7.2 Inch Rear View Mirror Monitor
with Full Display Screen
USER MANUAL
Serial No.: 2019FK073A4WT231231
Rear-view mirror is not powered.Q:
Make sure that ACC, B+, GND are well connected, and that the lter box's fuse is not burnt out.A:
The video displayed on the screen is overlapped by the rolling shadow of another video. Q:
Make sure that the video extension interface is in good condition. If this still exists, it is recommended to use
a video extension cable with a shielding layer, as shown in the following picture.
A:
NG
OK
FAQ
No entertainment video is permitted when driving except the demo for navigation and backup camera
display!
This manual is only for your reference, please check the actual product as the standard!
CAMERA
9002-7692v2 LCD Display Mirror
CONTENTS
The package contains the following:
01 Rearview mirror monitor
02 User manual
03 Wire cover
04 Wire control
05 Remote control
06 Wire harness
06
01
FEATURES
SPECIFICATIONS
Screen size: 7.2 inch
Aspect resolution: 1280(H)*390(V)
Signal system: PAL/Auto/NTSC
Display screen: TFT-LCD
7.2 inch wide LCD display screen
4 analog video inputs
Back-up camera display
Adjustable Back up guide lines
Automatic brightness adjustment
Channel switch among VIDEO, RTIGHT, LEFT, CAMERA
HOW TO INSTALL REVERSE CAMERA
When a camera needs to be installed at the rear of vehicle, a good position is usually at the top of the License plate
where there is an under ledge.
1BAM 2XX
B
AM 2X
License plate
Camera
Rear view mirror monitor
Trigger wires for reverse/ left/ right Touch screen button
Working voltage: DC 10V-DC 16V
Working temperature: -20
0
C~+65
0
C
1
03
02
04
05
For the items listed above, please check your packing contents. If any damage, please contact the distributor
or the agent as soon as possible.
2
3
RIGHT, LEFT, and CAMERA
34 53 4
HOW TO INSTALL MIRROR MONITOR
Remove the original mirror
Car factory original mirror The plate on the windshield
CAUTION!
NOTE: Always use caution, DO NOT force the mount. We will not be responsible for broken windshields. If you
are not sure how to remove or re-install the mirror seek trained, qualified help.
Dangerous
Ok
Windshield
Windshield
Dangerous
Ok
1.
2.
Different cars have different brackets. It depends
on your vehicle maker and manufacturer.There are
many methods to remove the original rear view
mirror, however, please don’t force the mirror off
the bracket.
The manufacturer will not be responsible for
damage caused to your car by wrong installation of
the mirror.
Install mirror monitor on the plate
Install rear view mirror along this directionTake down your original mirror, and make
the mirror monitor ready
windshield
Please make sure to install the mirror to
the end of the bottom without any loose
Contrarotate the xed rear view mirror
Torque is about 0.8-1.3 N.m
windshield
windshield
5 6
How to install wire harness, wire cover, cable cover and connector cable on the mirror?
HOW TO WIRE
Black to GND
Red to ignition +12V
to left camera
to right camera
to front camera
to back up camera
trigger line 2 for right
trigger line 1 for left
Green to back car singal
Wire control
NOTE: The picture may not
be in line with this type of
mirror, just to demonstrate
the installation method.
When the car is in reverse, the monitor will automatically display back up camera.
The brightness of screen varies with ambient light, thereby, to make driver get a clear and comfortable image when
reversing.
When ambient light is weak, the screen will automatically reduce the brightness and get better vision.
When ambient light is strong, the screen will automatically increase the brightness and get better
vision.
WEAK LIGHT
STRONG LIGHT
BACK UP CAMERA DISPLAY
AUTOMATIC BRIGHTNESS ADJUSTMENT
BUTTONS OPERATION
Non-trigger state: Shortcut key for “CAMERA” channel switch
Non-trigger state: Switch among different video channels
1
2
3
4
1
2
34
Turn on/off the display screen
R
CH
Non-trigger state: Color mode adjustment
7 8
About “WIRE CTR DELAY”
This function is used with wire control switch.
1. If "WIRE CTR DELAY" is set "OFF", this function is same as the touch button "CH" .
2.If "WIRE CTR DELAY'' is set as other parameters, you switch one video screen to another one by wire control switch,
once the delay time is up, the screen will be automatically back to the pre-switching video screen.
MENU SETTING
The settings menu can only be accessed by using the remote control as described below.
When the car is in reverse, short press “ ”, you can switch among “PICTURE”, “SYSTEM”,“SETTING” or enter out.
When you enter “PICTURE”, press “ ” to switch among the items.“ ” and “ ” are to change the gure
of each setting. “SYSTEM”, “SETTING” is the same as explains above.
PICTURE
BRIGHTNESS 50
50
50
CONTRAST
COLOR
Remote control
Menu setting guidance
In “full display screen” state, short press “ ” to enter into menu setting interface .“ ” and “ ” are to
change the gure of each setting.
2. Mirror without Split-screen Function
1. Mirror with Split-screen Function
Enter picture menu
Menu parameter decreases
Guide line up
Guide line left
Enter guide line adjustment
Guide line clockwise
Guide line anti-clockwise
Menu parameter increases
Guide line right
Guide line down
Shortcut key for channel switch
BRIGHTNESS
50
11 12
9 10
12 1313 14
ADJUSTABLE GUIDE LINE
About guide line
What the regular guide line is
3m
1m
2m
0.4m
MXT.71D
Generally, to help drivers estimate the
distance from obstacles, there are three
lines for reference -red, yellow and
green.Those lines are displayed on the
monitor when reversing. The green line
is 3m away from the back of car and the
yellow line is 2m. The distant red line
is1m away from the backside of car
while the closed red line is 0.4m. Both
reference lines on the left and right
should leave 0.2m from the car.
Regular guide line is xed. But installation sites of cameras
are different as well as car size. The xed guide line is not
accurate enough for drivers. There is a great difference
among regular and xed guide lines and car's real guide
lines, especially when camera is mounted on the left or
right side of car backside.
3m
2m
1m
How to adjust the guide line
Caution: keep the remote control 0.5m-1.0m from rearview mirror when you use the remote to adjust the
parking lines.
Using the remote control, the positions and angles of the guidelines can be adjusted to suit each individual car.
Reversing state: Press setting button to enter “guide line adjustment” mode. The system is defaulted to adjust left
guide line rst. Press the button again to switch to adjust the right guide line.
The up , down , left and right buttons are to adjust the corresponding location of guide lines. The
clockwise rotation and contra rotating buttons are to adjust the angles of guide lines. It is easy to operate
and calibrate. calibration nished, switch the reverse gear to save the information.
R
Display on the monitor
L
Right position
Wrong position
UP
Clockwise
Down
Right
left
Move the
guide line
Rotate the
guide line
anticlockwise
Press the button to choose the L or R
adjustable guideline.
Remote control
11 12
-
1
-
2
-
3
-
4
-
5
-
6
-
7
BrandMotion 9002-7692v2.pdf Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
BOYO VISION VTW73M User manual
-
Volvo S80 2012 Owner's manual
-
BMW X3 xDrive35i Owner's manual
-
Volvo 2013 XC60 Owner's manual
-
Volvo XC70 2013 Owner's manual
-
Volvo XC60 Twin Engine Owner's manual
-
-
Yada BT53328F-1 User manual
-
Volvo V90 Cross Country Owner's manual
-
