PROEL SW110P User manual

Brand: PROEL

Model: SW110P

Category: Subwoofers

Type: User manual

This manual is also suitable for

USER’S MANUAL

MANUALE UTENTE

www.proel.com

SW110

SUBWOOFER

FCC COMPLIANCE NOTICE

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation.

CAUTION: Changes or modiﬁ cations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its

working life. To prevent possible harm to the enviroment or human health from uncontrolled waste disposal, please separate this from other

types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either

the retailer where they purchased this product, or their local government ofﬁ ce, for details of where and how they can take this item for

environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

The lightning ﬂ ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure, that may be of sufﬁ cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

The information contained in this publication has been carefully prepared and checked. However no responsibility will be taken for any errors. All

rights are reserved and this document cannot be copied, photocopied or reproduced in part or completely without written consent being obtained

in advance from PROEL. PROEL reserves the right to make any aesthetic, functional or design modiﬁ cation to any of its products without any prior

notice. PROEL assumes no responsibility for the use or application of the products or circuits described herein.

Il marchio riportato sul prodotto o sulla documentazione indica che il prodotto non deve essere smaltito con altri riﬁ uti domestici al termine

del ciclo di vita. Per evitare eventuali danni all’ambiente si invita l’utente a separare questo prodotto da altri tipi di riﬁ uti e di riciclarlo in

maniera responsabile per favorire il riutilizzo sostenibile delle risorse materiali. Gli utenti domestici sono invitati a contattare il rivenditore

presso il quale è stato acquistato il prodotto o l’ufﬁ cio locale preposto per tutte le informazioni relative alla raccolta differenziata e al

riciclaggio per questo tipo di prodotto. Gli utenti aziendali sono invitati a contattare il proprio fornitore e veriﬁ care i termini e le condizioni

del contratto di acquisto. Questo prodotto non deve essere smaltito unitamente ad altri riﬁ uti commerciali.

Il simbolo del lampo con freccia in un triangolo equilatero intende avvertire l'utilizzatore per la presenza di "tensioni pericolose" non isolate

all'interno dell'involucro del prodotto, che possono avere una intensità sufﬁ ciente a costituire rischio di scossa elettrica alle persone.

Il punto esclamativo in un triangolo equilatero intende avvertire l'utilizzatore per la presenza di importanti istruzioni per l'utilizzo e la

manutenzione nella documentazione che accompagna il prodotto.

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia non è assunta alcuna responsabilità per

eventuali inesattezze. Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo

consenso scritto della PROEL. PROEL si riserva il diritto di apportare senza preavviso cambiamenti e modiﬁ che estetiche, funzionali o di design a

ciascun proprio prodotto. PROEL non assume alcuna responsabilità sull’uso o sul l’applicazione dei prodotti o dei circuiti qui descritti.

INDICE / INDEX

Index

TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . 4

FREQUENCY RESPONSE . . . . . . . . . . . . . . . . . . . . . . 4

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

PASSIVE - CONTROL PANEL (FIG. 1) . . . . . . . . . . . . 5

PASSIVE -CONFIGURATION EXAMPLES (FIG. 2) . . 6

ACTIVE - CONTROL PANEL (FIG. 3) . . . . . . . . . . . . . 7

ACTIVE - CONNECTIONS (FIG. 4) . . . . . . . . . . . . . . . 7

ACTIVE - CONFIGURATION EXAMPLES (FIG. 5) . . . 8

SAFETY AND PRECAUTIONS . . . . . . . . . . . . . . . . . . 9

IN CASE OF FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . 9

CE CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

PACKAGING, SHIPPING AND COMPLAINT . . . . . 10

WARRANTY AND PRODUCTS RETURN . . . . . . . . . 10

INSTALLATION AND DISCLAIMER . . . . . . . . . . . . . 10

POWER SUPPLY AND MAINTENANCE . . . . . . . . . 10

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . 11

SW110P - PASSIVE VERSION ( FIG. 1 / 2 ) . . . . . . . 11

SW110A - ACTIVE VERSION ( FIG. 3 / 4 / 5 ) . . . . . 12

Indice

SPECIFICHE TECNICHE . . . . . . . . . . . . . . . . . . . . . . . 4

RISPOSTA IN FREQUENZA . . . . . . . . . . . . . . . . . . . . 4

ACCESSORI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

DIMENSIONI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

PASSIVO - PANNELLO DI CONTROLLO (FIG. 1) . . . 5

PASSIVO - ESEMPI DI CONFIGURAZIONE (FIG. 2) . 6

ATTIVO - PANNELLO DI CONTROLLO (FIG. 3) . . . . . 7

ATTIVO - CONNESSIONI (FIG. 4) . . . . . . . . . . . . . . . . 7

ATTIVO - ESEMPI DI CONFIGURAZIONE (FIG. 5) . . 8

AVVERTENZE PER LA SICUREZZA . . . . . . . . . . . . . 14

IN CASO DI GUASTO . . . . . . . . . . . . . . . . . . . . . . . . 14

PROBLEMATICHE COMUNI . . . . . . . . . . . . . . . . . . . 14

CONFORMITÀ CE . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

IMBALLAGGIO, TRASPORTO E RECLAMI . . . . . . . 15

GARANZIE E RESI . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

INSTALLAZIONE E LIMITAZIONI D’USO . . . . . . . . 15

ALIMENTAZIONE E MANUTENZIONE . . . . . . . . . . 15

INFORMAZIONI GENERALI . . . . . . . . . . . . . . . . . . . 16

SW110P - VERSIONE PASSIVA ( FIG. 1 / 2 ) . . . . . . 16

SW110A - VERSIONE ATTIVA (FIG. 3 / 4 / 5 ) . . . . . 17

speciﬁ cations

MODEL SW110P SW110A

System type Bandpass enclosure subwoofer Bandpass enclosure subwoofer

Nominal Impedance 8 + 8 ohm -

Power Handling (continuous) 100 + 100 W -

Power Handling (peak) 200 + 200 W -

Frequency Response (-10dB) 46 Hz - 200 Hz 46 Hz - 180 Hz

Sensitivity 95 dBspl @ 1 W/1 m -

Crossover Frequency 160 Hz - 12 dB/oct LP, 6 dB/oct HP 125 / 160 Hz - 24 dB/oct LP, 12 dB/oct HP

Loudspeaker 10'' woofer - 2.5" VC 10'' woofer - 2.5" VC

Ampliﬁ er Continuous Power - 250 W Class D

Max SPL 121 dBspl 122 dBspl

Connectors 2 x NEUTRIK SPEAKON (IN/LINK) IN: 2 x NEUTRIK COMBO

OUT: 2 x NEUTRIK XLR-M

LINK: 2 x NEUTRIK XLR-M

Controls - Level, GND lift

Filter Frequency, Phase

Input Impedance - 30 kohm balanced

15 kohm unbalanced

Input Sensitivity - 0 dBu / 0.775 V

Angular coverage omnidirectional omnidirectional

Construction 15 mm plywood 15 mm plywood

Finishing Anti-scratch BLACK paint ﬁ nish Anti-scratch BLACK paint ﬁ nish

Mounting Pole 1 1

Transport 1 x handle 1 x handle

Weight 15.5 kg (34.2 lb) 18 kg (39.7 lb)

Dimensions (W x H x D) 520 x 335 x 350 mm 520 x 335 x 350 mm

Power Supply - 240-230 VAC or 120 VAC - 50/60 Hz

with voltage selector

Maximun Consumption - 260 VA

Rated Consumption* - 70 VA

* Rated consumption is measured with pink noise with a crest factor of 12 dB, this can be considered a standard music program.

TECHNICAL SPECIFICATIONS SPECIFICHE TECNICHE

FREQUENCY RESPONSE RISPOSTA IN FREQUENZA

SW110ASW110P

500200

100

2020

-10

-20

-30

125 Hz FILTER 160 Hz FILTER

500200

100

2020

100

WITH INTERNAL FILTER

ACCESSORIES ACCESSORI

KP210 - SPEAKER STAND - SUBWOOFER / SPEAKER ALUMINIUM BLACK FINISH

SUPPORTO ALTOPARLANTI - SUBWOOFER / ALTOPARLANTE ALLUMINIO FINITURA NERO

dimensions, FIG. 1

DIMENSIONS DIMENSIONI

52 cm

20.5"

33,5 cm

13.2"

35 cm

13.8"

Mounting Pole

M10 Flying point

PASSIVE - CONTROL PANEL (FIG. 1) PASSIVO - PANNELLO DI CONTROLLO (FIG. 1)

FIG. 2

PASSIVE -CONFIGURATION EXAMPLES (FIG. 2) PASSIVO-ESEMPI DI CONFIGURAZIONE (FIG. 2)

PROEL suggested equipment:

HPX900 power amplifier

PROEL suggested equipment:

HPX900 power amplifier

pub, bar,

restourant, hotels

fixed installation

system

4x FLASH5P (16 ohm)

1x SW110P (8+8 ohm)

Pamp. 300W x2 (4 ohm)

basic system

2x FLASH5P (16 ohm)

2x XENIA X80T (8 ohm)

plus

1x SW110P (8+8 ohm)

Pamp. 200W x2 (4 ohm)

+-+-

or or

FIG. 3 / 4

ACTIVE - CONTROL PANEL (FIG. 3) ATTIVO - PANNELLO DI CONTROLLO (FIG. 3)

ACTIVE - CONNECTIONS (FIG. 4) ATTIVO - CONNESSIONI (FIG. 4)

INPUT (ingresso)

Jack (bilanciato)

INPUT

Jack (balanced)

sleeve - ground

tip - hot

ring - cold

INPUT (ingresso)

XLR bilanciato maschio

INPUT

Balanced male XLR

ground

hot

cold

INPUT (ingresso)

Jack (sbilanciato)

INPUT

Jack (unbalanced)

ground

tip - hot

cold

*nota: connettere insieme cold e ground

per cavi da bilanciato a sbilanciato

*note: connect both cold and ground

to make cable from balanced to unbalanced

LINK (uscita)

XLR bilanciato femmina

LINK (output)

Balanced female XLR

ground

hot

cold

PROEL suggested

equipment:

M-series mixer

LEFT

FLASH5A

RIGHT

FLASH5A

SW110A (sub)

LEFT

2x FLASH5A

LEFT

FLASH8A

RIGHT

FLASH8A

RIGHT

2x FLASH5A

SW110A (sub)

SW110A (sub) SW110A (sub)

basic

SUB+SAT system

1x SW110A

2x FLASH5A

250W x1 + 100W x2

(450W)

double sat

SUB + 2 SAT system

1x SW110A

4x FLASH5A

250W x1 + 100W x4

(650W)

power

2 SUB + 2 SAT system

2x SW110A

2x FLASH8A

250W x2 + 230W x2

(960W)

FIG. 5

ACTIVE - CONFIGURATION EXAMPLES (FIG. 5) ATTIVO - ESEMPI DI CONFIGURAZIONE (FIG. 5)

english

SAFETY AND PRECAUTIONS

• CAUTION: Before using this product read carefully the following safety instructions. Take a look of this manual entirely and preserve it for future

reference.

When using any electric product, basic precautions should always be taken, including the following:

– To reduce the risk, close supervision is necessary when the product is used near children.

– Protect the apparatus from atmospheric agents and keep it away from water, rain and high humidity places.

– This product should be site away from heat sources such as radiators, lamps and any other device that generate heat.

– This product should be located so that its location or position does not interfere with its proper ventilation and heating dissipation.

– Care should be taken so that objects and liquids do not go inside the product.

– The product should be connected to a power supply mains line only of the type described on the operating instructions or as marked on the

product. Connect the apparatus to a power supply using only power cord included making always sure it is in good conditions.

–

WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.

– Do not cancel the safety feature assured by means of a polarized line plug (one blade wider than the other) or with a earth connection.

– Make sure that power supply mains line has a proper earth connection.

– Power supply cord should be unplugged from the outlet during strong thunderstorm or when left unused for a long period of time.

– Do not place objects on the product’s power cord or place it in a position where anyone could trip over, walk on or roll anything over it. Do not

allow the product to rest on or to be installed over power cords of any type. Improper installations of this type create the possibility of ﬁ re hazard

and/or personal injury.

– This product may be capable of producing sound levels that could cause

permanent hearing loss. Exposure to extremely high noise levels may cause

permanent hearing loss. Individuals vary considerably in susceptibility to noise-

induced hearing loss, but nearly everyone will lose some hearing if exposed to

sufﬁ ciently intense noise for a period of time. The U.S. Government’s Occupational

Safety and Health Administration (OSHA) has speciﬁ ed the permissible noise

level exposures shown in the following chart. According to OSHA, any exposure

in excess of these permissible limits could result in some hearing loss. To ensure

against potentially dangerous exposure to high sound pressure levels, it is

recommended that all persons exposed to equipment capable of producing high

sound pressure levels use hearing protectors while the equipment is in operation.

Ear plugs or protectors in the ear canals or over the ears must be worn when

operating the equipment in order to prevent permanent hearing loss if exposure

is in excess of the limits set forth here. Keep your's attention that childrens and

pets are more suscetible to excessive noise levels.

IN CASE OF FAULT

• In case of fault or maintenance this product should be inspected only by qualiﬁ ed service personnel when:

– There is a ﬂ aw either in the connections or in the supplied connecting cables.

– Liquids have spilled inside the product.

– The product has fallen and been damaged.

– The product does not appear to operate normally or exhibits a marked change in performance.

– The product has been losted liquids or gases or the enclosure is damaged.

• Do not operate on the product, it has no user-serviceable parts inside, refer servicing to an authorized maintenance centre.

TROUBLESHOOTING

No Power

(active)

• The loudspeaker's "POWER" switch is off.

• Make sure the mains AC outlet is live (check with a tester or a lamp).

• Make sure the mains plug is securely plugged into mains AC outlet.

No Sound

(active)

• Is the input LEVEL control for the channel turned up?

• Is the SIGNAL LED illuminated? If not check if your signal level is too low or check the signal cable, mixer and other

equipment setting and cabling.

• Are you sure your signal cables works properly? check it using a cable tester or replacing with a new one.

No Sound

(passive)

• Is the loudspeaker cable connected?

• Are you sure you have connected the ampliﬁ er outputs to the subwoofer keeping the polarity on both channels?

• Are you sure your power cable works properly? check it using a cable tester or replacing with a new one.

• Are you sure your power cables connected properly? you have to connect the ampliﬁ er to the suboowofer input and your

full range loudspeakers to HIGH PASS output.

A lack of bass

(active)

• With two or more subwoofer working, check the polarity switch of all subwoofers: all these switches must be in the same

position.

Distorted Sound

• Input signal level is too high. Turn down your level controls.

NOTE: The loudspeakers should never be operated at a level which causes the ampliﬁ er Clip LEDs to illuminate constantly.

Different channel

level

• Check if are using a balanced cable for one channel and an unbalanced one for the other, as this would cause a

considerable difference in channel levels.

• Be sure that your loudspeaker system is fully connected and both loudspeakers have the same impedance.

Noise / Hum

• Enable GND LIFT button on rear panel, if the problem persist press all GND LIFT buttons for all system's ampliﬁ ers.

• Whenever possible, preferably use only balanced cables. Unbalanced lines may also be used but may result in noise over

long cable runs.

• Sometimes it helps to plug all audio equipment into the same AC circuit so they share a common ground.

Duration Per Day

In Hours

Sound Level dBA

Slow Response

Typical

Example

8 90 Duo in small club

692

4 95 Subway Train

397

2 100 Very loud classical music

1.5 102

1 105 Trafﬁ c noise

0.5 110

0.25 or less 115 Loudest parts at a rock concert

english

CE CONFORMITY

• Proel products comply with directive 2004/108/EC (EMC), as stated in EN 55103-1 and EN 55103-2 standards and with directive 2006/95/CE (LVD),

as stated in EN 60065 standard.

• Under the EM disturbance, the ratio of signal-noise will be changed above 10dB.

PACKAGING, SHIPPING AND COMPLAINT

• This unit package has been submitted to ISTA 1A integrity tests. We suggest you control the unit conditions immediately after unpacking it.

• If any damage is found, immediately advise the dealer. Keep all unit packaging parts to allow inspection.

• Proel is not responsible for any damage that occurs during shipment.

• Products are sold “delivered ex warehouse” and shipment is at charge and risk of the buyer.

• Possible damages to unit should be immediately notiﬁ ed to forwarder. Each complaint for manumitted package should be done within eight days

from product receipt.

WARRANTY AND PRODUCTS RETURN

• Proel products have operating warranty and comply their speciﬁ cations, as stated by manufacturer.

• Proel warrants all materials, workmanship and proper operation of this product for a period of two years from the original date of purchase. If

any defects are found in the materials or workmanship or if the product fails to function properly during the applicable warranty period, the owner

should inform about these defects the dealer or the distributor, providing receipt or invoice of date of purchase and defect detailed description.

This warranty does not extend to damage resulting from improper installation, misuse, neglect or abuse. Proel S.p.A. will verify damage on returned

units, and when the unit has been properly used and warranty is still valid, then the unit will be replaced or repaired. Proel S.p.A. is not responsible

for any "direct damage" or "indirect damage" caused by product defectiveness.

INSTALLATION AND DISCLAIMER

• Proel products have been expressly designed for audio application, with signals in audio range (20Hz to 20kHz). Proel S.p.A. declines any liability

for damages to objects or persons caused by lacks of maintenance, modiﬁ cations, improper use, installation not applying safety instructions and

precautions and not performed at the state of the art.

• The installation of these speakers is provided for indoors, in case of use outdoors be sure that the speakers are installed correctly in a safe

location protected from wind, rain and umidity. To avoid performance deterioration of mechanical, acoustics and electrical parts is not advisable

to leave these speakers exposed outdoors for a long period of time, so we suggest a temporary installation for the limited sound events.

• The installation of these speakers is provided for ﬂ oor or by means of speciﬁ c stands able to support their weight. Therefore avoid installation on

unstable elements such as: furnitures, chairs and vibrant surfaces as stages or other speakers without appropriate ﬁ x point speciﬁ cally designed

to avoid speaker movement. Then avoid the use of inadequate supports, we suggest to use PROEL stands and accessories only.

• In case of the speakers are provided of rigging points: DO NOT SUSPEND THE SPEAKERS FROM THE HANDLES, use exclusively these rigging

points. Consult professional rigger or structural engineers prior to suspending loudspeakers from a structure not intended for that use. Always know

the

working load limit of the structure supporting the loudspeakers. Always make sure that the rigging hardware minimum rating is at least ﬁ ve times

the actual load, speakers and rigging hardware.

• In case of suspended installations of active loudspeakers where is not possible to turn on and off the speakers from their appropriate switches,

we recomend to install switches on the mains lines, for this purpose consult an expert electrician for the exact dimensioning of wiring.

• Locate the speakers as far away as possible from radio or television receivers or other sensitive equipment. These speakers have a strong

magnetic ﬁ eld which can induce hum and noise into unshielded devices that are located nearby with consequent deterioration of reception of image

and sound.

• Proel S.p.A. reserves the right to change these speciﬁ cations at any time without notice.

POWER SUPPLY AND MAINTENANCE

• Clean only with dry cloth.

• Check periodically that the slots for its proper ventilation and heating dissipation are not obstructed by dust, remove the dust using a dry brush

or a compressed air gun.

• The ampliﬁ ed loudspeakers of Proel have been designed with CLASS I construction and must be connected always to a mains socket outlet with

a proctetive earth connection (the third grounding prong).

• Before connecting the product to the mains outlet make certain that the mains line voltage matches that shown on the rear of the product, a

tolerance of up to ±10% is acceptable.

• Inside the ampliﬁ ed loudspeakers are present special safety devices such as:

 Fuse on rear panel.

 Ampliﬁ er over-heating protection.

 Protection against excessive power applied at each speaker.

•

THE REPLACEMENT OF FUSES INSIDE THE APPARATUS MUST BE MADE ONLY BY QUALIFIED PERSONNEL.

•

CHECK THE CONDITION OF THE PROTECTION FUSE, ACCESSIBLE OUTWARD, ONLY WITH THE APPARATUS SWITCHED OFF AND

DISCONNECTED FROM THE MAINS LINE OUTLET.

•

REPLACE THE PROTECTION FUSE ONLY WITH SAME TYPE AS SHOWN ON THE PRODUCT.

•

IF AFTER THE SUBSTITUTION, THE FUSE INTERRUPTS AGAIN THE APPARATUS WORKING, DO NOT TRY AGAIN THEN CONTACT THE PROEL

SERVICE CENTER.

english

GENERAL INFORMATION

Thank you for having chosen a PROEL product. The SW Series is a range of subwoofers designed by Proel to complement

full-range speakers.

Thanks to the variety of size, power and SPL, the SW sub-woofers can offer the perfect low extension solution for any

full-range speaker.

The SW110 is a low proﬁ le, very compact sub-woofer designed to be used in ultra-portable multi-way systems or in ﬁ xed

installations requiring an extended low frequency response. Despite to the small size, SW110A is capable of producing a

high output level with punchy lows and it is the ideal complement to FLASH8A or to a pair of FLASH5A. Thanks to the dual

voice coil and to the stereo crossover, the SW110P can form, together with FLASH5P and with several models from XENIA

and XEOS series, simple and cost-effective installation systems that can be powered using just one stereo ampliﬁ er.

SW110P - PASSIVE VERSION INSTRUCTIONS ( FIG. 1 / 2 )

1. INPUT LEFT channel

External ampliﬁ er power input: these are the terminals where you connect the power cable coming from your power

ampliﬁ er or powered mixer. The powered signal is ﬁ ltered by an internal passive crossover for a better coupling with

external satellite speakers. The INPUT terminals have these connections:

RED +: positive power signal (usually red wire)

BLACK -: negative power signal (usually black wire)

2. OUTPUT LEFT channel

Output of the ﬁ ltered power signal to be sent to satellite loudspeaker. The terminals has the same pin out as speciﬁ ed

above.

3. INPUT RIGHT channel

External ampliﬁ er power input: these are the terminals where you connect the power cable coming from your power

ampliﬁ er or powered mixer. The powered signal is ﬁ ltered by an internal passive crossover for a better coupling with

external satellite speakers. The INPUT terminals have these connections:

RED +: positive power signal (usually red wire)

BLACK -: negative power signal (usually black wire)

4. OUTPUT RIGHT channel

Output of the ﬁ ltered power signal to be sent to satellite loudspeaker. The terminals has the same pin out as speciﬁ ed

above.

BE CAREFUL TO THE POLARITY: it is very important that all the loudspeakers are connected with the same polarity,

otherwise improper results and damages could occur. This is particularly valid for the woofer used in the SW110,

which includes two 8 ohm voice coils that must move together in the same direction. If the polarity of one of them is

inverted compared to the other, the speaker will not move at all and after some time the coils will overheat and then they

will blow.

For checking if the input connection is correct you can do as following. Connect the ampliﬁ er to the subwoofer without

satellites. Send a low frequency signal to one channel ONLY and you will hear the signal at a certain level. Then send the

same signal also to the second channel and, if the polarity is correct, you should hear a louder signal. If the polarity (and

then the connection) is not correct, you will hear the signal level to be reduced.

PARALLEL CONNECTION: in some occasion you could want to connect the SW110P subwoofer to a single dedicated

ampliﬁ er: in this case the inputs must be connected in parallel preserving the same polarity. The ampliﬁ er must be

capable of 200-300W continuos power for a 4 ohm load (resulting from the parallel of 8 and 8 ohm).

CHOOSE THE AMPLIFIER POWER: We give you two power-handling numbers: RMS (continuous), and PEAK. So these

data suggest you can use any ampliﬁ er with a power capability equal or less the power-handling, but this rule is valid

only if the ampliﬁ er never clip anytime.

Preventing loudspeaker damage caused by clipping, that is likely the number one cause of damage, and assuming you

want to use the full capability of the loudspeaker, we recommend the use of an ampliﬁ er with a built-in limiter to prevent

clipping, in this case the rated power capability must be the same continuous power rating of the loudspeaker into the

same speciﬁ ed impedance (tipically 4 or 8 ohms):

IMPORTANT: Clipping occurs when the signal at the output of any device in the system (not just the ampliﬁ er) reaches its

maximum level. Proper operation of a sound system includes being aware of the types of audio signals being reproduced,

controlling the output levels accordingly, and operating all the devices in the system so that no clipping occurs within

the signal chain.

SW110A - ACTIVE VERSION INSTRUCTIONS ( FIG. 3 / 4 / 5 )

1. INPUT LEFT (combo XLR-JACK input)

This is a female combo connector, which accepts a XLR or a JACK plug from almost any type of equipment with a balanced

or unbalanced line level outputs. The XLR input is wired as follows:

Pin 1 = shield or ground

Pin 2 = + positive or "hot"

Pin 3 = - negative or "cold"

The JACK input is wired as follows:

Tip = + positive or "hot"

Ring = - negative or "cold"

Sleeve = shield or ground

When connecting an unbalanced signal, wire them as follows:

Pin2 / Tip = + positive or "hot"

Pin 1-3 / Sleeve = shield or ground

NOTE: Whenever possible, use always balanced cables. Unbalanced lines may also be used but may result in noise over

long cable runs. In any case, avoid using a balanced cable for one channel and an unbalanced one for the other.

2. LINK LEFT (XLR output balanced)

This is a male XLR connector, that is connected in parallel with the respective line input (so the LINK is wired as the input).

Connect these to the inputs of other powered speakers to make an array.

3. OUT LEFT (XLR output balanced)

This is a male XLR connector, that provides a balanced line-level signal. This signal is ﬁ ltered with an high-pass ﬁ lter to

connect a sat speaker. This output is wired as follows:

Pin 1 = shield or ground

Pin 2 = + positive or "hot"

Pin 3 = - negative or "cold"

4. INPUT RIGHT (combo XLR-JACK input)

Same as above. Use both inputs and outputs when connect a stereo system to a single subwoofer (1 sub + 2 sat). In the

case of mono system (1 sub + 1 sat for each channel) you can use either left or right input without distinction.

5. LINK RIGHT (XLR output balanced)

This is a male XLR connector, that is connected in parallel with the respective line input (so the LINK is wired as the input).

Connect these to the inputs of other powered speakers to make an array.

6. OUT RIGHT (XLR output balanced)

Same as above. Use both inputs and outputs when connect a stereo sytem to a single subwoofer (1 sub + 2 sat). In the

case of mono system (1 sub + 1 sat for each channel) you have to use the same channel used for input: left or right.

7. GND LIFT switch

This switch lift the ground of the balanced audio inputs from the earth-ground of the ampliﬁ er. If you have HUM noise

problem on one or more loudspeaker try to change the position of these switches (often all up or all down for all the

ampliﬁ ers in the system). Please note that to have an effect all cables must be balanced.

8. FILTER 125 / 160 Hz switch

Use this switch to set the crossover frequency at 125 Hz or 160 Hz for the internal ﬁ lter and for the OUT LEFT and RIGHT

connectors. Choose the crossover frequency by your taste or music genre.

9. LEVEL control

Rotary level control: it attenuates the level of the signal sent to the subwoofer speaker. The attenuation ranges from “0”

fully closed (the signal is completely attenuated) to “10” fully open, nominal level (the signal is not attenuated in any way,

so is fed to the internal ampliﬁ er at the same level at which it arrives on input).

10. SIGN/CLIP indicator

GREEN LED illuminates to indicate the presence of the signal at the built-in ampliﬁ er input.

RED LED illuminates when the internal ampliﬁ er's output is limited. When this LED ﬂ ashes reduce the input signal level.

11. PHASE 0° / 180° switch

This switch reverses the polarity of the subwoofer. Depending on the placement of the subwoofer relative to the full-range

sat speakers, you can get a better low-frequency response in the room if you reverse the polarity of the subwoofer’s signal.

Listen in different positions of the venue in order to try which is the best sounding setting.

NOTE: ALL SUBWOOFER SPEAKERS MUST BE HAVE THE SAME POLARITY. If you note a lack in lowest frequency range

english

using more than one subwoofer, probably you have a subwoofer inverted respect the other. Be always sure all these

switches are in same position.

12. ON indicator

GREEN LED: when lighted indicates ampliﬁ er has been turned on and AC power is available.

13. POWER switch

Speaker is "ON" when the switch is in the "I" position. Use this switch to set the speaker power to ON or OFF.

NOTE: When you shut down your equipment, turn off the speaker ﬁ rst.When powering up, turn on the speaker last.

14. AC~ socket

Here’s where you plug in your speaker’s mains supply cord. You should always use the mains cord supplied with the

speaker. Be sure your speaker is turned off before you plug the mains supply cord into an electrical outlet.

15. FUSE holder

Here is placed the mains protection fuse.

Please follow the instructions on page 10 of this manual to replace it.

16. LINE VOLTAGE selector

This selector set the AC voltage line of your country (usually it is set by factory and isn't necessary to change). The 120V

setting is for mains line in the range of 105-120V~ and 240V setting is for mains line in the range of 210-240V~.

WARNING: an incorrect setting of AC LINE VOLTAGE could damage seriuosly the internal ampliﬁ er!

17. POWER OUT AC~ socket

Here’s where you plug in your satellite speaker’s mains supply cord. Connecting the satellite speaker to this socket you

can switch on/off the whole system from the SW110A power switch.

WARNING: the maximum load for each socket is 4 amperes, the SW110A ampliﬁ er and both the power out sockets

are protected by the fuse.

english

Page is loading ...

registration

FOTOCOPIATE QUESTA PAGINA. COMPILATE E RISPEDITE IN BUSTA CHIUSA IL COUPON SOTTO RIPORTATO A:

PROEL S.P.A. - Via alla Ruenia, 37/43 - 64027 Sant’Omero (Te) - Italy

OPPURE VIA FAX AL NUMERO: +39 0861 88 78 62

O VIA E-MAIL: info@proelgroup.com

Cognome ___________________________________________________________________ Nome _________________________-________________________________

Ditta/Ente______________________________________________________________________________________________________________________________

Indirizzo _______________________________________________________________________________________________________________________________

CAP______________ Città ___________________________________________________________________________________ Prov. _________________________

Tel. _________________________________ Fax. __________________________________ E-mail ______________________________________________________

Prodotto ______________________________________________________________________________________________________________________________

Nome rivenditore _______________________________________________________________________________ Data acquisto _____________________________

Si, inseritemi nel vostro database per:

Poter ricevere depliants dei nuovi prodotti

Ricevere l’invito per le demo e la presentazione in anteprima dei nuovi prodotti

Per consenso espresso al trattamento dei dati personali a fini statistici e promozionali della vostra società, presa visione dei diritti di cui all’articolo 13 legge 675/1996.

Data ______________________________________________ Firma ______________________________________________________________________________

PHOTOCOPY THIS PAGE, COMPILE AND SEND IN A SEALED ENVELOP TO:

PROEL S.P.A. - Via alla Ruenia, 37/43 - 64027 Sant’Omero (Te) - Italy

OTHERWISE FAX TO: +39 0861 88 78 62

OR BY E-MAIL: info@proelgroup.com

Name ______________________________________________________________________ Surname _________________________-_____________________________

______

Company / Board_______________________________________________________________________________________________________________________

Address _______________________________________________________________________________________________________________________________

POST Code______________ Town _________________________________________________Province / State / Country ____________________________________

Phone _________________________ Fax. _________________________________________ E-mail ____________________________________________________

Product _______________________________________________________________________________________________________________________________