3com 45-338 User manual

3com
Brand
3com
Model
45-338
Category
Cable network testers
Type
User manual

This manual is also suitable for

DataComm
G
Section G - DataComm 10/22/08 8:18 AM Page 1
Testers
www.idealindustries.com 1-800-435-0705 for Customer Service
G-2
LANTEK
®
6/6A/7G LAN Cable Certification Testers
L
ANTEK offers a family of high performance cable certification testers to support a full range of LAN cable testing. The LANTEK family
of certification testers uses the I
DEAL patented measurement system that removes the effects of ordinary patchcords, thus making
channel and permanent link certification of a cable standard such as CAT6A or ISO-F possible without changing adapters. The same
patented technology also makes DUALmode Testing possible so the users can get any two test results simultaneously. As a result, the
LANTEK Cable Certification Testers save you money and time on the job.
n LANTEK 7G 1GHz is the world’s first independently verified Level IV accurate LAN cable certification tester capable of testing installations
up to 1 G
Hz, exceeding the requirements for CAT6A/7/ISO-F.
n LANTEK 6A 500MHz is a Level IIIe verified certification tester designed to support the NEW CAT6A Standard to certify LAN cabling to
support applications up to 1
0G Ethernet.
n L
ANTEK 6 350MHz
is a L
evel III verified LAN certification tester designed to support up to CAT6/ISO-E cabling.
Features of LANTEK
®
Products
n
High-Performance LANTEK 7G/6A/6 – sweeps
to 1 GHz and supports testing requirements up to
CAT 6/6A/7/ISO-F and beyond
n
Level IV/IIIe/III Accuracy – independently verified
by ETL for baseline, channel and permanent link
n
DUALmode Testing to Save Time – reports
channel and permanent link test results simultaneously
n
Test with Patchcords to Save Money – performs
CAT6A/6/5e/ISO-Ea/E/D testing with standard
patchcords to achieve the lowest cost of ownership
n
Largest Internal/External Memory Capacity –
makes r
ecor
d management easy
n
Convenient FIBERTEK™ Accessory –
simultaneously tests two fibers f
or attenuation and
length
n
Innovative TRACETEK™ Accessory – performs
advanced fiber f
ault location and tr
oubleshooting
functions
The only
certifier
to sweep
to 1GHz
Section G - DataComm 10/22/08 8:18 AM Page 2
DataComm Equipment
1-800-435-0705 for Customer Service www.idealindustries.com
G-
3
FEATURES
LANTEK7G
Premium
LANTEK6A
Premium
LANTEK6
Basic
Frequency Range 350 MHz 500 MHz 1 GHz
Supports CAT7 & ISO-F Upgradeable Upgradeable 4
Supports CAT6A Upgradeable 44
Support CAT6/5e/3 and ISO-E/D/C 4 4 4
Accuracy Level III/IIIe (Draft)/IV
(LANTEK6/6A/7G) verified by
ETL ETL ETL
Support DUALmode Testing to
Save Time
444
Test with Patchcords to Save Money 4 4 4
Screen Display Area Best Best Best
CAT6 Test Storage with Graphs 500 500 500
Standard External Compact Flash
Memory
Option
64MB
64MB
USB/Serial Port 4
44
Copper TDR T
race
4
4
4
Fiber Loss Measurement (FIBERTEK) Option Option Option
Fiber Distance to Break (TRACETEK)
Option
Option Option
Talk over Fiber & Copper
(Full Duplex)
444
Display Screen on Remote 4
4
4
Troubleshooting Tone Generator
on Remote
4
4
4
External Rapid Battery Charger &
Extra Batteries
Option 44
Kits Include:
Soft Carrying Case 44 ––4 ––
Deluxe Hard Shell Case –– 4 ––4 –
Airline Grade Travel Case with Wheels –– – 4 ––4
64MB Compact-Flash Memor
y Card
–
–
44– 44
Category 6 Universal Adapters & Reference Cables
4 –– –– – –
Category 6A Universal Adapters & Reference Cables
– 44 44 4 4
Batteries 22 4 4 2 4 4
DUAL Bay Rapid Batter
y Charger
–
–
4
4
– 4
4
Headsets (2), AC Adapters (2),
Hanging Straps (2), Serial Cable (1),
44 4 4 4 4 4
USB Cable (1), LANTEK Reporter Software (1)
PACKAGE AND ACCESSORIES
LANTEK7GPREM
Premium
LANTEK6B
Basic
LANTEK6ABAS
Basic
LANTEK6APREM
Premium
LANTEK6ATRV
Travel
LANTEK7GBAS
Basic
LANTEK7GTRV
Travel
Note:
Delivery content may vary outside of US. Please contact your local IDEAL sales office for details.
The airline grade Travel Case fits in most airline overhead storage compartments.
Other Accessories LANTEK6/6A/7G
Soft Carry Case 3010-12-0096
Deluxe Hard Carry Case 3010-12-0092
Batteries 1219-00-1604
Serial Cable 6011-50-0031
64 MB CompactFlash Card 2112-27-0605
CompactFlash Card Reader for PC 2112-27-0604
LANTEK CAT 6/5e Channel Adapters (ea.) 0012-00-0629
LANTEK CAT 6A/6/5e Channel Adapters (ea.) 0012-00-0656
LANTEK CAT 6A/6/5e Reference Patchcords (ea.) 6011-50-0029
Talkset (2) 3010-70-0015
Dual Bay Batter
y Charger 0012-00-0642
LANTEK CA
T 7 TERA Testing Kit 1019-00-1105
LANTEK CAT 7 NEXANS Testing Kit 1019-00-1110
Coax Testing Adapter Kit 1019-00-0343
110 Block Testing Adapter Kit 1019-00-1112
BIX Block Testing Adapter Kit 1019-00-1114
66 Block Testing Adapter Kit 1019-00-1115
Testers
Section G - DataComm 10/22/08 8:18 AM Page 3
Testers
www.idealindustries.com 1-800-435-0705 for Customer Service
G-4
FIBERTEK™ and TRACETEK™ Advanced Fiber Test Options
FIBERTEK/TRACETEK PACKAGES
FIBERTEK – 850nm MM Adapter 44 44
FIBERTEK – 1300nm MM Adapter 44 44
FIBERTEK – 1310nm SM Adapter 4444
FIBERTEK – 1550nm SM Adapter 4444
TRACETKEK – 1300nm MM Adapter 444
TRACETKEK – 1310NM SM Adapter 444
Fiber Cleaning Starter Kit 44444444
62.5/50µm, MM, ST-ST Cable Kit 44 44
62.5/50µm, MM, FC-ST/FC-SC Cable Kit 444
9µm, SM, FC-ST Cable Kit 4444
9µm, SM, FC-ST/FC-SC Cable Kit 444
See your IDEAL representative for additional
specifications on all certification products.
TRACETEKSM
FIBERTEKMMB
FIBERTEKMMP
FIBERTEKSMB
FIBERTEKSMP
FIBERTEKALLB
FIBERTEKALLP
TRACETEKMM
F
eatures of FIBERTEK™ Products
n
Measur
es signal loss and length
n
850nm VCSEL light source enables Gigabit
Ethernet certification on Multimode fiber
n
Enables bi-directional, dual
wav
elength measurements
n
Full duplex talkset capability
n
Provides easy switching of LANTEK
®
Cable T
ester between Copper and Fiber
L
AN testing
n Separate loopback testing method for high precision length
n Outstanding T
emperature Compensation provides highly accurate
test results in a wide variety of environments
FIBERTEKMMP Multimode Fiber Testing Premium Kit
n All of the f
eatures of the FIBERTEKMMB plus TRACETEKMM
(below):
F
IBERTEKSMP Singlemode Fiber Testing Premium Kit
n All of the features of the FIBERTEFKSMB Plus TRACETEKSM
(below):
Features of TRACETEK™ Products
n
Enables LANTEK
®
certification testers to provide an event trace
at a fraction of the price of an OTDR
n
Provides easy switching of LANTEK
®
certification tester between
FIBERTEK™ loss and length measurement and TRACETEK™
n
Includes event plots that pinpoint significant losses along the fiber
n
Provided with launch cable and appropriate connectors
Section G - DataComm 10/22/08 8:18 AM Page 4
Testers
DataComm Equipment
1-800-435-0705 for Customer Service www.idealindustries.com
G-
5
SIGNALTEK™ Gigabit Ethernet Certifier
SIGNALTEK™ provides a technically innovative method to test and document performance of voice,
data, video and VoIP applications for cabling installers and network technicians. It tests the link's
ability to support applications by tr
ansmitting Ethernet packets on the wire and measuring the link
performance according to IEEE 802.3ab Gigabit Ethernet standard. By monitoring transmitted and
received data packets, it can report the BERT (Bit Error Rate Test) for the link. It uses the latest
generation of Gigabit Ethernet technology to provide the best performance to this new class of testers.
Features of SIGNALTEK™
n
Unique - Simulate real world network traffic with full-duplex
gigabit performance testing
n
Unique - User selectable 10/100/1000 Bit Error Rate Testing
(BERT) to ensure performance for all Ethernet devices
n
Unique - Smart autotest function detects line condition and
automatically chooses appropriate test to run to allow testing
cable that is terminated with a SIGNALTEK remote, a
network device or unterminated
n
Unique - Save time using the remote to perform 10/100 or
gigabit service detection AND initiate an Autotest when main
unit is connected
n
Unique - Maximum flexibility with two USB ports. Connect
to a computer to upload test results, connect directly to a
printer, or connect a USB memory drive for unlimited storage
n
Unique - Get maximum coverage with a full two-year warranty
n
Unique - Configure multiple target IP addresses for pinging
several network devices to ensure communications with
servers, printers, IP cameras, home automation controls, etc.
n
Offers network interrogation tools such as link establishment,
port LED blink and ping
n
TDR to accurately measure length and locate shorts and opens
n
ARP test discovers active network devices
n
Exceeds 100m measurement dist
ance required by I
E
E
802.3ab gigabit Ethernet standard
n
Easy-to-read Pass/Fail performance reports that can be
stored and printed for customer documentation
n
Multiple BERT configurations for VoIP, data, and video-over-
IP specific testing
n
Brilliant high-resolution color display visible in any lighting
condition
n
Uses readily available AA batteries
n
W
iremap faults easily with selectable 568 A/B color coding
Description Cat. No.
SIGNALTEK™ Kit 33-974
Universal 120-240V Power Adapter 4010-00-0136
RJ-45 to 8 Head Alligator Clip K-7920
Replacement Cable Accessory Kit - contains all original
cables in SIGNALTEK™ Kit
1219-91-0003
#33-974
SIGNALTEK™ Specifications
Cable T
ypes
n Voice/phone cable - USOC/RJ-11/RJ-12 interface
n Data Cable - STP/UTP (RJ-45) for CAT 3/5e/6/6a/7 cabling
n Coax c
able - via RJ-45 to F P
atchcord, serie
s 6, 5
9, 5
8 c
abling
(50/75 Ohm)
Physical Dimensions
n Display handset: 7
.9” L x 3.6” W x 1.5” D
n Remote handset: 6.8” L x 3.5” W x 1.5” D
n Near-end Weight: 12.5 oz.
Ports/Connections
n RJ-45 te
st inter
face por
t
n Mini U
S
B “
A” port
n St
andard U
SB “B” port
n D
C power input for long-term network monitoring
Section G - DataComm 10/22/08 8:19 AM Page 5
Testers
www.idealindustries.com 1-800-435-0705 for Customer Service
G-6
SIGNALTEK™-FO Multimedia Ethernet Certifier
Description Cat. No.
SIGNALTEK™-FO w/850 Modules 33-981
SINGALTEK™-FO w/13X0 Modules 33-982
SIGNALTEK™-FO w/850 & 13X0 Modules 33-983
SIGNALTEK™-FO w/o Modules (Fiber-Ready) 33-987
SIGNALTEK-FO is the first active ethernet certifier that offers both copper and fiber optic testing; and SIGNALTEK-FO does
it f
or less than the price of an Optical Test Set alone.
n Fiber Optic and Copper Gigabit Certification – Qualify copper and fiber-optic cabling to IEEE 802.3 standards
n Multimedia Gigabit Certification (Multimode and Single Mode capability) – Qualify short and long r
ange cabling
to a distance of up to 1
0km
n BERT and Optical Attenuation Measurements – Perform Bit Error Rate Testing and decibel (dB) loss measurements
of optical links.
n Dual W
avelength Capability – available in both 850nm and 1300mn wavelengths to support virtually all LAN and
campus fiber applications.
n Small Form factor Pluggable (SFP) modules are compact, light-weight and field changeable.
n Storage and Reporting for Thousands of Reports – Store and print Qualification reports for copper and fiber jobs
using internal memory or USB “thumb-drives”.
10 Gigabit Alien Crosstalk Testing Kit
Description
Cat. No.
Alien Crosstalk T
esting Kit for LANTEK
LANTEK10GBKIT
P
erform a standard 6-around-1 cable test with PS ANEXT and PS AACR-F results
for both ends of the cable in as little as 5 1/2 minutes compared to over 20 minutes for
some competitive models.
n Add Alien Crosstalk testing capability to any LANTEK
®
6A or 7G
n P
erf
orm P
S Alien NEXT and Attenuation to Alien Crosstalk Ratio measurements
n Unique Dual-port AXT adapter allows PSANEXT testing with just one handset
f
or quick initial site testing
n Dual-handset mode allows complete AXT certification 4 times faster
than other A
X
T test systems
n No PC required in the field - all test results calculated on-the-fly for
instant pass/fail indication
n Kit includes 2 Dual-port AXT adapters, 12 AXT terminators, shielded
patch cords, manual, firmware update and PC reporting software
#33-983
Section G - DataComm 10/22/08 8:19 AM Page 6
Testers
DataComm Equipment
1-800-435-0705 for Customer Service www.idealindustries.com
G-
7
SecuriTEST™ CCTV/Security Tester
SecuriTEST™ PRO CCTV/Security Tester
CCTV installers often need to carry a variety of testing tools to complete their work.
SecuriTEST combines the most-needed tools in one easy-to-carry package. Since all
connections (video/communications/DMM) attach to a single unit, SecuriTEST
eliminates the need to juggle sev
er
al devices while on a ladder or lift, making working
conditions safer and increasing productivity.
n Seven Essential CCTV Tools – Combines a CCTV video tester, PTZ camera
controller, Digital Multi-Meter, UTP cable tester, video test pattern generator,
PTZ protocol analyzer and camera programmer in a single compact package.
n Save Time & Money – Test, aim, focus and program cameras when working
alone. Sav
e time by not having to walk back to the contr
ol center to v
erify
functionality of each camer
a.
n Compact Design – Combines all the most needed—security tools in a
lightweight, easy-to-carry unit. Sharp, bright 2.5in (6.3cm) color L
CD screen
with on-screen displays for PTZ
control/diagnostics and DMM
r
eadouts.
n PTZ Protocol Analyzer –
Compatible with 20+ PTZ
protocols to test and program
cameras in the field. Decodes
and identifies output from
PTZ console to aid in
troubleshooting.
SecuriTEST™ PRO adds to the already impressive capabilities of the SecuriTEST™
by including all the features of the original, plus IRE testing (video and sync levels),
audio lev
el testing, a high-capacity lithium ion battery in a package that’s smaller
and lighter than before. The SecuriTEST™ PRO has all the features and
functionality that CCTV technicians need to install, test and maintain analog
security camer
a systems. SecuriTEST™ PRO also includes a custom carrying
case (optional with the standard SecuriTEST™).
Features of SecuriTEST™ PRO
n
All the same features of the
SecuriTEST™ plus:
n
NEW - IRE video level and sync tests
n
NEW - Sound level test through integrated
speaker and on screen level indicator
n
NEW - High capacity lithium ion battery
n
NEW - Support for additional PTZ protocols
n
NEW - Carrying case included
LED Indicators
T
est Lead Ports
Carrying Case (62-891)
Includes: Rechargeable batteries,
AC
charger
, car charger
, test leads,
wiremap terminator
, neck strap and
manual.
PTZ Control Pad
Main Power Switch
Description
Cat. No.
SecuriTEST™ CCTV/Security T
ester only
33-891
SecuriTEST™ T
ester Pouch only
62-891
Description Cat. No.
SecuriTEST™ PRO CCTV/Security Tester only 33-892
SecuriTEST™ Tester Pouch only 62-891
NEW
Audio Input
LED Indicators
PTZ Control Pad
IRE On/Off
Test Lead Ports
UTP Test Port
Section G - DataComm 10/22/08 8:19 AM Page 7
LAN Cable Testers
www.idealindustries.com 1-800-435-0705 for Customer Service
G-8
LinkMaster™ PRO and LinkMaster™ PRO XL Testers
Six Modes of Operation
• Cable Test
• Hub Blink
• Tone
• Length
• Coax
• Setup Mode
Main Jack for all Testing
Remote Jack for Patch Cords
Larger Backlit LCD
Screen
Press SEL to:
• Turn on back-light (Hold 2 sec)
• Execute current displayed mode
• Start new test cycle
• Select one of four tones
•
Change pair being measured
for length
• Change user selectable options
– Beep On/Off
– Unshielded or Shielded Cable
– Units—Feet or Meters
Arrow Keys
• To change length constant
• To change pair or pin selection for tone
• To scroll through setup selectable options
Features
T
he LinkMaster™ PRO & LinkMaster™ PRO XL Testers enable
installers, contractors and maintenance technicians to map, test
and troubleshoot data and voice communication cable and coax
runs. Rugged, versatile, and easy-to-use, they have mastered the
link between perf
ormance, simplicity and value for both commercial
and residential applications.
RJ-45 to RJ-11Jack Adapter (2/card),
POP Packaging
RJ-45 to F-Connector Adapter (2/card),
POP Packaging
LinkMaster™ Pro XL
Remotes UTP/STP
,
2-8 only (white carton)
LinkMaster™ Pro XL Large Replacement Case
BNC Accessory Kit
Set of Eight Color
-Coded F-T
erminators for
LinkMaster™ Pro or Pro XL
LinkMaster™ Pro Large Replacement Case
Replacement Economy Kit Case
LA-4233
LA-4234
LA-4235
H-3412
LA-4157
LA-4173
LA-4159
H-3324
H-4868
Accessories
Description Cat. No.
Kits
Description
Cat. No.
LinkMaster™ PRO XL
Kit w/eight
remotes 33-880
LinkMaster™ PRO XL
Kit w/eight
remotes and T
one &
Probe
33-881
LinkMaster™ PRO XL
Kit w/eight
remotes – International Packaging 33-886
LinkMaster™ PRO XL
Economy Kit
33-887
w/one remote
LinkMaster™ PRO Kit w/eight
remotes – Unshielded Jumper Cables 33-825
LinkMaster™ PRO Kit w/eight
remotes – Shielded Jumper Cables 33-826
LinkMaster™ PRO Economy Kit w/one
remote – Unshielded Jumper Cables 33-835
LinkMaster™ PRO Economy
Kit w/one
remote – Shielded Jumper Cables 33-836
Description
LinkMaster™ LinkMaster™
PRO PRO XL
Blinks the hub n
Displays length measurement with test results n
Remotes have both RJ-11 and RJ-45 jacks n
Backlight LCD screen n
Measures length on UTP, STP and coax nn
Tests UTP for shorts, opens, miswires, reversals,
nn
split pairs and shield continuity
Test coax for opens, shorts and continuity nn
Shows wiring errors nn
Tests and identifies with all eight twisted pair
and coax remotes
n n
Sends tone with four different signals n n
Displays test results in wire map format n n
Snap-off battery cap n n
9 volt battery included n n
Security/Speaker Kit – 8-Position Modular
Adapter and eight RJ-45 to Alligator Clip
Lead Sets
Section G - DataComm 10/22/08 8:19 AM Page 8
Testers
DataComm Equipment
1-800-435-0705 for Customer Service www.idealindustries.com
G-
9
Amplifier Probe and Tone Generator
Amplifier P
robe
n Identifies and traces wire or cables within a group
n Battery low indicator
Tone Generator
n Emits three different types of tones
n Auto-off after thr
ee hours of non-use
n F-Connector port for toning & tracing coaxial CATV cabling
systems
n Tone can be added in any status
Description Cat. No.
Amplifier Probe 62-164
Tone Generator 62-160
Amplifier Probe & Tone Generator Kit - includes 62-164, 62-160,
Lead Set, Cable Assembly & Standard Replacement Tip
33-864
TRACETone™ Tone Generator &
Amplifier Probe
n Test continuity and locate signal
of installed wire and cable
n Two selectable tone styles
n Tone Generator & Amplifier
Probe fit together for easy storage
n Extr
a-deep serr
ations grip wir
e better
n RJ-11 Alligator Clip, RJ-11 Cable Assembly included
Description Cat. No.
TRACET
one™ Tester and Accessories
62-140
VDV MultiMedia Cable Tester
Easy-to-use tester f
or installers working
with voice, data and video applications.
One tester for all applications!
n Voice — supports 3-pair USOC
and 6-position RJ-11/12 jacks for
telephone cable testing
n Data — supports both shielded and
unshielded cable testing to T568A/B
(RJ-45)
n Video — tests coax cable for opens
and shorts with F-connector interf
ace
n Tests for opens, shorts, miswires,
reversals and split pairs. Also indicates
correct wiremap. Has automatic shut
off (to prolong battery life) and low
battery indicator.
n Easy-to-read LCD display with “PASS/FAIL” indicator after each
test
n Tone generator supports four different tones making fault isolation
easier
n One remote wiremap and testing unit is stored inside tester —
easier to keep all parts together
n Uniquely designed remote accommodates RJ-11, RJ-45 and
F-style connectors
Description Cat. No.
Kit with integrated remote and accessories 33-856
Smart6™ Modular Tester
n 6-position Tester
n Incoming call identification
Description
Cat. No.
Smart6™ Modular T
ester
62-096
LinkMaster™ Tester
Tests wiring configurations on
UTP/STP cables. Checks for
shorts, miswires, reversals and
split pairs. Debug feature,
automatic shut-off and low
battery LED indication.
n Designed to test installed
twisted pair wiring
n Tests unshielded and shielded
modular plugs
n Main unit and r
emote allow one
person testing
Description Cat. No.
LinkMaster™ Tester and Remote 62-200
NEW
Design
NEW
Design
62-164 62-160
33-916 33-917
Also available in these kits:
Section G - DataComm 10/22/08 8:20 AM Page 9
Compression Tools
www.idealindustries.com 1-800-435-0705 for Customer Service
G-10
OmniSeal™ Pro Compression Tools
n Easily compr
esses series 6 and 59 coax
compr
ession F-connectors
n Permanent connection – never
comes loose
n Works with most br
ands of
compression connectors
Economy Compression Tool
OmniSeal Pro
30-603
OmniSeal Pro XL
30-793
High strength aluminum
body for durability
and long life
Compresses F-type,
Mini F-type, RCA, and
Mini RCA connectors
Adjustable to fit
multiple cables
and connectors
The new IDEAL OmniSeal™ Compression Tools now offer additional features and increased
connector compatibility in a smaller, more compact tool designed to meet the demands of
the pr
ofessional installer. (OmniSeal requires no accessory attachment to terminate IDEAL
branded compression connectors.) Most other manufacturers compression connectors
can be terminated with an easy plunger depth adjustment. The simple intuitive design
combined with its size and universal connector acceptance makes this the only
compr
ession tool needed by professional installers.
n Factory preset to work with IDEAL compression connectors
n Compresses F-type, RCA, BNC and Mini connectors
n Adjustable to fit other manufacturer’s connectors — no accessory
adapters required
n Connectors approved for use by satellite and cable TV companies
Convenient
handle lock
for easy fit
in pouch
For BNC
connectors
(Model 30-793)
BNC F-Type RG11 RCA Mini Coax
OmniSeal™ Pro XL
30-793
OmniSeal™ Pro
30-603
Description Qty. Cat. No.
OmniSeal™ Pro XL Compression Tool 1 30-793
OmniSeal™ Pro Compression Tool 1 30-603
User-friendly spring
loaded handle
Textured Santoprene
™
slip resistant comfort
grip
Handy 7/16”
hex socket
for easy
connector
to cable
installation
Description
Cat. No.
Economy Compression T
ool
30-633
Economy Compression T
ool Kit - Includes four RG-6
Connectors
33-633
33-630 33-624 33-945
Also available in these kits:
Section G - DataComm 10/22/08 8:20 AM Page 10
30-587
RG-58, RG-174 and RG-8218 for both
50 and 75 ohm cables (Hex 0.213
(5.41mm), 0.178 (4.52mm), 0.068
(1.73mm), 0.042 (1.07mm)
Tool w/die N/A
30-591
Plenum and Non-Plenum Thinwire
Cables RG-58 and 59 (Hex, 0.213
(5.41mm), 0.190 (4.83mm), 0.068
(1.73mm), 0.042 (1.07mm)
Tool w/die N/A
30-593
Mini UHF and BNC/TNC 5 cavity
(Hex, 0.052 (1.32mm), 0.068 (1.73mm),
0.100 (2.54mm), 0.213 (5.41mm),
0.255 (6.48mm)
Tool w/die N/A
30-594
Fully Insulated quick disconnect
terminals with thinner wire barrels
22-10 AWG (.324mm
2
- 5.261mm
2
)
Tool w/die N/A
30-599
30-18 AWG (.205mm
2
- 2.08mm
2
)
Open Barrel Pins and Sockets
Tool w/die N/A
30-479 (Tool w/die)
For insulated terminals, 22-10 AWG
with built-in locator
30-556
RJ-11 Crimp Tool for two, four or
six-position modular plugs
Tool w/die N/A
30-559
RJ-45 Eight-position Crimp Tool
for keyed or non-keyed modular
plugs
Tool w/die
30-522
30-560
RJ-45 Eight-position Crimp Tool
for AMP RJ-45 modular plugs
Tool w/die
30-521
30-570
RG-6, RG-174, Belden-Type
RG-8281 cables (Hex. 0.324
(8.23mm), 0.178 (4.52mm),
0.068 (1.73mm)
Tool w/die N/A
30-572
16-26 AWG (1.31mm
2
- .128mm
2
)
miniature insulated rings, spade
and butt splices
Tool w/die N/A
30-573
Cambridge CP-88, CP-89 BNC/TNC
coax connectors with RG-58,
RG-59/RG-62 AU cables (Hex 0.305
(7.75mm), 0.068 (1.73mm), 0.228
(5.79mm)
Tool w/die 30-481
30-576
RG-174, Mini 59 BNC/TNC
Connectors (Hex, 0.178 (4.52mm),
0.128 (3.25mm), 0.068 (1.73mm)
Tool w/die 30-485
DataComm Equipment
Crimpmaster™ Crimp Tools & Die Sets
Crimp Tools/Die Sets
1-800-435-0705 for Customer Service www.idealindustries.com
G-
11
Dies change quickly and easily
with a scr
ewdriver.
Inter
changeable dies
pr
ovide versatility
in a single tool
Pressure adjustment
f
or actuation force
Ratchet crimp action
pr
ovides repeatable and
r
eliable terminations
Crimp release provides
oper
ator safety
High quality ratchet-type crimp tool for electricians, contractors and installers who require guaranteed repeatability of good mechanical and
electrical connections.
Description Cat. No.
Crimpmaster™ Crimp Tool Frame 30-506
30-577
N-Series and RG-8/11 Connectors
(Hex, 0.429 (10.90mm), 0.100
(2.54mm), 0.080 (2.03mm)
Tool w/die 30-482
30-578
RG-59, RG-6, and 8281 50 and 75
OHM cables (Hex, 0.324(8.23mm),
0.255 (6.48mm), 0.068 (1.73mm),
0.042 (1.07mm)
Tool w/die 30-483
30-579
22-10 AWG (.324mm
2
- 5.261mm
2
)
insulated terminals/color coded
nests
Tool w/die 30-500
30-580
22-8 AWG (.3mm
2
- 8mm
2
)
non-insulated terminals
Tool w/die N/A
30-581
RG-58, RG-59/62, BNC/TNC Coax
Connectors (Hex, 0.255 (6.48mm),
0.213 (5.41mm), 0.068 (1.73mm)
Tool w/die 30-502
30-582
F-type CATV RG-59, RG-6
Connectors (Hex, 0.350 (8.89mm),
0.320 (8.13mm), 0.255 6.48mm)
Tool w/die 30-503
30-586
22-12 AWG (.324mm
2
- 3.31mm
2
)
Non Insulated Open Barrel
Connectors, Commercial Type
Tool w/die N/A
Also available in these kits:
33-400 33-917
Section G - DataComm 10/22/08 8:21 AM Page 11
Tools
www.idealindustries.com 1-800-435-0705 for Customer Service
G-12
35-495
110 Blade
Punch Down Tools
35-485
35-492
35-185
Impact Turn-Lock™ Punch Down Tools Cat. No.
Punchmaster™ II Punch Down Tool - body only 35-483
Punchmaster™ II Punch Down Tool w/110 blade 35-485
Punchmaster™ II Punch Down Tool w/66 blade 35-487
Non-Impact Turn-Lock™ Punch Down Tools Cat. No.
Punch Down Tool w/110 blade 35-492
Punch Down Tool w/66 blade 35-493
Economy Punch Down Tool Cat. No.
Non-impact Tool w/permanent non-cut blade 35-185
35-407
110/66 Blade
35-497
66 Blade
35-478
Krone
®
Blade
35-479
Bix
®
Blade
Removable Blades* Cat. No.
110 Turn-Lock™ blade 35-495
66 Turn-Lock blade 35-497
110/66 combo blade w/cutting edges 35-407
Krone
®
blade 35-478
Bix
®
blade 35-479
*Not applicable for Economy Punch Down tool.
Bix
®
is a registered trademark of Nortel. Krone
®
is a registered trademark of Krone, Inc.
Kit Tool Only
Description Cat. No. Cat. No.
Tool for RJ-11 (1, 2, 3 pair) and RJ-45 (4 pair) Plugs 33-700* 30-496
Tool for RJ-45 (4 pair) & DECconnect MMJ (RJ-11, 3 pair) N/A 30-497
T
ool for RJ-11 (1, 2, 3 pair) & DECconnect MMJ
(RJ-11, 3 pair)
N/A
30-498
T
ool for RJ-22 (handset) and RJ-11 (1, 2, 3 pair)
N/A
30-499
Replacement Cut and Strip Blade Set for T
elemaster™
N/A
LB-1747
Kit includes 10 each, RJ-45 8P8C, RJ-11 6P6C and RJ-11 6P4C modular plugs.
Telemaster™ Telephone Tools
n For paired conductors
n Multi-function telephone
tool cuts, strips and crimps
for easy one-tool application
n Steel fr
ame f
or long-term dur
ability
. (Crimps primary modular
plug str
ain r
elief only)
n For paired conductors
n Ratchet version of popular
Telemaster™ Tool for RJ-45
and RJ-11 modular plugs
n Repeatable crimp action f
or
consistent, high quality connections
Ratchet Telemaster™
Description
Cat. No.
Ratchet T
elemaster™
30-696
Replacement
Cut & Strip Blade Set for 30-696
LA-4102
Modular Plug Tool Kit
n Multi-function telephone/network
tool; cuts, strips and crimps
n Steel fr
ame construction
for durability
n Inter
changeable dies allow f
or
crimping RJ-45 and RJ-11 modular plugs
n Tool-less die change for added convenience
n Spring return handle for comfort
Description Cat. No.
Modular Plug Tool Kit 33-296
33-505
33-704 33-750
33-705
Also available in these kits:
Also available in these kits:
Section G - DataComm 10/22/08 8:21 AM Page 12
Tools
DataComm Equipment
1-800-435-0705 for Customer Service www.idealindustries.com
G-
13
Description Cat. No.
Kinetic Super™ Wire Stripper/Crimper 45-719
n Easily cuts and strips
22 to 24 AW
G solid
wire
Kinetic Super™ Wire
Stripper/Crimper
35-465
Description Cat. No.
20-26 AWG (.519 mm
2
- .128 mm
2
) RS232 D-sub
35-465
Round Barrel Contacts, Pins or Sockets
16-22 AWG (1.31 mm
2
- .324 mm
2
) Round Barrel
35-466
Contacts, Pins, Sockets and Deutsch 16 Pin Contacts
Trompeter BNC Connector Center Pins 35-468
4-Way Indent Crimp Tools
Crimp solid barr
el contacts for
RS232 interface connectors.
Feature four-way indent dies
(per M
S22520 specifications),
full cycle ratchet, built-in pin and
socket locator and comfort-grip handles.
n High-grade steel construction for outstanding performance
D-Sub/Double-D Service Tool
Description Cat. No.
D-Sub/Double-D Service Tool 30-426
n Exact r
eplacement of the AMP open-
barrel service tool for stamped
contacts and D-Sub contacts
n Also crimps
Double-D, high
density, miniature
contacts
n Includes openings for crimping insulated terminals and cutters for
machine screws
Coax Strip and Crimp Tool
n
Precision, form-ground stripping
holes remove outer jacket
and insulation from
RG-59 and RG-6
coaxial cable
n
Durable blades cut
copper-coated steel
conductors
n
Three crimping nests for crimping F-connectors and ring terminals
n
Cushioned, comfort-grip handles
Description Cat. No.
Coax Strip & Crimp Tool 30-433
Coax Strip & Crimp Tool Kit w/ten RG-6 F-Connectors 30-433F
Section G - DataComm 10/22/08 8:21 AM Page 13
Coax Stripmaster
®
Wire Strippers
Strippers
www.idealindustries.com 1-800-435-0705 for Customer Service
G-14
Typical
Description RG Cables Cat. No.
Coaxial Cable Stripper, RG-174, 45-162
up to 1/8 in. (3.2mm) O.D RG-187 (Gray)
Coaxial Cable Stripper, RG-58,CB 45-163
1/8 in. (3.2mm) to 7/32 in. (5.556mm) O.D. Mini Coax (Blue)
Coaxial Cable Stripper, 1/4 in. (6.4mm) to 45-164
9/16 in. (14.3mm) O.D.
RG-11, RG-8
(Blue)
Cable Stripper, 3/16 in. (4.8mm) to 5/16 in. RG-59, 45-165
(8mm) O.D. UTP Cable (Black)
Replacement Blade Set* for 45-162,
45-163, 45-165
__
L-9225
Replacement Blade Set* for 45-164
__
L-9226
*A set of blades consists of three straight blades and one round blade.
UTP/STP/Coaxial Cable Strippers
Mini Coax Stripper
RG-11 Coax Strippers
n Adjustable stripper for mini
coax cable
n Provides a 1/4 in. x 1/4 in.
strip
Description Cat. No.
Mini Coax Stripper 45-529
Coax Cable Repl. Blade
Description Type (RGU) Cat. No. Cat. No.
Coax Stripmaster
®
for RG-6 RG-6 LB-740 45-262
Coax Stripmaster
®
for RG-59 RG-59 LB-743 45-265
Coax Stripmaster
®
for RG-6 RG-6
LA-3953 45-282
Quad Shield Quad Shield
n P
rovides precision stripping with easy spring
cushion grip
n Knif
e-type blades feature multiple hole
diameters sized for two step removal of outer
jacket insulation and center conductor
45-162 45-163 45-165
45-164
45-011
Multi-Strip Coax/UTP Cable Stripper
n Strips UTP, RG-59 and RG-6 coax cable
n P
rovides a 1/4 in. (minimum) x 1/4 in.
strip on coax
n Spare cartridge compartment
provided
n P
ush-on ring for easy
connector termination
n RG-11 45-011 Coax Stripper - for use with IDEAL RG-11 push-on
connectors, provides a 1/4 in. x 1/8 in. strip
n R
G-11 45-111 Coax Stripper - f
or use with I
D
E
A
L R
G-11
compr
ession connectors, provides 1/4 in. x 1/4 in. strip
Description Cat. No.
Coax/UTP Cable Stripper 45-603
RG-6/59 Replacement Cartridge LB-2726
RG-7/11 Replacement Cartridge LB-2728
UTP Replacement Cartridge LB-2727
Description
Cat. No.
RG-11 Coax Stripper for Push-On Connectors 45-011
RG-11 Coax Stripper for Compression Connectors 45-111
NEW
n Adjustable blades can be set for any depth to help ensure nick-
free stripping and slitting of cables
45-111
Section G - DataComm 10/22/08 8:22 AM Page 14
Strippers
DataComm Equipment
1-800-435-0705 for Customer Service www.idealindustries.com
G-
15
Description Cat. No.
Coax Stripper for RG-8/11U 45-510
Coax Stripper for RG-6 45-513
Toggle
®
Coax Strippers
UTP Cable Stripper
Description Cat. No.
UTP Cable Stripper 45-167
Coax Cable Stripper
n Toggle
®
Tools for stripping Ethernet,
T
hinnet, RG-62 or RG-59 coax cable
and other cable sizes
n Strips Cat 3, 5, 5e & 6 cables
n One-step stripping
n For RG-6, RG-6 Quad and RG-59
n No adjustment required
n Strips center conductor and
cable jacket
Description Cat. No.
Coax Cable Stripper 45-320
Coax Connector Kit w/four Push-On F-Connectors 33-320
Description Cat. No.
Data Cable Stripper for unshielded and shielded twisted pair cable 45-514
Cyclops
®
Data Cable Stripper
n Fast, easy removal of outer sheath
insulations (PVC and Plenum types,
UTP & STP)
Simplex/Duplex 3mm
Jacket Stripper
n Designed to remove the jacket from 3mm Simplex or Duplex (zip
cord) fiber optic cable
n Form-ground, knife-type blades for accurate easy stripping without
damaging the fiber or Kevlar
®
strength member
n Contoured, comfort-grip handles to reduce operator fatigue
Description Cat. No.
Simplex/Duplex 3mm Jacket Stripper 45-349
Note: Kevlar
®
is a registered trademark of DuPont.
Description Cat. No.
Round Cable Slitting and Ringing Tool 45-144
Replacement Blades for 45-144 (2/pkg.) LB-1748
n Cuts around cable jacket as well as
slits the length of jacket for
easy removal
n Use with single or multiple
conductor cable up to
1.75 in. O.D.
n Blade adjusts for jacket thicknesses up to .125 in.
n Spare blade in handle base
Round Cable Slitting and Ringing Tool
Replacement
Description Cassette Cat. No.
Coax Stripper - 2 Step
• For most IDEAL compression connectors and 45-524
45-526
single crimp/twist-on BNC/TNC (Blue)
• Strips 0.250 in. or 6.35mm
Coax Stripper - 3 Step
• For crimp BNC and TNC connectors
45-522
45-520
• Strips braid 0.240 in. or 6mm and (Black)
Dielectric 0.240 in. or 6mm
Coax Stripper - 3 Step
• For dual crimp BNC/TNC and Thinnet BNC conn.
• For 735A Belden
®
cable 45-523
45-521
• Strips braid 0.328 in. or 8.2mm and
(Brown)
dielectric 0.109 in. or 2.7mm
Coax Strippers
n Specific adjustments
needed for each cable
size
1/4 in. x 1/4 in. standard strip.
1/4” 1/4”
Section G - DataComm 10/22/08 8:22 AM Page 15
Cutters/Scissors
G-16
www.idealindustries.com 1-800-435-0705 for Customer Service
Data T
®
-Cutter
Description Cat. No.
Data T
®
-Cutter 45-074
Data T
®
-Cutter II 45-075
Description
Cat. No.
Multi Conductor Cable to .500 in. (12.7mm)
35-051
Solid or Stranded
Economy Round Cable
and Wire Cutter
n Cuts multi-conductor cable
up to .5
00 in. (1
2.7mm)
and solid or stranded
wire up to #8 AWG
(1
0mm
2
)
n Built-in return spring, locking latch
n Stamped, hardened steel frame with curved cutting blades
Center Conductor Cutter
n Trims coax center conductor to
3/16 in. (4.8 mm) length for
pr
oper installation into a dual
crimp coax connector.
Lever™ -Snips Electrician’s Scissors
with Stripping Notches
n Er
gonomic design giv
es
added lev
er
age
n Spring-action, mechanical
advantage increases stripping
leverage and reduces operator fatigue
n Double plated f
or added rust pr
otection
n Extr
a-deep serr
ations grip wir
e better
Description Cat. No.
Electrician’s Scissors with Stripping Notches 35-087
Electrician’s Scissors
n Cuts round communication cable and maintains cable geometry for
better cable performance
n Cuts multi-pair cable up to .5
00 in. (12.7mm) and coaxial cable up to
RG-9/U
n Suitable for soft cables (not ACSR)
n Steel reinforced center conductors can be trimmed with bolt cutting
holes
n Locking latch keeps tool closed in pouch
n Data T
®
-Cutter I
I designed for RG-59 and RG-6 coaxial cable
n Designed for use in telephone and electrical service applications
n Cut up to 16 AWG solid and 12 AWG stranded wire
n Serrated surface on back blade edge cleans wire
n Electrician’s Scissors with stripping notches strip 19 and 23 AWG wire
35-088
35-089
Description Cat. No.
Center Conductor Cutter 35-060
Description Cat. No.
Electrician’s Scissors w/stripping notches 35-088
Electrician’s Scissors 35-089
Cable Splicing Knife and Leather Holder 35-091
Leather Knife Holder Only 35-092
Cable Splicing Kit (Scissors, Splicing Knife, Leather Holder) 35-093
Leather Holder only for Scissors and Knife 35-094
35-093
45-074
45-075
33-917 33-623
Also available in these kits:
Section G - DataComm 10/22/08 8:22 AM Page 16
Splitters
DataComm Equipment
1-800-435-0705 for Customer Service www.idealindustries.com
G-17
Surge Suppression Cable Splitters
4-Way Digital Surge Suppression Cable Splitters withstand a one-time surge up to 6KV on cable line
Q Bandwidth: 5 MHz - 1 GHz
Q Impedance: 75 ohm
Q Over 130 dB of RFI Shielding
Q Low 8 db Insertion Loss
Description Cat. No.
2-Way Surge Suppression Splitter 85-135
4-Way Surge Suppression Splitter 85-137
Grounding Blocks
Q Solid zinc alloy, nickel plated and chromate finished
Q High Performance beryllium copper contact
Q Excellent electrical performance 0 - 3,000 MHz
Q Dual grounding holes can accept up to #6 wire
Q UL/CSA approved
Description Qty. Cat. No.
3 GHz Double Grounding Block 1/card 85-311
3 GHz Quad-Square Grounding Block 1/card 85-313
85-311
85-313
Satellite and Digital TV Splitters
Description Qty. Cat. No.
2-Way, 5MHz - 2.3GHz 1 85-332
3-Way, 5MHz - 2.3GHz 1 85-333
4-Way, 5HMz - 2.3GHz 1 85-334
85-332
85-333
85-334
Description Quantity Cat. No.
CATV Cable Splitter, 5-900 MHz, 2-Way Card of 1 85-032
CATV Cable Splitter, 5-900 MHz, 3-Way Card of 1 85-033
CATV Cable Splitter, 5-900 MHz, 4-Way Card of 1 85-034
High Performance Cable Splitter,
Card of 1 85-132
5MHz-1GHz 2-Way
Box of 10 86-132
High Performance Cable Splitter,
Card of 1 85-133
5MHz-1GHz 3-Way
Box of 10 86-133
High Performance Cable Splitter,
Card of 1 85-134
5MHz-1GHz 4-Way
Box of 10 86-134
Splitters
85-132 85-134
Description Cat. No.
Digital Cable Splitter, 8-Way 85-138
Digital Cable Splitter
Q Nickel-plated housing
Q High-performanceimpedance-balanced
Printed Circuit Board design
Q Bandwidth: 5MHz - 1 GHz Impedance: 75 Ohm; over 120 dB of
RFI shielding; Splits signals up to 8 outlets
Diplexer, 2.3 GHz
Q Combine or split cable/antenna signals
with satellite signals
Q High quality PCB design
Q Nickel-plated die-cast zinc housing
Q Grounding hole for up to 6 AWG wire
Q PCB Printed Circuit Board Design
Q Nickel Plated Housing
Q Splits signals up to 4 outlets
85-133
Description Cat. No.
Diplexer, 2.3 GHz, SATV/TV Combiner Splitter - 2 Amp 85-323
Q Designed for easy mounting over cable
Q All ports are F female connectors, 75Ω
Q Two grounding screws eliminate the need for grounding block
Q Single port power pass
Terminators (85-038) needed for all unused
ports for optimal performance
www.idealindustries.com 1-800-435-0705 for Customer Service
G-18
Compression Connectors for Every Application
Reg/Tri/Quad & Plenum F-Connectors
• Fits 60% regular, tri-shield and quad cables
• Nickel-plated, brass-construction for superior corrosion resistance
•
Approved for use by satellite and cable TV companies
•
Approved for indoor and outdoor use
•
Use 30-603, 30-793 or 30-633 Compression Tools
RG-11 F-Connectors
• Fits 60% regular RG-11 cable
• Nickel-plated, brass-construction for superior corrosion
resistance
• Approved for use by satellite and cable TV companies
• Approved for indoor and outdoor use
• Use 30-603 or 30-793 Compression Tools
OmniCONN™ F-Connectors
•
Non corrosive nickel plated brass body and polyc
arbonate bushing
•
Delrin/Nylon adapter sleeve and o-ring provide double protection for
a water
tight seal
• Free spinning hex nut for ease of installation onto all 7/16 ports
• 75 ohm nominal impedance
• Bandwidth up to 3 GHZ
Mini R
CA Connectors
• For use with most 21-25 AWG mini coax cable
• Body is nickel plated for outstanding corrosion resistance
•
Mini R
CA head is gold plated for superior cont
act per
formance
• Bandwidth is 5 MHz - 3 GHz, Impedence is 75 Ohms (nominal),
return loss min. -30 dB @ 3 GHz
R
CA
Connectors
•
Constructed of nickel plated brass and gold plated head
• 75 ohm nominal impedance
• Bandwidth up to 3 GHZ
• Compatible with 30-603 and 30-793 Compression Tools
F-Connector
RCA
Connector
BNC Connectors
• Nickel-plated, brass-construction for superior corrosion resistance
• Moisture-inhibiting design
• Approved for indoor and outdoor use
• Use 30-793 Compression Tool
• 75 Ohm nominal impedance
• Gold-plated pin contact area
NEW
Section G - DataComm 10/22/08 8:32 AM Page 18
DataComm Equipment
Connectors/Port Seals
G-19
1-800-435-0705 for Customer Service www.idealindustries.com
Compression Connectors
Compression Port Seals
Connector Type Cable Type Qty. Cat. No.
Card of 4 92-654
RG-6
Card of 10 92-651
F
Reg/Tri/Quad
Jar of 50 92-650
Jar of 100 92-656
Box of 1,500 92-659
F
RG-6
Jar of 50 92-660
Plenum
Box of 1,500 92-669
F
RG-59
Jar of 50
92-610
Reg/Tri/Quad
Box of 1,500
92-619
F RG-11
Card of 10
89-211
Box of 500 89-1211
F RG-6
Card of 4 89-017
Jar of 50 89-044
F
RG-6
Card of 4
89-018
Quad
Jar of 50 89-045
BNC RG-6
Card of 15 89-048
Jar of 35 89-5048
BNC RG-59
Card of 15 89-047
Jar of 35 89-5047
RCA RG-6
Card of 10 89-582
Jar of 35 89-580
RCA RG-59
Card of 10 89-572
Jar of 35 89-570
F Mini Card of 10 89-014SM
RCA Mini Card of 10 89-014SMRCA
n Used with compression F-connectors to weatherproof connector
by placing onto the female port
n Made from EPDM for superior sealing
Description Qty. Cat. No.
Short Sleeve Compression F-Connector Port Seals Bag of 100 89-126
Long Sleeve Compression F-Connector Port Seals Bag of 100 89-127
Long Sleeve
Short Sleeve
33-635 33-630
Also available in these kits:
33-620
Section G - DataComm 10/22/08 8:32 AM Page 19
Connectors
www.idealindustries.com 1-800-435-0705 for Customer Service
G-20
Description
Qty. Cat. No.
RG-11 Push-on F-Connector Card of 10 85-111
RG-11 Push-on F-Connector Box of 500 85-0111
Connector Type Cable Type Qty. Cat. No.
Card of 4 85-065
F
RG-6
Jar of 50
85-165
Box of 1,500 85-1165
Card of 4 85-066
F RG-6 Quad Jar of 50 85-166
Box of 1,500 85-1166
Card of 4 85-067
F RG-59 Jar of 50 85-167
Box of 1,500 85-1167
Description
Cat. No.
Coax Connector Kit w/Economy Coax Stripper and four
33-320
RG-6 Push-on Connectors
Connector Type Cable Type Termination Type Quantity Cat. No.
Card of 4 84-017
Card of 10 85-037
F RG-6 Crimp
Card of 50 85-017
Box of 100 86-017
Card of 4 84-030
Card of 10 85-057
F
RG-6 Quad Crimp
Card of 50
85-030
Box of 100 86-030
Card of 4 84-016
F
RG-59 Crimp Card of 10
85-036
Card of 50 85-016
Card of 4 84-039
Card of 10 85-053
F RG-6 Twist-On
Card of 50 85-039
Box of 100 86-039
F RG-59 Twist-On
Card of 4 84-018
Card of 10 85-035
F N/A N/A Card of 10 85-031
F N/A N/A Card of 10 85-038
F-Type Coaxial Connectors
Push-On F-Connectors, RG-6 & RG-59 Push-On F-Connectors, RG-11
n Tool-less design - cuts, strips and pushes on to cable
n All brass nickle-plated construction
n Knurled nut for superior grip
n For indoor use
n Fits regular RG-11 cable
n Innovative design does not
require a compression or
crimp tool
n Integral pin with center
conductor seizing
mechanism
n Manufactured from solid brass,
nickle-plated for durability
n 9/16 in. hex nut
n Use 45-011 1/4 in. x 1/8 in. Coax Stripper
F-Series Connectors utilize threaded couplings and cable conductors as contacts for CATV and other UHF applications.
Connector Removal Tools
Description Cat. No.
F & BNC Coax Connector Removal Tool - 8 in. 35-046
F & BNC Coax Connector Removal Tool - 12 in. 35-042
F & BNC Coax Connector Removal Tool - 16 in. 35-043
IDEAL
•
•
L
I
F
E
T
I
M
E
G
U
A
R
A
N
T
E
E
35-043
35-046
35-042
n Works on compression and hex connectors
n New comfort grip handle aids in installing and removing connectors on coax cable
NEW
Section G - DataComm 10/22/08 8:33 AM Page 20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

3com 45-338 User manual

3com
Brand
3com
Model
45-338
Category
Cable network testers
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents