Casio LK200ES1A User manual

Brand: Casio

Model: LK200ES1A

Category: Digital pianos

Type: User manual

This manual is also suitable for

LK-200S

LK200ES1A

USER’S GUIDE

GUÍA DEL USUARIO

663A-E-002A

GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not applicable to other areas).

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Important!

Please note the following important information before using this product.

• Before using the optional AD-5 Adaptor to power the unit, be sure to check the AC Adaptor

for any damage first. Carefully check the power cord for breakage, cuts, exposed wire and

other serious damage. Never let children use an AC adaptor that is seriously damaged.

• Never attempt to recharge batteries.

• Do not use rechargeable batteries.

• Never mix old batteries with new ones.

• Use recommended batteries or equivalent types.

• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated

near the battery compartment.

• Replace batteries as soon as possible after any sign they are getting weak.

• Do not short-circuit the battery terminals.

• The product is not intended for children under 3 years.

• Use only CASIO AD-5 adaptor.

• The AC adaptor is not a toy.

• Be sure to disconnect the AC adaptor before cleaning the product.

CASIO Europe GmbH

Bornbarch 10, 22848 Norderstedt, Germany

This mark applies in EU countries only.

Declaration of Conformity

Model Number: LK-200S

Trade Name: CASIO COMPUTER CO., LTD.

Responsible party: CASIO, INC.

Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801

Telephone number: 973-361-5400

This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

E-1

663A-E-003A

Safety Precautions

Congratulations on your selection of the CASIO

electronic musical instrument.

• Before using the instrument, be sure to carefully

read through the instructions contained in this

manual.

• Be sure to keep all user documentation handy for

future reference.

Symbols

Various symbols are used in this user’s guide and on

the product itself to ensure that the product is used

safely and correctly, and to prevent injury to the user

and other persons as well as damage to property.

Those symbols along with their meanings are shown

below.

DANGER

This symbol indicates information that, if ignored

or applied incorrectly, creates the danger of death

or serious personal injury.

WARNING

This indication stipulates matters that have the risk

of causing death or serious injury if the product is

operated incorrectly while ignoring this indication.

CAUTION

This indication stipulates matters that have the risk

of causing injury as well as matters for which there

is the likelihood of occurrence of physical damage

only if the product is operated incorrectly while

ignoring this indication.

Symbol Examples

This triangle symbol ( ) means that the

user should be careful. (The example at

left indicates electrical shock caution.)

This circle with a line through it (

)

means that the indicated action must not

be performed. Indications within or

nearby this symbol are specifically

prohibited. (The example at left indicates

that disassembly is prohibited.)

The black dot (

) means that the

indicated action must be performed.

Indications within this symbol are actions

that are specifically instructed to be

performed. (The example at left indicates

that the power plug must be unplugged

from the electrical socket.)

E-2

DANGER

Alkaline Batteries

Perform the following steps immediately if

fluid leaking from alkaline batteries ever

gets into your eyes.

1. Do not rub your eyes! Rinse them with

water.

2. Contact your physician immediately.

Leaving alkaline battery fluid in your eyes

can lead to loss of sight.

WARNING

Smoke, Strange Odor, Overheating

Continued use of the product while it is

emitting smoke, a strange odor, or heat

creates the risk of fire and electric shock.

Take the following steps immediately.

1. Turn off power.

2. If you are using the AC adaptor for

power, unplug it from the wall outlet.

3. Contact your original retailer or an

authorized CASIO Service Provider.

AC Adaptor

● Misuse of the AC adaptor creates the

risk of fire and electric shock. Always

make sure you observe the following

precautions.

• Be sure to use only the AC adaptor

that is specified for this product.

• Use only a power source whose

voltage is within the rating marked on

the AC adaptor.

• Do not overload electrical outlets and

extension cords.

● Misuse of the AC adaptor’s electric cord

can damage or break it, creating the risk

of fire and electric shock. Always make

sure you observe the following

precautions.

• Never place heavy objects on the cord

or subject it to heat.

• Never try to modify the cord or subject

it to excessive bending.

• Never twist or stretch the cord.

• Should the electric cord or plug

become damaged, contact your

original retailer or authorized CASIO

Service Provider.

● Never touch the AC adaptor while your

hands are wet.

Doing so creates the risk of electric shock.

● Use the AC adaptor where it will not be

splashed with water. Water creates the

risk of fire and electric shock.

● Do not place a vase or any other container

filled with liquid on top of the AC

adaptor. Water creates the risk of fire

and electric shock.

Batteries

Misuse of batteries can cause them to leak,

resulting in damage to nearby objects, or to

explode, creating the risk of fire and

personal injury. Always make sure you

observe the following precautions.

• Never try to take batteries apart or allow

them to become shorted.

• Never expose batteries to heat or dispose

of them by incineration.

• Never mix old batteries with new ones.

• Never mix batteries of different types.

• Do not charge the batteries.

• Make sure the positive (+) and negative

(–) ends of the batteries are facing

correctly.

Do not incinerate the product.

Never throw the product into fire.

Doing so can cause it to explode, creating

the risk of fire and personal injury.

Water and Foreign Matter

Water, other liquids, and foreign matter

(such as pieces of metal) getting into the

product create the risk of fire and electric

shock. Take the following steps

immediately.

1. Turn off power.

2. If you are using the AC adaptor for

power, unplug it from the wall outlet.

3. Contact your original retailer or an

authorized CASIO Service Provider.

Disassembly and Modification

Never try to take this product apart or

modify it in any way. Doing so creates the

risk of electric shock, burn injury, or other

personal injury. Leave all internal

inspection, adjustment, and maintenance up

to your original retailer or authorized

CASIO Service Provider.

Safety Precautions

663A-E-004A

E-3

Dropping and Impact

Continued use of this product after it has

been damaged by dropping or subjecting it

to strong impact creates the risk of fire and

electric shock. Take the following steps

immediately.

1. Turn off power.

2. If you are using the AC adaptor for

power, unplug it from the wall outlet.

3. Contact your original retailer or an

authorized CASIO Service Provider.

Plastic Bags

Never place the plastic bag the product

comes in over your head or in your mouth.

Doing so creates the risk of suffocation.

Particular care concerning this precaution

is required where small children are

present.

Keep off of the product and stand.*

Climbing onto the product or stand can

cause it to tip over or become damaged.

Particular care concerning this precaution

is required where small children are

present.

Location

Avoid locating the product on an unstable

stand, on an uneven surface, or any other

unstable location. An unstable location can

cause the product to fall over, creating the

risk of personal injury.

CAUTION

AC Adaptor

● Misuse of the AC adaptor creates the

risk of fire and electric shock. Always

make sure you observe the following

precautions.

• Do not locate the electric cord near a

stove or other sources of heat.

• Never pull on the cord when

unplugging from the electrical outlet.

Always grasp the AC adaptor when

unplugging.

● Misuse of the AC adaptor creates the

risk of fire and electric shock. Always

make sure you observe the following

precautions.

• Insert the AC adaptor into the wall

outlet as far as it will go.

• Unplug the AC adaptor from the wall

outlet during lightening storms or

before leaving on a trip or other long-

term absence.

• At least once a year, unplug the AC

adaptor from the wall outlet and wipe

away any dust that is built up in the

area around the prongs of the plug.

Relocating the Product

Before relocating the product, always

unplug the AC adaptor from the wall outlet

and disconnect all other cables and

connecting cords. Leaving cords connected

creates the risk of damage to the cords, fire,

and electric shock.

Cleaning

Before cleaning the product, always unplug

the AC adaptor from the wall outlet first.

Leaving the AC adaptor plugged in creates

the risk of damage to the AC adaptor, fire,

and electric shock.

Batteries

Misuse of batteries can cause them to leak

resulting in damage to nearby objects, or to

explode, creating the risk of fire and

personal injury. Always make sure you

observe the following precautions.

• Use only batteries that are specified for

use with this product.

• Remove batteries from the product if you

do not plan to use it for a long time.

Safety Precautions

663A-E-005A

E-4

• Should you ever feel any symptoms

similar to those described above when

using this product, stop using it

immediately and contact your physician.

Heavy Objects

Never place heavy object on top of the

product.

Doing so can make the product top heavy,

causing the product to tip over or the object

to fall from it, creating the risk of personal

injury.

Correct Stand* Assembly

An incorrectly assembled stand can tip over,

causing the product to fall and creating the

risk of personal injury.

Make sure you assemble the stand correctly,

following the assembly instructions that

come with it. Make sure you mount the

product on the stand correctly.

* Stand is available as an option.

IMPORTANT!

When using batteries, be sure to replace them or shift to

one of the alternate power sources whenever you notice

any of the following symptoms.

• Dim power supply indicator

• Instrument does not turn on

• Dim, difficult to read display

• Abnormally low speaker/headphone volume

• Distortion of sound output

• Occasional interruption of sound when playing at high

volumes

• Sudden power failure when playing at high volumes

• Dimming of the display when playing at high volume

• Continued sound output even after you release a key

• A totally different tone may sound

• Abnormal rhythm pattern and demo tune play

• Abnormally low microphone volume

• Distortion of microphone input

• Dim power supply indicator when a microphone is used

• Sudden power failure when using the microphone

• Dimming of keyboard lights when notes sound

• Loss of power, sound distortion, or low volume when

playing from a connected computer

Connectors

Connect only the specified devices and

equipment to the product’s connectors.

Connection of a non-specified device or

equipment creates the risk of fire and

electric shock.

Location

Avoid the following locations for this

product. Such locations create the risk of

fire and electric shock.

• Areas subject to high humidity or large

amounts of dust.

• In food preparation areas or other areas

subject to oil smoke.

• Near air conditioning equipment, on a

heated carpet, in areas exposed to direct

sunlight, inside of a vehicle parked in

the sun, or any other area that subjects

the product to high temperatures.

Display Screen

• Never push on the display screen’s LCD

panel or subject it to strong impact. Doing

so can cause the LCD panel’s glass to

crack, creating the risk of personal injury.

• Should the LCD panel ever crack or

break, never touch the liquid inside of

the panel. LCD panel liquid can cause

skin irritation.

• Should LCD panel liquid ever get inside

your mouth, immediately wash out your

mouth with water and contact your

physician.

• Should LCD panel liquid ever get into

your eyes or onto your skin, rinse with

clear water for at least 15 minutes, and

then contact a physician.

Sound Volume

Do not listen to music at very loud volumes

for long periods. Particular care concerning

this precaution is required when using

headphones. High volume settings can

damage your hearing.

Health Precaution

In extremely rare cases, exposure to strong

sudden light or flashing light can cause

momentary muscle spasms, loss of

consciousness, or other physical problems

with some individuals.

• If you suspect that you might be

susceptible to any condition such as this,

be sure to consult with your physician

before using this product.

• Use this product in an area that is well

illuminated.

Safety Precautions

663A-E-006A

E-5

❐ 264 tones

A wide selection of tones includes stereo piano and synthesized sounds, drum sets, and much more.

Other features include digital effects that control the acoustical characteristic of tones.

❐ PIANO BANK button

The touch of a button takes you directly to piano tones and piano lessons.

❐ 3-Step Lesson System

The 3-Step Lesson System lets you practice at your own pace. The keyboard automatically grades your performances, so you can

trace your progress as you improve.

• 3-Step Lesson System: Use any of the keyboard’s built-in tunes and SMF data from a memory card to learn to play as the

keyboard keys light to teach you the correct notes. First practice the timing of the notes. Next, play along at your own pace.

Soon you will be ready for step three, where you play along at normal speed.

* Note that key lights may be difficult to see under direct sunlight or under other very bright lighting.

• Evaluation System: The keyboard can be configured to rate your performances during Step 3 lesson by assigning points.

❐ 100 built-in tunes, including piano pieces

Built-in tunes are divided into two groups: a Song Bank of 65 tunes with Auto Accompaniment, and a Piano Bank of 35 piano

tunes. You can simply enjoy listening to the built-in tunes, or eliminate either hand part of a tune, and then play along on the

keyboard.

❐ 120 rhythms

A selection of rhythms cover rock, pops, jazz and just about any other musical style imaginable.

❐ Auto Accompaniment

Simply play a chord and the corresponding rhythm, bass, and chord parts play along automatically.

❐ Musical Information System

A big LCD screen graphically shows you fingerings and notes, making keyboard play more informative and enjoyable than ever

before.

❐ Storing and Playing Back Tune Data You Transferred from Your Computer

You can connect your keyboard to a computer, use special CASIO conversion software to convert SMF data you purchase or

create to CASIO format, and then transfer it to the keyboard.

❐ Memory Card Slot

You can load a card with a standard MIDI file (SMF) and play it back on the keyboard.

Main Features

663A-E-007A

E-6

663A-E-008A

Contents

Safety Precautions .................... E-1

Main Features ............................ E-5

General Guide............................ E-8

Attaching the Score Stand ..................... E-10

Quick Reference .......................E-11

To play the keyboard .............................. E-11

Power Supply .......................... E-12

Using batteries ....................................... E-12

Using the AC Adaptor ............................. E-13

Auto Power Off ....................................... E-13

Power On Alert ....................................... E-14

Memory Contents ................................... E-14

Connections ............................ E-14

Phones/Output Jack ............................... E-14

USB port ................................................ E-15

Sustain/Assignable Jack ........................ E-15

Microphone Jack .................................... E-15

Accessories and Options ....................... E-15

Basic Operations..................... E-16

To play the keyboard .............................. E-16

Selecting a Tone..................................... E-16

Using Tone Effects ................................. E-17

Turning the Key Light System

On and Off.............................................. E-17

Using the Microphone Jack .................... E-17

Playing a Built-in Tune............ E-18

To play back a Song Bank tune ............. E-18

To play back a Piano Bank tune............. E-19

Musical Information System ................... E-19

Adjusting the Tempo............................... E-19

To pause playback ................................. E-20

To fast reverse ....................................... E-20

To fast forward ....................................... E-20

Looping a Musical Phrase ...................... E-20

To change the melody tone .................... E-21

To play all tunes in succession ............... E-21

Using the PIANO BANK Button ............. E-21

Using the SMF Data on the

Bundled CD-ROM .................................. E-21

3-Step Lesson.......................... E-22

Evaluation Mode .................................... E-23

Using the Lesson Functions and

Evaluation Mode .................................... E-24

Step 1 – Master the timing. .................... E-24

Step 2 – Master the notes. ..................... E-24

Step 3 – Play at normal speed. .............. E-25

Voice Fingering Guide ............................ E-26

Using the Metronome ............................. E-26

E-7

Contents

663A-E-009A

Company and product names used in this

manual may be registered trademarks of

others.

Auto Accompaniment ............. E-27

Selecting a Rhythm ................................ E-27

Playing a Rhythm ................................... E-28

Using Auto Accompaniment ................... E-28

Using an Intro Pattern ............................ E-30

Using a Fill-in Pattern ............................. E-30

Using a Rhythm Variation....................... E-30

Using a Fill-in Pattern with a Variation

Rhythm ................................................... E-31

Synchro Starting Accompaniment with

Rhythm Play ........................................... E-31

Finishing with an Ending Pattern ........... E-31

Keyboard Settings .................. E-32

Adjusting Accompaniment and

Song Bank Volume ................................ E-32

Transposing the Keyboard ..................... E-33

Tuning the Keyboard .............................. E-33

Connection to a Computer ..... E-34

Connecting to a Computer ..................... E-34

Expanding the Selections in the

Song Bank Tunes ................................... E-35

General MIDI Tone ................................. E-36

Changing the Settings ............................ E-36

Using a Memory Card ............. E-38

Getting Ready ........................................ E-39

Reading a Memory Card ........................ E-40

Memory Card Error Messages ............... E-41

Troubleshooting ...................... E-43

Specifications .......................... E-45

Care of your keyboard ............ E-46

Appendix .................................... A-1

Tone List / Note Table............................... A-1

Drum Assignment List .............................. A-4

FINGERED Chord Chart .......................... A-5

Rhythm List .............................................. A-6

Song List .................................................. A-7

MIDI messages that can be sent

and received using the USB port

E-8

663A-E-010A

KJI L M N P

U V W X Y Z \[

1 3

2 4

9 0 A B C D F G HE

5 76

R S

General Guide

E-9

General Guide

MIC VOLUME slider

Power indicator

POWER/MODE switch

MAIN VOLUME slider

FUNCTION button

REVERB/CHORUS button

KEY LIGHT button

● SONG/PIANO BANK/RHYTHM CONTROLLER

REPEAT button, INTRO button

REW button, NORMAL/FILL-IN button

FF button, VARIATION/FILL-IN button

PAUSE button, SYNCHRO/ENDING button

PLAY/STOP button, START/STOP button

Rhythm controller indicator

Song/Piano Bank controller indicator

TEMPO buttons

SONG BANK button

PIANO BANK button

CARD button

Percussion instrument list

CHORD root names

Speaker

RHYTHM list

TONE list

SONG BANK list

Display

PIANO BANK list

Voice 1 to 5 list

TONE button

RHYTHM button

DATA ACCESS lamp

● 3-STEP LESSON

STEP 1 button

STEP 2 button

STEP 3 button

SCORING button

LEFT button

RIGHT button

[

METRONOME button

SPEAK button

663A-E-011A

Controller Indicators

Song/Piano Bank controller indicator

Pressing the SONG BANK or PIANO BANK button causes the Song/Piano Bank controller indicator to light. This indicates that

buttons 8 through B are currently functioning as playback control buttons.

Rhythm controller indicator

Pressing the RHYTHM button to enter the Rhythm Mode causes the Rhythm controller indicator to light. This indicates that

buttons 8 through B are currently functioning as rhythm control buttons.

NOTE

• Display examples shown in this User’s Guide are intended for illustrative purposes only. The actual text and values that

appear on the display may differ from the examples shown in this User’s Guide.

• Viewing a liquid crystal display screen from an angle can change the appearance of display contrast. The display contrast of

this keyboard is set to allow easy viewing for a person seated on a chair in front of the keyboard. Note that display contrast

is fixed, and cannot be adjusted.

E-10

General Guide

Rear Panel

c d e

SUSTAIN/ASSIGNABLE JACK

DC 9V jack

PHONES/OUTPUT jack

663A-E-012A

]

[+]

[–]

buttons

Number buttons

• Negative values cannot be

input using the number

buttons. Use [+] (increase)

and [–] (decrease) instead.

• For input of numbers to

change a displayed number

or setting.

SD CARD SLOT

USB port

*1 Attaching the Score Stand

Insert both ends of the music stand provided

with the keyboard into the two holes on the

top surface.

MIC IN jack

E-11

Quick Reference

This section provides a quick overview of keyboard operation

using steps one and two of the 3-step lesson feature.

To play the keyboard

Set the POWER/MODE switch to NORMAL.

• This causes the power indicator to light.

Press the SONG BANK button.

Find the tune you want to play in the SONG BANK

List, and then use the number buttons to input its

two-digit number.

• See page A-7 for the SONG BANK List.

Example: To select “54 ALOHA OE”, input 5 and then

Press the STEP 1 button or STEP 2 button.

• The keyboard sounds a count beat and waits for you

to play something on the keyboard. The keys that you

need to press first flash.

Play the melody along with the selected tune’s

accompaniment.

• Play in accordance with the fingerings, notes, and

dynamic marks that appear on the display.

Aloha

Indicator appears

Aloha

FingeringNote pitch

663A-E-013A

PIANO BANK

SONG BANKPOWER/MODE

Number buttons

PLAY/STOP

STEP1

STEP2

Power indicator

Lit

E-12

If you selected lesson Step 1

• Play the notes on the keyboard.

• Accompaniment (left-hand part) plays in time with

the notes.

• With Step 1, the correct melody note is played no

matter which keyboard key you press.

If you selected lesson Step 2

• Play the correct notes on the keyboard.

• Press the keyboard key that lights. Note that with a

Piano Bank tune, the keyboard key light turns off as

soon as you press the key.

• The keyboard key for the next note you will need to

play flashes.

• Accompaniment (left-hand part) plays in time with

the notes, as long as you press the correct keyboard

keys.

To stop play at any time, press the PLAY/STOP

button.

To play an Etude or Concert Piece tune

When you get to step 2 of the above procedure,

press the PIANO BANK button in place of the

SONG BANK button.

Find the tune you want to play in the PIANO BANK

List, and then use the number buttons to input its

two-digit number.

• See page A-7 for the PIANO BANK List.

Next, continue from step 4 of the above procedure.

Quick Reference

Indicator appears

663A-E-014A

Power Supply

This keyboard can be powered by current from a standard

household wall outlet (using the specified AC adaptor) or by

batteries. Always make sure you turn the keyboard off

whenever you are not using it.

Using batteries

Always make sure you turn off the keyboard before loading

or replacing batteries.

To load batteries

Remove the battery compartment cover.

Load 6 AA-size batteries into the battery

compartment.

• Make sure that the positive (+) and negative (–) ends

are facing correctly.

Insert the tabs on the battery compartment cover

into the holes provided and close the cover.

NOTE

• The keyboard may not function correctly if you load or

replace batteries with power turned on. If this happens,

turning the keyboard off and then back on again should

return functions back to normal.

Important Battery Information

■ The following shows the approximate battery life.

Manganese batteries ............................... 1 hour

Alkaline batteries .................................... 4 hours

The above value is standard battery life at normal

temperature, with the keyboard volume at medium

setting. Temperature extremes or playing at very loud

volume settings can shorten battery life.

E-13

WARNING

Misuse of batteries can cause them to leak, resulting in

damage to nearby objects, or to explode, creating the risk of

fire and personal injury. Always make sure you observe the

following precautions.

• Never try to take batteries apart or allow them to

become shorted.

• Never expose batteries to heat or dispose of them by

incineration.

• Never mix old batteries with new ones.

• Never mix batteries of different types.

• Do not charge the batteries.

• Make sure the positive (+) and negative (–) ends of

the batteries are facing correctly.

CAUTION

Misuse of batteries can cause them to leak resulting in

damage to nearby objects, or to explode, creating the risk of

fire and personal injury. Always make sure you observe the

following precautions.

• Use only batteries that are specified for use with this

product.

• Remove batteries from the product if you do not plan

to use it for a long time.

Using the AC Adaptor

Make sure that you use only the AC adaptor specified for

this keyboard.

Specified AC Adaptor: AD-5

[Rear Panel]

663A-E-015A

DC 9V jack

AC adaptor AD-5

AC outlet

Power Supply

Note the following important precautions to avoid damage

to the power cord.

● During Use

• Never pull on the cord with excessive force.

• Never repeatedly pull on the cord.

• Never twist the cord at the base of the plug or connector.

• The power cord should not be stretched tight while it is

in use.

● During Movement

• Before moving the keyboard, be sure to unplug the AC

adaptor from the power outlet.

● During Storage

• Loop and bundle the power cord, but never wind it

around the AC adaptor.

IMPORTANT!

• Make sure that the keyboard is turned off before

connecting or disconnecting the AC adaptor.

• Using the AC adaptor for a long time can cause it to

become warm to the touch. This is normal and does not

indicate malfunction.

Auto Power Off

When you are using battery power, keyboard power turns

off automatically whenever you leave it on without

performing any operation for about 6 minutes. When this

happens, adjust the POWER/MODE switch to turn power

back on.

NOTE

• Auto Power Off is disabled (it does not function) when

you are using the AC adaptor to power the keyboard.

To disable Auto Power Off

Hold down the TONE button while turning on the keyboard

to disable Auto Power Off.

NOTE

• When this function is turned off, the keyboard does not

turn off automatically no matter how long it is left with

no operation being performed.

• Auto Power Off is enabled again when you manually

turn off power and then turn it back on again.

E-14

Power Supply

663A-E-016A

Power On Alert

Keyboard keys light to alert you if you leave power on and

do not perform any operation for about 6 minutes. Note that

keys light only, and no sound is produced. When this

happens, press any button or keyboard key to clear the power

on alert.

NOTE

• Power on alert operates only when you are powering

the keyboard using the AC adaptor. It does not operate

when you are using batteries.

To turn off power on alert

Press the FUNCTION button a number of times until

“DEMO 2” appears on the display.

Use the [+] and [–] buttons to change the setting to

“oFF”.

Press the FUNCTION button to clear the setting

screen from the display.

Memory Contents

Even when the keyboard is turned off, user song data saved

as Song Bank tunes are retained as long as power is being

supplied to the keyboard.

Unplugging the AC adaptor when batteries are not loaded

or when batteries are dead cuts off the power supply. This

causes all keyboard settings to be initialized to the initial

factory defaults, and clears all data stored in memory.

Power Requirements

Note the following precautions whenever you want to ensure

that current keyboard settings and memory contents are not

lost.

• Make sure the keyboard is being supplied power through

the AC adaptor before replacing its batteries.

• Before unplugging the AC adaptor, make sure that fresh

batteries are loaded in the keyboard.

Make sure that keyboard power is turned off before replacing

batteries or unplugging the AC adaptor.

Connections

Phones/Output Jack

PREPARATION

• Before connecting headphones or other external

equipment, be sure to first turn down the volume settings

of the keyboard and the connected equipment. You can

then adjust volume to the desired level after connections

are complete.

[Rear Panel]

White

Red

PIN plug

Stereo standard plug

Audio connection

PHONES/OUTPUT jack

Keyboard amp,

guitar amp, etc.

LEFT

RIGHT

AUX IN or similar terminal

of audio amplifier

Connecting Headphones (Figure

)

Connecting headphones cuts off output from the keyboard’s

built-in speakers, so you can play even late at night without

disturbing anyone.

Audio Equipment (Figure

)

Connect the keyboard to an audio equipment using a

commercially available connecting cord with a standard plug

on one end and two PIN plugs on the other end. Note that

the standard plug you connect to the keyboard must be a

stereo plug, otherwise you will be able to output only one of

stereo channels. In this configuration, you normally set the

input selector of the audio equipment to the terminal (usually

marked AUX IN or something similar) where the cord from

the keyboard is connected. See the user documentation that

comes with your audio equipment for full details.

Musical Instrument Amplifier (Figure

)

Use a commercially available connecting cord to connect the

keyboard to a musical instrument amplifier.

NOTE

• Be sure to use a connecting cord that has a stereo

standard plug on the end you connect to the keyboard,

and a connector that provides dual channel (left and

right) input to the amplifier to which you are connecting.

The wrong type of connector at either end can cause

one of the stereo channels to be lost.

When connected to a musical instrument amplifier, set the

volume of the keyboard to a relatively low level and make

output volume adjustments using the amplifier’s controls.

E-15

Connection Example

USB port

You can also connect the keyboard to a computer. See

“Connecting to a Computer” on page E-34 for details.

Sustain/Assignable Jack

You can connect an optional sustain pedal (SP-3 or SP-20) to

the SUSTAIN/ASSIGNABLE JACK to enable the capabilities

described below.

For details on how to select the pedal function you want, see

“SUSTAIN/ASSIGNABLE JACK (Default: SUS)” on page

E-37.

SP-20

SUSTAIN/ASSIGNABLE JACK

Sustain Pedal

• With piano tones, depressing the pedal causes notes to

linger, much like a piano’s damper pedal.

• With organ tones, depressing the pedal causes notes to

continue to sound until the pedal is released.

Sostenuto Pedal

• As with the sustain pedal function described above,

depressing the sostenuto pedal causes notes to be sustained.

• This difference between a sostenuto pedal and sustain pedal

is the timing. With a sostenuto pedal, you press the keys

and then depress the pedal before you release the keys.

• Only the notes that are sounding when the pedal is

depressed are sustained.

Soft Pedal

Depressing the pedal softens the sound of the notes being

played.

Rhythm Start/Stop Pedal

In this case, the pedal performs the same functions as the

START/STOP button.

INPUT 1

INPUT 2

PIN jack

PIN plug (red)

PIN plug (white)

Stereo standard plug

Keyboard or

guitar amp

To keyboard’s

PHONES/OUTPUT

ack

Standard plug

663A-E-017A

Connections

Microphone Jack

You can connect a commercially available microphone to the

microphone jack and sing along with notes played on the

keyboard. For details, see “Using the Microphone Jack” on

page E-17.

Accessories and Options

Use only the accessories and options specified for this

keyboard. Use of non-authorized items creates the danger of

fire, electrical shock, and personal injury.

E-16

Basic Operations

This section provides information on performing basic

keyboard operations.

To play the keyboard

Set the POWER/MODE switch to NORMAL.

Use the MAIN VOLUME slider to set the volume

to a relatively low level.

Play something on the keyboard.

Selecting a Tone

This keyboard comes with 264 built-in tones. Use the

following procedure to select the tone you want.

To select a tone

Find the tone you want to use in the TONE List and

note its tone number.

• Not all of the available tones are shown on the tone

list printed on the keyboard console. For a complete

list, see the “Tone List” on page A-1.

Press the TONE button.

Use the number buttons to input the three-digit tone

number of the tone you want to select.

Example: To select “049 ACOUSTIC BASS”, input 0, 4

and then 9.

NOTE

• Always input all three digits for the tone number,

including leading zeros (if any). If you input one or two

digits and stop, the display will automatically clear your

input after a few seconds.

• You can also increment the displayed tone number by

pressing [+] and decrement it by pressing [–].

• When one of the drum sets is selected (tone numbers

256 through 263), each keyboard key is assigned a

different percussion sound. See page A-4 for details.

Polyphony

The term polyphony refers to the maximum number of notes

you can play at the same time. The keyboard has 32-note

polyphony, which includes the notes you play as well as the

rhythms and auto-accompaniment patterns that are played

by the keyboard. This means that when a rhythm or auto-

accompaniment pattern is being played by the keyboard, the

number of notes (polyphony) available for keyboard play is

reduced. Also note that some of the tones offer only 16-note

polyphony.

• When rhythm or auto accompaniment is playing, the

number of sounds simultaneously played is reduced.

Aco .B

Indicator appears

663A-E-018A

MIC VOLUME

Number buttonsKEY LIGHT

POWER/MODE [+] / [–]

MAIN VOLUME TONEREVERB/CHORUS

E-17

Using Tone Effects

Reverb: Makes your notes resonate

Chorus: Adds more breadth to your notes

Press the REVERB/CHORUS button to cycle through

the effect settings as shown below.

• You can find out the current effect setting by looking

at the REVERB and CHORUS indicators.

After turning on the effect you want, use the number

buttons or the [+]/[–] buttons to select the effect

type you want.

• Note that you need to select an effect type with the

number buttons or the [+]/[–] buttons within a few

seconds after turning on an effect. If you don’t, the

display will exit the setting screen.

Effect List

Turning the Key Light System On

and Off

Use the following procedure when you want to turn the key

light system on or off.

To turn the key light system on and off

Press the KEY LIGHT button to toggle the key light

system on and off.

• The KEY LIGHT indicator disappears when the key

light system is turned off.

NOTE

• The key light system is turned on automatically whenever

you turn on keyboard power.

Basic Operations

663A-E-019A

Using the Microphone Jack

Connecting a commercially available microphone to the MIC

IN jack makes it possible to sing along with the keyboard’s

built-in tunes or with SMF playback. When connecting a

microphone, be sure to first adjust the MIC VOLUME to a

relatively low setting, and then adjust to the level you want

after connecting.

Set the MIC VOLUME slider setting so it is on the

“MIN” side.

Turn on the microphone’s on/off switch.

Use the MIC VOLUME slider to adjust microphone

volume to the level you want.

[Rear Panel]

IMPORTANT!

• Be sure to use the microphone’s on/off switch to turn off

the microphone and to disconnect the microphone from

the keyboard whenever you are not using it.

Recommended Microphone Type

• Dynamic microphone (standard plug)

IMPORTANT!

• Be sure to disconnect the microphone from the keyboard

whenever you are not using it.

Howling (Feedback Noise)

Any of the following conditions can cause howling (feedback

noise).

• Covering the head of the microphone with your hand

• Positioning the microphone too near to a speaker

Should howling occur, try grasping the microphone further

away from the head, and move away from any nearby

speaker.

Static Noise

Fluorescent lighting can cause static noise in the microphone

signal. When this happens, move away from the lighting you

suspect may be causing the static.

MIC VOLUME slider

Microphone

Microphone on/off switch

Chorus 0: Chorus 1

1: Chorus 2

2: Chorus 3

3: Chorus 4

Reverb 0: Room 1

1: Room 2

2: Hall 1

3: Hall 2

On On On Off

Reverb on Chorus on Both on Both off

E-18

Playing a Built-in Tune

Your keyboard comes with a total of built-in 100 tunes. You

can play back built-in tunes for your own listening pleasure,

or you can use them for practice and even sing-along. Built-

in tunes are divided between the two groups described below.

• Song Bank Group: 65 tunes

The tunes in this group are Auto Accompaniment tunes.

• Piano Bank Group: 35 tunes

The piano tunes in this group are subdivided between 10

etudes and 25 concert pieces.

In addition to the built-in tunes, you can also play back the

tunes you download over the Internet (page E-35).

To play back a Song Bank tune

PREPARATION

• Adjust the main volume (page E-16).

Find the tune you want to play in the SONG BANK

List, and note its number.

• See page A-7 for the SONG BANK List.

Press the SONG BANK button to enter the Song

Bank Mode.

Use the number buttons to input the tune’s two-

digit number.

Example: To select “54 ALOHA OE”, input 5 and then 4.

NOTE

• Tune Number 00 is the initial default Song Bank tune

setting whenever you turn on keyboard power.

• You can also increment the displayed tune number by

pressing [+] and decrement is by pressing [–].

Press the PLAY/STOP button to start play of the tune.

Press the PLAY/STOP button to stop playback of

the Song Bank tune.

• The tune you select continues to play until you stop

it.

Indicator appears

Aloha

Song number Song name

663A-E-020A

PIANO BANK

SONG BANK

Number buttons

PLAY/STOPPAUSE

TEMPOFF

REPEAT

REW

[+] / [–]

TONE

Aloha

Fingering

Staff display

Chord name

Page is loading ...

Casio LK200ES1A User manual

Brand: Casio

Model: LK200ES1A

Category: Digital pianos

Type: User manual

This manual is also suitable for

LK-200S

Download PDF

report

Casio LK200ES1A User manual

This manual is also suitable for

Casio LK200ES1A User manual

Related papers

Other documents