Brada Appliances MPN1-10CR User manual

Brand
Brada Appliances
Model
MPN1-10CR
Category
Split-system air conditioners
Type
User manual

This manual is also suitable for

Brada Appliances MPN1-10CR is a portable air conditioner suitable for use in medium-sized rooms. It features an electronic control panel with an LED display that shows the set temperature and timer settings. The unit can be controlled remotely using the included remote controller.

The MPN1-10CR has four fan speeds (low, medium, high, and auto) and three operating modes: cool, dry, and fan only. The sleep mode gradually increases the temperature by 1 degree Celsius or 2 degrees Fahrenheit every 30 minutes for the first hour, then maintains the new temperature for 7 hours before returning to the original setting.

Brada Appliances MPN1-10CR is a portable air conditioner suitable for use in medium-sized rooms. It features an electronic control panel with an LED display that shows the set temperature and timer settings. The unit can be controlled remotely using the included remote controller.

The MPN1-10CR has four fan speeds (low, medium, high, and auto) and three operating modes: cool, dry, and fan only. The sleep mode gradually increases the temperature by 1 degree Celsius or 2 degrees Fahrenheit every 30 minutes for the first hour, then maintains the new temperature for 7 hours before returning to the original setting.

PORTABLEAIRCONDITIONER
Insideyouwillfindmanyhelpfulhintsonhowtouseandmaintainyourairconditionerproperly.Just
alittlepreventativecareonyourpartcansaveyouagreatdealoftimeandmoneyoverthelifeof
yourairconditioner.Beforeoperatingthisproduct,pleasereadtheinstructionscarefullyandsavethis
manualforfutureuse.
Model:MPN1-08CR
MPN1-10CR
CONTENTS
The rating data indicated on the rating label is based
on the testing condition of installing the un-extended
air exhaust duct without adaptor (The duct and the
adaptor are listed in the accessories chart of the
InstructionManual).
NOTE
1
SAFETY PRECAUTIONS
Safety rules ........................................................................................................................................2
Electrical information ..........................................................................................................................2
Accessories ........................................................................................................................................3
Names of parts....................................................................................................................................4
Electronic control operating instructions ............................................................................................5
Operating instructions ........................................................................................................................9
Location ............................................................................................................................................11
Window kit installation ......................................................................................................................11
Exhaust hose installation ..................................................................................................................14
Care and maintenance .....................................................................................................................15
Troubleshooting ................................................................................................................................16
AIR CONDITIONER FEATURES
CARE AND MAINTENANCE
TROUBLESHOOTING TIPS
OPERATING INSTRUCTIONS
INSTALLATION INSTRUCTIONS
IDENTIFICATION OF PARTS
Operating condition .......................................................................................................................10
Remote controller illustration ............................................................................................................17
REMOTE CONTROLLER ILLUSTRATION
2
Topreventinjurytotheuserorotherpeopleandpropertydamage,thefollowinginstructionsmustbe
followed.Incorrectoperationduetoignoringofinstructionsmaycauseharmordamage.
Yourairconditionershouldbeusedinsuchaway
thatitisprotectedfrommoisture.e.g.condensation,
splashedwater,etc.Donotplaceorstoreyourair
conditionerwhereitcanfallorbepulledintowater
oranyotherliquid.Unplugimmediately.
Alwaystransportyourairconditionerinavertical
positionandstandonastable,levelsurfaceduring
use.
Turnofftheproductwhennotinuse.
Alwayscontactaqualifiedpersontocarryout
repairs.Ifthesupplycordisdamageditmustbe
repairedbyaqualifiedrepairer.
Keepanairpathofatleast30cm(0.98ft)allaround
theunitfromwalls,furnitureandcurtains.
Iftheairconditionerisknockedoverduringuse,
turnofftheunitandunplugfromthemainssupply
immediately.
SAFETY PRECAUTIONS
!
Alwaysdothis
Donotoperateyourairconditionerinawetroom
suchasabathroomorlaundryroom.
Donottouchtheunitwithwetordamphandsor
whenbarefoot.
Donotpressthebuttonsonthecontrolpanelwith
anythingotherthanyourfingers.
Donotremoveanyfixedcovers.Neverusethis
applianceifitisnotworkingproperly,orifithas
beendroppedordamaged.
Neverusetheplugtostartandstoptheunit.
Alwaysusetheswitchonthecontrolpanel.
Donotcoverorobstructtheinletoroutletgrilles.
Donotusehazardouschemicalstocleanorcome
intocontactwiththeunit.Donotusetheunitinthe
presenceofinflammablesubstancesorvapoursuch
asalcohol,insecticides,petrol,etc.
Donotallowchildrentooperatetheunit
unsupervised.
Donotusethisproductforfunctionsotherthan
thosedescribedinthisinstructionmanual.
Neverdothis
EnergySave
Usetheunitintherecommendedroomsize.
Locatetheunitwherefurniturecannotobstructtheairflow.
Keepblinds/curtainsclosedduringthesunniestpartoftheday.
Keepthefiltersclean.
Keepdoorsandwindowsclosedtokeepcoolairinandwarmairout.
Besuretheelectricalserviceisadequateforthemodelyouhavechosen. Thisinformationcanbefound
ontheserialplate,whichislocatedonthesideofthecabinetandbehindthegrille.
Besuretheairconditionerisproperlygrounded. Tominimizeshockandfirehazards,propergroundingis
important. Thepowercordisequippedwithathree-pronggroundingplugforprotectionagainstshock
hazards.
Yourairconditionermustbeusedinaproperlygroundedwallreceptacle.Ifthewallreceptacleyouintend
touseisnotadequatelygroundedorprotectedbyatimedelayfuseorcircuitbreaker,haveaqualified
electricianinstalltheproperreceptacle.
Ensurethereceptacleisaccessibleaftertheunitinstallation.
WARNING
Foryoursafety
Donotstoreorusegasolineorotherflammablevaporsandliquidsinthevicinityofthisoranyother
appliance.
Avoidfirehazardorelectricshock.
Donotremoveanyprongfromthepowercord.
Donotuseanextensioncordoranadaptorplug.
WARNING
ElectricalInfor mation
Safetyrules
Accessories
Checkalltheaccessoriesareincludedinthepackageandpleaserefertotheinstallation
instructionsfortheirusage.
Suggestedtoolsforwindowkitinstallation
1.Screwdriver(mediumsizePhillips)
2. Tapemeasureorruler
3.Knifeorscissors
4.Saw(Intheeventthatthewindowkitneedstobecutdowninsizebecause
thewindowistoonarrowfordirectinstallation)
IDENTIFICATION OF PARTS
O
F
3
IDENTIFICATION OF PARTS
NAMESOFPARTS
FRONTVIEW
OperationPanel
HorizontalLouvers
Caster
CarryingHandle
(bothsides)
1
2
3
4
1
2
3
4
Fig.1
5
6
7
8
9
10
Upper AirFilter
(Behindthegrille)
AirOutlet
Powercordoutlet
DrainOutlet
Airintake
Airintake
Lower AirFilter
(Behindthegrille)
BottomDrainPlug
11
Fig.2
8
5
6
7
9
10
11
12
12
REARVIEW
BeforeUsing This AirConditioner,beSure ToCheck TheBack
Of TheUnit ToMakeSure That TheLowerDrainPlugIsSecurity
InPlace.SeeFig.2
12
4
5
AIR CONDITIONER FEATURES
Beforeyoubegin,thoroughlyfamiliarizeyourselfwiththecontrolpanelandremotecontroller
andallfunctions,thenfollowthesymbolforthefunctionsyoudesire.
Theunitcanbecontrolledbytheunitcontrolpanelaloneorwiththeremotecontroller.
ELECTRONICCONTROLOPERATINGINSTRUCTIONS
Fig.3
OPERATIONPANELOFTHEAIRCONDITIONER
3
4
5
7
1
6
POWERbutton
AUTO COOL
DRY
FAN
MODE
SLEEP FAN
HI
MED
LOW
TIMERON
TIMEROFF
F
C
SWING
1
2
8
SLEEP
FAN
HI
MED
LOW
TIMERON
TIMEROFF
F
C
NOTE:
Powerswitchon/off.
SLEEPbutton
SLEEP
FAN
HI
MED
LOW
TIMERON
TIMEROFF
F
C
Pressthisbutton,theselectedtemperature
willincrease(cooling)by1 30minutes.
Thetemperaturewillthenincrease(cooling)
byanother afteranadditional30
minutes.
Thisnewtemperaturewillmaintainfor
7hoursbeforeitreturnstotheoriginally
selectedtemperature.Thentheunitwillcontinue
tooperateasoriginallyprogrammed.
TheSleepmodeprogramcanbecancelled
atanytimeduringoperationbyagainpressing
theSLEEP button,orturningofftheunit,or
pressingtheMODEorFANbutton.Thisfeature
isunavailabeunderFANorDRY mode.
O O
O O
C/2 F
C/2 F1
2
NOTE:
4
44
5
3
FANbutton
SLEEP
FAN
HI
MED
LOW
TIMERON
TIMEROFF
F
C
UsedtoselecttheFanSpeedinfoursteps-
LOW,MED,HIand AUTO.
lightilluminates
underdifferentfansettingsexcept AUTO
speed.Eachtimethe buttonispressed,
thefanspeedmodeisshifted.
Thefanspeedindicator
NOTE:
4
UP()andDOWN()button
SLEEP
TIMERON
TIMEROFF
F
C
Ifyouwantthedisplaytoreadtheactual
roomtemperature,see ToOperateon
DryOnly"or
section.
"
" ToOperateonFanOnly"
Thecontroliscapableofdisplaying
temperatureindegreesFahrenheitor
degreesCelsius. Toconvertfromone
tothe other,pressandholdtheUP and
DOWNbuttonsatthesametimefor3
seconds.
NOTE:
Presstoincrease Presstodecrease
LEDDisplay
SLEEP
TIMERON
TIMEROFF
F
C
NOTE:
Showsthesettemperaturein C or
F andthe Auto-timersettings.
WhileonDRY andFANmodes,itshows
theroomtemperature.
O
O
Errorcodes:
E1-
E2-
E4-
P1-
Roomtemperaturesensorerror-
Unplugtheunitandplugitbackin.
Iferrorrepeats,callforservice.
Evaporatortemperaturesensorerror-
Unplugtheunitandplugitbackin.
Iferrorrepeats,callforservice.
Displaypanelcommunicationerror-
Unplugtheunitandplugitbackin.
Iferror repeats,callforservice.
Bottomtrayisfull-Connectthe
drainhoseanddrainthecollected
wateraway.Iferrorrepeats,call
forservice.
AIR CONDITIONER FEATURES
5
Usedtoadjust(increasing/decreasing)
temperaturesettings(1C/2Fincrements)
inarangeof17C(62F)to30C(88F)or
the TIMERsettinginarangeof0~24hrs..
6
AUTO COOL
DRY
FAN
MODE
TIMERON
TIMEROFF
F
C
SWING
SWINGbutton
AIR CONDITIONER FEATURES
UsetheSWINGbuttontoadjusttheUP/DOWN
airflowdirection(Performthisfunctionwhilethe
unitisinoperation).
1.Pressthe button,theswingfeatureis
activated.
2.Eachpresswillchangetheswinganglefor6 .
Keeppressingthebuttontomovethehorizontal
louvertothedesiredposition.
IfkeeppressingtheSWINGbuttonwithout
releasingfor2moreseconds,thehorizontal
louverwouldswingup/downautomatically.
3.PresstheSWINGbuttonagaintostopthe
movement.
SWING
o
AUTO COOL
DRY
FAN
MODE
TIMERON
TIMEROFF
F
C
SWING
MODEselectbutton
Tochooseoperatingmode,presstheMODE
button.Eachtimeyoupressthebutton,amode
isselectedinasequencethatgoesfrom AUTO,
COOL,DRY ,FAN The indicatorlightbesidewill
beilluminatedandremainedononcethemode
isselected.
NOTE:
Tooperateon Autofeature:
Inthismode,thefanspeedcannotbeadjusted,
Whenyousettheairconditionerin AUTOmode,
itwill selectcoolingorfanonly
operationtocontrolroomtemperaturesetbyyou.
automatically
TooperateonDryOnly:
Underthismode,youcannotselectafanspeedor
adjustthetemperature. Thefanmotoroperatesat
LOWspeed.
Keepwindowsanddoorsclosedforthebest
dehumidifyingeffect. Takeofftheexhausthoseand
connectcontinuousdrainagehose(locallypurchased).
Duringthisfunction,thedisplaywillshowtheactual
roomtemperature,notthesettemperatureasinthe
coolingmode.
TooperateonFanOnly:
Usethisfunctiononlywhencoolingisnot
desired,suchasforroomaircirculation.
Youcanchooseanyfanspeedyouprefer.
Duringthisfunction,the displaywillshow
theactualroomtemperature,nottheset
temperatureasinthecoolingmode.
TooperateonCoolfeature:
Pressthe ADJUST buttonsor""to
selectyourdesiredroomtemperature. The
temperaturecanbesetwithinarangeof
17 C-30 C/62 F-88 F.
Pressthe"FAN"buttontochoosethefanspeed.
O O O O
7
AIR CONDITIONER FEATURES
AUTO COOL
DRY
FAN
MODE
TIMERON
TIMEROFF
F
C
SWING
TIMERbutton
Whentheunitison,firstpressthe Timerbutton,
theindicatorlightaboveword TIMEROFFillu-
minates.Itindicatesthe AutoStopprogramis
initiated.
PressorholdtheUP arroworDOWN
arrowtochangethe Autotimeby0.5hour
increments,upto10hours,thenat1hour
incrementsupto24hours. Thecontrolwillcount
downthetimeremaininguntilstart.
Theselectedtimewillregisterin5secondsand
thesystemwillautomaticallyrevertbackto
displaytheprevioustemperaturesetting.
TurningtheunitONorOFFatanytimeor
adjustingthetimersettingto0.0willcancel
the AutoStart/Stopfunction.
WhenLEDdisplaywindowdisplayscodeofE1,
E2orE4,the AutoStart/Stopfunctionwillalso
becancelled.
Whentheunitisoff,firstpressthe Timerbutton,
theindicatorlightaboveword TIMERONillu-
minates.Itindicatesthe AutoStartprogramis
initiated.
NOTE:
8
OPERATING INSTRUCTIONS
1COOL OPERATION
-Pressthe"MODE"buttonseveraltimesuntilthe"COOL"indicatorlightcomeson.
-PresstheUP andDOWNbuttonsortoselectyourdesiredroomtemperature.
Thetemperaturecanbesetwithinarangeof17 C-30 C/62 F-88 F.
-Pressthe"FAN"buttontochoosethefanspeed.
O O O O
3FANOPERATION
-Pressthe"MODE"buttonuntilthe"FAN"indicatorlightcomeson.
-Pressthe"FAN buttontochoosethefanspeed. Thetemperaturecannotbeadjusted.
-Donotputtheducttowindow.
"
OPERATINGINSTRUCTIONS
4 AUTOOPERATION
-Pressthe"MODE"buttonuntilthe"AUTO"indicatorlightcomeson.
-Underthismode,youcannotselectafanspeed. Thefanmotoroperatesat Autofan
speed. Thetemperaturecanbesetwithinarangeof17 C-30 C/62 F-88 F.
O O O O
-Pressthe"MODE"buttonuntilthe"DRY"indicatorlightcomeson.
-Underthismode,youcannotselectafanspeedoradjustthetemperature. Thefanmotor
operatesatLOWspeed.
-Keepwindowsanddoorsclosedforthebestdehumidifyingeffect.
-Donotputtheducttowindow.
2DRY OPERATION(DEHUMIDIFY)
5TIMEROPERATION
Pressthe TIMERbuttoncansettheauto-on/offtimeoftheunit.
-Whentheunitison,firstpressthe Timerbutton,the TIMEROFFindicatorlight
illuminates.Itindicatesthe AutoStopprogramisinitiated.
-
-PressorholdtheUP orDOWNbuttontochangethe Autotimeby0.5hour
increments,upto10hours,thenat1hourincrementsupto24hours. Thecontrol
willcountdownthetimeremaininguntilstart.
- Theselectedtimewillregisterin5secondandthesystemwillautomaticallyrevert
backtodisplaytheprevioustemperaturesetting.
- TurningtheunitONorOFFatanytimeoradjustingthetimersettingto0.0willcancel
the AutoStart/Stoptimedprogram.
-Whenthemalfunction(E1,E2orE4)occurs,the AutoStart/Stoptimedprogramwill
alsobecancelled.
Whentheunitisoff,firstpressthe Timerbutton,the TIMERONindicatorlight
illuminates.Itindicatesthe AutoStartprogramisinitiated.
9
OPERATING INSTRUCTIONS
6WATERDRAINAGE:
Duringdehumidifyingmode:
-Removethedrainplugfromthebackoftheunit,
- Youcanalsoinstallthedrainconnector(5/8"(1.58cm)universalfemalemender)with3/4"(1.9cm)
hose(locallypurchasedbyconsumer)forgardenhoseuse.
attachasectionofdrainhose(includedwith
thisunit)tothehole.Placetheopenendofthehosedirectlyoverthedrainareainyour
basementfloororinawatercontainer(seeFig.4&5).
Whenthewaterlevelofthebottomtrayreachesapredeterminedlevel,
andtheunitstopsairconditioning/dehumidificationprocess.
However,thefanmotorwillcontinuetooperate(thisisnormal).Carefullymovetheunittoadrain
location,removethebottomdrainplugandletthewaterdrainaway(Fig.6).Restartthemachine
untilthe P1 symboldisappears.Iftheerrorrepeats,callforservice.
-
NOTE:
theunitbeeps8times,
thedigitaldisplayareashows P1
Removethe
drainplug
Fig.4
Continuous
drainhose
Fig.5 Fig.6
Theairconditionermustbeoperatedwithintheambienttemperaturerangeindicatedbelow:
MODE
ROOM TEMPERATURE
COOL
DRY
OPERATINGCONDITION
>13 C/54 F
O O
>17 C/62 F
O O
10
INSTALLATIONINSTRUCTIONS
Vertical
window
WindowSliderKit
Minimum:67.5cm(2.22ft).
Maximum:123cm(4.04ft).
WindowSliderKit
Minimum:67.5cm(2.22ft).
Maximum:123cm(4.04ft).
Horizontal
window
Fig.8
Fig.9
Fig.7
Location
Theairconditionershouldbeplacedonafirm
foundationtominimizenoiseandvibration.For
safeandsecurepositioning,placetheunitona
smooth,levelfloorstrongenoughtosupporttheunit.
Theunithascasterstoaidplacement,butitshould
onlyberolledonsmooth,flatsurfaces.Usecaution
whenrollingoncarpetsurfaces.Donotattemptto
rolltheunitoverobjects.
Theunitmustbeplacedwithinreachofaproperly
ratedgroundedsocket.
Neverplaceanyobstaclesaroundtheairinletor
outletoftheunit.
Allowatleast30cm(0.98ft)ofspacefromthewall
forefficientair-conditioning.
Donotuseanextensioncordoranadaptorplug.
Yourwindowkithasbeendesignedtofitmost
standard Vertical and horizontal window
applications,However,itmaybenecessaryforyouto
improvise/modifysomeaspectsoftheinstallation
proceduresforcertaintypesofwindow.Pleaserefer
toFig.8&Fig.9forminimumandmaximumwindow
openings.
WindowkitInstallation
Ifthewindowopeningislessthanthementioned
minimumlengthofthewindowsliderkit,cutthatone
withholesinitshorttofitforthewindowopening.
Nevercutouttheholeinwindowsliderkit.
Note:
30cm (0.98f t)
30cm (0. 98ft)
INSTALLATION INSTRUCTIONS
11
INSTALLATION INSTRUCTIONS
1.Cutthefoamseal(adhesivetype)totheproperlengthand
attachittothewindowstool.Fig.10
2. Attachthewindowsliderkittothewindowstool. Adjustthe
lengthofthewindowsliderkitaccordingtothewidthof
window,shortentheadjustablewindowkitifthewidthof
windowislessthan27inches.
Openthewindowsashandplacethewindowsliderkiton
thewindowstool.Fig.11
3.Cutthefoamseal(adhesivetype)totheproperlength
andattachitonthetopofthewindow.ShownasinFig.12
4.Closethewindowsashsecurelyagainstthewindow.
5.Cutthefoamsealtoanappropriatelengthandsealingthe
opengapbetweenthetopwindowsashandouterwindow
sash.ShowasinFig.13.
Foamseal A
(adhesivetype)
Foamseal
Fig.10
Fig.11
Fig.12
Fig.13
Windowkit
Windowstool
27 ~ 48
Windowkit
Windowstool
Installationindouble-hungsashwindows
12
67.5cm~123cm
INSTALLATION INSTRUCTIONS
1.Cutthefoamseal(adhesivetype)totheproperlengthand
attachittothewindowframe.SeeFig.14.
2. Attachthewindowsliderkittothewindowstool. Adjustthe
lengthofthewindowsliderkitaccordingtothewidthof
window,shortentheadjustablewindowkitifthewidthof
windowislessthan27inches.
Openthewindowsashandplacethewindowsliderkiton
thewindowstool.SeeFig.15.
3.Cutthefoamseal(adhesivetype)totheproperlength
andattachitonthetopofthewindow.ShownasinFig.16.
4.Closetheslidingsashsecurelyagainstthewindow.
5.Cutthefoamsealtoanappropriatelengthandsealingthe
opengapbetweenthetopwindowsashandouterwindow
sash.ShownasinFig.17.
Foamseal
Foamseal A
(adhesivetype)
Fig.14
Fig.15
Fig.16
Fig.17
Windowkit
27 ~ 48
Installationinaslidingsashwindows
13
INSTALLATION INSTRUCTIONS
Exhausthoseinstallation:
Theexhausthoseandadaptormustbeinstalledorremoved
inaccordancewiththeusagemode.
COOL mode
FANorDEHUMIDIFY mode
Install
Remove
The duct can be compressed or extended moderately
according to the installation requirement, but it is
desirable to keep the duct length to a minimum.
1.
Install the window Exhaust adaptor (flat mouth) onto the
exhausthoseasshowninFig.18.Refertotheprevious
pagesforwindowkitinstallation.
IMPORTANT:
DONOT OVERBEND THEDUCT (SEEFig.21)
NOTE:
Fig.18
Fig.19
Fig.20
Fig.21
Flatmouth
Pushin
Hook
2.PlacetheExhausthoseoveragainsttheairoutletopening
hook(SeeFig.19)andflattheotherend(SeeFig.20)for
quickinstallation.
14
CARE AND MAINTENANCE
CAREANDMAINTENANCE
1)Besuretounplugtheunitbeforecleaningorservicing.
2)Donotusegasoline,thinnerorotherchemicalstoclean
theunit.
3)Donotwashtheunitdirectlyunderataporusingahose.
Itmaycauseelectricaldanger.
4)Ifthepowercordisdamaged,itshouldberepairedby
manufactureroritsagent.
IMPORTANT:
1. Airfilter
-Cleantheairfilteratleastoncetwoweekstoprevent
inferiorfanoperationbecauseofdust.
-
Thisunithastwofilters.Grasptheupperfiltertab(Fig.22),
pullthefilterout.Removethelowerfilterbylooseningthe
screws,takedowntheairinletgrille,thenremovetheair
filterasshowninFig.23&24.
-
Washtheairfilterbyimmersingitgentlyinwarmwater
(about40 C/104 F)withaneutraldetergent.Rinsethefilter
anddryitinashadyplace.
-
Inserttheupperairfilterfromupwardaftercleaning,attach
thelowerairfilterontheairinletgrille,theninstallthegrille
byusingthescrew.
Removal
Cleaning
Mounting
O O
2.Unitenclosure
-Usealint-freeclothsoakedwithneutraldetergenttoclean
theunitenclosure.Finishedbyadrycleancloth.
3.Unitidleforalongtime
,,
-Removetherubberplugatthebackoftheunitandattach
ahosetodrainoutlet
(SeeFig.4&5).
-Removetheplugfromthebottomdrainoutlet,allthewater
inthebottomtraywoulddrainout(SeeFig.6).
-KeeptheappliancerunningonFANmodeforhalfadayin
awarmroomtodrytheapplianceinsideandpreventmold.
-Stoptheapplianceandunplugit,wrapthecordand
bundleitwiththetape(Fig.25).Removethebatteriesfrom
theremotecontroller.
-Cleantheairfilterandreinstallit.
-Unscrewtheexhausthosetotherightorleftandpullout
foruninstallation(Fig.26),keepitsafety.
.Placetheopenendofthehose
directlyoverthedrainareainyourbasementfloor
Fig.22
Airfilter
(slideout)
Fig.23
Fig.25
Removethe
screwand
taketheair
inletgrille
down
Removetheairfilter
outfromthegrille
Fig.24
Band
Powercord
Fig.26
15
TROUBLESHOOTING TIPS
TROUBLESHOOTING
1.Unitdoesnot
Startwhen
Pressingon/off
Button
TROUBLES
POSSIBLECAUSES
SUGGESTREMEDIES
Resetthetemperature.
Makesureallthewindowsand
doorsareclosed.
Removetheheatsourcesifpossible.
Connecttheductandmake
sureitcanfunctionproperly.
Decreasethesettemperature.
Cleantheairfilter.
-Roomtemperatureislowerthan
thesettemperature.(Coolingmode)
- Thewindowsordoorsintheroom
arenotclosed.
- Thereareheatsourcesinsidethe
room.
-Exhaustairductisnotconnectedor
blocked.
- Temperaturesettingistoohigh.
- Airfilterisblockedbydust.
2.Notcoolenough
Placetheunitonaflat,level
groundifpossible.
Itisnormal.
- Thegroundisnotlevelornotflat
enough.
- Thesoundcomesfromtheflowing
oftherefrigerantinsidethe
air-conditioner.
3.Noisyorvibration
4.Gurglingsound
-P1appearsinthedisplaywindow
Drainthewaterinthebottomtray.
16
REMOTECONTROLLERILLUSTRATION
Usetheremotecontrollerwithinadistanceof8
metersfromtheappliance,pointingittowardsthe
receiver.Receptionisconfirmedbyabeep.
Locationof theremotecontroller.
8m
CAUTIONS
Theairconditionerwillnotoperateifcurtains,doorsorothermaterialsblockthesignals
fromtheremotecontrollertotheindoorunit.
Preventanyliquidfromfallingintotheremotecontroller.Donotexposetheremote
controllertodirectsunlightorheat.
Iftheinfraredsignalreceiverontheindoorunitisexposedtodirectsunlight,theair
conditionermaynotfunctionproperly.Usecurtainstopreventthesunlightfromfalling
onthereceiver.
Ifotherelectricalappliancesreacttotheremotecontroller.eithermove
theseappliancesorconsultyourlocaldealer.
Theremotecontrollerispowedbytwodrybatteries(R03/LR03X2)
housedintherearpartandprotectedbyacover.
(1)Removethecoverbypressingandslidingoff.
(2)Removetheoldbatteriesandinsertthenewbatteries,placing
the(+)and(-)endscorrectly.
(3)Reattachthecoverbyslidingitbackintoposition.
Whenthebatteriesareremoved,theremotecontrollererases
allprogramming. Afterinsertingnewbatteries,theremote
controllermustbereprogrammed.
NOTE:
Replacingbatteries
.
Handlingtheremotecontroller
TEMP
AUTO
COOL
DRY
FAN
HIGH
MED
LOW
MODE
FANSPEED
SWING
TIMERON
ECONOMY
ON/OFF
TIMEROFF
RESETLOCK
SETTEMPERATURE(F)
LED
DISPLAY
CAUTIONS
Donotmixoldandnewbatteriesorbatteriesofadifferenttype.
Donotleavethebatteriesintheremotecontrollerifitisnotgoingtobeusedfor2or3months.
Disposeoftheoldbatteriesinthespecialcontainerstobefoundinthesalesoutlets.
17
REMOTECONTROLLERILLUSTRATION
Model
LowestVoltageof
CPUEmittingSignal
RatedVoltage
R51I13/BG(C)E
-5 C 60 C()
8m(whenusing3.0voltage,itGets11m)
3.0V(DrybatteriesR03/LR03 2)
2.0V
~
RemoteControllerSpecifications
1.OperatingMode: AUTO,COOL,DRY,andFAN.
2. TimerSettingFunctionin24hours.
3.IndoorSetting TemperatureRange:17 C~30 C(62 F~88 F).
4.FullfunctionofLCD(LiquidCrystalDisplay)
5.Backlightemitting.
O O
Environment
SignalReceiving
Range
PerformanceFeature
-41 F~140 F
O O
NOTE:
Temperaturesettingdisplay: Fahrenheitscale(F), R51I13/BG(C)E
Functionbuttons
1
TEMP UP Button
Pushthisbuttontoincreasetheindoortemperaturesettingin1 C(2F)
incrementsto30 C(88F).
o
o
2
TEMP DOWNButton
Pushthisbuttontodecreasetheindoortemperaturesettingin1 C(2F)
incrementsto17 C(62F).
o
o
Model:R51I13/BG(C)E
Eachtimethebuttonispressed,theoperationmodeisselectedinthe
sequenceofthefollowing:
3
MODEButton
TEMP
AUTO
COOL
DRY
FAN
HIGH
MED
LOW
MODE
FANSPEED
SWING
TIMERON
ECONOMY
ON/OFF
TIMEROFF
RESET LOCK
1
2
4
3
6
5
7
8
9
10
11
SET TEMPERATURE(F)
LED
DISPLAY
4
SWINGButton
Usedtostoporstartlouvermovementandsetthedesiredup/down
airflowdirection.
5
RESETButton
OncetherecessedRESET buttonispressed,allofthecurrentsettings
willbecancelledandthecontrollerwillreturntotheinitialsettings.
AUTO
COOL
DRY
FAN
12
6
7
ON/OFFButton
Operationstartswhenthisbuttonispressedandstopswhenthebutton
ispressedagain.
Usedtoselectthefanspeedinfoursteps:
AutoLowMedHigh
FANSPEEDButton
18
REMOTECONTROLLERILLUSTRATION
TIMERONButton
8
Pressthisbuttontoactivatethe Auto-ontimesetting.Eachpresswill
increasethetimesettingin30minutesincrements,upto10hours,then
at1hourincrementsupto24hours. Tocancelthe Auto-ontimesetting,
justpressthebuttonuntilthetimesettingis0.0.
9
ECONOMY(SLEEP)Button
Selectthisfunctionduringthesleepingtime.Itcanmaintainthemost
comfortabletemperatureandsaveenergy. Thisfunctionisavailableon
COOL or AUTOmodeonly.
Functionbuttonscontinued
Model:R51I13/BG(C)E
TEMP
AUTO
COOL
DRY
FAN
HIGH
MED
LOW
MODE
FANSPEED
SWING
TIMERON
ECONOMY
ON/OFF
TIMEROFF
RESET LOCK
1
2
4
3
6
5
7
8
9
10
11
SET TEMPERATURE(F)
LED
DISPLAY
12
TIMRTOFFButton
LOCKButton
NOTE: WhiletheunitisrunningunderEnergy-savingmode,itwouldbe
cancelledifanyotherbuttonsarepressed.
10
Pressthisbuttontoactivatethe Auto-offtimesetting.Eachpresswill
increasethetimesettingin30minutesincrements,upto10hours,then
at1hourincrementsupto24hours. Tocancelthe Auto-offtimesetting,
justpressthebuttonuntilthetimesettingis0.0.
11
Pressthisrecessedbuttontolockallcurrentsettings,andtheremote
controllerwillnotacceptanyoperationexceptthatoftheLOCK.Usethe
LOCKmodewhenyouwanttopreventsettingsfrombeingchanged
accidentally.PresstheLOCKbuttonagaintocanceltheLOCKfunction.
A locksymbolwillappearontheremotecontrollerdisplaywhenthelock
functionisactivated.
Pressthisbuttontoclearthedisplayontheindoorunit,pressitagainto
lightthedisplay.
LEDDisplayButton
12
TIMERONOFF
SET TEMPERATURE
TransmissionIndicator
Temp./Timerdisplay
FANSPEEDdisplay
MODEdisplay
ON/OFFdisplay
Thistransmissionindicatorwilllightwhenremotecontrollertransmitssignalstotheindoor
unit.
Displaysthecurrentselectedmode.Including AUTO,COOL,DRY,andFAN.
Thetemperaturesetting(from17 C(62 F)to30 C(88 F))ortimersetting(0~24h)willbe
displayed.IfFANmodeisselected,therewillbenodisplay.
O O O O
Thisindicatorwillbedisplayedwhentheunitisoperating.
Displaystheselectedfanspeed: AUTO,HIGH, whenthe
fanspeedisselectedin AUTOspeed.When AUTOorDRY Modeisselected,therewillbe
nosignalsdisplayed.
MEDandLOW.Nothingdisplays
Thisdisplayareashowsthesettingsofthe TIMER. Thatis,ifonlythe Auto-ontimefunction
isset,itwilldisplay TIMERON.Ifonlythe Auto-offtimefunctionisset,itwilldisplay TIMER
OFF.Ifbothfunctionsareset,itwilldisplay TIMERONOFFwhichindicatesyouhave
chosenboththe Auto-ontimeand Auto-offtime.
LOCKdisplayisdisplayedwhenpushingtheLOCKbutton.PushtheLOCKbuttontoclear
display.
MODEdisplay(FANmode)
TIMERdisplay
LOCKIndicator
IndicatorsonLCD
19
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Brada Appliances MPN1-10CR User manual

Brand
Brada Appliances
Model
MPN1-10CR
Category
Split-system air conditioners
Type
User manual
This manual is also suitable for

Brada Appliances MPN1-10CR is a portable air conditioner suitable for use in medium-sized rooms. It features an electronic control panel with an LED display that shows the set temperature and timer settings. The unit can be controlled remotely using the included remote controller.

The MPN1-10CR has four fan speeds (low, medium, high, and auto) and three operating modes: cool, dry, and fan only. The sleep mode gradually increases the temperature by 1 degree Celsius or 2 degrees Fahrenheit every 30 minutes for the first hour, then maintains the new temperature for 7 hours before returning to the original setting.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents