/DVDs tray before recommencing to shred paper and store on the side of the
shredder.
6. credit card shredding
The Auto+ 500X and 500M can shred credit cards. Switch the shredder to auto mode, then;
1 Lift up the paper loading door.
2 Insert the credit card into the roller as shown. Only shred one credit card at a time.
3 Close the paper loading door.
GB
12 register this product online at www.accobrands.com
shredder accessories
We recommend that a paper waste sack for
recycling shredded paper is used on all models.
Accessory Part Number Box Quantity
Recycling Waste
Sack
Plastic Waste
Sack
Oil* Rell Bottle
1765030EU
40060
1760049
50
100
8
self-cleaning cutters
After emptying and replacing a full bin, the shredder will run in forward for 4 seconds, stop for
2 seconds and then reverse for 4 seconds to clear away any remaining paper from the cutter
mechanism. This unique ‘self-cleaning’ mechanism is additional jam prevention technology
from Rexel.
8. comb bind removal hooks
Note – Use only on standard comb bind strips.
1 Open bin door.
2 Place document onto the comb bind hooks.
3 Pull down on the document to remove comb strip.
9. maintenance
The rollers on the auto-feed mechanism may become dirty over time, please wipe clean with a dry
cloth to maintain maximum product performance.
The auto-start infra-red sensor, located in the paper feed entry-slot, can occasionally become
covered in paper-dust causing the shredder to run despite no paper being fed into the machine.
Switch the shredder o at the rear of the machine and carefully clean the sensor using a cotton-
swab.
service
We recommend these machines are serviced every 6 to 12 months by a Rexel service engineer –
see back of this booklet for the contact details of your local service centre and for enquiries about
maintenance contracts.
* ACCO Brands Europe accepts no liability for product performance or safety when other types or brands of lubricants are used on
any part(s) of this machine.
GB
AUTO+ 500X&500M
SHREDDERS 13
guarantee
ACCO Brands Europe (ACCO) warrants its products and their parts against defects in materials and
workmanship under normal use for a period of 24 months from the original date of purchase.
During this period we will repair or replace a defective product or part subject to the following warranty conditions:
The warranty applies only to defects in materials and workmanship under normal use and does not extend to
damage to the Product or parts which result from:-
- alteration, repair, modication or service carried out by anyone other than an authorised ACCO service centre.
- accident, neglect, abuse or misuse owing to failure to comply with the normal operating procedures for a
product of this type.
Depending on the diagnostics and the model type, we will either arrange a service call by an engineer or arrange
with you return of the product to ACCO. ACCO will, at its discretion, in accordance with law, either
- repair the shredder using either new or refurbished parts, or
- replace the shredder with a new or refurbished shredder that is equivalent to the shredder being replaced.
Nothing in this Warranty shall have the eect of excluding the liability of ACCO in respect of death and personal
injury caused by the negligence of ACCO. This Warranty is oered (subject to these terms and conditions) in
addition to, and does not aect, your statutory rights.
If you experience a technical fault, please contact the ACCO customer helpdesk (see back cover)
Additional Guarantee
ACCO Brands Europe guarantees the cutting blades of the shredder to be free from defects in material and
workmanship for 20 years from the date of purchase by the original consumer.
*Please note that the cutter blades will be progressively worn down by shredding fastened sheets (staples and
paperclips) - this is not covered in the warranty. The Auto+ 500X has been design to shred up to 50 credit cards
and 50 CD/DVDs in the standard 2 year warranty period. Any excessive credit card or CD/DVD shredding will
invalidate the extended cutter warranty.
These conditions shall in all respects be governed and construed in accordance with English Law and subject to
the exclusive jurisdiction of the English Courts.
Australian Customers
This guarantee does not apply to Australian customers.
See warranty on page 144.
Sheet capacity:
Manual feed slot
10 sheets (80gsm)
Sheet capacity:
Autofeed chamber
500 sheets (80gsm)
Duty Cycle Continuous
Run time from cold Continuous
Volts / Hz 230V / 50Hz
Amperage 1.2 Amps
Motor Watts 270 Watts
Sheet capacity:
Manual feed slot
9 sheets (80gsm)
Sheet capacity:
Autofeed chamber
500 sheets (80gsm)
Duty Cycle Continuous
Run time from cold Continuous
Volts / Hz 230V / 50Hz
Amperage 1.7 Amps
Motor Watts 390 Watts
technical specifications
Rexel Auto+ 500X Rexel Auto+ 500M
service addresses
ACCO Service Division,
Hereward Rise, Halesowen, West Midlands, B62 8AN
Tel: 0845 658 6600 Fax: 0870 421 5576 www.acco.co.uk/service
GB
Acco Brands France SAS,
Service après-vente, ZAC Excellence 2000, 6 rue Robert Schuman, 21800 Chevigny Saint Sauveur
Tel: +33 3 80 68 60 30 Fax: +33 3 80 68 60 49 [email protected]
F
ACCO Deutschland GmbH & Co. KG,
Arnoldstrasse 5, 73614 Schorndorf, Germany
Tel: + 49 7181 887 120 Fax:+ 49 7181 887 198 info.de@acco.com
D
ACCO Deutschland GmbH & Co. KG,
Arnoldstrasse 5, 73614 Schorndorf, Germany
Tel: + 49 7181 887 120 Fax:+ 49 7181 887 198 info.de@acco.com
A
ACCO Brands Iberia SL,
P Isaac Peral 19, 28820 Coslada (Madrid)
Tel: 902 500 182 ext. 2 Fax: 91 309 6412 servicio.tecnico@acco.com
E
ACCO Brands Italia Srl,
Servizio post-vendita, Via Oberdan, 33, 28070 Tornaco (NO)
Tel: 800-87-86-16 Fax: 0321-88-01-27 servizio.clienti@acco.com
I
ACCO Brands Benelux B.V.,
Peppelkade 64, 3992AK Houten, Nederland/Les Pays-Bas
Tel: 0800-73362 Fax: 02-4140784 [email protected] www.accobenelux.be
B
ACCO Brands Nordic AB,
Makadamgatan 5, 254 64 Helsingborg, Sweden
Tel: +46 42 38 36 00 Fax: +46 42 38 36 10 service.nordic@acco.com
DK
ACCO Brands Nordic AB,
Makadamgatan 5, 254 64 Helsingborg, Sweden
Tel: +46 42 38 36 00 Fax: +46 42 38 36 10 service.nordic@acco.com
EST
XERTEC a.s.,
Kloknerova 2278/24 (vchod z ulice Koštířova, budova CeWe Color - Fotolab), 148 00 Praha 4 -
Chodov
Tel: 225 004 411 Fax: 225 004 162 [email protected] http://www.xertec.cz
CZ
OPI Customer Service
Tel.: +359 2 80 99 166 [email protected]
H
Pelikan Artline Pty Ltd,
2 Coronation Avenue, Kings Park, NSW, Australia 2148
Tel: +61 2 9674 9000 Fax: +61 2 9674 0910 [email protected]
AUS
ACCO Brands Schweiz GmbH,
Gewerbestrasse 8, CH-8212 Neuhausen a. Rheinfall
Tel: +41 (0)52 674 01 74 Fax: +41 (0)52 674 01 75 info[email protected]
CH
ACCO-Rexel Ltd,
Clonshaugh Business & Technology Park, Clonshaugh, Dublin 17, Ireland
Tel: 01 816 4346 Fax: 01 816 4302 [email protected] www.accorexel.ie
IRL
ACCO Brands Asia Pte Ltd,
47 Ayer Rajah Crescent, #05-08/17, Singapore 139947
Tel: +65 6776 0195 Fax: +65 6779 1041 [email protected]
IND
ACCO Brands Asia Pte Ltd,
47 Ayer Rajah Crescent, #05-08/17, Singapore 139947
Tel: +65 6776 0195 Fax: +65 6779 1041 [email protected]
BD
142
ACCO Brands Iberia SL,
P Isaac Peral 19, 28820 Coslada (Madrid)
Tel: 902 500 182 ext. 2 Fax: 91 309 6412 servicio.tecnico@acco.com
P
ACCO Brands Benelux B.V.,
Peppelkade 64, 3992AK Houten, Nederland/Les Pays-Bas
Tel: 0800-21132 Fax: 02-4140784 [email protected] www.accobenelux.be
LUX
ACCO Brands Benelux B.V.,
Peppelkade 64, 3992AK Houten, Nederland/Les Pays-Bas
Tel: 030-6346060 Fax: 030-6346070 [email protected] www.accobenelux.nl
NL
ACCO Brands Nordic AB,
Makadamgatan 5, 254 64 Helsingborg, Sweden
Tel: +46 42 38 36 00 Fax: +46 42 38 36 10 service.nordic@acco.com
S
ACCO Brands Nordic AB,
Makadamgatan 5, 254 64 Helsingborg, Sweden
Tel: +46 42 38 36 00 Fax: +46 42 38 36 10 service.nordic@acco.com
N
ACCO Brands Nordic AB,
Makadamgatan 5, 254 64 Helsingborg, Sweden
Tel: +46 42 38 36 00 Fax: +46 42 38 36 10 service.nordic@acco.com
IS
ACCO Brands Nordic AB,
Makadamgatan 5, 254 64 Helsingborg, Sweden
Tel: +46 42 38 36 00 Fax: +46 42 38 36 10 service.nordic@acco.com
LV
ACCO Brands Nordic AB,
Makadamgatan 5, 254 64 Helsingborg, Sweden
Tel: +46 42 38 36 00 Fax: +46 42 38 36 10 service.nordic@acco.com
LT
XERTEC a.s.,
Kloknerova 2278/24 (vchod z ulice Koštířova, budova CeWe Color - Fotolab), 148 00 Praha 4 -
Chodov
Tel: 225 004 411 Fax: 225 004 162 [email protected] http://www.xertec.cz
SK
ACCO Polska Sp. z o.o,
Al. Jerozolimskie 184, 02-486 Warszawa
Tel.+48 22 570-18-29 fax +48 22 570-18-33 www.acco.pl
PL
Представительство компании «АККО Дойчланд ГМБХ и КО. КГ»,
Россия 105005, Москва, Денисовский пер., д.26
Тел: (495) 933-51-63 Факс: (495) 933-51-64
RUS
DataLux Distribution Company,
03151, Киев, Очаковская, 5/6, оф.110.3
Tel: + 380 (44) 498 4956 ext. 2324 Fax: + 380 (44) 275 9999
UA
ACCO Brands Asia Pte Ltd,
47 Ayer Rajah Crescent, #05-08/17, Singapore 139947
Tel: +65 6776 0195 Fax: +65 6779 1041 [email protected]
PAK
GBC-Japan K.K.,
14F Harmony Tower, 1-32-2 Honcho, Nakano-ku, Tokyo 164-8721
Tel: (81)-03-5351-1801 Fax: (81)-03-5351-1831 [email protected] www.gbc-japan.co.jp
JPN
Rexel Oce Products (PTY) Ltd,
Crusher Road, Crown Ext.3, PO Box 102, Crown Mines, Johannesburg 2025, South Africa
Tel: +27 (0)11 226 3300 service@rexelsa.co.za
ZA
143
144
warranty (in Australia)
ACCO Australia warrants its products and their parts against defects in materials and workmanship under normal
use for a period of 24 months from the original date of purchase (please retain proof of purchase). During this
period we will repair or replace a defective product or part subject to the following warranty conditions:
The warranty applies only to defects in materials and workmanship under normal use and does not extend to
damage to the Product or parts which result from:-
Alteration, repair, modication or service carried out by anyone other than an authorised ACCO service centre.
Accident, neglect, abuse or misuse owing to failure to comply with the normal operating procedures for a
product of this type.
Nothing in this warranty shall have the eect of excluding the liability of ACCO in respect of death and personal
injury caused by the negligence of ACCO. This Warranty is oered (subject to these terms and conditions) in
addition to, and does not aect your rights and remedies under the Australian Consumer Law and other laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
For any questions relating to your warranty, please contact your local service agent.
Additional Guarantee
ACCO Australia guarantees the cutting blades of the shredder to be free from defects in material and
workmanship for an extended warranty period from the date of purchase by the original consumer. Please refer to
the table below for the cutter warranty period applicable to your shredder model.
Shredder Models Extended Cutter
Warranty Period
Style, Style+, V35WS, V30WS, Alpha 3
Auto+50, Auto+60 5
Promax V65WS, Promax V60WS, Prostyle, Prostyle+, RES1223, REX1023,
REM723, SC170, CC175, Auto+80
7
V120, V125, P180CD, P185, RSS2030, RSX1630, RSS2232, RSX1632,
RSM1130, Auto+100, Auto+175, Auto+200
10
RDS2250, RDX1850, RDSM750, RDM1150, RDS2270, RDX2070,
RDSM770, RDM1170, Auto+250, Auto+300, Auto+500, Auto+750, RLS32,
RLX20, RLM11, RLSM9, RLWX19, RLWX30, RLWSFM9, RLWM26,
RLWX39, RLWS47, RLWX25, RLWS35
20
*Please note that the cutter blades will be progressively worn down by shredding fastened sheets (staples and
paperclips)- this is not covered by this warranty. Excessive credit card and CD shredding will also invalidate the
extended cutter warranty. Some shredder models are NOT designed to shred CDs. Any attempt to do so will
invalidate the warranty.
How to Make a Claim
To make a claim under this warranty, contact the ACCO Australia Customer Service Team with your proof of
original purchase handy:
ACCO Australia
Level 2, 8 Lord St
Botany NSW 2019
Ph: 1300 366 376
E: sales.au@acco.com
F: 1300 360 944
The customer service team member will advise whether your product should be repaired, replaced or returned
and advise the next step for you to take. If the product is validated as still under warranty and deemed faulty,
ACCO will bear costs involved with the warranty process. To claim expenses incurred in making a claim under this
warranty, contact our Customer Service Team on the details above.
www.accobrands.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146

Rexel Auto+ 500M User manual

Category
Paper shredders
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI