OWNER’S MANUAL
CKS3029
Visit our web site at www.emersonradio.com
Dual Alarm AM/FM Clock Radio
with SmartSet
®
Auto Time Setting System
and Sure Alarm
(U.S. Patent No. 6,567,344)
CKS3029_080106.p65 1/8/2006, 9:2522
1
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
1.) Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
2.) Do not use this apparatus near water.
3.) Clean only with dry cloth.
4.) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
5.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
6.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
7.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
8.) Only use attachments / accessories specified by the manufacturer.
9.) Unplug this apparatus during lightning storms or when unused for long periods of time.
10.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
11.) This appliance shall not be exposed to dripping or splashing water and no object filled with liquids
such as vases shall be placed on the apparatus.
12.) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13.) Do not overload wall outlet. Use only power source as indicated.
14.) Use replacement parts as specified by the manufacturer.
15.) The product may be mounted to a wall only if recommended by the manufacturer.
16.) Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks.
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrow-
head symbol, within an equi-
lateral triangle is intended to
alert the user to the presence
of uninsulated ‘dangerous voltage’
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
The exclamation point within
an equilateral triangle is in-
tended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in
the literature accompany-
ing the appliance.
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER
(OR BACK), NO USER
SERVICEABLE PARTS INSIDE
REFER SERVICING TO
Q U A LI FI ED SE RVI C E
PERSONNEL.
CAUTION
The Caution Marking maybe located at the bottom enclosure of the apparatus.
CKS3029_080106.p65 1/8/2006, 9:251
2
Congratulations!
And thank you for purchasing the SmartSet
®
Clock Radio from Emerson Research.
SmartSet
®
is the world’s first and only LED clock radio that will automatically set
itself to the correct ‘Year’, ‘Month’, ‘Date’, ‘Day’, and ‘Time’ as soon as you plug it in.
The only thing you have to do is tell the SmartSet
®
what time zone you are in, and
the built in computer does everything else for you immediately. And not only the
first time, but every time the power is interrupted as well.
We all know how annoying it is to wake up in the morning and see the dreaded
flashing “12:00” display on our clocks or clock radios. This means that your power
was interrupted some time during the night while you were sleeping and your clock
doesn’t know what time it is anymore. Unfortunately it probably also means that
you are late for work, or for school, again. But with your SmartSet Clock Radio the
dreaded flashing “12:00” display is a thing of the past. The SmartSet
®
resets itself
as soon as the power is restored and gets you up on time, every time.
And if that isn’t enough, the SmartSet
®
computer also knows when Daylight Saving
Time begins and ends and it will adjust itself for those changes automatically through
the year 2099! Leap Years too! And best of all, the long life lithium battery backup
battery is already installed in your radio. You don’t have to remember to put a new
9-volt battery in your radio every 6 months. Under normal circumstances the lithium
battery can last for up to 5 years, and when it does need to be changed, a low
battery indicator will ‘flash’ to let you know. The CR2430 lithium battery is available
almost anywhere that batteries are sold.
The SmartSet
®
also gives you dual alarms that can be set to go off on weekdays
only, weekends only, or all 7 days. You can set one alarm to wake you up to buzzer
Monday through Friday when you have to get up early, and use the second alarm
to wake you up to soft music on Saturday and Sunday when you can sleep in.
Someday all clocks and clock radios may be this smart. But today the technology
is only available from Emerson Research.
We’re sure you’ll be happy and amazed by your SmartSet
®
Clock Radio, and that it
will give you many years of enjoyment and dependable service.
Once again, all of us at Emerson Research thank you for your purchase.
CKS3029_080106.p65 1/8/2006, 9:252
3
IMPORTANT NOTES
• Operate controls and switches as
described in the manual.
• Before turning on the power, make
certain that the power cord is properly
installed.
• When moving the set, be sure to first
disconnect the AC power cord.
• Avoid installing this unit in places
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much
heat, places lacking ventilation or dusty
areas, places subject to constant
vibration and/or humid or moist areas.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CKS3029_080106.p65 1/8/2006, 9:253
4
UNPACKING AND SET UP
• Remove the radio from the carton and remove all packing material from the
radio. We suggest that you save the packing material, if possible, in the unlikely
event that your radio ever needs to be returned for service. The original carton
and packing material is the only safe way to pack your radio to protect it from
damage in transit.
• Remove any descriptive labels or stickers on the front or top of the cabinet. Do
not remove any labels or stickers from the back or bottom of the cabinet.
• Note the serial number on the bottom of your radio and write this number in the
space provided on the Warranty page of this manual.
• Place your radio on a level surface such as a table, desk or shelf, convenient
to an AC outlet, out of direct sunlight, and away from sources of excess heat,
dirt, dust, moisture, humidity, or vibration.
• Unwind the AC power cord and extend it to its full length. The FM antenna is
built in to this cord. It must be fully extended to provide the best FM reception.
PREPARATION FOR USE
PROTECT YOUR FURNITURE
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
CKS3029_080106.p65 1/8/2006, 9:254
5
POWER SOURCE
This radio is designed to operate on normal 120V 60Hz AC power only. Do not
attempt to operate the radio on any other power source. You could cause damage
to the radio that is not covered by your warranty.
This radio should be connected to an AC outlet that is always ‘live’. Do not connect
it to an outlet that is controlled by a wall switch. When the power to the radio is
interrupted, the built in lithium battery takes over to maintain the time and alarm
settings. To maximize the life of the lithium battery keep the radio connected to a
‘live’ AC outlet at all times.
You will note that this system is equipped with a polarized AC power plug having
one blade wider than the other.
This is a safety feature. If this plug does not fit
into your existing AC outlet, do not try to defeat
this safety feature by filing the wide blade to
make it fit into your outlet. If this plug will not fit
into your outlet, you probably have an out-dated
non-polarized AC outlet. You should have your
outlet changed by a qualified licensed
electrician.
SURE ALARM BATTERY BACK-UP SYSTEM
This SmartSet
®
Clock Radio includes a Sure Alarm battery back-up circuit that can
wake you up even if the power is ‘Off’ at the selected wake up time. If your power
is ‘Off’ at the selected wake up time the clock display will be off and the radio will
not operate, but a separate mini-buzzer will turn ‘On’ automatically to wake you up,
even if you had selected the “Wake to Radio” option. The Sure Alarm will sound for
30 seconds and then shut off automatically.
To stop the Sure Alarm buzzer immediately, press the RADIO ON/OFF button.
Pressing the SNOOZE button has no effect during Sure Alarm operation.
NOTE: In order to maximize the life of the built in lithium battery, please be
sure to set the ALM 1 and ALM 2 switches to the “OFF” position if the radio will
be disconnected from the AC outlet for more than a few hours. This will prevent
the Sure Alarm from turning ‘On’ unecessarily.
AC Plug
AC Outlet
CKS3029_080106.p65 1/8/2006, 9:255
6
M
O
N
T
H
/
D
A
T
E
T
I
M
E
T
I
M
E
Z
O
N
E
A
L
M 1
A
L
M
2
A
L
M
M
O
D
E
D
O
W
N
U
P
SNOOZE
SLEEP
Y
E
A
R
S
E
T
SLEEP OFF
LOCATION OF CONTROLS AND INDICATORS
27
1
2
3
4
5
6
7
8
13
12
11
15
14
16
17
18
20
21
24
25
23
26
22
10
9
19
FRONT PANEL
LEFT SIDE PANEL
RIGHT SIDE PANEL
TOP PANEL
BUZZER
ALM 1
RADIO
OFF
ALM 2
RADIO
BUZZER
OFF
DIMMER
HI
LO
CKS3029_080106.p65 1/8/2006, 9:256
7
FRONT PANEL
1.) Lighted Dial Pointer.
2.) LOW BATT. LED Indicator.
3.) ALM 1 ‘On’ Indicator.
4.) AM indicator.
5.) Time/Date Display.
6.) ALM 2 ‘On’ Indicator.
7.) Day LED Indicators.
8.) Back Up Battery Compartment (Bottom Cabinet).
TOP PANEL
9.) RADIO ON/OFF Button.
10.) MONTH/DATE Setting Button.
11.) TIME Setting Button.
12.) TIME ZONE Button.
13.) AC Power Cord (Back Cabinet).
14.) Speaker (Back Cabinet).
15.) ALM (Alarm) 1 setting Button.
16.) ALM (Alarm) 2 setting Button.
17.) ALM (Alarm) MODE (Weekdays/Weekends/Everyday Alarm) Button.
18.) DOWN SET Button.
19.) UP SET Button.
20.) SLEEP Button (Sleep To Music Timer).
21.) SNOOZE (SLEEP OFF) Button.
LEFT SIDE PANEL
22.) Display DIMMER (HI/LO) Switch .
23.) ALM (Alarm) 2 (RADIO/BUZZER/OFF) Selector Switch.
24.) ALM (Alarm) 1 (RADIO/BUZZER/OFF) Selector Switch.
RIGHT SIDE PANEL
25.) VOLUME Control.
26.) Band (AM/FM) Switch.
27.) TUNING Control.
CKS3029_080106.p65 1/8/2006, 9:257
8
OPERATING INSTRUCTIONS
SETTING THE TIME, THE FIRST TIME
IMPORTANT: The first time you connect your new SmartSet
®
clock radio to the
AC outlet the internal computer will automatically set the time correctly for the
Eastern Time Zone, which is the initial default setting. The display will scan for a
few seconds and then show the correct Day and Time in the Eastern zone. If you
live in the Eastern Time zone, there’s nothing else to do. Your clock is set correctly
and running.
If you do not live in the Eastern Time zone you must change the default zone
display to your own zone. You only do this one time and the SmartSet
®
will remember
the new default zone setting and will always return to that setting after a power
interruption
There are 7 time zones programmed into your SmartSet
®
clock radio as follows:
ZONE 1 — Atlantic Time
ZONE 2 — Eastern Time (Default Setting)
ZONE 3 — Central Time
ZONE 4 — Mountain Time
ZONE 5 — Pacific Time
ZONE 6 — Yukon Time
ZONE 7 — Hawaiian Time
To change the default time zone display, depress the TIME ZONE button.
The number “2” will appear on the display
indicating that the default zone is ZONE 2,
Eastern Time.
Hold the TIME ZONE button and then press either the UP or DOWN buttons until
your own time zone appears on the display, then release the buttons. The clock
display will change to the correct time in the time zone you selected. The clock will
always return to the correct time in the zone you selected after every power
interruption. If you move to a different time zone, simply change the default zone
display to the new zone and the SmartSet
®
will remember that setting for you.
CKS3029_080106.p65 1/8/2006, 9:258
9
DATE DISPLAY
To see the correct date at any time, depress the MONTH/DATE button.
The display changes from time to Month and
Date (mm/dd).
For example, May 21
st
will appear as “5 21”.
When you release the MONTH/DATE button the display returns to the correct
time.
YEAR DISPLAY
To see the correct year, depress the MONTH/DATE and TIME buttons together.
The display changes from time to year.
When you release the MONTH/DATE and TIME buttons the display returns to the
correct time.
DAYLIGHT SAVING AND LEAP YEAR ADJUSTMENTS
All Daylight Saving and Leap Year adjustments are made automatically by
the SmartSet
®
internal computer as follows:
• Start of Daylight Saving Time:
At “2:00 AM” on the 2nd Sunday in March, the clock will automatically
advance to “3:00 AM”.
• End of Daylight Saving Time:
At “3:00 AM” on the 1st Sunday in November, the clock will automatically
reset to “2:00 AM”.
• Leap Year:
At “12:00 Midnight” on February 28th, the calendar display will change
to “2 29”.
CKS3029_080106.p65 1/8/2006, 9:259
10
MANUAL TIME ADJUSTMENTS
Some people like to set their clocks 5 to 10 minutes fast to make sure that they will
always be on time. Even though the SmartSet
®
sets the time by itself, you still have
the option of adjusting the time manually if you wish.
To manually adjust the time display depress and hold the TIME button, and press
either the UP or DOWN buttons to adjust the time display ahead or back as desired.
Each press of the UP or DOWN buttons will change the display by one minute. If
you hold the UP or DOWN buttons the display will continue to change. The display
will change slowly at first, one minute at a time. But if you continue holding the UP
or DOWN buttons the display will change rapidly.
Note:If you manually adjust the time, your new setting is entered into the SmartSet
®
memory. If the power is interrupted, the display will return to your new setting, not
the original setting, when the power is restored.
ADJUSTING THE WAKE UP TIMES
Your SmartSet
®
clock radio has two separate alarms that can be set and used
independently. You may use the alarms to wake two people at different times, or
you may use one alarm for weekdays and the other for weekend wake up times.
The procedure for adjusting the wake up time is the same for both Alarm 1 and
Alarm 2.
1.) Depress and hold either the ALM 1 or ALM 2 setting button. The display will
change from the correct time to the Alarm 1 or Alarm 2 wake up time.
2.) While holding the ALM 1 or ALM 2 setting button, depress either the UP or
DOWN button to move the display ahead or back to your desired wake up time.
3.) When the desired wake up time appears on the display, release the UP or
DOWN buttons.
Note: Be sure that you have set the wake up time correctly by observing the
AM indicator. If the AM indicator is ‘On’ the wake up time is “AM”. If the AM
indicator is ‘Off’, the wake up time is “PM”.
4.) When the desired wake up time (AM or PM) appears on the display, release
the ALM 1 or ALM 2 setting buttons.
CKS3029_080106.p65 1/8/2006, 9:2510
11
SELECTING THE ALARM MODE
Your SmartSet
®
clock radio allows you to select from among three different alarm
operation modes for either alarm. The alarm modes are:
• Everyday – the alarm will turn on all 7 days.
• Weekdays only – the alarm will only turn on Monday through Friday;
• Weekends only – the alarm will only turn on Saturday and Sunday.
To check the Alarm Mode setting for Alarm 1, depress the ALM 1 setting button.
The display will show the Alarm 1 wake up time and the day of the week indicators
will show you the alarm mode which is selected.
• If all 7 indicators are ‘On’, the Everyday mode is selected.
• If only the Monday through Friday indicators are ‘On’, the Weekdays only mode
is selected.
• If only the Saturday and Sunday indicators are ‘On’, the Weekends only mode is
selected.
To change the Alarm Mode setting for Alarm 1, hold the ALM 1 setting button and
press the ALM (Alarm) MODE button until the day indicators show the desired
mode setting, Weekdays only, Weekends only, or Everyday operation.
Release the ALM MODE and ALM 1 setting buttons and the display will return to
the correct time.
Follow the same procedure to select the desired Alarm Mode for Alarm 2 if
necessary.
CHECKING THE WAKE UP TIMES AND ALARM MODE
Whenever you want to check the wake up time or the alarm mode settings, simply
press either the ALM 1 or ALM 2 setting buttons. The display will change from
correct time to wake up time and the day indicators will show you the alarm mode
which is currently selected.
Release the ALM 1 or ALM 2 setting buttons to return to correct time.
CKS3029_080106.p65 1/8/2006, 9:2511
12
LISTENING TO THE RADIO
1.) Set the Band selector to the desired band, AM or FM.
2.) Set the VOLUME control to a low setting.
3.) Press the RADIO ON/OFF button to turn the radio ‘On’. The radio dial pointer
will light.
4.) Select your desired station with the TUNING control.
5.) Adjust the Volume control to the desired setting.
6.) When you are finished listening, press the RADIO ON/OFF button to turn the
radio ‘Off’. The radio dial pointer light goes off.
ANTENNA INFORMATION
AM – The AM bar antenna is inside the cabinet. If AM reception is weak, change
the position of cabinet until the internal antenna picks up the strongest signal.
FM –The FM antenna is built in to the AC power cord. If FM reception is weak try
varying the position and direction of the power cord until you find the strongest
signal.
CKS3029_080106.p65 1/8/2006, 9:2512
13
WAKE TO RADIO
1.) Turn the radio ‘On’ and select the band, station, and volume level that you wish
to hear when the alarm comes on, then turn the radio ‘Off’ again.
2.) Reconfirm the wake up time and alarm mode settings for the alarm you are
using, Alarm 1, Alarm 2, or both alarms.
3.) Set the ALM (Alarm) selector switch for one or both alarms to the ‘RADIO’
position. The appropriate ALM 1 and/or ALM 2 indicators will light up to confirm
that the alarms are set.
4.) At the selected wake up time the radio will turn ‘On’. It will play for one hour and
then shut off automatically.
5.) To stop the radio sooner, press either the appropriate ALM 1 or ALM 2 button,
or press the RADIO ON/OFF button. The radio will stop but the alarm remains
set and will turn the radio on again at the same time on the following day
(depending on the Alarm Mode setting).
6.) If you do not want the alarm to turn the radio on the following day, set the
appropriate ALM selector to the “OFF” position.
CKS3029_080106.p65 1/8/2006, 9:2513
14
WAKE TO BUZZER (Crescendo Alarm)
NOTE: Alarm 1 and Alarm 2 have different buzzer sounds.
•Alarm 1 is a “Single beep” sound.
•Alarm 2 is a “Double beep” sound.
You will be able to tell which alarm is going off by the sound that it makes.
1.) Reconfirm the wake up time and alarm mode settings for the alarm you are
using, Alarm 1, Alarm 2, or both alarms.
2.) Set the ALM selector switch for one or both alarms to the BUZZER position.
The appropriate ALM 1 and/or ALM 2 indicators will light up to confirm that the
alarms are set.
3.) At the selected wake up time the buzzer will sound. It will begin softly and
gradually increase in volume to wake you up. It will continue for one hour and
then shut off automatically.
4.) To stop the buzzer sooner, press either the appropriate ALM 1 or ALM 2
button. The buzzer will stop but the alarm remains set and will turn the buzzer
on again at the same time on the following day (depending on the Alarm Mode
setting).
To stop the buzzer and turn on the radio immediately, press the RADIO
ON/OFF button instead of the ALM 1 or ALM 2 button.
5.) If you do not want the alarm to turn the buzzer on the following day, set the
appropriate ALM selector to the “OFF” position.
RADIO AND BUZZER OPERATION
You may also set one alarm for wake to radio and the other for wake to buzzer.
Just set the ALM 1 and ALM 2 selector switches to the desired positions.
SNOOZE ALARM
After the radio or buzzer alarm sounds in the morning you may press the SNOOZE
Bar for a few more minutes sleep. The respective ALM indicator will flash.
The alarm will stop for approximately 9 minutes and then turn on again. You may
repeat the Snooze operation up to seven times if desired, but after the seventh
time the alarm will not turn on again.
CKS3029_080106.p65 1/8/2006, 9:2514
15
SLEEP TO MUSIC TIMER
You can program the sleep timer to play the radio for up to 90 minutes and then
shut off automatically.
1.) Press the SLEEP button.
The display will briefly show “10” and the
radio will begin to play.
After 10 minutes the radio will shut off automatically. Each time you press the
SLEEP button the sleep timer will start at 10 minutes. This is the sleep timer
default setting.
2.) To increase or decrease the amount of time that the radio will play before
shutting off, hold the SLEEP button and press either the UP or DOWN button
to change the display to the desired sleep time, up to a maximum of 90 minutes
or a minimum of 2 minutes.
Note: When you change the sleep timer from the 10 minute default setting to
a different setting, the new setting becomes the default setting. Whenever you
activate the sleep timer it will begin with your new default setting and count
down to zero from that point.
3.) To cancel the sleep timer before it counts down to “00” and shut the radio ‘Off’
immediately, press the SNOOZE Bar.
IMPORTANT: Remember that the station and volume settings you choose for the
Sleep To Music operation are the same settings you will hear if you set the alarm
for wake to radio the following morning.
DIMMER CONTROL
The DIMMER control was set to the HI (High) position at our factory. If you find the
clock display is too bright in a darkened room, set the Dimmer control to the LO
(Low) position.
CKS3029_080106.p65 1/8/2006, 9:2515
16
1
2
CHANGING THE LITHIUM BATTERY
Like all batteries, eventually the built in lithium battery will need to be replaced. A
number of factors, such as, the length of time between the date the radio was
manufactured and the date you plugged it in for the first time determine the amount
of time before replacement. During this initial storage period, the lithium battery is
supplying power to the SmartSet
®
computer memory. Once you plug the radio in,
your household outlet supplies the power, and the battery is not being used. A
fresh lithium battery can supply power to the SmartSet
®
computer for at least 3
years even if it is never connected to an AC power supply. If your radio was
connected to your AC supply within a few months after it was manufactured, and
you experience only the normal, nuisance type, short duration power interruptions,
your battery may last for up to 5 years or even longer.
When the battery power drops below a certain level, the LOW BATT indicator will
‘flash’. When you see this indicator, you should change the battery as soon as it is
convenient for you to do so. To change the battery proceed as follows:
1.) Purchase a replacement 3V lithium battery wherever batteries are sold. The
battery type is CR2430 or equivalent.
2.) Remove the battery from its package so it is ready to install.
IMPORTANT: Leave the radio power cord connected to your AC outlet. This
will provide power to the SmartSet
®
computer memory while the original lithium
battery is removed.
3.) Turn the radio upside down and use a small screwdriver to remove the screws
securing the battery holder to the cabinet.
BE CAREFUL NOT TO LOSE THESE SMALL SCREWS!
4.) Remove the original battery from
the holder and insert the new
battery into the holder the same
way, observing the positive (+)
direction. Slide the holder with the
new battery back into the slot in the
cabinet.
5.) Replace the screws that secure the
battery holder in the cabinet.
6.) Turn the radio right side up and confirm that the LOW BATT indicator is ‘Off’.
7.) Save these instructions. You’ll have to do this again five to eight years from
now!
CR2430
CKS3029_080106.p65 1/8/2006, 9:2516
17
RESETTING THE CLOCK AFTER A TOTAL MEMORY LOSS
If you do not change the built in lithium battery within a reasonable period of time
after you see the ‘flashing’ LOW BATT. warning indicator, the lithium battery may
become exhausted and will no longer be able to supply back up power to the
SmartSet
®
internal computer. If the unit is disconnected from the AC outlet after
the battery is exhausted, or if a power interruption occurs, the SmartSet
®
memory
will be lost and the clock will need to be reset when the power is restored. Be sure
to install a fresh lithium battery before you reset the clock, otherwise the clock will
need to be reset each time the power is interrupted.
If the lithium battery is exhausted and you experience an interruption in the
AC power supply, the clock will reset itself to its initial default setting when the
power is restored.
The initial default setting is “AM 12:00, Saturday, January 1
st
(1 1), 2005”.
If you notice that the time on your SmartSet
®
clock radio is completely incorrect,
and the day indicator is also wrong, press the MONTH/DATE button to see the
Date. If the Date display is showing “1 1” (January 1
st
), you probably experienced
a total memory loss.
To reset the clock after a total memory loss, proceed as follows:
1.) Follow the instructions on page 16 and install a new CR2430 lithium battery in
the battery compartment.
2.) Connect the radio to your AC outlet and let the clock set itself.
3.) Depress the MONTH/DATE and TIME buttons together. The display will change
from ‘time’ to ‘year’.
While holding the MONTH/DATE and TIME buttons, press the UP button to
set the display to the correct year, then release the buttons.
4.) Depress the MONTH/DATE button. The display will change from ‘time’ to
‘month/date’ (mm/dd).
While holding the MONTH/DATE button, press the UP button to set the display
to the correct month and date. The Day indicator will change automatically as
you adjust the month/date settings. When the correct month and date appear
on the display, release the buttons.
CKS3029_080106.p65 1/8/2006, 9:2517
18
5.) Depress the TIME button and the UP button to set the display to the correct
time. Be sure to confirm that you have set the time correctly to ‘AM’ or ‘PM’ by
observing the AM indicator.
6.) After you set the time, reconfirm that the Day, and Month/Date displays are still
correct. Make final adjustments if necessary.
The SmartSet
®
clock memory is now reset and the new lithium battery will maintain
it for the next 5 to 8 years, depending on the number and duration of the power
outages you experience.
IMPORTANT NOTE:
After resetting the clock, don’t forget to reset your wake up times, and alarm mode
settings, and sleep timer settings as well.
CKS3029_080106.p65 1/8/2006, 9:2518
19
CARE AND MAINTENANCE
If the cabinet becomes dusty, wipe it with a soft cloth. If the cabinet becomes
smudged or dirty, clean it with a soft, slightly dampened cloth. Never allow
water or any liquid to get inside the cabinet. Never use any abrasive cleaners
or cleaning pads as these will damage the finish of your radio.
TO FIND THE LOCATION AND PHONE
NUMBER OF YOUR NEAREST SERVICE
CENTER PERMITTED TO PERFORM
WARRANTY...
CALL TOLL FREE: 1-800-695-0098
SERVICE
FOR CUSTOMER SERVICE,PLEASE WRITE TO:
Emerson Radio Corp.,
Consumer Affairs Dept.,
5101 Statesman Drive,
Irving, TX 75063.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
LITHIUM BATTERY PRECAUTIONS
• Dispose of the old battery properly. Do not leave it lying around where a young
child or pet could play with, or swallow it. If the battery is swallowed, contact a
physician immediately.
• Battery may explode if mistreated. Do not attempt to recharge it or disassemble
it. Do not dispose of the old battery in a fire.
CKS3029_080106.p65 1/8/2006, 9:2519
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Emerson CKS2237 User manual
- Category
- Alarm clocks
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI