Planet ICA-108 User manual

Brand: Planet

Model: ICA-108

Category: Bridge cameras

Type: User manual

This manual is also suitable for

ICA-108W

Wired / Wireless

IR IP Camera

ICA-108 / ICA-108W

User’s Manual

Version: 2.00

Date: Apr. 2008

may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any

language or computer language, in any form or by any means, electronic, mechanical, magnetic,

optical, chemical, manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with respect to

the contents hereof and specifically disclaims any warranties, merchantability or fitness for any

particular purpose. Any software described in this manual is sold or licensed "as is". Should the

programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or

its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or

consequential damages resulting from any defect in the software. Further, PLANET reserves the

right to revise this publication and to make changes from time to time in the contents hereof

without obligation to notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or

registered trademarks of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

1. Reorient or relocate the receiving antenna.

2 Increase the separation between the equipment and receiver.

3 Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

To assure continued compliance. (example-use only shielded interface cables when connecting

to computer or peripheral devices). Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two

conditions: ( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must

accept any interference received, including interference that may cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled

environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure

limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal

operation.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it.

However, special attention must be paid to the dangers of electric shock and static electricity

when working with electrical equipment. All guidelines of this and of the computer

manufacture must therefore be allowed at all times to ensure the safe use of the equipment

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

WEEE Regulation

To avoid the potential effects on the environment and human health as a result of the

presence of hazardous substances in electrical and electronic equipment, end users

of electrical and electronic equipment should understand the meaning of the

crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal

waste and have to collect such WEEE separately.

Revision

User’s Manual for PLANET Wired / Wireless IR IP Camera

Model: ICA-108 / 108W (for F/W v 3.0 or above)

Rev: 2.0 (Apr. 2008)

Part No. EM-ICA108_W_v2

Table of Content

1. Introduction................................................................................................................ 5

1.1 Overview............................................................................................................. 5

1.2 Features.............................................................................................................. 5

1.3 Package Contents............................................................................................. 6

2. Basic Setup............................................................................................................... 7

2.1 System Requirements....................................................................................... 7

2.2 Physical Description.......................................................................................... 8

2.3 Hardware Installation........................................................................................ 8

2.4 Initial Utility Installation ..................................................................................... 9

2.5 IP Wizard........................................................................................................... 12

2.6 Configure With IP Wizard............................................................................... 14

2.7 UPnP Function................................................................................................. 17

2.7.1 Windows XP.......................................................................................... 17

2.7.2 Windows Vista ...................................................................................... 21

2.8 Setup ActiveX to use the IR IP Camera....................................................... 23

2.8.1 Internet Explorer 6 for Windows XP.................................................. 23

2.8.2 Internet Explorer 7 for Windows XP.................................................. 24

2.8.3 Internet Explorer 7 for Windows Vista............................................... 25

3. Web-based Management...................................................................................... 26

3.1 Introduction....................................................................................................... 26

3.2 Connecting to IR IP Camera.......................................................................... 26

3.3 Live View........................................................................................................... 28

3.4 ActiveX Control ................................................................................................ 30

3.4.1 Digital Zoom.......................................................................................... 31

3.4.2 Record.................................................................................................... 31

3.4.3 Snapshot................................................................................................ 32

3.4.4 Voice....................................................................................................... 32

3.4.5 Statistics................................................................................................. 33

3.4.6 About...................................................................................................... 33

3.5 Network............................................................................................................. 34

3.5.1 Network.................................................................................................. 34

3.5.2 Wireless (ICA-108W only) .................................................................. 35

3.5.3 DDNS server......................................................................................... 38

3.5.4 PPPoE.................................................................................................... 39

3.5.5 Streaming .............................................................................................. 40

3.5.6 UPnP...................................................................................................... 41

3.5.7 IP Filter................................................................................................... 42

3.5.8 IP Notification........................................................................................ 43

3.6 Camera.............................................................................................................. 46

3.6.1 Picture.................................................................................................... 46

3.7 System............................................................................................................... 48

3.7.1 System................................................................................................... 48

3.7.2 Date & Time........................................................................................... 49

3.7.3 Maintenance.......................................................................................... 50

3.8 Video.................................................................................................................. 52

3.8.1 Common................................................................................................ 52

3.8.2 MPEG4/VGA......................................................................................... 53

3.8.3 MPEG4/QVGA...................................................................................... 54

3.8.4 MPEG4/QQVGA................................................................................... 55

3.8.5 VIDEO/JPEG......................................................................................... 56

3.9 Audio.................................................................................................................. 57

3.10 User................................................................................................................. 58

3.11 E-Mail............................................................................................................... 59

3.12 Object Detection............................................................................................ 60

3.13 Event Server .................................................................................................. 61

3.13.1 FTP Server.......................................................................................... 61

3.13.2 TCP Server.......................................................................................... 62

3.13.3 HTTP Server....................................................................................... 63

3.14 Event Schedule.............................................................................................. 64

Appendix A: Reset Factory Default Settings.............................................................. 66

Appendix B: PING IP Address...................................................................................... 67

Appendix C: Bandwidth and Video Size Estimation................................................. 68

Appendix D: DDNS Application.................................................................................... 70



1. Introduction

The ICA-108/108W is a wired/wireless IR IP Camera. The ICA-108/108W can send live video and

audio via the internet to a web browser anywhere in the world.

The ICA-108/108W features zero-lux illumination. The 6 IR illuminators built around the lens bring

the clearest vision at night. The ICA-108/108W offers color picture in day time and monochrome at

complete darkness with built in CMOS sensor up to 10 meters. Use new High-Light LED to provide

greater performance in the dark and longer life of LED.

Multi-profile stands for video stream simultaneously. The ICA-108/108W can generate MPEG-4

and M-JPEG streaming to different users in the meantime. Moreover, the resolution can differ from

one user to another. This state-of-art design is considerable to fit in various network environments.

Up to 10 users can access to the ICA-108/108W at any time simultaneously.

The ICA-108/108W takes surveillance to use 2-way audio. It can remotely talk to anyone at

ICA-108/108W site when adding a speaker on ICA-108/108W. The ICA-108W uses IEEE

802.11b/g wireless technology that communicates at a maximum wireless signal rate of up to

54Mbps and security features include WEP and WPA encryption.

1.1 Overview

This user’s manual explains how to operate the wired/wireless IR IP Camera from a computer.

Basically, the user’s manual is written to be read on the computer display. However, users might

consider printing it out to access easily and read it before you operate the Network Camera. This

manual shows how to set up the two cameras, unless model name specified terms “IR IP Camera”

will be used for these two models.

1.2 Features

• AXIS compatible SDK

• High quality of CMOS image sensor

• Clear and high resolution quality pictures for day and night

• 3GPP for 3G mobile remote applications

• Multi-profile encoder supports MPEG-4 and M-JPEG video compression simultaneously and

30fps for all resolution

• 2-way audio with built-in microphone

• LED used on IR IP Camera are 4 times brighter than ordinary IR LED and visible distance up

to 10 meter

• The ICA-108W supports IEEE 802.11b/g wireless LAN with WEP and WPA encryption

• Plug-N-Watch is able to simplify the system integration in existing network environment

• Because of supporting TCP / IP networking, SMTP e-mail and HTTP public network

standards, IR IP Camera can be applied and utilized to a mixed IP network environment

• Easy configuration: Network administrators can configure and manage IR IP Camera via

Windows-based utility or web interface

• DDNS, PPPoE and FTP uploading support provide more alternatives in surveillance network

• Motion Detection: the motion detection feature can monitor any suspicious movement in

specific area

1.3 Package Contents

User can find the following items in the package:

1. IR IP Camera x 1

2. Power adapter x 1

3. Wall mount accessories x 1

4. Utility and manual CD x 1

5. Quick Start Guide x 1

6. External Antenna (ICA-108W only)

NOTE: 1. If any of the above items are missing, please contact your dealer immediately.

2. Using the power supply that is not the one included in IR IP Camera packet will

cause damage and void the warranty for this product.

2. Basic Setup

This chapter provides details of installing and configuring the wired/wireless IR IP Camera.

2.1 System Requirements

Network Interface 10/100MBase-TX Ethernet

Monitoring System Recommended for Internet Explorer 6.0 or later

System Hardware · CPU: Pentium 4, 1.5GHz or above

· Memory Size : 512 MB (512 MB or above Recommended )

· VGA card resolution : 1024 x 768 or above

· Network bandwidth: In VGA resolution mode, minimum

upload bandwidth is 1Mbps.

NOTE: The listed information is minimum system requirements only. Actual requirement will

vary depending on the nature of your environment.

2.2 Physical Description

LAN Socket DC 5V Power Jack

Audio Output Reset to Default Button

1. LAN Socket

The LAN port is a RJ-45 connector for connections to 10Base-T Ethernet or 100Base-TX

Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the

transmission speed of the network automatically. Please use Category 5 “straight” cable to

connect the IR IP Camera to a 100Mbps Fast Ethernet network switch or hub.

Note: In case you need to connect the device to PC or notebook directly, you should use

a cross-over cable instead.

2. Audio Output

Audio output jack allows this device to output audio or alerting sound.

3. DC Power Jack

The DC power input jack is located on the IR IP Camera. The input power is 5V DC.

Note: Using the power supply that is not the one included in IR IP Camera packet will

cause damage and void the warranty for this product.

4. Reset to Default Button

This button is hidden in the pinhole beside the DC Power Jack. Please refer to the Appendix

A in this manual for more information.

2.3 Hardware Installation

1. Attach the IR IP Camera with the included stand.

2. Locate the IR IP Camera on the table or fix it onto ceiling or wall.

3. Plug an Ethernet cable into the IR IP Camera.

4. Assemble the antenna to ICA-108W.

5. Connect the external power supply to IR IP Camera.

6. Done.

2.4 Initial Utility Installation

This chapter shows how to quick set up your IR IP Camera. The IR IP Camera is with the default

settings. However to help you find the IR IP Camera quickly the windows utility-IP Wizard can

search the IR IP Cameras in the network that shall help you to configure some basic setting before

you started advanced management and monitoring.

1. Insert the bundled CD into the CD-ROM drive to launch the autorun program. Once completed,

a welcome menu screen will appear.

2. Click the “IP Wizard” hyperlink; you will see the InstallShield Wizard dialog box as below.

NOTE: If the welcome screen does not appear, click “Start” at the taskbar. Then, select

“Run” and type “D:\Utility\setup.exe”, assume D is your CD-ROM drive.

3. The “Welcome to the InstallShield Wizard for IP Wizard” will display on the screen and click

“Next” to continue.

4. Please click “Next” to install with original settings, or you may click “Change…” button to

modify the install folder then press “Next” to continue.

5. Please click “Install” to start the installation.

6. Please click “Finish” to complete the installation

7. Please double-click the utility icon

on the desktop then you will see the IR IP

Camera utility.

2.5 IP Wizard

When you installed the IR IP Camera on a LAN environment, you may execute IP Wizard to

discover IR IP Camera’s IP address and set up related parameters in the IR IP Camera.

NOTE:

The ICA-108 installation steps are similar. Below is the installation of ICA-108W.

Search Button:

When click Search button, a searching window will pop up. IP Wizard is starting to search Internet

Camera on the LAN. The message “No Network Devices Is Found” will appear on this window if IP

Wizard cannot find any IR IP Camera on the LAN. Otherwise, existed IR IP Cameras will be listed.

If total quantity is over, please move the cursor to Information Box. Click on the left button of the

mouse and the Information Box of the Listing Window will roll upward automatically; on the

contrary, move the cursor to the Information Box on the top of Listing Window and click on the left

button of the mouse and Listing Window will roll downward.

Wizard Button:

When IP Wizard finds your IR IP Camera, Wizard button will become available. Please select the

device you would like to configure in the Information Box. The device will turn into yellow which

means this device is selected; please press “Wizard” button. Or you could double click the mouse

left key on the selected IR IP Camera. Relative settings will be carried out. Details of Install Wizard

will be specified as Section 2.6.

About Button:

When click “About” button, you will see the version information of IP Wizard shown in the pop-up

dialog box.

Exit Button:

Click “Exit” button will close the IP Wizard Program.

2.6 Configure With IP Wizard

After pressing Installation Wizard, please key in Username and Password of the device when login

dialog box appears on the screen. You can login the setup page if authorized name and password

is correct. Default username/password for machine login: admin/<no password>

Wizard Page 1: Username and Password

This page is about the change of the authorized user name and password of the selected device. If

you don’t want to change them, please click “Next” to move to the next page. Press “Exit” button if

you don’t want to set up right now. If you want to change authorized name or password, you have

to check the box in front of ID or New Password. Authorized Username should contain at least 5~

20 characters and New Password should contain at least 4~8 characters.

Wizard Page 2: LAN Setting

This page is about the select of Static IP or DHCP ON.

LAN: You can configure this IR IP Camera to obtain its address automatically or

manually assign. If there is a DHCP server in your network environment and

you select “DHCP ON”, IR IP Camera can automatically obtain an IP address.

If you don’t have DHCP server or you want to use fixed IP address, please

select “Static IP” and fill in the following fields with proper parameters.

IP Address: IP address is a unique number for identifies this device on the WAN or LAN.

These numbers are usually shown in groups separated by periods, for

example: 192.168.0.200

Subnet Mask: Subnets allow network traffic between hosts to be separated based on the

network's configuration. In IP networking, traffic takes the form of packets. IP

subnets advance network security and performance to some level by

organizing hosts into logical groups. Subnet masks contain four bytes and

usually appear in the same "dotted decimal" data. For example, a very

common subnet mask in its binary demonstration 11111111 11111111

11111111 00000000 will usually be shown in the corresponding, more

readable form as 255.255.255.0.

Def. Gateway: A gateway is a piece of software or hardware that passes information

between networks. You'll see this term most often when you either log in to

an Internet site or when you're transient email between different servers.

DNS1: When you send email or position a browser to an Internet domain such as

xxxxx.com, the domain name system translates the names into IP addresses.

The term refers to two things: the conventions for naming hosts and the way

the names are control across the Internet.

DNS2: The same function as DNS1. It is optional, not necessary

Note: If no IP address is assigned after 30 seconds, the IR IP Camera will work with its default IP

address 192.168.0.20. User may now open your web browser, and key in http://192.168.0.20 in

the address bar of your web browser to logon IR IP Camera’s web configuration page.

Wizard Page 3: Confirmation

This page shows the new configurations. If it is correct, please press “Submit” icon and the setting

information will be save to your IR IP Camera. Click on “Exit” to close this window.

2.7 UPnP Function

NOTE: Windows 2000 does not support UPnP feature.

2.7.1 Windows XP

UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides

compatibility among networking equipment, software, and peripherals. This device is an UPnP

enabled device. If the operating system, Windows XP, of your PC is UPnP enabled, the device will

be very easy to configure. Use the following steps to enable UPnP settings only if your operating

system of PC is running Windows XP.

Go to Start > Settings, and Click Control Panel

The “Control Panel” will display on the screen and double click Add or Remove Programs to

continue

The “Add or Remove Programs” will display on the screen and click Add/Remove Widows

Components to continue.

The following screen will appear, select Networking Services and click Details to continue

The “Networking Services” will display on the screen, select Universal Plug and Play and click

OK to continue.

Please click Next to continue

Page is loading ...

Planet ICA-108 User manual

Brand: Planet

Model: ICA-108

Category: Bridge cameras

Type: User manual

This manual is also suitable for

ICA-108W

Download PDF

report

Planet ICA-108 User manual

This manual is also suitable for

Planet ICA-108 User manual

Related papers

Other documents