Project __________________________________
Item ____________________________________
Quantity ________________________________
CSI Section 11400
Approved _______________________________
Date ____________________________________
980 S. Isabella Rd.
Mt. Pleasant, Michigan 48858
Phone: 800-733-8948 or 989-773-7981
Fax: 800-669-0619
www.delfield.com
Exterior top is one-piece, 22-gauge stainless steel with
integral square nosing on the front.
Exterior back and bottom are two-piece 24-gauge galvanized
steel.
Exterior ends are stainless steel.
Interior sides are thermoformed ABS plastic with shelves
supported on plugs. Interior back is one -piece 22-gauge
stainless steel. Interior bottoms are thermofoamed ABS
plastic. Base is fully insulated with high-density foamed in
place environmentally friendly, Kyoto Protocol Compliant, Non
ODP (Ozone Depletion Potential), Non GWP (Global Warming
Potential) polyurethane.
Refrigeration system uses HFC-404A refrigerant. Compressor
is 1/3 H.P., with condenser coil and hot gas condensate
evaporator mounted on rear of the cabinet. Evaporator coils
are located on the interior rear wall of the cabinet. Refrigerant
flow is controlled by a capillary tube. Cabinet maintains an
interior cabinet temperature of 36°F to 40°F (2°C to 4°C).
Electromechanical control is mounted on the right side of
the evaporator housing inside the cabinet. It allows the unit to
maintain consistent temperatures in heavy duty conditions.
Electrical connection is 115 volt, 60 Hertz, single phase. Unit
has a 7’ (2.1m) long electrical cord and NEMA 5-15P plug.
Casters: Equipment is mounted on 5” (13cm) diameter plate
casters with front two locking. Equipment clearance above the
floor is 2.5” (6cm).
Door has a 24-gauge stainless steel exterior, with thermoformed
ABS plastic interior liner.
Drawers have 24-gauge stainless steel exterior with
thermoformed ABS plastic interior liner. Drawer frames are
12-gauge stainless steel. Drawer slides are 11-gauge stainless
steel with Delrin bearings. Top drawer holds two full size 12”
x 20” (30.5cm x 50.8cm), 4”-6" (10.2cm-15.2cm) deep pans.
Bottom drawer holds two full size 12 x 20", 4” deep pans. Pans
are supplied by others.
Specifications
Standard Features
Options &
Accessories
All 4400 and 4500 Series units are 100% front
breathing, which allows the unit to be pushed
against a wall or built into a cabinet or an
existing line up
Durable, rugged stainless steel sides, top and
front
Features Delfield’s exclusive ABS interior (on
sides). ABS is extremely durable - it won’t dent,
chip or corrode and is backed by a limited
lifetime warranty
Heavy duty self-closing hinges
“D” prefix models feature Delfield’s exclusive
new drawer system. Drawers are backed by a
10-year warranty on the track assembly
Environmentally friendly R404A refrigerant
High density foamed in place environmentally
friendly, Kyoto Protocol Compliant, Non ODP
(Ozone Depletion Potential), Non GWP (Global
Warming Potential) polyurethane keeps energy
costs low
Black recessed quick grip handle
Standard on 5” casters for easy cleaning and
installation
60-cycle single phase electrical system
•
•
•
•
•
•
•
•
•
•
4464N Two section refrigerator with doors
D4464N Two section refrigerator with drawers
•
•
Models
4464N Flat Top
Front-Breathing Self-Contained Flat Top Refrigerated
Bases
4464N Flat Top: Front-Breathing Self-Contained Flat Top Refrigerated Bases
7’ cord and plug supplied
One epoxy coated wire shelf standard,
installed per door section
Electromechanical control
One year parts and 90 day labor
standard warranty
18” wide single tier overshelf
Stainless steel finish on back
Plastic laminate on front
Additional wire shelves
Door lock
Exterior thermometer (door models
only)
Interior lights
Glass door(s)
220V/50 Hertz electrical system*
Inclusion of this option will alter
electrical specifications of the unit
•
•
•
•
•
•
•
•
•
•
•
•
•
*
4464N
