Ariston Washer User manual

Brand: Ariston

Model: Washer

Category: Washing machines

Type: User manual

This manual is also suitable for

English, 1

Contents

Important safety instructions 2-3

Important safety instructions

Grounding Instructions

Safety

Installation instructions 4-5-6

Unpacking and leveling

Minimum Installation Spacing

Connecting Water Inlet

Drainage

Connecting the drain hose

Electrical

Under Sink Method

Technical data

Description of the washing machine

and starting a wash cycle 7-8

Control panel

Indicator lights

Starting a wash cycle

Wash cycles 9

Table of wash cycles

Special wash cycles

Personalisation 10-11

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry 12

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Load balancing system

Helpful Hints

Care and maintenance instructions 13

Cutting off the water and electricity supplies

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting 14

Service 15

Warranty, 16-17

ARWXF 129 W

Instructions for use

WASHING MACHINE

Splendide

IMPORTANT SAFETY INSTRUCTIONS

WARNING - To reduce the risk of fire, electrical shock, or

injury to persons when using your appliance, follow basic

precautions, including the following:

• Read all instructions before using the appliance.

• Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline, dry

cleaning solvents, other flammable, or exlosive substan-

ces as they give off vapors that could ignite or explode.

• Do not allow children to play on or in the appliance. Clo-

se supervision of children is necessary when the applian-

ce is used near children.

• Before the appliance is removed from service or discar-

ded, remove the door to the washing compartment.

• Do not add gasoline, dry cleaning solvents, or other flam-

mable or explosive substances to the wash water. These

substances give off vapors that could ignite or explode.

• Do not install or store this appliance where it will be

exposed to the weather.

• Do not tamper with controls.

• Under certain conditions Hydrogen gas may be produ-

ced in a hot water system that has not been used for 2

weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the

hot water system has not been used for such a period,

before using the appliance, turn on all hot water faucets

and let the water flow from each for several minutes.

This will release any accumulated hydrogen gas. As the

gas is flammable do not smoke or use an open flame

during this time.

• Turn off water faucets to relieve pressure on hoses and

valves and to minimize leakage if a break or rupture

occurs.

• Do not reach into the appliance if the tub or drum is

moving.

• Do not repair or replace any part of the appliance or

attempt any servicing unless specifically recommended

in the user-maintenance instructions or in published

user-repair instructions that you understand and have

the skills to carry out.

• Good, safe practices and caution MUST be applied

when installing, operating, and maintaining any applian-

ce. Follow basic precaution.

• Disconnect power to the washer at the circuit breaker

or fuse box, or unplug the machine in an emergency or

when servicing required. Have the installer show you and

label the proper switch or fuse at the electrical discon-

nect box.

• The interior of the appliance should be cleaned periodi-

cally by qualified service personnel.

• Before loading the washer, make sure the drum is empty.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of mal-

function or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistence for

electric current. This appliance is equipped with a cord ha-

ving an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet

that is properly installed and grounded in accordance with

all local codes and ordinances.

WARNING - Improper connection of the equipment-groun-

ding conductor can result in a electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the applian-

ce is properly gounded.

Do not modify the plug provided with the appliance: if it will

not fit outlet, have a proper outlet installed by a qualified

electrician.

Important safety instructions

Safety

CAUTION:

To reduce the risk of electric shock, DO NOT remove cover (or back)/no user servicable parts inside.

Refer for servicing to qualified services personnel.

The model number of this product may be found on the back of the unit; the serial number of the label affixed inside the door

and to the back of the unit.

You should note the model and serial numbers of this unit in the space provided. Retain this booklet as a permanent record

of your purchase to aid in identification in the event of theft.

MODEL N.

SERIAL N.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

The linghtning flash with arrowhead symbol, within an equilateral triagle, is intended to alert the user to the presen-

ce of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitu-

te a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important opera-

ting and maintenance (servicing) instructions in the booklet.

Indesit Company offers to his customers products with the ENERGY STAR Label.

This appliance was tested by UL and conforms with both Canadian and U.S. UL safety requirements

and displays their Mark

CAUTION RISK

OF ELECTRIC

SHOCK DO

NOT OPEN

US LISTED

! This instruction manual should be kept in a safe place

for future reference. If the washer is sold, transferred or

moved, make sure that the instruction manual remains with

the machine so that the new owner is able to familiarise

himself/herself with its operation and features.

! Read these instructions carefully: they contain vital infor-

mation relating to the safe installation and operation of the

appliance.

Unpacking and levelling

Unpacking

1. Remove the washer from its packaging.

2. Make sure that the washer has not been damaged

during the transportation process. If it has been damaged,

contact the retailer and do not proceed any further with the

installation process.

3. Remove the 4 protective

screws (used during tran-

sportation) and the rubber

washer with the correspon-

ding spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need them

again if the washer needs to be moved to another location.

! Packaging materials should not be used as toys for

children.

Levelling

1. Install the washer on a flat sturdy floor, without resting it

up against walls, furniture cabinets or anything else.

2. If the floor is not perfectly

level, compensate for any

unevenness by tightening

or loosening the adjustable

front feet (see figure); the an-

gle of inclination, measured

in relation to the worktop,

must not exceed 2°.

Levelling the machine correctly will provide it with stability,

help to avoid vibrations and excessive noise and prevent it

from shifting while it is operating.

Minimum Installation Spacing

This appliance may be installed in a recessed area, closet

or alcove. The installation spacing is in inches and is the

minimum acceptable.

*Additional spacing should be considered for easy instal-

lation, servicing and compliance with local codes and

ordinances. Installations must conform with the minimum

dimensions indicated.

0" *

Recessed Front View

1" *

Side View

Installation instructions

A & B = 25" (62 cm) min. / 34" (86 cm) max.

Floor Standpipe

Wall Standpipe

Fig. 4

Standpipe Drain System - Installations require a minimum

1 ¼” (3.2 cm) diameter standpipe with a minimum carry

away capacity of 7 gallons (26 liters) per minute.

Wall or Floor Standpipe Drain System - The top of the

standpipe must be between 25” (62 cm) - 34” (86 cm)

from the bottom of the washer (Fig. 4).

Sink Drainpipe System

Entry into the sink drain

system must be above the trap (Fig. 5). When routing the

drain hose through cabinets or walls, use a protective ma-

terial such as electrical or duct tape to cover sharp edges

that could damage the drain hose. Use a suitable clamp

to secure the drain hose to the “Y” branch or the disposer.

With a sink drainpipe system, you may connect directly:

1) to a disposer by following the manufacturers attachment

method.

2) directly to a “Y” branch tail piece (available at most

hardware stores).

3) Through the floor to a separate trap. The trap must be

vented to prevent siphoning. To provide proper venting,

install an Air Gap Kit (available at most hardware stores).

4) To the to the faucet using a Faucet Adapter Kit (available

separately).

• Use a U-Clamp (provided in your accessories packet)

or suitable item to secure the outlet end of the drain hose

(pre-installed on the back of your machine).

25" (62 cm) min.

with an air break

Laundry Sink Drain

Fig. 5

Sink Drain W/ "Y" Branch Tailpiece

Important:

Make sure that the drain hose is

not kinked and that water flow is not restricted.

Connecting Water Inlet

If the water pipes you will be connecting to are new or

unused, run the water until clear to remove any debris that

could clog the water valve screens or valves before con-

necting the machine. NOTE: Supply shut-off valves should

be easily accessible.

1. Screw the cold water fill

hose (C blue connector) onto

the cold water supply until

tight.

2. turn on the cold water

supply and check for leaks,

tighten if necessary.

3. Screw the hot water fill

hose (H red connector) onto

the hot water supply until tight.

4. Turn on the hot water supply and check for leaks,

tighten if necessary.

Drainage

• Standpipe Diameter/Capacity - Needs a 1 ¼”

minimum diameter standpipe with a minimum carry-away

capacity of 7 gallons per minute.

• Top of Standpipe - Must be between 25” - 34” high

from the bottom of the machine.

• Outlet End of Drain Hose (provided with the unit)

- Must be at least 20” above the bottom of the washer-

dryer. An air break must be available at the standpipe to

avoid siphoning. No more than 6” of the drain hose should

be inserted into the drain pipe to prevent siphoning.

Connecting the drain hose

It is possible for the water to be discharged into a sink,

standpipe or drainpipe, but an air break must be available

at a min. 20” height to prevent the machine from siphoning

(Fig. 6).

Important:

Water pressure MUST range wi-

thin the values indicated on the “Technical Data”

chart.

Important:

Do not use excessive force. Da-

mage to the couplings can result. The couplings

should be tightened by hand; a tool should only

be used if a leak occurs.

Electrical

• Machine Voltage/Amperage - 120V, 60 Hz, 4 Amp.

• Connection - 3-prong plug with 6’ cord is provided with

the machine.

• Circuit/Protector - 3-wire single phase, 120V, 60 Hz, AC,

on a separate 15 Amp circuit.

Technical Information

Technical data

Model

ARWXF 129 W

Dimensions

width: 23.4”” (59.5 cm)

height: 33.24”” - 33.75”” (84.5 - 85.7 cm)

depth: 22”” (55.9) cm

Weight

148 lbs

Minimum Installa-

tion Clearances

Sides: 0””

Front / Back: 1””

Capacity

Washing: 2 to 15 lbs. (1 to 7 kg)

Electrical

connections

Voltage: 120Volts, 4 A, 60 Hz

Water

connections

Max. Pressure: 0.69 MPa (6.9 bar), 100 psi

Min. Pressure: 0.05 MPa (0.5 bar), 7.2 psi

Max. Spin speed

up to 1200 RPM

Indesit Company offers to his customers

products with the ENERGY STAR Label.

This appliance was tested by UL and

conforms with both Canadian and U.S.

UL safety requirements and displays

their Mark.

US LISTED

• Insert the outlet end of the drain hose into the standpipe,

wall or floor drain (Fig. 6). NOTE: The outlet end of the

drain hose MUST be at least 20” (50 cm) above the base

of the machine. No more than 6” of the drain hose should

be inserted into the drain pipe to prevent siphoning.

• Use a strap, cable tie, or similar item to hold the hose or

the U-Clamp in place.

Under Sink Method

1. Cut the blocked end of

the under sink drainage unit.

2. Fix the hooked end sup-

porta minimum of 620 mm

from the floor.

3. Use a hose clip clamp to

securely attach the grey drai-

nage hose end to the under

sink drainage unit using a

hose. clamp

20" (62 cm) min.

34" (86 cm) max.

Standpipe

"Y" Tail Piece

This connection MUST be

before drain trap and at

least 20" (50.8 cm) above

the floor where washer will

be installed.

Cable tie

Floor Standpipe w/ "Y" Branch Tail Piece

Fig. 7

20" (50 cm) min.

with an air break

25" (62 cm) min.

34" (86 cm) max.

6" max.

Standpipe

Floor Standpipe

Fig. 6

U-Clamp

WARNING: To reduce the risk of fire, electric shock, or

injury to persons, read the IMPORTANT SAFETY IN-

STRUCTIONS before operating this appliance.

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button with indicator light: switches the machine

on and off.

If the indicator light is illuminated, this indicates that the

machine is switched on.

WASH CYCLE knob: programmes the wash cycles. During

the wash cycle, the knob does not move.

SPIN SPEED button: sets the spin speed or exclude the

spin cycle completely (see “Personalisation”).

TEMPERATURE button: sets the temperature or the cold

wash cycle (see “Personalisation”).

The wash temperatures selections are uniformly distribui-

ted.

DISPLAY: indicates the time remaining for the selected

wash cycle and, if a delayed start has been programmed,

the time remaining until the start of the wash cycle.

CONTROL PANEL LOCK button with indicator light:

activates or deactivates the control panel lock.

FUNCTION buttons with indicator light: used to select the

available functions. The indicator light corresponding to the

selected function will remain lit.

WASH CYCLE PROGRESS

indicator light

s: used to

monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is in

progress.

DOOR LOCKED indicator light: indicates whether the

door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or tem-

porarily interrupts the wash cycles.

NOTE: To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash orange,

while the indicator light for the current wash cycle phase

will remain lit in a fixed manner. If the DOOR LOCKED

indicator light is switched off, the door may be opened.

To start the wash cycle from the point at which it was inter-

rupted, press this button again.

Description of the washing

machine and starting a wash cycle

DOOR

LOCKED

indicator light

START/PAUSE

button with indicator

light

Control panel

WASH CYCLE PROGRESS

indicator lights

FUNCTION

buttons with

indicator lights

Detergent dispenser drawer

WASH CYCLE

knob

DISPLAY

ON/OFF

button with indicator

light

TEMPERATURE

button

SPIN SPEED

button

CONTROL PANEL LOCK

button with indicator light

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Wash cycle phase indicator lights

As the WASH CYCLE knob is rotated, the indicator lights

illuminate, indicating the stages which will be performed by

the machine in accordance with the selected wash cycle.

Once the desired wash cycle has been selected and has

begun, the indicator lights switch on one by one to indicate

which phase of the cycle is currently in progress.

Function buttons and corresponding indicator

lights

When a function is selected, the corresponding indicator

light will illuminate.

If the selected function is not compatible with the pro-

grammed wash cycle, the corresponding indicator light will

flash, a sound signal will be emitted and the function will

not be activated.

If a function which is incompatible with another function

selected previously, only the most recent selection will

remain active.

Temperature indicator light

When a temperature value is selected, the corresponding

indicator light will illuminate.

Spin indicator light

When a spin value is selected, the corresponding indicator

light will illuminate.

Control panel lock indicator light

To activate the control panel lock, press and hold the

button for approximately 2 seconds. When the indicator

light is illuminated, the control panel is locked. This means

it is possible to prevent wash cycles from being modified

accidentally, especially where there are children in the

home.

To deactivate the control panel lock, press and hold the

button for approximately 2 seconds.

Door locked indicator light

If this indicator light is on, the appliance door is locked to

prevent it from being opened accidentally; to avoid any

damage, wait for the indicator light to switch off before you

open the appliance door.

NOTE: If the DELAY TIMER function is activated, the door

cannot be opened; pause the machine by pressing the

START/PAUSE button if you wish to open it.

! If the START/PAUSE indicator light (orange) flashes

rapidly at the same time as the function indicator light, this

indicates a problem has occurred (see “Troubleshooting”).

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then

they will switch off and the START/PAUSE indicator light will pulse.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see “Personalisation”).

5. Set the spin speed (see “Personalisation”).

6. Measure out the detergent and washing additives (see “Detergents and laundry”).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed

manner, in green.

To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the (

) indicator light will switch on. The DOOR LOCKED indicator light will switch off, in-

dicating that the door may be opened. Take out your laundry and leave the appliance door ajar to make sure the drum dries

completely. Switch the washing machine off by pressing the ON/OFF button.

Wash

Rinse

Spin

Drain

End of wash cycle

Wash cycles

Table of wash cycles

Wash

cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max load

(lb)

Cycle

duration

Bleach Wash

Fabric

softener

Essentials cycles

Cottons Regular: Heavily soiled whites and resistant colours. Hot Max -

 

Max

Cottons Colored: Lightly soiled whites and delicate colours. Warm Max -

 

Max

Permanent Press: Normally soiled synthetics or permanent press labelled

garments.

Warm 800 -

 

6.6

Quick Wash

Warm Max -

 

2.20

Mixed Load 30 min.:To refresh lightly soiled garments quickly (not suitable

for wool, silk and clothes which require washing by hand).

Warm 800 -

 

6.6

Special wash cycles

Bright White: Heavily soiled whites and resistant colours. Warm Max

  

Max

Jeans

Warm 800 -

 

6.6

Active Wear

Warm 600 -

 

6.6

Infant Wear: Heavily soiled delicate colours Warm 800 -

 

4.4

Lightly Soiled 15 min.: To refresh lightly soiled garments quickly

(not suitable for wool, silk and clothes which require washing by hand)

Warm 800 -

 

3.30

Delicates

Delicate: Lightly soiled delicates colours. Warm 800 -

 

6.6

Silk/Curtains

Warm 0 -

 

2.20

Wool: for wool, cashmere, etc. Warm 600 -

 

3.30

Partials wash cycles

Rinse

- Max - -



Max

Spin

- Max - - - Max

Drain

- - - - - Max

The duration of the wash cycles can be checked on the display.

Special wash cycles

Permanent press (wash cycle 3) this cycle has less mechanical agitation and spinnig speed designed to reduce wrinkles.

Mixed Load (wash cycle 5) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minu-

tes and therefore saves both energy and time. By selecting this wash cycle (5 at WARM temperature), it is possible to

wash different fabrics together (except for wool and silk items), with a maximum load of 6.6 lb - (3 kg).

Bright White (wash cycle 6) Use this cycle when bleaching with hypoclorite based products.

Pour the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled “Detergent

dispenser drawer”).

Active wear (wash cycle 8) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results,

we recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a

liquid detergent and dosage suitable for a half-load.

Infant Wear (wash cycle 9). This wash cycle can be used to remove the soiling typically caused by babies, while ensuring

that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The cycle

has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect of special

disinfecting additives added to the detergent.

At the end of the wash cycle, the machine will slowly rotate the drum to prevent the formation of creases; to end the cycle

press the START/PAUSE button.

Lightly Soiled 15 min. (wash cycle 10) this wash cycle was designed to wash lightly soiled garments quickly: it lasts

just 15 minutes and therefore saves both energy and time. By selecting this wash cycle (10 at WARM temperature), it is

possible to wash different fabrics together (except for wool and silk items), with a maximum load of 3.30 lb - (1.5 kg).

For this cycle we recommend pretreating stains, shirt necks and wrists with specific antistain products.

Setting the temperature

By pressing the TEMPERATURE button to set the wash temperature. (See Table of wash cycles) Wash temperature can be

set selecting , “Cold”, “Warm”, “Hot” or 2 in-between positions which correspond to intermediate levels of water tempe-

rature (example: the position between “cold” and “warm” is lukewarm). See below for the indication in °C and °F for each

temperature position.

The available selections are:

Setting the spin speed

By pressing the SPIN SPEED button to set the spin speed for the selected wash cycle.

The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

Cottons 1200 rpm only

Synthetics 800 rpm

Wool 600 rpm

Silk drain only

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .

The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed

set for each wash cycle.

Note 1: During the (Cotton) cycles 1 and 2, it is not possible to eliminate the spin cycle or reduce the pre determined spin speed.”

Note 2: For the first two Programmes (Cottons Regular and Cottons Colored) the garments will be spun at maximum speed.

This allows to get the most from the spinning phase and reduce time and energy needed for the drying.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the

selected wash cycle.

Delay timer

To set a delayed start for the selected wash cycle, press the button repeatedly until the desired delay time is displayed (this

may be between 1 hour and 24 hours).

To disable the function press the button until the text

is displayed.

NOTE: Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it.

! This option is enabled with all programmes.

Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this

function offers a high-performance wash.

! This function may not be used in conjunction with wash cycles 4, 5, 7, 10, 12, 13, A, B, C.

Extra rinse

By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

! This function may not be used in conjunction with wash cycles 5, 10, B, C.

Personalisation

• Tap water

• Cold 15 °C/ 59 °F

• 30 °C/ 86 °F

• Warm 40 °C/ 104 °F

• 50 °C / 122 °F

• Hot 57°C / 134 °F

Reduced Wrinkles

By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At the end

of the cycle the washing machine will perform slow rotations of the drum; the REDUCED WRINKLES indicator light will switch

on and the START/PAUSE indicator light will flash in an orange colour and the phase END will remain lit in a fixed manner.

To end the cycle, press the START/PAUSE button or the REDUCED WRINKLES button.

For the Silk/Curtains cycle, the machine will end the cycle while the laundry is soaking and the REDUCED WRINKLES indi-

cator light will flash. To drain the water so that the laundry may be removed, press the START/PAUSE button or the REDU-

CED WRINKLES button.

! It may not be used with the 5, 8, 9, 10, 13, B, C.

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct dose of

detergent: adding too much detergent will not necessa-

rily result in a more efficient wash, and may in fact cause

build up on the inside of your appliance and contribute to

environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

Open the detergent di-

spenser drawer and pour

in the detergent or washing

additive, as follows.

compartment 1: Deter-

gent for the wash cycle

(powder or liquid)

Liquid detergent should only

be poured in immediately prior

to the start of wash cycle.

compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 3: Bleach

Bleach cycle

Bleaching may only be performed in conjunction with wash

cycles 6. Pour the bleach into extra compartment 3; pour

the detergent and softener into the corresponding com-

partments, then select one of the abovementioned wash

cycles.

This option is recommended only for very soiled cotton

garments.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label.

- the colours: separate coloured garments from whites

• Empty all garment pockets and check the buttons.

• Do not exceed the listed values, which refer to the weight

of the laundry when dry:

Durable fabrics: max. 15 lb - (7 kg)

Synthetic fabrics: max. 6.6 lb - (3 kg)

Delicate fabrics: max. 4.4 lb - (2 kg)

Wool: max. 3.30 lb - (1,5 kg)

How much does your laundry weigh?

1 sheet 14-17 oz - (400-500 g)

1 pillow case 5-7 oz - (150-200 g)

1 tablecloth 14-17 oz - (400-500 g)

1 bathrobe 31-42 oz - (900-1200 g)

1 towel 5-8 oz - (150-250 g)

Garments requiring special care

Jeans: Turn garments inside-out before washing.

Use programme 7.

Silk: use special wash cycle 12 to wash all silk garments.

We recommend the use of special detergent which has

been designed to wash delicate clothes.

Curtains: fold curtains and place them in a pillow case or

mesh bag. Use wash cycle 12.

Wool: Ariston is the only washer manufacturer to have been

awarded the prestigious Woolmark Platinum Care endorsement

(M.0508) by the Woolmark Company, which means that all

woollen garments may be washed in the washer, even those

which state “hand wash only” on the label. Wash cycle 13

therefore offers complete peace of mind when washing woollen

garments in the washer (max. load 3.30 lb - 1,5 kg) and guaran-

tees optimal performance.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load is

not balanced correctly, the machine spins at a reduced spin

speed. If the load is excessively unbalanced, the washer-

performs the distribution process instead of spinning. To

encourage improved load distribution and balance, we

recommend small and large garments are mixed in the load.

Helpful Hints

Your washer features three different speeds during the wash

cycle. During the Cotton cycle the drum spins at 1,200 or 800

rpm. During Permanent Press the drum spins at 850 rpm.

During delicates, the drum spins at 500 rpm.

Use HE Liquid Fabric Softener. Fill the softener compartment

up to the level marked. Using fabric softner fluffs out clothes

immediately after the wash cycle. This helps speed drying

time and reduce wrinkles.

Use Low sudsing Detergent. This is recommended for

all front loading washers. It ensures there is no over sudsing,

which may reduce the performance of your machine. Also,

this prevents damage to your machine which may be caused

When sorting laundry always take into consideration

the quantity and type of fabric contained in the load. Highly

absorbent fabrics such as those used in towels or jeans will

abosorb more water and become very heavy when saturated.

If you notice that your clothes are taking longer than usual to

dry may be overloading the machine, or washing too many

highly absorbent articles for a single load.

We recommend using Splendide All-Natural

Premium HE Laundry Powder (Part No. 1005). It

softens fabrics naturally and does not require the

use of a separate fabric softener.

At the end of the cycle, there may be water standing

in the Bleach or other compartments. This is

NORMAL. The Bleach compartment can be removed

when not in use.

Care and maintenance

instructions

Cutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle. This will

limit wear on the hydraulic system inside the washing

machine and help to prevent leaks.

• Unplug the washing machine when cleaning it and du-

ring all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the appliance

can be cleaned using a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

Remove the dispenser by

raising it and pulling it out

(see figure).

Wash it under running wa-

ter; this operation should be

repeated frequently.

Caring for the door and drum of your

appliance

• Always leave the porthole door ajar in order to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump

which requires little maintenance. Sometimes,

small items (such as coins or buttons) may fall into the pre-

chamber which protects the pump, situated in its bottom

part.

! Make sure the wash cycle has finished and unplug the

appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front part of

the washing machine (see

figure);

2. unscrew the lid by rota-

ting it anti-clockwise (see

figure): a little water may

trickle out. This is perfectly

normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any

cracks, it should be replaced immediately: during the wash

cycles, water pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be not solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

take in water (the indicator light for

the first wash cycle stage flashes

rapidly).

The washing machine continuously

takes in and drains water.

The washing machine does not

drain or spin.

The washing machine vibrates a lot

during the spin cycle.

The washing machine leaks.

The START/PAUSE indicator light

(orange) and the function indicator

lights flash rapidly.

There is too much foam.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set (using the Delay Timer, see “Personalisation”).

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the washing machine to fill with water and drain continuously. Special

anti-draining valves are available in shops and help to avoid this inconvenience.

• The wash cycle does not include draining: some wash cycles require the drain

phase to be started manually.

• The REDUCED WRINKLES function has been activated: To complete the

wash cycle, press the START/PAUSE button (“Personalisation”).

• The drain hose is bent (see “Installation”).

•

The drum was not unlocked correctly during installation (see “Installation”).

•

The washing machine is not level (see “Installation”).

•

The washing machine is trapped between cabinets and walls (see “Installation”).

•

The water inlet hose is not screwed on properly (see “Installation”).

•

The detergent dispenser drawer is blocked (for cleaning instructions, see

“Care and maintenance”)

•

The drain hose is not fixed properly (see “Installation”).

•

Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

•

The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

•

Too much detergent was used.

• The drainage duct is clogged.

• Check the pump pre-chamber.

Service

Before calling for Assistance:

•Check whether you can solve the problem alone (see “Troubleshooting”);

• Restarttheprogrammetocheckwhethertheproblemhasbeensolved;

• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedon

theguaranteecertificate.

! Alwaysrequesttheassistanceofauthorisedtechnicians.

Have the following information at hand:

• thetypeofproblem;

• theappliancemodel(Mod.);

• theserialnumber(S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found

onthefrontoftheappliancebyopeningthedoor.

All Splendide parts are available

direct from Westland Sales: 1-800-356-0766

If You Have You’ll Need to Buy

No access to Hot/Cold

water hookups

Splendide Faucet Adapter kit,

PartNo.154187104A(8ft,2.4m)

Water damage

Concerns

Splendide Drain-A-Way™ Pan, Part

No.PI-22,PI-24(orsimilar)

Floor drain

Siphon break kit (sold at most har-

dware stores)

Disposer drain

“Y”connector(soldatmosthardware

stores)

Shifting Concerns

(RV and Marine

Installations)

Splendide SecureFit™ instal-

lation Brackets,PartNo.MK01.

Keepswasherinplaceduringtravel

to prevent:

•Kinkedinlethoses

•Disconnecteddryerventhoses

•Crusheddryerventhose

•Blockeddispenserdrawer

•Knobsrubbingagainstcloseddoors

•Scuffedcabinetwoodwork

ARISTON ONE-YEAR LIMITED WARRANTY

(USA & CANADA ONLY)

WHO IS COVERED BY THIS WARRANTY

This limited one-year warranty (“Warranty”) is given only

to the original end-use/retail purchaser (the “First Using

Purchaser”) of the accompanying Ariston product(s) (the

“Ariston Product”).

If you purchased this Ariston Product from someone other

than an authorized Ariston reseller/dealer in the United States

or Canada, or if the Ariston Product was used (including but

not limited to floor models or refurbished products) prior to

your purchase, then you are not the First Using Purchaser

and the Ariston Product that you purchased is not covered

by this Warranty. This Warranty is not transferable.

WHAT IS COVERED BY THIS WARRANTY

Ariston will repair or replace any part of the Ariston Product

which fails due to a defect in materials or workmanship when

used under normal home-use conditions. Ariston will also

provide, free of charge, all labor and related services to repair

or replace the defective part.

This Warranty applies only to Ariston Products purchased

and used in the United States or Canada. Subject to the

exclusions below, for Ariston Products purchased in, but

used outside, the United States or Canada, this Warranty

covers only warranty service within the United States or

Canada (and does not include shipping outside the United

States or Canada).

LENGTH OF THE WARRANTY

This Warranty runs for a period of one (1) year from the date

of the original purchase by the First Using Purchaser. Please

note that a copy of your original purchase receipt showing

the purchase date and the vendor’s name and address are

required to obtain service under this Warranty. For the pur-

poses of determining the applicable warranty period, please

note that any and all replaced or repaired parts shall assume

the identity of the original.

WHAT IS NOT COVERED BY THE WARRANTY

(EXCLUSIONS)

This Warranty does not cover:

1. Improper installation, delivery, maintenance and/or im-

proper operation of the Ariston Product.

2. Damage caused if the Ariston Product has not been used

in compliance with the electricity or gas supply specifications

printed on the rating plate.

3. Failure of or damage to the Ariston Product if it is altered,

abused, misused, or used for other than the intended pur-

pose, or if it is used commercially.

4. Service trips to your home to provide instructions on the

use of your Ariston Product.

5. Replacement of house fuses or correction of the plumbing

or electric wiring in your home.

6. Damage caused by neglect, accident, fire, floods or acts

of God.

7. Physical Damage to the appearance of your Ariston

Product including, without limitation, scratches, rust, dents,

warping, peeling and the like.

8. Damage caused by transportation.

9. Replacement of any consumable or degradable item or

accessory including, but not limited to: plugs, cables, bat-

teries, light bulbs, fluorescent tubes and starters, covers

and filters, or replacement of any removable parts made of

glass or plastic.

10. Damage caused after delivery.

11. Water damage of any kind.

12. An Ariston Product not accessible to provide required

service.

13. Problems arising from other than defects in materials or

workmanship.

14. Travel time when installed in a recreational vehicle or

marine application.

This Warranty is void if the Ariston Product is altered, ser-

viced, maintained, dismantled, or otherwise interfered with

by any person who is not authorized by Ariston.

15. Labor when installed in a marine application.

16. Water leaks of any kind.

TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY

IS IN LIEU OF ALL OTHER WARRANTIES, WRITTEN

OR ORAL, WHETHER EXPRESSED BY AFFIRMATION,

PROMISE, DESCRIPTION, DRAWING, MODEL OR

SAMPLE. ANY AND ALL WARRANTIES OTHER THAN

THIS ONE, WHETHER EXPRESS OR IMPLIED, INCLUD-

ING IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY

DISCLAIMED. IMPLIED WARRANTIES INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS THAT CANNOT BE

EXCLUDED BY LAW, SHALL BE LIMITED TO THE SAME

DURATION AS THIS WARRANTY. EXCEPT FOR THAT

REPAIR OR REPLACEMENT AS DESCRIBED ABOVE,

ARISTON SHALL NOT BE LIABLE FOR ANY DIRECT, IN-

DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR SPECIFIC RELIEF.

Some States and Provinces do not allow the exclusion or

limitation of incidental or consequential damages and/or

implied warranties, so the above limitations or exclusions

may not apply to you. This Warranty gives you specific legal

rights and you may also have other legal rights which vary

from State to State or Province to Province.

Warranty

WHAT YOU SHOULD DO TO OBTAIN WARRANTY

SERVICE

All repairs or warranty service must by provided by Ariston

or an Authorized Ariston Service Center.

To schedule warranty service please call 1-800-356-0766,

email [email protected]. Please remember to

provide us with your Ariston Product’s model number and

serial number.

Please note that a copy of your original purchase receipt

showing the purchase date and the vendor’s name and ad-

dress are required to obtain service under this Warranty. If

the Ariston Product is located in an area where service by an

Authorized Ariston Service Center is not available, you may

be responsible for a trip charge or you may be required to

bring the Ariston Product to an Authorized Ariston Service

Center for service.

The foregoing are your sole (i.e., only) and exclusive rem-

edies under this Warranty. This Warranty is the only war-

ranty that Ariston is giving for this Ariston Product. This

Warranty replaces all other agreements and understand-

ings that you may have with Ariston or its representatives.

Ariston Washer User manual

Brand: Ariston

Model: Washer

Category: Washing machines

Type: User manual

This manual is also suitable for

Download PDF

report

Ariston Washer User manual

This manual is also suitable for

Ariston Washer User manual

Related papers