Insignia NS-UKF8001AXX-1 Quick setup guide

Brand: Insignia

Model: NS-UKF8001AXX-1

Type: Quick setup guide

This manual is also suitable for

Insignia NS-UKF8001AXX-1/ NS-UKF8001AXX-2 Refrigerator Filter effectively enhances your drinking water by reducing chlorine, taste, and odor, NSF certified. Simple to install, it fits snugly into your refrigerator, requiring only a 15-minute pre-soak and a few twists. For optimal performance, replace every 3 to 6 months to prevent bacteria and fungus growth.

INSTALLING THE WATER FILTER

Note: It is normal to have black carbon particles on the outside of your lter. They are

safe and can be wiped o.

1 You must soak your new lter in water for 15 minutes prior to

installing it in your refrigerator to remove air from the carbon block.

2 Unlatch the plastic lter cover on the refrigerator and let it swing down.

3 Rotate the old lter 1/4 turn counterclockwise, then pull it straight out.

4 Push the new lter into the refrigerator until it stops, then rotate it

1/4 turn clockwise.

Note: Filter connections are larger to prevent leaks. You may need to twist the lter

hard to make sure that the connection is secure.

5 Swing the plastic lter cover up until it snaps closed.

6 Reset your refrigerator’s “change lter” light (if it has one). See “Resetting

your change lter indicator” for more information.

7 Run 2-3 gallons of water through your refrigerator to remove air and loose

carbon pieces.

RESETTING YOUR CHANGE FILTER INDICATOR

Note: These are the most common lter reset instructions. See the documentation

that came with your refrigerator if they don’t work.

Before using your new product, please read these instructions to prevent any damage.

PACKAGE CONTENTS

• Refrigerator lter(s) (1 or 2 pack)

• Quick Setup Guide

REFRIGERATOR BRAND

Amana®

Kenmore

Maytag® and Jenn-Air®

INSTRUCTIONS

• Press and hold the dispenser lock and auto light buttons at the

same time until the lter indicator ashes (about four seconds).

• Press and hold the dispenser lock and water buttons at the same

time until the lter indicator ashes (about four seconds).

• The lter reset for Kenmore refrigerators varies by model. See

the documentation that came with your refrigerator.

• Press and hold the lock and light buttons at the same time

until the lter indicator ashes (about four seconds).

• On newer models, press and hold the lock and water buttons at

the same time until the lter indicator ashes (about four seconds).

QUICK SETUP GUIDE

Refrigerator Filter

NSUKF8001AXX1 / NSUKF8001AXX2

TROUBLESHOOTING STORAGE AND MAINTENANCE

• Replace your lter every three to six months to prevent bacteria and

fungus growth in your lter, supply lines, and storage tank.

• Stored lters do not expire. Keep your unused lters in a cool, dark, and

dry place until you need them.

• If you do not use your water dispenser for more than four days, run two

gallons of water before using it to prevent bad tasting water.

ONEYEAR LIMITED WARRANTY

For complete warranty, visit www.insigniaproducts.com.

CONTACT INSIGNIA

1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)

www.insigniaproducts.com

CERTIFICATIONS:

INSIGNIA is a trademark of Best Buy and its aliated companies.

Distributed by Best Buy Purchasing, LLC

7601 Penn Ave South, Richeld, MN 55423 U.S.A.

Made in China

V2 ENGLISH 18-0538

PROBLEM

My refrigerator is not

dispensing water

My water dispenser is

dripping

My water is cloudy or

contains black carbon

pieces

My new lter is making

noises or sputtering

My water tastes bad

SOLUTION

• Make sure that you soaked your lter in water

for 15 minutes before installing.

• Make sure that the lter is securely connected

to the receiver. Do not use tools to tighten the

lter in place.

• Make sure that the water line to the refrigerator

is turned on. The valve must be completely

open for the refrigerator to receive water.

• Make sure that the refrigerator door is closed or

the dispenser will not work.

• A few drops are normal. If the water is dripping

constantly, have a service technician check your

refrigerator’s water valve.

• Cloudy water is caused by microscopic air

bubbles. Run two to three gallons of water from

your dispenser to clear the air bubbles out.

• Black carbon pieces in the water are normal and

appear with all carbon lters. Run two to three

gallons of water through your dispenser to

remove loose carbon pieces.

• Make sure that you soaked your lter in water

for 15 minutes before installing.

• Noises and sputtering are caused by trapped air

pockets. Run two to three gallons of water from

your dispenser to push the air out.

• If you do not use your water dispenser for more

than four days, run two gallons of water

through the dispenser before using it.

• Make sure that you replace your lter every

three to six months to prevent bacteria growth.

Tested and Certied by NSF International in Model

EFF-6007S against NSF/ANSI Standard 42 for the

reduction of chlorine, taste and odor.

REPLACEMENT

ELEMENT

Insignia NS-UKF8001AXX-1 Quick setup guide

Brand: Insignia

Model: NS-UKF8001AXX-1

Type: Quick setup guide

This manual is also suitable for

Download PDF

report

Insignia NS-UKF8001AXX-1 Quick setup guide

This manual is also suitable for

Insignia NS-UKF8001AXX-1 Quick setup guide

Related papers

Other documents