Frigidaire 819042236-01 User manual

Brand: Frigidaire

Model: 819042236-01

Category: Split-system air conditioners

Type: User manual

This manual is also suitable for

WALL SLEEVE INSTALLATION INSTRUCTIONS FOR

FRIGIDAIRE

THRU-THE WALL AIR CONDITIONERS

READ AND SAVE THESE INSTRUCTIONS

To avoid risk of personal injury, property damage, or

product damage duetotheweightofthisdeviceand

sharp edges that may be exposed:

• Air conditioners covered in this manual pose an

excessive weight hazard. Twoormorepeopleare

needed to moveand install theunit.

To prevent injury or strain, use proper lifting and

carrying techniques when moving unit.

• Carefully inspect location where air conditionerwill

be installed. Be sure it will support theweight of the

unit overan extended period of time.

• Handle air conditioner with care. Wearprotectivc

gloves whenever liftingor carrying theunit. AVOID

the sharp metalfins of front and rearcoils.

• Make sure air conditioner does not fall durin(

installation.

For New Construction install Frigidaire Wall Sleeve

(Part EA108T).

Remove old air conditionerand inspect sleeve forthe

following:

Installation-Make sure that sleeve is securely

installed and in sound structural condition.

Dimensions-Measure the size to make sure the air

conditioner will fit.

Slope-There should be a rearward slope for

condensate to drain from the rear of the sleeve.

Check against Fig.A.

1/4" to 5/16"

Wall Sleeve _ _E

REAR k FRONT

VEL

UNIT

Fig. A

Manufacturer-So the method of installation can be

determined.

If the installation and slope are suspect, then removal

and correct installation of a Frigidaire WallSleeve

(Part EA108T), is recommended.

Check the contents of the accessories supplied with

our air conditioner as shown below:

Number

Part name

Top/Bottom Trim Frame

Side Trim Frame

Plastic Mesh

Tapered Spacer Block Board

Tapered Spacer Block

Vertical Foam

Horizontal Foam

Vertical Trim Foam

Horizontal Trim Foam

Screw

Washer

QTY.

P/N: 819042236-01

INSTALLATION

HOW TO INSTALL

1. Identify the existing wall sleeve before installing

the unit from thelisted below.

Brand

Wall Sleeve Dimensions(inches)

Width Height Depth

White-Westinghouse 16, 17-1/:.

Frigidaire 25-1/2 15-1/4

or 22

Carrier(52F series)

General Electric

/Hotpoint 26 15-5/8 16-7/8

17-1/8

Whirlpool 25-7/8 16-1/2

or23

16-3/4

FedderstEmerson 27 16-3/4

or 19-3/4

Sears/Kenmore 25-7/8 15-17/32 16-23/32

Carrier(51S series) 25-3/4 16-7/8 18-5/8

EmersontFedders 26-3/4 15-3/4 15

Friedrich 27 16-3/4 16-3/4

NOTE: All wall sleeves used to mount the new Air

Conditioner must be in sound structural condition and

have a reargrille that securelyattaches to sleeve, or

rear flange that serves as a stop for the Air

conditioner.

2.Clean the interior of the sleeve (do not disturb

seals).

3. Repaint the sleeve if needed.

5. If thewall sleeve already has a reargrille, skip to

step 7. If the wall sleeve does not have arear grille or

Iouvered panel, install the plastic grille from the kit.

Cut the plastic mesh to match the sleeve installed.

Place the plasticgrille to theinside of thewall sleeve

at the rear flange.

Place the plastic grille

Fig. C

6.Use the 4washers and screwsto secure thegrille to

the wall sleeve.

Fasten the screws Fig. D

4.Redirect the Iouversat the backof the wallsleeve to

60 ° angle as shown in the Fig.B. The use of pliers is

recommended.

_ Rear Louvers

60 °

\\\\\\ ///////_

TopView

Fig, B

7.Remove the backing from the Vertical Foam and

attachthattotheinsiderightofthesleeve as shown

below.

Remove the backing from theHorizontalFoam and

attachthattotheinsidefront ofthe sleeve as shown

below.

Horizontal Foam Vertical Foam

Fig. E

INSTALLATION

8.If you wish to keep the unit beoperatedathigher

performance state, remove the steel rear grille and

attach the plastic rear grille. The plastic grille will

minimize the recirculation of hot discharge air.

Plastic rear grille

Steel rear grille

Fig. F

11.lnstallthe new unit intothe wall sleeve.

12.To assemble trim, snapthe tab ofeach piece into

the slot of the other piece asshown below. Remove

the backing from the trim foamand stick thattothe

inside of the trim as shown below.

Horizontal Vertical

rm oam rm oam

Assemble Trim Attach Trim Foam

Fig. 1

9.If thedepth ofyour existingwall sleeve is less than

or equal to 20", skip to step 11. Otherwise, cut the

baffles and the support blocksaccording to length"A"

in thetable below.

Depth "D"of the

existing wall Length "A"

sleeve (inches) (inches)

20<D_<20%

20%<D..<2 I_ I-_

213/4<D_<24 4

12.Slide trim over thefront ofthe airconditioner until

trim is flush with sleeve as shown below.

Fig. J

NOTE: Be sure to route the cord through the trim

frame before placing the trim frameon the unit.

10.Remove the backing from the support blocks and

attach them to the inside of the wall sleeve as shown

FIG 14.Slide the baffle intoslotsofthesupport blocks.

I /" ...................................."_ 7_"

Wall __ i_i' i BPerc_dBtPaaSer

Sleeve " _ ""'_"i" _

W__ ' ----_-Taperedspacer

.-/'/ _ Block

Fig. H

• Air conditioners covered in this manual pose an

excessive weight hazard. Two or more people arc

needed to moveand install theunit. To prevent injur_

orstrain, useproperlifting and carrying technique, _

when moving unit.

• When handling the air conditioner, be carefult(

avoid cuts from sharp metal fins onfrontand rear

coils.

• Make sure air conditioner does not fall durin(

removal.

Frigidaire 819042236-01 User manual

Brand: Frigidaire

Model: 819042236-01

Category: Split-system air conditioners

Type: User manual

This manual is also suitable for

Download PDF

report

Frigidaire 819042236-01 User manual

This manual is also suitable for

Frigidaire 819042236-01 User manual

Related papers

Other documents