American Standard 2705.118W User manual

American Standard
Brand
American Standard
Model
2705.118W
Category
Sanitary ware
Type
User manual

This manual is also suitable for

ELLISSE BUILT-IN™ WHIRLPOOL
HIGH GLOSS ACRYLIC
ELLISSE BUILT-IN WHIRLPOOL
Whirlpool Featuring System I:
❏ 2703.118W End Mount Pump, Right Hand Outlet
❏ 2703.218W End Mount Pump, Left Hand Outlet
❏ 2705.118W Front Mount Pump, Right Hand Outlet
❏ 2705.218W Front Mount Pump, Left Hand Outlet
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Dual, molded-in arm rests
• Integral 3-sided tiling/water retention flange
• 1.5 HP single speed, self-draining pump/motor
• Factory installed power cord and plug
• Six multi-directional and flow-adjustable jets
including:
- Two foot jets
- Two body massage jets
- Two back-rest jets
• Deck-mounted air switch On/Off
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
system
• Factory installed and tested whirlpool system
StayClean™ Whirlpool Featuring System I:
❏ 2703.118WC End Mount Pump, Right Hand outlet
❏ 2703.218WC End Mount Pump, Left Hand outlet
❏ 2705.118WC Front Mount Pump, Right Hand outlet
❏ 2705.218WC Front Mount Pump, Left Hand outlet
• Same as above except with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions: 1524 x 813 x 546mm
(60” x 32” x 21-1/2")
© 2003 American Standard Inc.
BV-17
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Rev. 3/03
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
To Be Specified - Required:
❏ Color:
❏ Bath Filler: (specify finish)
❏ Bath Drain: 1583.470 (specify finish)
❏ Grab Bar Kit: 9827-200-two per kit (specify finish)
To Be Specified - Optional:
❏ Safe-T-Heater*: 9075.120
❏ Ellisse Apron: 9160.2705(specify color)
❏ Jet Trim Ring Kit: 9860.200-two per kit (specify
finish)
For color/finish availability and other faucet choices,
please see the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.
ELLISSE BUILT-IN™ WHIRLPOOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
1524mm
(60)
PROVIDE ACCESS
TO PUMP FOR SERVICING
ON ALL INSTALLATIONS
229mm
(9)
387mm
(15-1/4)
51mm
(2)
813mm
(32)
533mm
(21)
1-1/2 N.P.T.
THREADS
1-1/2 O.D.
TAILPIECE
38mm
(1-1/2)
83mm
(3-1/4)
C/L OF DRAIN
OUTLET
FINISHED
WALL LINE
C/L OF
SUPPLIES
ON/OFF SWITCH
WATER RETENTION
FLANGE (3) SIDES
305mm
(12) OPT.
102mm
(4)
95mm
(3-3/4)
546mm
(21-1/2)
ROUGH
FLOOR
PUMP
ALT. PUMP
LOCATION
19mm
(3/4)
LEVELING
STRINGER
NOT FOR
SUPPORT
ROUGH
FLOOR
WATER
RETENTION
FLANGE
UNDERSIDE
OF DECK
FINISHED WALL
C/L OF
SPOUT
C/L OF
VALVES
C/L OF
SHOWER ARM
INTEGRAL
FEET
C/L OF
OVERFLOW
TOP
OF
DECK
38mm
(1-1/2)
1651-1981mm
(65-78)
OPTIONAL
229x305mm
(9x12) FLOOR
CUTOUT
51mm
(2)
SEE FITTING
SPECS FOR
DIMENSION
■
SAFE-T-HEATER
REMOVABLE BLANK
NOTES:
BATH MUST BE INSTALLED ABOVE THE FLOOR LINE AS BUILT-IN INSTALLATION. SUMP OF BATH IS SUPPORTED BY
INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL APRON NO. 9160.2705 & GRAB BAR KIT NO.9827.200 AVAILABLE AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
LEFT HAND OUTLET SHOWN, RIGHT HAND REVERSE DIMENSIONS 2703.118W/2705.118W.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY
HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
ON SYSTEM II: CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL, A MINIMUM OF 152mm (6) ABOVE ROUGH
FLOOR.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1.These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided pages.
GENERAL SPECIFICATIONS FOR 2703/5 WHIRLPOOL
60 x 32 x 21-1/2 In. (1524 x 813 x 546mm)
141 Lbs. (63 Kg.)
643 Lbs. (292 Kg.)
60 Gal. (277 L)
50 Gal. (189 L)
44-1/2 X 20 In. (1130 mm X 508 mm)
58 X 26-1/4 In. (1473 mm X 667 mm)
14-1/2 In. (368 mm)
48 Lbs./Sq.Ft. (231 Kgs./Sq.m)
20.8
35.3
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.6 HP, 9.7 AMPS, 120V.
2.1 HP, 15.6 AMPS, 120V.
SYSTEM I PUMP
SYSTEM II PUMP
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
ELLISSE BUILT-IN™ WHIRLPOOL
HIGH GLOSS ACRYLIC
ELLISSE BUILT-IN WHIRLPOOL
Whirlpool Featuring System II:
❏ 2703.128W End Mount Pump, Right Hand Outlet
❏ 2703.228W End Mount Pump, Left Hand Outlet
❏ 2705.128W Front Mount Pump, Right Hand Outlet
❏ 2705.228W Front Mount Pump, Left Hand Outlet
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Dual, molded-in arm rests
• Integral 3-sided tiling/water retention flange
• 2.0 HP, two speed, self-draining pump/motor
with pulse feature
• Factory installed power cord and plug
• Six multi-directional and flow-adjustable jets
including:
- Two foot jets
- Two body massage jets
- Two back-rest jets
• Deck-mounted electronic control with 20
minute built-in timed safety shut off and
Chrome Bezel
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
system
• Factory installed and tested whirlpool system
StayClean™ Whirlpool Featuring System II:
❏ 2703.128WC End Mount Pump, Right Hand outlet
❏ 2703.228WC End Mount Pump, Left Hand outlet
❏ 2705.128WC Front Mount Pump, Right Hand outlet
❏ 2705.228WC Front Mount Pump, Left Hand outlet
• Same as above except with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions: 1524 x 813 x 546mm
(60” x 32” x 21-1/2")
© 2003 American Standard Inc.
BV-18
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Rev. 3/03
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
To Be Specified - Required:
❏ Color:
❏ Bath Filler: (specify finish)
❏ Bath Drain: 1583.470 (specify finish)
❏ Grab Bar Kit: 9827-200-two per kit (specify finish)
To Be Specified - Optional:
❏ Safe-T-Heater*: 9075.120
❏ Ellisse Apron: 9160.2705(specify color)
❏ Jet Trim Ring Kit: 9860.200-two per kit (specify
finish)
❏ System II Control Bezel: 9861.200-two per kit
(specify finish)
For color/finish availability and other faucet choices,
please see the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.
ELLISSE BUILT-IN™ WHIRLPOOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
1524mm
(60)
PROVIDE ACCESS
TO PUMP FOR SERVICING
ON ALL INSTALLATIONS
229mm
(9)
387mm
(15-1/4)
51mm
(2)
813mm
(32)
533mm
(21)
1-1/2 N.P.T.
THREADS
1-1/2 O.D.
TAILPIECE
38mm
(1-1/2)
83mm
(3-1/4)
C/L OF DRAIN
OUTLET
FINISHED
WALL LINE
C/L OF
SUPPLIES
ON/OFF SWITCH
WATER RETENTION
FLANGE (3) SIDES
305mm
(12) OPT.
102mm
(4)
95mm
(3-3/4)
546mm
(21-1/2)
ROUGH
FLOOR
PUMP
ALT. PUMP
LOCATION
19mm
(3/4)
LEVELING
STRINGER
NOT FOR
SUPPORT
ROUGH
FLOOR
WATER
RETENTION
FLANGE
UNDERSIDE
OF DECK
FINISHED WALL
C/L OF
SPOUT
C/L OF
VALVES
C/L OF
SHOWER ARM
INTEGRAL
FEET
C/L OF
OVERFLOW
TOP
OF
DECK
38mm
(1-1/2)
1651-1981mm
(65-78)
OPTIONAL
229x305mm
(9x12) FLOOR
CUTOUT
51mm
(2)
SEE FITTING
SPECS FOR
DIMENSION
■
SAFE-T-HEATER
REMOVABLE BLANK
NOTES:
BATH MUST BE INSTALLED ABOVE THE FLOOR LINE AS BUILT-IN INSTALLATION. SUMP OF BATH IS SUPPORTED BY
INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL APRON NO. 9160.2705 & GRAB BAR KIT NO.9827.200 AVAILABLE AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
LEFT HAND OUTLET SHOWN, RIGHT HAND REVERSE DIMENSIONS 2703.118W/2705.118W.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY
HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
ON SYSTEM II: CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL, A MINIMUM OF 152mm (6) ABOVE ROUGH
FLOOR.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1.These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided pages.
GENERAL SPECIFICATIONS FOR 2703/5 WHIRLPOOL
60 x 32 x 21-1/2 In. (1524 x 813 x 546mm)
141 Lbs. (63 Kg.)
643 Lbs. (292 Kg.)
60 Gal. (277 L)
50 Gal. (189 L)
44-1/2 X 20 In. (1130 mm X 508 mm)
58 X 26-1/4 In. (1473 mm X 667 mm)
14-1/2 In. (368 mm)
48 Lbs./Sq.Ft. (231 Kgs./Sq.m)
20.8
35.3
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.6 HP, 9.7 AMPS, 120V.
2.1 HP, 15.6 AMPS, 120V.
SYSTEM I PUMP
SYSTEM II PUMP
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

American Standard 2705.118W User manual

American Standard
Brand
American Standard
Model
2705.118W
Category
Sanitary ware
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents