Insignia NS-UKF8001AXX-2 Quick setup guide

Insignia
Brand
Insignia
Model
NS-UKF8001AXX-2
Type
Quick setup guide

This manual is also suitable for

Insignia NS-UKF8001AXX-1/ NS-UKF8001AXX-2 Refrigerator Filter effectively enhances your drinking water by reducing chlorine, taste, and odor, NSF certified. Simple to install, it fits snugly into your refrigerator, requiring only a 15-minute pre-soak and a few twists. For optimal performance, replace every 3 to 6 months to prevent bacteria and fungus growth.

Insignia NS-UKF8001AXX-1/ NS-UKF8001AXX-2 Refrigerator Filter effectively enhances your drinking water by reducing chlorine, taste, and odor, NSF certified. Simple to install, it fits snugly into your refrigerator, requiring only a 15-minute pre-soak and a few twists. For optimal performance, replace every 3 to 6 months to prevent bacteria and fungus growth.

INSTALLING THE WATER FILTER
Note: It is normal to have black carbon particles on the outside of your lter. They are
safe and can be wiped o.
1 You must soak your new lter in water for 15 minutes prior to
installing it in your refrigerator to remove air from the carbon block.
2 Unlatch the plastic lter cover on the refrigerator and let it swing down.
3 Rotate the old lter 1/4 turn counterclockwise, then pull it straight out.
4 Push the new lter into the refrigerator until it stops, then rotate it
1/4 turn clockwise.
Note: Filter connections are larger to prevent leaks. You may need to twist the lter
hard to make sure that the connection is secure.
5 Swing the plastic lter cover up until it snaps closed.
6 Reset your refrigerator’s “change lter” light (if it has one). See “Resetting
your change lter indicator” for more information.
7 Run 2-3 gallons of water through your refrigerator to remove air and loose
carbon pieces.
RESETTING YOUR CHANGE FILTER INDICATOR
Note: These are the most common lter reset instructions. See the documentation
that came with your refrigerator if they don’t work.
Before using your new product, please read these instructions to prevent any damage.
PACKAGE CONTENTS
• Refrigerator lter(s) (1 or 2 pack)
• Quick Setup Guide
REFRIGERATOR BRAND
Amana®
Kenmore
Maytag® and Jenn-Air®
INSTRUCTIONS
• Press and hold the dispenser lock and auto light buttons at the
same time until the lter indicator ashes (about four seconds).
OR
• Press and hold the dispenser lock and water buttons at the same
time until the lter indicator ashes (about four seconds).
• The lter reset for Kenmore refrigerators varies by model. See
the documentation that came with your refrigerator.
• Press and hold the lock and light buttons at the same time
until the lter indicator ashes (about four seconds).
OR
• On newer models, press and hold the lock and water buttons at
the same time until the lter indicator ashes (about four seconds).
QUICK SETUP GUIDE
Refrigerator Filter
NSUKF8001AXX1 / NSUKF8001AXX2
TROUBLESHOOTING STORAGE AND MAINTENANCE
• Replace your lter every three to six months to prevent bacteria and
fungus growth in your lter, supply lines, and storage tank.
• Stored lters do not expire. Keep your unused lters in a cool, dark, and
dry place until you need them.
• If you do not use your water dispenser for more than four days, run two
gallons of water before using it to prevent bad tasting water.
ONEYEAR LIMITED WARRANTY
For complete warranty, visit www.insigniaproducts.com.
CONTACT INSIGNIA
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
CERTIFICATIONS:
INSIGNIA is a trademark of Best Buy and its aliated companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2018 Best Buy. All rights reserved.
Made in China
V2 ENGLISH 18-0538
PROBLEM
My refrigerator is not
dispensing water
My water dispenser is
dripping
My water is cloudy or
contains black carbon
pieces
My new lter is making
noises or sputtering
My water tastes bad
SOLUTION
• Make sure that you soaked your lter in water
for 15 minutes before installing.
• Make sure that the lter is securely connected
to the receiver. Do not use tools to tighten the
lter in place.
• Make sure that the water line to the refrigerator
is turned on. The valve must be completely
open for the refrigerator to receive water.
• Make sure that the refrigerator door is closed or
the dispenser will not work.
• A few drops are normal. If the water is dripping
constantly, have a service technician check your
refrigerator’s water valve.
• Cloudy water is caused by microscopic air
bubbles. Run two to three gallons of water from
your dispenser to clear the air bubbles out.
• Black carbon pieces in the water are normal and
appear with all carbon lters. Run two to three
gallons of water through your dispenser to
remove loose carbon pieces.
• Make sure that you soaked your lter in water
for 15 minutes before installing.
• Noises and sputtering are caused by trapped air
pockets. Run two to three gallons of water from
your dispenser to push the air out.
• If you do not use your water dispenser for more
than four days, run two gallons of water
through the dispenser before using it.
• Make sure that you replace your lter every
three to six months to prevent bacteria growth.
Tested and Certied by NSF International in Model
EFF-6007S against NSF/ANSI Standard 42 for the
reduction of chlorine, taste and odor.
REPLACEMENT
ELEMENT
  • Page 1 1
  • Page 2 2

Insignia NS-UKF8001AXX-2 Quick setup guide

Insignia
Brand
Insignia
Model
NS-UKF8001AXX-2
Type
Quick setup guide
This manual is also suitable for

Insignia NS-UKF8001AXX-1/ NS-UKF8001AXX-2 Refrigerator Filter effectively enhances your drinking water by reducing chlorine, taste, and odor, NSF certified. Simple to install, it fits snugly into your refrigerator, requiring only a 15-minute pre-soak and a few twists. For optimal performance, replace every 3 to 6 months to prevent bacteria and fungus growth.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents