Craftsman 358798550 Owner's manual

Brand: Craftsman

Model: 358798550

Category: Grass trimmers

Type: Owner's manual

This manual is also suitable for

358.798550

Operator's Manual

CRRFTSMRN

1.46 cu. in./24cc 2-Cycle

18 Inch Cutting Path/.080 In. Line

GASOLINE WEEDWACKER ®

Model No.

358.798550

WARNING:

Read and follow all Safety Rules and Operating

Instructions before first use of this product.

For answers to your questions about this product:

Call 7 am-7 pm, Mon-Sat; Sun, 10 am-7 pm

1-800-235-5878

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

530-084028 04/2/96

WarrantyStatement 2 Storage 11

SafetyRules 2 TroubleshootingChart t2

Assembly 4

Operation 5 RepairPartsList 13

Maintenance 9 Spanish 16

Service&Adjustments 10 PartsOrdering BackCover

FULLONEYEARWARRANTYONCRAFTSMANWEEDWACKER®GAS

POWEREDLINETRIMMER.

Foroneyearfromthedateofpurchase,whenthisCraftsmanGasPowered

Weedwacker®LineTrimmerismaintained,lubricated,andtuned up according to

the operating and maintenance instructions in the Operator's Manual, Sears will

repair, free of charge, any defect in materials or workmanship.

This warranty excludes nylon line, spark plug, and air filter, which are expendable

parts and become worn during normal use.

If this Weedwacker® Line Trimmer is used for commercial purposes, this warran-

ty applies for only 90 days from the date of purchase. If this Weedwacker® Line

Trimmer is used for rental purposes, this warranty applies for only 30 days from

the date of purchase, This warranty applies onFywhile this product is in use in the

United States.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE WEEDWACKER® LINE

TRIMMER TO THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES,

This warranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

Sears, Roebuck and Co., DI817 WA Hoffman Estates, IL 60179

WARNING; When using gardening

appliances, basic safety precautions

must always be followed to reduce the

risk of fire and serious injury. Read and

follow all instructions.

This power unit can be dangerous!

Operator is responsible for following

instructions and warnings on unit and

in manual. Read entire Operator's

Manual before using unit! Be thorough-

]yfamiliar with the controls and the

proper use of the unit. Restrict the use

of this unit to persons who have read,

understand, and wilt follow the instruc-

tions and warnings on the unit and in

the manual. Never allow children to

operate this unit.

Safety information on the unit

DANGER: Never use blades or flail-

ing devices. This unit is designed for

line trimmer use only. Use of any ether

accessories or attachments will in-

crease the risk of injury.

0OO

WARNING: Trimmer line throws ob-

jects violently. You and others can be

blinded/injured. Wear eye and leg

protection.Keepbodypartsclearof

rotatingline.Keepchildren,bystand-

ers,andanimals50feet(15m)away.

Ifapproached,stopunitimmediately.

Eye Protection

• tf situations occur which are not cov-

ered in this manual, use care and

good judgement. If you need assis-

tance, contact Sears Service or call

the 1-800 number listed on the front of

this manual,

OPERATOR SAFETY

, Always wear safety eye protection.

• Always wear long pants, long

sleeves, boots, and gloves. Wearing

safety leg guards is recommended.

Do not go barefoot or wear sandals.

Stay clear of spinning line.

° Secure hair above shoulder length.

Secure or remove loose clothing or

clothing with loosely hanging ties,

straps, tassels, etc. They can be

caught in moving parts.

• Do not operate when you are tired,

ill, or under the influence of alcohol,

drugs, or medication.

• Wear hearing protection ifyou use

unitfor more than 1-1/2 hours per

day.

• Never start or run inside a closed

room or building. Breathing exhaust

fumes can kill.

• Keep handles free of oil and fuel.

UNIT / MAINTENANCE SAFETY

• Disconnect the spark plug before

performing maintenance except car-

buretor adjustments.

• Look for and replace damaged or

loose parts before each use. Look

for and repair fuel leaks before use.

Keep in good working condition.

• Replace trimmer head parts that are

chipped, cracked, broken, or dam-

aged in any other way before using

the unit.

° Make sure unit isassembled correct-

ly as shown in this manual.

• Make carburetor adjustments with

lower end supported to prevent line

from contacting any object.

• Keep others away when making car-

buretor adjustments.

• Use only recommended Craftsman

accessories and replacement parts.

FUEL SAFETY

• Mix and pour fuel outdoors,

• Keep away from sparks or flames.

* Use a container approved for fuel.

* Do not smoke or allow smoking near

fuel or the unit.

• Wipe up all fue! spills.

• Move at least 10 feet (3 meters)

away from fueling site beiore starting

engine.

* Stop engine and allow to cool before

removing fuel cap.

CUTTING SAFETY

• Use only for trimming, mowing, edg-

ing, and sweeping. Do not use for

pruning or hedge trimming.

• Inspect the area before each use.

Remove objects (rocks, broken

gtass, nails, wire, etc.) which can be

thrown by or become entangled in

line. Hard objects can damage the

trimmer .head and be thrown causing

senous injury.

• Keep firm footing and balance. Do

not overreach.

• Keep all parts of your body away

from muffler and spinning line. Keep

engine below waist level. A hot muf-

fler can cause serious burns.

, Cutting on leftside of the shield will

throw debris away from the operator.

TRANSPORTING AND STORAGE

• Allow engine to coo[;secure unit be-

fore storing or transporting in vehicle.

• Empty the fuel tank before storing or

transporting the unit. Use up fuel left

in the carburetor by starting the en-

gine and letting it run until itstops.

• Store unit and fuel in area where fuel

vapors cannot reach sparks or open

flames from water heaters, electric

motors or switches, furnaces, etc.

° Store unit so line limiter cannot acci-

dentally cause injury. The unit can be

hung by the tube.

• Store unit out of reach of children.

, If situations occur which are not cov-

ered in this manual, use care and

good judgment. If you need assis-

tance, call 1-800-235-5878.

SPECIAL NOTICE: This unit is not

equipped with a temperature limiting

muffler and spark arresting screen

which meets the requirements of Cali-

fornia Codes 4442 and 4443. All U.S.

forest land and the states of California,

Idaho, Maine, Minnesota, New Jersey,

Oregon,andWashingtonrequireby

lawthatmanyinternalcombustionen-

ginesbeequippedwithasparkarres-

torscreen.Ifyouoperateinalocale

wheresuchregulationsexist,youare

legallyresponsibleforinstallingant

maintainingtheoperatingcondition

theseparts.Failuretodosoisavic

tionofthelaw,RefertotheMAINTE.

NANCEsectioninthismanual.

CARTONCONTENTS

Checkcartoncontentsagainstthefol-

lowing]ist.

Model 358.798550

• Trimmer

• Shield with knob.

• Assist Handle with bolt and knob.

• Container of Oil

Examine parts for damage, Do not use

damaged parts.

NOTE: If you need assistance or find

parts missing or damaged, call

1-800-235-5878.

It is normal for the fuel filter to rattle in

the empty fuel tank.

Finding fuel or oil residue on muffler is

normal due to carburetor adjustments

and testing done by the manufacturer.

ASSEMBLY

WARNING: Ifreceivedassembled,

repeat all stepsto ensure your unitis

propedy assembledand all fasteners

aresecure.

ATTACHING THE HANDLE

(some units are already assembled)

WARNING: Make sure unit is prop_

assembled and all fasteners are sec_

• Assemble handle to the unit asshm

make sure bottom of handle is seal

in the groove in the trigger housin_

NOTE: Knob must be assembled or

the right hand side of the unit as

shown in the above illustration.

• Make sure the bolt is seated into tl

hex shapped here in the handle.

• Pivot handle to acomfortable positic

• Tighten handle securely.

ATTACHING SHIELD

WARNING: The shield must be pro]

edy installed. The shield provides pa_

tial protection from the risk of thrown

objects to the operator and others an

is equipped with a line limiter which

cuts excess Pineto the proper length.

The line limiter (on underside of shiel

is sharp and can cut you.

• Remove knob from shield.

• Insert bracket intoslot on shield.

• Pivot shield until bolt passes throu£

hole in bracket.

• Securely tighten knob onto bolt.

Stot

Shield___rac

ket

Wing

Nut

KNOW YOUR TRIMMER

READTHISOPERATOR'SMANUALAND SAFETYRULESBEFOREOPERATINGYOUR

UNIT.Compare the illustrations with your unit to familiarize yourself with the location of

the and adjustments. Save this manual for future reference.

p_ AssistHandle

Tube

EngineStop"" Throttle Trimmer

Swftch Trigger Head

SparkPtug

Starter

Rope Start!Run Shield

Knob \

Primer

='-'" Bulb Line

FuelMix Limiter

FitFCap Blade

ENGINE STOP SWITCH

The engine stop switch is used to stop

engine, Push and hold the engine stop

STOP or OF_O

switch in the sition until

the engine has fully stopp ,

PRIMER BULB

The primer bulb removes air from the

fuel lines and fills them with fuel. This

allows you to start the engine with few-

er pulls on the starter rope. Activate

the primer bulb by pressing it and a!-

Fowing it to return to its original form.

STARTIRUN KNOB

The START/RUNknob helps to supply

fuel to the carburetor during starting.

This allows you to start a cold engine.

Activate the START/RUNknob by mov-

ing the knob to the STARTposition. Af-

ter the engine has started, move knob

to the RUNposition.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel

information in the safety rules before

you begin. If you do not understand

the safety rules, do not attempt to fuel

your unit. Call the 1-800 number listed

on the front of this manual,

FUELING ENGINE

This engine is certified to operate on

unleaded gasoline, Before operation,

gasotine must be mixed with a good

quality 2-cycle air-cooled engine oil.

We recommend Craftsman brand oil,

Mix gasoline and oil at a ratio of 40:1

(A 40:1 ratio is obtained by mixing 3.2

ounces of oil with 1 gallon of unleaded

gasoline). DONOT USEautomotive oil

or boat oil. These oils will cause

engine damage. When mixing fuel,

follow instructions printed on container.

Once oil is added to gasoline, shake

container momentarily to assure that

the fuet isthoroughly mixed. Always

read and follow the safety rules

relating to fuel before fueling your unit.

IMPORTANT

Experience indicates that alcohol

blended fuels (called gasohol or using

ethanol or methanol) can attract mois-

ture which leads to separation and

formation of acids during storage.

Acidic gas can damage the fuel sys-

tem of an engine while in storage.

To avoid engine problems, empty fuel

system before storage for 30 days or

longer.Drain gas tank,start engine and

let it run untilfuei linesand carburetor

are empty. Use fresh fuel next season.

Never use engine or carburetor clean-

er products in the fue! tank or perma-

nent damage may occur.

See the STORAGEsection for addition-

al information.

STARTING YOUR ENGINE

Knob

Engine

Stop

Switch

HOW TO STOP YOUR UNIT

Push and hold the engine stop switch

in the STOP or OFF position until the

unit has fully stopped.

___ Knob

StartingPosition PrimerBulb

HOW TO START YOUR UNIT

WARNING: The trimmer head will

turn while starting the engine. A hot

muffler can cause serious burns.

COLD ENGINE STARTING OR

STARTING AFTER REFUELLING

• Set unit on flat surface.

• Make sure knob is in the RUNposi-

tion.

o Slowly press the primer bulb 12

times,

• Move knob to STARTposition.

• S_Squeezetdgger (fully depress and

h_9.L_,putt starter handle sharply until

engine starts. (if engine does not

staff in 3 pulls, see NOTE.)

• Continue to _r and at-

low engine to run for 5 to 10 se-

conds.

• Move the knob to the RUNposition

while continuing to squeeze trigger

for 30 second warm up.

NOTE: If engine fails to start in 3 pulls,

move knob to RUN. Squeeze trigger

and sharply pull starter handle untilen-

gine starts. Continue to squeeze trig-

ger for 30 second warm-up.

RESTARTING A WARM ENGINE

• Move knob to RUN position.

° Squeeze and hold trigger.

• Pull starter handle until engine starts.

- If engine fails to start in 3 pulls, follow

instructionsinCOLDENGINESTARTING.

STARTING AT TEMPERATURES

BELOW 40 ° F.

* FollowCOLD ENGINESTARTINGexcept

after moving knob to the STARTposition,

slowly move knob back to RUN position

and then back to STARTposition. Con-

tinueto follow COLD ENGINESTARTING.

If the unit still doesn't start, refer to

TROUBLESHOOTINGchart or call the

1-800 number listed on the front of

this manual.

OPERATING INSTRUCTIONS

OPERATING POSITION

ALWAYS WEAR: _ Eye Protection

Long Pants

Heavy Shoes

Cut from your right your left.

Do not run the engine at a higher speed

than necessary. The cutting line wilt cut

efficiently when the engine is run at less

than full throttle. At lower speeds, there

is less engine noise and vibration. The

cutting line will last longer and will be

less likelyto "welc£ onto the spool,

Always release the throttle trigger and

allow the engine to return to idle speed

when not cuffing.

To stop engine:

° Release the throttle trigger.

° Push and hold the engine stop

switch in the STOP or OFF position

until the engine has fully stopped.

TWIST-N-EDGE

• Pull the tab toward the engine.

• Twist the tube to the edging position;

release tab.

TRIMMER LINE ADVANCE

Trimmer line will advance approxi-

mately 2 in. (5 cm) each time bottom of

trimmer head is tapped on the ground

with engine running at full throttle.

The mostefficientI_nelengthis the

maximum lengthallowed by line limiter.

Alwayskeeptheshieldinplacewhen

thetoolisbeingoperated.

ToAdvanceLine:

• Operatetheengineatfullthrottle.

• Holdthetrimmerheadparalleltoand

abovethegrassyarea.

•Tapthebottomofthetrimmerhead

lightlyonthegroundonetime.Ap-

proximately2in.(5cm)oflinewillbe

advancedwitheachtap.

To advance line, tap bottom of trimmer

head on ground one time.

Line fimiter cuts line

proper length.

Always tap the trimmer head on a

grassy area. Tapping on surfaces such

as concrete or asphalt can cause ex-

cessive wear to the trimmer head.

Ifline is worn dov_ to 2 in, (5 cm) or

less, more than one tap will be required

to obtain the most efficient line length.

WARNING: Use only .080" (2 ram)

diameter line. Other sizes of line wil!

not advance properly and can cause

serious injury'. Do not use other materi-

als such as wire, string, rope, etc, Wire

can break off during cutting and be-

come a dangerous missile that can

cause serious injury.

CUTTING METHODS

WARNING: Use minimum speed and

do not crowd the line when cutting

around hard objects (rock, gravel,

fence posts, etc.), which can damage

the trimmer head, become entangled

in the fine, or be thrown causing a seri-

ous hazard.

• The tip of the line does the cutting.

You will achieve the best perform-

ance and minimum line wear by not

crowding the line into the cutting

area. The right and wrong ways are

shown below.

Tipof the Line I Line Crowded Into

DoesThe Cutting I WorkArea

Right " _a_t Wrong " "'

• The fine will easily remove grass and

weeds from around walls, fences,

trees and flower beds, but it also can

cut the tender bark of trees or shrubs

and scar fences. To help avoid dam-

age especially to delicate vegetation

or trees with tender bark, shorten line

to 4--5 in. (10-13 cm) and use at less

than full throttle,

• For trimming or scalping, use less

than full throttle to increase fine life

and decrease head wear, especially:

• During light duty cutting.

• Near objects around which the line

can wrap such as small posts,

trees or fence wire.

• For mowing or sweeping, use full

throttle for a good clean job.

WARNING: Always wear eye protec-

tion. Never tean over the trimmer head.

Rocks or debris can ricochet or be

thrown into eyes and face and cause

blindness or other serious injury.

TRIMMING - Hold the bottom of the

trimmer head about 3 in. (8 cm) above

the ground and at an angle. Allow only

the tip of the line to make contact. Do

not force trimmer tine into work area.

Trimming

AboveGround _ '_ _/_.

SCALPING - The scalping technique

removes unwanted vegetation. Hold

the bottom of the trimmer head about 3

in. (8 cm) above the ground and at an

angle. Allow the tip of the line to strike

the ground around trees, posts, monu-

ments, etc. This technique increases

line wear.

Scalping ............. ,

,._

MOWING - Your trimmer isideal for

mowing in places conventional lawn

mowers cannot reach, in the mowing

position, keep the line parallel to the

ground. Avoid pressing the head into

the ground as this can scalp the

ground and damage the tool.

SWEEPING - The fanning action of

rotating line can be used for a quick

and easy clean up. Keep line parallei

to and above the surfaces being swept

and move the tool from side to side.

EDGING - The Twist-N-Edge feature

allows for easy edging of sidewalks,

patios, driveways, etc. Adjust trimmer

to the edging position. Allow only the

tip of the line to make contact. Do not

force trimmer line into work area.

Edging __,_,,_,

MAINTENANCE SCHEDULE

CARE & MAINTENANCE TASK

Check for Loose fasteners and parts

Check for damaged or worn parts

Clean unit and labels

Clean air filter

R_ce spark ptug.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cov-

er items that have been subjected to

operator abuse or negligence. To re-

ceive full value from the warranty, the

operator must maintain unit as instruct-

ed inthis manual. Various adjustments

will need to be made periodically to

properly maintain your unit.

WHEN TO PERFORM

Before each use

After each use

Every 5 hours of operation

Yearly

fire hazard or producing harmful evap-

orative emissions,

Cleaning the air filter:

A dirty air filter decreases engine per-

formance and increases fuel consump-

tion and harmful emissions. Always

ctean after every 5 hours of operation.

• Clean the cover and the area around

CHECK FOR LOOSE

FASTENERS AND PARTS

• Spark Plug Boot

• Air Filter

• Housing Screws

• Assist Handle Screws

• Shield

it to keep dirt and debris from failing

intothe carburetor chamber when

the cover is removed.

• Remove parts as illustrated.

• Wash the filter in soap and water.

• Allow filter to dry.

• Replace parts,

CHECK FOR DAMAGED OR

WORN PARTS

Refer replacement of damaged/worn

parts to your Sears Service Center.

• Engine Stop Switch - Ensure switch

functions properly by holdingthe

switch in the "Stop" position. Make

sure engine stops; then restart en-

gine and continue.

• Fuel Tank- Do not use unit iffuel tank

shows signs of damage or leaks.

° Shield - Discontinue use of unit if

debris shield is damaged.

CLEAN UNIT & LABELS

• Clean the unit using a damp cloth

with a mild detergent.

• Wipe off unit with a clean dry cloth.

CLEAN AIR FILTER

Do not clean filter in gasoline or other

flammable solvent to avoid creating a

SFilter

Cover

REPLACE SPARK PLUG

Replace the spark plug each year to

ensure the engine starts easier and

runs better. Set spark plug gap at

.025 in. Ignition timing is fixed and

nonadjustable.

* Twist, then pull off spark plug boot.

° Remove spark plug from cylinder

and discard.

• Replace with Champion RCJ-8Y

spark plug and tighten with a 3/4 in.

socket wrench (10-12 ft.-Ibs).

° Reinstall the spark plug boot,

ADVANCING THE CUTTING LINE

Advance line by tapping bottom of cut-

ting head lightly on the ground while

engine is running at full speed. A metal

blade attached to the shield will cut the

line to the proper length.

REPLACING THE LINE

• Remove the spool by firmly pulling

on the tap button.

• Clean entire surface of hub and

spool.

• Replace with a pre-wound spool, or

cut a length of 20 feet of .080" (2

mm) diameter Craffsmane brand

line. Never use wire, rope, string,

etc., which can break off and be-

come a dangerous missile.

° insert one end of the line about 1/2

inch (1 cm) into the small hole inside

the spool.

• Wind the line evenly and tightly onto

the spool. Wind in the direction of the

arrow found on the spool.

• Push the line into the notch, leaving

3 to 5 inches (7 - I2 cm) unwound.

• Insert the line into the exit hole in the

hub as shown in the illustration.

• Align the notch with the line exit hole.

• Push the spool into the hub until it

snaps into place.

• Pull the line extending outside the

hub to release it from the notch.

Small _-z_.

Spool

Line in _ _

Line exithole

CARBURETOR ADJUSTMENT

WARNING: The trimmer head will be

spinning during most of this procedure.

Wear your protective equipment and

observe all safety precautions. After

making mixture adjustments, recheck

idle speed.

Carburetor adiustment is critical and if

done improperly can permanently

damage the engine as well as the car-

buretor. If you require further assis-

tance or are unsure about performing

this procedure, call our customer as-

sistance help line at 1-800-235-5878.

Old fuel, a dirty air filter,a dirty fuel fil-

ter, or flooding may give the impres-

sion of an improperly adjusted carbu-

retor. Check these conditions before

adjusting the carburetor.

The carburetor has been carefully set

at the factory. Adjustments may be

necessary if you notice any of the fol-

lowing conditions:

• Engine will not idle. See "Idle Speed"

under adjusting procedure.

• Engine dies or hesitates instead of

accelerating. See "Acceleration

Check" under adjusting procedure.

• Loss of cutting power. See "Mixture

Adjustment" under adjusting

procedure,

There are two adjustment screws on

the carburetor. They are located in the

area just above the primer bulb,

MixtureScrew (with -- l

Limiter Cap)

Idle

Speed

Screw

Air Filter

Cover

CARBURETOR PRESETS

When making carburetor preset adjust-

ments, do not force plastic limiter caps

beyond stops or damage may occur.

If carburetor presets are not needed,

proceed to "Adjusting Procedure, Idle

Speed."

To adjust presets:

• Turn mixture screw counterclockwise

until it stops.

° Turn the idle speed screw clockwise

until it stops. Now turn counterclock-

wise 4-1/2 turns.

• Start motor, cut grass for 3 minutes,

and proceed to the adjustment

section. If engine does not start,

refertotroubleshootingchartorca!l

the1-800numberlistedonthefront

ofthismanual.

• Ifengineperformanceisacceptable

atthepresetpositions,nofurther

adjustmentisnecessary.

ADJUSTINGPROCEDURE

Idle Speed

Allow engine to idle. Adjust speed until

engine runs without stalling.

• Turn clockwise to increase engine

speed if engine stalls or dies.

• Turn counterclockwise to decrease

speed.

No further adjustments are necessary

if performance is satisfactory.

Mixture Adjustment

DO NOT operate engine at full throttle

for prolonged periods while making ad-

justments. Damage to the engine can

occur. Extend line to the length allow

by the line limiter and cut some grass.

Based on performance whi_e cutting,

turn the mixture adjustment in

1/16-tu rn increments as follows:

• Clockwise until the engine has good

power while cutting with no hesita-

tion.

Do not adjust by sound or speed, but

judge by how welt the engine per-

forms while cutting.

• Counterclockwise if the engine has

speed but dies or lacks power while

cutting.

After completing adjustments, check

for acceleration. Reset if necessary.

Acceleration Check

If engine dies or hesitates instead of

accelerating, turn mixture adjustment

counterclockwise until you have

smooth acceleration. Recheck and ad-

just as necessary for acceptable per-

formance.

Prepare unit for storage at end of sea-

son or if it will not be used for 30 days

or more.

WARNING:

• Allow engine to cool, and secure the

unit before storing or transporting.

° Store unit and fuel in a well venti-

lated area where fuel vapors cannot

reach sparks or open flames from

water heaters, electric motors or

switches, furnaces, etc.

• Store unit with all guards in place.

Position unit so that any sharp object

cannot accidentally cause injury.

• Store unit and fuel well out of the

reach of children.

EXTERNAL SURFACES

If your unit is to be stored for a period

of time, clean it thoroughly before stor-

age. Store in a clean dry area.

- Lightly oil external metal surfaces.

FUEL SYSTEM

Under Fueling Engine in the Operating

Section of this manual, see message

labeled IMPORTANT regarding the use

of gasoho! in your engine.

Fuel stabilizer is an acceptable alter-

native in minimizing the formation of

fuel gum deposits during storage. Add

stabilizer to the gasoline in the fue!

tank or fuel storage container. Follow

the mix instructions found on stabilizer

container. Run engine at least 5 min-

utes after adding stabilizer.

CRAFTSMAN 40:1, 2-cycle engine oil

(air cooled) is already blended with

fue! stabilizer. If you do not use this

Sears oi!, you can add a fuel stabi!izer

to your fuel tank.

INTERNAL ENGINE

• Remove spark plug and pour 1 tea-

spoon of 40:1, 2-cycle engine oil (air

cooled) through the spark plug open-

ing. Slowly pull the starter rope 8 to

10 times to distribute olt.

• Replace spark plug with new one of

recommended type and heat range.

• Clean air filter.

• Check entire unit for loose screws,

nuts, and bolts. Replace any dam-

aged, broken, or worn parts.

° At the beginning of the next season,

use only fresh fuel having the proper

gasoline to oil ratio.

OTHER

• Do not store gasoline from one sea-

son to another.

• Replacegasolinecanifitstartstorust.

TROUBLESHOOTING CHART

Engine will not

start.

Engine will not

idle properly.

Engine wilt not

accelerate,

lacks power,

or dies under

a load.

Engine smokes

excessively,

Engine runs hot.

CAUSE

: Engine flooded.

Fuel tank empty,

° Spark plug not firing.

° Fuel not reaching

carburetor.

• Compression low.

• idle speed set too low.

° Idle speed set too high.

• Carburetor requires

adjustment.

° Crankshaft seals worn.

• Compression low.

° Air filter dirty.

• Spark plug fouled.

• Carburetor requires

adjustment.

• Carbon build up,

° Compression low.

• Choke partially on,

• Fuel mixture incorrect.

• Air filter dirty.

• Carburetor requires

adjustment.

. See "Starting instructions,"

° Fill tank with correct fuel mixture,

° Install new spark plug.

° Check for dirty fuet filter; replace.

Check for kinked or split fue! line

repair or replace.

° Contact Sears Service.

• Adjust idle speed screw

clockwise to increase speed.

° Adjust idle speed screw counter-

clockwise to reduce speed.

• See "Carburetor Adjustments."

• Contact Sears Service.

° Contact Sears Service.

: Clean or replace air filter.

Clean or replace spark plug

and re-gap.

• See "Carburetor Adjustments?

* Contact Sears Service.

. Contact Sears Service.

° Adjust ch0kel .......

° Empty fuel tank and refill with

correct fuel mixture.

° Clean or replace air fUter,

° See "Carburetor Adjustments."

• Fuel mixture incorrect. ° See "Fueling Your Unit."

• Spark plug incorrect. ° Replace with correct spark plug.

• Carburetor requires i* See "Carburetor Adjustments."

adjustment

• Carbon build up. • Contact Sears Service,

REPAIR PARTS

Ref.

10,

11,

12,

13,

"M.

15.

14, --

Part No.

53O-O94551

530-016179

530-049107

530-047923

530-047924

530-O47910

530,,.015820

530-042084

530,K)47925

530,_015810

530-O49O65

530-095249

530-015814

530-069666

[_scdption

Drive Shaft

Screw-Throttte Hsg.

Tdgger

Throttie Hsg. (Right)

Tnrottle Hsg. (Left)

Assist Handle

Bolt-Sh_e_d

Spring-Compression

Actuator

Screw

Drive Shaft Hsg, Ass'y

Line Lim_te_

Screw._Line Limlter

Shield Kit Ass'y.

Rel, Part No,

16. 530-095380

17. 530-401958

18. 530*401957

19. 71-85816

20. 530-O47912

21. 530-047911

22. 530-016173

23. 530_16119

24. 530=094543

25. 530_0t6193

Not Sho_

Descdption

Hub Ass'y

Spriag

Clip-RetaineP-Head

Spool w/Line

Locatot-right

Locstor-left

8oft-Handle

K_ob-Handle

Oust Cup

Washe_

952-701676

(Ind, t2 & 13)

Cutting Head ASS'y,

(IncL t6-19)

53O-O84O28

530_049101

530-049104

530-049_06

Operator's Manual

Shaft Warning Decat

Shield Decal

Starting Instruction

REPAIR PARTS

Ref,

10.

11.

12.

13,

14,

15.

!6.

17.

18.i

19,

20,

21,

22.

23,

24.

25.

26.

27,

Part No,

530-016164

530_ 15892J

530-01616_

530-01588C

530-02756_

530-01581(;

530-019233

Champion

530-0"_9194

530-015945

530-049390

530-049389

530-039149

530-039163

530-036145

530-015954

530-015828

530--027953

530-014532

530,-069615

530-047737

530-014851

530-032125:

530.-03212_

530--01917_

530--015941

530-03657_

Descdptlon Ref,

Starter Spring 28,

Screw 29.

Retainer-Pulley 30,

Screw 31,

Starter Handle 32.

Screw 33.

Ga sket,.,CylindedCa rb. 34.

Spark Plug (RCJ--eY) 35,

Gasket-Carb, 36.

Retainer Ring--C'case 37,

Lead Wire 38.

Ground W{re

Ft_jwheel 39,

Ignition Module 40.

Spacer-Ignit. Module 41.

SCrew-_gnit. Mod_e 42.

Washer-Thrust 43. ;

Drive Coupling 44. :

Crankshaft Ass'y. 45,

Connecting Rod Assy, 46,

Piston Ring 47.

Crankcase Assy. 48.

(inci, lO & 23-26) 49,

Inner Bearing 50,

Outer 8earlng 51,

C'case SeaI 52,

Ret, Ring/C'shafI 53,

Mufflet Body

Part No,

530-,,036577

53O-O38602

;530-_036579

530-029930

530-049377

530-019181

530-069757

530-069758

530-016014

530-019223

530--069755

530-015882:

530-047914

530-047917

530-047915

530.-0_5254

530-015852

530-049089

530-047932

530-047913

530-015966

530-049066

530-049299

530-'015953

530-,'036793

530_069247

Oescdptfon

Muffler Cover

Muffler Baffle-Exit

Muffler Baffte.-,First

Muffler Spring

Rear Shtodd

Gasket.-,C'case

Cyl_nc_er Kit

Carb. Adaptor Kit

Screw,_-Carb Adptr,

Gasket,,_Cylinder

Carburetor Assy Kit

(tnel. Limlter Cap)

Screw--Flywheel

Choke Prate

Choke Knob

Choke Lever

Wave Washe_

Choke Spacer

Air Box

A_tFitler Foam

Air Fitter COver

Screw-Air Bex

Threttte Cebte Assy

Fuel Tank Ass'y.

Screw'._Cylinder

Shroud IsOta!Or

Fuel Line-,,Oarbf'rank

Ref, Pa_ No,

i54. 530_069660

i55, 530-014347

i56, 530-014352

i57, 530-069625

158. 530--01472g

59, 530'-038!14

60, 530-069762

61, 530-069232

62, 530._)69400

63, 530--069599

64. 530-0160801

65. 530-036792

66. 530--015557

67. 530+_069380

68. 530-015162

69. 530_069756

70, !530-=016191

71, 530-=049284

Description

Muffler Kit

(Inol.27,-31)

Fuet Cap Ass,/,

Fuet Pickup Assy

Engine Gasket Kit

(lncl, 7.9,33, 37)

C'ease/C'shaft Assy,.

(Incl. 10.19.22-26)

•On/Off Switch

Fan Housing Assy,

Rol:_eKit

Starter Pulley Kit

(Insl, 64)

Fuel Line-Carbfrank

Screw

lsolator,..,C'case

Screw

Spark ArteSlOr Kil

Piston Pin Retainer

Piston Kit

(incl. 2!,68 & Pin)

r Spring Starter Dog

Starter Dog

Page is loading ...

For the repair or replacement parts you need

delivered directly to your home

Call 7 am - 7 pm, 7 days a week

1-800-366-PART

(1-800-366-7278)

Para ordenar piezas con entrega a

domicilio - 1-800-659-7084

For in-house major brand repair service

Call 24 hours a day, 7 days a week

1-800-4-REPAIR

(1-800-473-7247)

Para pedir servicio de reparaci6n a

domicilio - 1-800-676-5811

For the location of a Sears Parts and

Repair Center in your area

Call 24 hours a day, 7 days a week

1-800-488-1222

mmmmmm

mmmmmm mm

For information on purchasing a Sears

Maintenance Agreement or to inquire

about an existing Agreement

Call 9 am - 5 pm, Monday-Saturday

1-81)0-827-6655

When requesting service or ordering

_: parts, always provide the following

information:

i_ • Product Type ° Part Number

:? ° Model Number • Part Description

S£ 8

America's Repair Specialists

Craftsman 358798550 Owner's manual

Brand: Craftsman

Model: 358798550

Category: Grass trimmers

Type: Owner's manual

This manual is also suitable for

358.798550

Download PDF

report

in other languages

español: Craftsman 358798550 El manual del propietario

Craftsman 358798550 Owner's manual

This manual is also suitable for

Craftsman 358798550 Owner's manual

in other languages

Related papers

Other documents