Toshiba SD-K750SU User manual

Category
DVD players
Type
User manual
DVD/CD PLAYER
SD-K750SU
OWNER’S MANUAL
DIGITAL VIDEO
© 2005 Toshiba Corporation
Before operating the unit, please read this manual thoroughly.
2F10101A [E] COVER 1/18/05, 6:36 PM1
2
SAFETY PRECAUTIONS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION:
OUT PUT
L
R
P
B
P
R
COAXIAL
S-VIDEO
DIGITAL AUDIO AUDIO
VIDEO
Y
COMPONENT
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE.
DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications made to this equipment, not expressly approved by Toshiba, or parties
authorized by Toshiba, could void the user’s authority to operate the equipment.
CAUTION: Servicing instructions are for use by qualified service personnel only. To reduce the risk of electric
shock do not perform any servicing other than that contained in the operating instructions unless you
are qualified to do so.
CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CARE-
FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE,
CONTACT AN AUTHORIZED SERVICE LOCATION.
USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE.
VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT
STARE INTO BEAM.
The lightning flash with arrowhead symbol, within an equilat-
eral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of elec-
tric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accom-
panying the appliance.
Location of the required Marking
The rating sheet and the safety caution are on the
rear of the unit.
CERTIFICATION: COMPLIES WITH FDA RADIA-
TION PERFORMANCE STANDARDS, 21 CFR
SUBCHAPTER J.
In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video player.
Model No. Serial No.
Retain this information for future reference.
2F10101A [E] P02-05 1/18/05, 6:36 PM2
3
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS PROVIDED IN THIS
OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following
procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that
can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
IMPORTANT SAFEGUARDS
2F10101A [E] P02-05 1/18/05, 6:36 PM3
4
10.Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
S3125A
11.Only use attachments/accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13.Unplug this apparatus during lightning storms or when unused for long periods
of time.
14.Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15.When you use headphones on the amplifier, keep the volume at a moderate
level. If you use the headphones continuously with high volume sound, it may
cause hearing damage.
IMPORTANT SAFEGUARDS (Continued)
2F10101A [E] P02-05 1/18/05, 6:36 PM4
5
16.Do not overload wall outlets; extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
17.Never insert objects of any kind into this apparatus through openings as they
may touch dangerous voltage points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the apparatus.
18.Keep your fingers well clear of the disc tray as it is closing. Neglecting to do
so may cause serious personal injury.
19.Do not place a heavy object on or step on the apparatus. The object may fall,
causing serious personal injury and serious damage to the apparatus.
20.Do not use a cracked, deformed, or repaired disc. These discs are easily
broken and may cause serious personal injury and apparatus malfunction.
2F10101A [E] P02-05 1/18/05, 6:36 PM5
6
Introduction
Notes on handling
When shipping the DVD video player, the original
shipping carton and packing materials come in handy.
For maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the DVD video player. Do not leave rubber or plastic
products to contact the DVD video player for prolonged
period. They will leave marks on the finish.
The top and rear panels of the DVD video player may
become warm after a long period of use. This is not a
malfunction.
When the DVD video player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD video player for a long
period, the unit may not function properly in the
future. Turn on and use the DVD video player
occasionally.
Notes on locating
Place the DVD video player on a level surface. Do not
use it on a shaky or unstable surface such as a
wobbling table or inclined stand. The loaded disc may
become disaligned and damage the DVD video
player.
When you place this DVD video player near a TV,
radio, or VCR, the playback picture may become poor
and the sound may be distorted. In this case, place
the DVD video player away from the TV, radio, or
VCR.
Notes on cleaning
Use a soft, dry cloth for cleaning.
Use a dry cloth to wipe it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD
video player.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
Notes on moisture condensation
Moisture condensation damages the DVD video
player. Please read the following carefully.
Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the optical pick-up lens
inside this unit, one of the most crucial internal parts of
the DVD video player.
Moisture condensation occurs during the following
cases.
When you bring the DVD video player directly from a
cold place to a warm place.
When you use the DVD video player in a room where
you just turned on the heater, or a place where the
cold wind from the air conditioner directly hits the unit.
In summer, when you use the DVD video player in a
hot and humid place just after you move the unit from
an air conditioned room.
When you use the DVD video player in a humid place.
Do not use the DVD video player when moisture
condensation may occur.
If you use the DVD video player in such a situation, it
may damage discs and internal parts. Remove the
disc, connect the power cord of the DVD video player
to the wall outlet, turn on the DVD video player, and
leave it for two or three hours. After two or three
hours, the DVD video player will have warmed up and
evaporated any moisture. Keep the DVD video player
connected to the wall outlet and moisture
condensation will seldom occur.
E
x
a
m
p
l
e
o
f
m
o
i
s
t
u
r
e
c
o
n
d
e
n
s
a
t
i
o
n
!
Optical pick-up
lens
It’s too
warm!
Wait!
Precautions
2F10101A [E] P06-09 1/18/05, 6:36 PM6
7
On handling discs
Do not touch the playback side of the disc.
Do not attach paper or tape to discs.
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
Playback side
DVD video disc
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3
Track 1 Track 2 Track 3 Track 4 Track 5
Structure of disc contents
Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. Video CDs and
Audio CDs are divided into tracks.
DVD video disc
Video CD/Audio CD
Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.
Notes on copyright
The unauthorized recording, use, distribution, or
revision of copyrighted materials including, without
limitation, television programs, videotapes, and DVDs,
is prohibited under the copyright laws, and may subject
you to civil and criminal liability.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
Consumers should note that not all high definition
television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case
of 525 progressive scan picture problems, it is
recommended that the user switch the connection to the
“STANDARD DEFINITION” output. If there are questions
regarding our TV set compatibility with this model 525p
DVD player, please contact our customer service center.
Video CD/Audio CD
Notes on discs
2F10101A [E] P06-09 1/18/05, 6:36 PM7
8
Introduction
DIGITAL VIDEO
About this owner’s manual
This owner’s manual explains the basic instructions of
this DVD video player. Some DVD video discs are
produced in a manner that allows specific or limited
operation during playback. As such, the DVD may not
respond to all operating commands. This is not a defect
in the DVD. Refer to instruction notes of discs.
may appear on the TV screen during operation.
A “
” means that the operation is not permitted by the
DVD or the disc.
For example, sometimes it is unable to stop the playback
of copyright message of the disc when the STOP (3)
button is pressed. Alternatively, the “
may also
indicate that the feature is not available for the disc.
Notes on region numbers
The region number of this DVD is 1. If region numbers,
which stand for their playable area, are printed on your
DVD video disc and you do not find
1
or
ALL
, disc
playback will not be allowed by the player. (In this case,
the DVD will display a message on-screen.)
On Video CDs
This DVD supports Video CDs equipped with the PBC
(Version 2.0) function. (PBC is the abbreviation of
Playback Control.) You can enjoy two playback
variations depending on types of discs.
Video CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this unit in the
same way as an audio CD.
Video CD equipped with PBC function
(Version 2.0)
In addition to operation of a Video CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.
Playable discs
This DVD video player can play the following discs.
You cannot play discs other than those listed above.
You cannot play discs of DVD-RAM, DVD-ROM, Photo
CD, etc., or non standardized discs even if they may be
labeled as above.
Some CD-R/RWs cannot be played back depending on
the recording conditions.
This unit uses the NTSC color system, and cannot play
DVD video discs recorded in any other color system
(PAL, SECAM, etc.).
Because of problems and errors that can occur during the
creation of DVD software and/or the manufacture of DVD
discs, Toshiba cannot guarantee that this player will play
every feature of every DVD bearing the DVD logo. As one
of the creators of DVD technology, Toshiba DVD players
are manufactured using the highest standards of quality,
and as a result, such incompatibilities are rare. If you
happen to experience any difficulty playing a DVD on a
Toshiba DVD player, please feel free to call our Contact
listed in “How to Obtain Warranty Services” (see page 41).
DVD
video
discs
Disc Mark
Contents
Disc
Size
Maximum
playback time
Video
CDs
Approx. 4 hours
(single sided disc)
Approx. 8 hours
(double sided disc)
Approx. 80 minutes
(single sided disc)
Approx. 160 minutes
(double sided disc)
Approx. 74 minutes
Approx. 20 minutes
8 cm
12 cm
8 cm
12 cm
Audio
+
Video
(moving
pictures)
Audio
+
Video
(moving
pictures)
Audio
CDs
Approx. 74 minutes
Approx. 20 minutes
8 cm
(CD
single)
12 cm
Audio
The following discs are also available.
DVD-R/RW discs of DVD video format
CD-R/CD-RW discs of CD-DA, Video CD, SVCD,
MP3, WMA or JPEG format
Kodak Picture CD and FUJICOLOR CD format
Some of these discs may be incompatible.
Notes on discs (continued)
2F10101A [E] P06-09 1/26/05, 10:14 AM8
9
Introduction
SAFETY PRECAUTIONS ........................................ 2
IMPORTANT SAFEGUARDS................................... 3
Precautions ..............................................................6
Notes on discs ......................................................... 7
Table of contents ...................................................... 9
Identification of controls ......................................... 10
Front panel ....................................................... 10
Rear panel ........................................................ 10
Display .............................................................. 11
Remote control .................................................12
Loading batteries .............................................. 13
Operating with the remote control .................... 13
Connections
Connecting to a TV ................................................14
Connecting to a TV ........................................... 14
Connecting to an audio system and TV
equipped with component video inputs ............ 15
Connecting to optional equipment ......................... 16
Connecting to an amplifier equipped with a
Dolby Digital decoder ....................................... 16
Connecting to an amplifier equipped with
Dolby Surround Pro Logic ................................ 16
Connecting to an amplifier equipped with
a DTS decoder ................................................. 16
Connecting to an amplifier equipped with
an MPEG2 audio decoder ................................17
Connecting to an amplifier equipped with
a digital audio input ..........................................17
Basic playback
Playing a disc ......................................................... 18
Basic playback .................................................18
Playing in fast reverse or fast forward directions .
20
Playing frame by frame ....................................20
Playing in slow-motion ...................................... 20
Locating a chapter or track ............................... 20
Advanced playback
Zooming ................................................................. 21
Locating desired scene .......................................... 21
Marking desired scenes ......................................... 22
Marking the scenes .......................................... 22
Returning to the scenes ...................................22
Repeat playback .................................................... 23
A-B Repeat playback ............................................. 23
Program playback .................................................. 24
Random playback .................................................. 24
Changing angles .................................................... 25
Title selection ......................................................... 25
DVD menu.............................................................. 25
Changing soundtrack language ............................. 26
Setting surround sound .......................................... 26
Subtitles ................................................................. 27
To turn off the PBC ................................................. 27
Disc status.............................................................. 27
MP3/WMA/JPEG operation ................................... 28
MP3/WMA/JPEG CD information ..................... 28
MP3/WMA CD playback ................................... 29
JPEG CD playback ........................................... 30
Slide show playback ......................................... 30
Function setup
Customizing the function settings .......................... 31
Setting procedure .............................................31
Setting details ................................................... 32
Temporary disabling of rating level by DVD disc .... 36
Language code list ................................................. 37
Others
Troubleshooting guide ............................................ 38
Specifications ......................................................... 39
Limited warranty ..................................................... 40
Table of contents
2F10101A [E] P06-09 1/27/05, 11:559
10
Introduction
Front panel
Rear panel
Identification of controls
See the page in for details.
ON/STANDBY button
DVD display
OPEN/CLOSE button
SKIP buttons
Remote sensor
STOP button
Disc tray
Power indicator
PLAY button
13
18
18
18
11
18
1818
20
OUTPUT
L
R
PB
PR
COAXIAL
S-VIDEO
DIGITAL AUDIO AUDIO
VIDEO
Y
COMPONENT
AC Power cord
COMPONENT VIDEO OUT (Y/P
B
/P
R
) jacks
14
16 17
14
S-VIDEO OUT jack
VIDEO OUT jack
COAXIAL DIGITAL AUDIO OUT jack
AUDIO OUT (L/R) jacks
15
14 15
2F10101A [E] P10-13 1/18/05, 6:37 PM10
11
Display
The elapsed time (hh:mm) is displayed.
During playback
Information about the unit and the disc is shown here.
There is no disc in the unit.
The disc tray is open.
Full stop
The elapsed time at track (mm:ss) is displayed.
During playback
Full stop
The total time (mm:ss) is displayed.
The unit cannot read the disc, or the disc may be damaged.
The display may vary depending on the types of discs you play.
DVD video disc Video CD/Audio CD
2F10101A [E] P10-13 1/18/05, 6:37 PM11
12
Introduction
Remote control
Identification of controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in for details.
MENU button
Use the MENU button to display the menu
included on many DVD video discs.
To operate a menu, follow the instructions
in “DVD menu”
25
.
2F10101A [E] P10-13 1/18/05, 6:37 PM12
13
Open the battery compartment cover in the
direction of the arrow.
1
Operating with the remote control
Point the remote control at the remote sensor and
press the buttons.
Distance:Approx. 7 m (23 feet) from the front of the
remote sensor
Angle: Approx. 30° in each direction of the front of
the remote sensor
* Do not expose the remote sensor of the DVD video
player to a strong light source such as direct sunlight
or other illumination. If you do so, you may not be able
to operate the DVD video player via the remote
control.
Notes on the remote control
Direct the remote control at the remote sensor of the DVD
video player.
Do not drop or give the remote control a shock.
Do not leave the remote control near an extremely hot or
humid place.
Do not spill water or put anything wet on the remote control.
Do not disassemble the remote control.
When using the remote control, press the button at intervals
of about 1 second to ensure the correct mode of operation.
2
3
Loading batteries
Within approx. 7 m (23 feet)
Install two “R03/AAA” batteries (supplied),
paying attention to the polarity diagram in the
battery compartment.
Replace the compartment cover.
Caution:
• Never throw batteries into a fire.
Notes:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
Attention should be drawn to the environmental aspects of
battery disposal.
• Do not mix different battery types or combine used batteries
with new ones.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both batteries
with new ones.
• If the batteries are dead or if you will not be using the remote
control for a long time, remove the batteries to prevent
battery acid from leaking into the battery compartment.
2F10101A [E] P10-13 1/18/05, 6:37 PM13
14
Connections
OUTPUT
L
R
P
B
P
R
COAXIAL
S-VIDEO
DIGITAL AUDIO AUDIO
VIDEO
Y
COMPONENT
Connecting to a TV
To S-VIDEO OUT
To VIDEO
OUT
To AUDIO
OUT
(red)
(white)
(yellow)
Signal flow
(red)
(white)
To video input
To S-Video input
Audio/video cable (supplied)
S-Video cable (not supplied)
To audio inputs
Notes:
Refer to the owner’s manual of the connected TV as well.
When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet
before making any connections.
If your television set has one audio input, connect the left and right audio outputs of the DVD video player to a Y cable
adapter (not supplied) and then connect to your TV.
Connect the DVD video player directly to your TV. If you connect the DVD video player to a VCR, TV/VCR combination or
video selector, the playback picture may be distorted as DVD video discs are copy protected.
TV or monitor with
audio/video inputs
To wall outlet
Connecting to a TV
Connect the DVD video player to your TV.
(yellow)
If the TV has an S-Video input,
connect the DVD video player with
an S-Video cable. When using an
S-Video cable, do not connect the
yellow video cable.
2F10101A [E] P14-17 1/27/05, 10:0214
15
Notes:
Refer to the owner’s manual of the connected equipment as well.
When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
If you place the DVD video player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the
DVD video player away from the tuner and radio.
The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.
•Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power
on, the speakers may be damaged.
Connecting to an audio system and TV equipped with component video inputs
Signal flow
OUTPUT
L
R
P
B
P
R
COAXIAL
S-VIDEO
DIGITAL AUDIO AUDIO
VIDEO
Y
COMPONENT
To P R
VIDEO
OUT
To audio inputs
of the amplifier
(red)(white)
(red)(white)
To Y
VIDEO
OUT
To P B
VIDEO
OUT
To Y video input
To PB video input
To PR video input
To AUDIO OUT
TV or monitor with
ColorStream
®
component video inputs
Audio system
Audio cable
(not supplied)
To wall outlet
Component video outputs
PROGRESSIVE outputs
Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video
signal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.
INTERLACED outputs
Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest quality
DVD picture playback.
Notes:
Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)
In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a
case, adjust the TV or monitor for optimum performance.
Component video cable (not supplied)
If the TV has the Component input,
connect the DVD video player with
the Component cable. When using
the Component cable, do not
connect the yellow video cable.
2F10101A [E] P14-17 1/27/05, 10:0215
16
Connections
*
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Connecting to an amplifier equipped with a Dolby Digital decoder
Connecting to an amplifier equipped with Dolby Surround Pro Logic
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left
front speakers, a center speaker, and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.” Refer to
that amplifier’s owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
This connection is only suitable for Video CDs and Audio CDs.
Connecting to an amplifier equipped with a DTS decoder
Digital Theater Systems (DTS)
DTS is a high quality surround technology used in theaters and now available for home use, on
DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS
encoded sound tracks on DVD video discs or audio CDs.
Manufactured under license from
Dolby Laboratories. “Dolby”, “Pro
Logic”, and the double-D symbol
are trademarks of Dolby
Laboratories.
* Connect one or two rear speakers.
The output sound from the rear
speakers will be monaural even if you
connect two rear speakers.
“DTS” and “DTS Digital Out” are
registered trademarks of Digital
Theater Systems, Inc.
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest movies, and
is now available to reproduce this realistic effect in the home. You can enjoy motion picture and
live concert DVD video discs encoded via the Dolby Digital recording system with this dynamic
realistic sound by connecting the DVD video player to a 6 channel amplifier equipped with a
Dolby Digital decoder or Dolby Digital processor. If you have a Dolby Surround Pro Logic
decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full
5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.
Connecting to optional equipment
You can enjoy high quality dynamic sounds by connecting the
unit to optional audio equipment.
For connection to your TV, see “Connecting to a TV” .
To audio input
Audio cable (not supplied)
To AUDIO OUT
Amplifier equipped with
Dolby Surround Pro Logic
75 coaxial cable (not supplied)
To COAXIAL
type digital
audio input
Amplifier equipped with a
Dolby Digital decoder
Amplifier equipped with
a DTS decoder
75 coaxial cable (not supplied)
To COAXIAL
type digital
audio input
Use DVD video discs encoded via
the Dolby Digital recording system.
• Use DVD video discs or audio CDs
encoded via the DTS recording
system.
2F10101A [E] P14-17 2/7/05, 4:52 PM16
17
Warning
When playing DTS-encoded discs (DVD video discs and audio CDs), excessive noise may be output from the analog stereo
jacks. To avoid possible damage to the audio system, you should take proper precautions when the AUDIO OUT (L/R) jacks
of the DVD video player are connected to an amplification system. (Do not leave the ANALOG AUDIO OUT (L/R) cables
dangling.) To enjoy DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must
be connected to the COAXIAL DIGITAL AUDIO OUT jack of the DVD video player.
Connecting to an amplifier equipped with an MPEG2 audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs encoded via the MPEG2 recording system with dynamic realistic
sound by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor.
Connecting to an amplifier equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and
speaker system (right and left front speakers).
Notes:
DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD video player to the AC-3 RF input of a Dolby Digital
Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL
AUDIO OUT jack of the DVD video player.
Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD video player to the “COAXIAL” input of a Receiver or
Processor.
Refer to the owner’s manual of the connected equipment as well.
When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound.
Turn off the amplifier before you connect or disconnect the DVD video player’s power cord. If you leave the amplifier power
on, the speakers may be damaged.
Amplifier equipped with an
MPEG2 audio decoder
75 coaxial cable (not supplied)
To COAXIAL
type digital
audio input
Amplifier equipped with
a digital audio input
75 coaxial cable (not supplied)
To COAXIAL
type digital
audio input
Use DVD video discs encoded
via the MPEG2 recording
system.
2F10101A [E] P14-17 1/18/05, 6:37 PM17
18
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
Basic playback
Display window
Power indicatorOPEN/CLOSE
STOPDisc tray PLAY ON/STANDBY
To start playback in the stop mode
Press PLAY.
OR
Reading
Playing a disc
This section shows you the basics on how to play a disc.
Basic playback
Preparations:
When you want to view a disc, turn on the TV and select the corresponding video input connected to the DVD. This
may include S-video or component video inputs which are exclusive to DVD playback.
When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input
connected to the DVD.
No Disc
Press ON/STANDBY.
The DVD turns on and the Power
indicator lights.
“Reading” display will change to
“No Disc”.
(If DVD disc has already loaded, play-
back will start automatically.)
Press OPEN/CLOSE.
The disc tray opens.
Place the disc on the disc tray.
With the playback
side down
There are two different disc sizes. Place the disc
in the correct guide on the disc tray. If the disc is
out of the guide, it may damage the disc and
cause the DVD to malfunction.
Do not place a disc which is unplayable in this
DVD.
Press OPEN/CLOSE or PLAY on the unit.
The disc tray closes automatically.
On the TV-screen, “
” changes to
“Reading” and then playback
commences.
A menu screen will appear on the TV screen, if
the disc has a menu feature.
Press C/D or B/A to select title, then press
ENTER. Title is selected and play commences.
Press STOP to end playback.
Resuming facility
The unit records the stopped point,
depending on the disc. “
appears on the screen. Press
PLAY to resume playback (from the
scene point).
If you press STOP again or unload
the disc (“
” appears on the
screen.), the unit will clear the
stopped point.
1
2
3
4
5
DVD
VCD
CD
2F10101A [E] P18-20 1/18/05, 6:37 PM18
19
To pause playback (still mode)
Press PAUSE/STEP during playback.
To resume normal playback, press
PLAY.
The sound is muted during still
mode.
To stop playback
Press STOP.
Notes:
If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen
according to the type of loaded disc. In this case, check your disc again (see pages 8 and 35).
Some discs may take a minute or so to start playback.
When you set a single-faced disc label downwards (i.e. the wrong way up) and press OPEN/CLOSE or PLAY on the unit,
“Reading” will appear on the display for a few minutes and then “Incorrect Disc” will continue to be displayed.
Some discs may not work the resuming facility.
Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see page 27.
Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according
to the disc contents the software producers designed, some playback features may not be available. Also refer to the
instructions supplied with the DVDs.
Do not move the unit during playback. Doing so may damage the disc.
Use the OPEN/CLOSE to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may cause the
unit to malfunction.
Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the unit to
malfunction.
In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press
POWER (I / ) on your remote control once the movie is completed.
There may be a slight delay between you pressing the button and the function activating.
To obtain a higher quality picture
Occasionally, some picture noise not usually visible during a normal broadcast
may appear on the TV screen while playing a DVD video disc because the high
resolution pictures on these discs include a lot of information. While the amount of
noise depends on the TV you use with this unit, you should generally reduce the
sharpness adjustment on your TV when viewing DVD video discs.
About
DVD VCD CD
The
DVD VCD CD
icons on the heading bar show the playable discs for the
function described under that heading.
DVD
: You can use this function with DVD video discs.
VCD
: You can use this function with Video CDs.
CD
: You can use this function with Audio CDs and CD-R/RW CDs.
STOP
Screen saver function
The screen saver operates when you leave the unit in
DVD stop mode for approx. five minutes.
The screen will repeatedly get dark gradually and back
to normal.
OPEN/CLOSE
STOP
PAUSE/STEP
PLAY
To remove the disc
Press OPEN/CLOSE.
Remove the disc after the disc tray
opens completely.
Be sure to press OPEN/CLOSE to close the disc tray
after you remove the disc.
POWER
ENTER
C/D/B/A
2F10101A [E] P18-20 1/18/05, 6:37 PM19
20
Playing a disc (continued)
You can play discs at various speeds.
Playing frame by frame
Basic playback
DVD
VCD
DVD
VCD
Playing in fast reverse or fast forward directions
Press REW or FF during playback.
REW: Fast reverse playback
FF: Fast forward playback
Each time you press REW or FF, the
playback speed changes.
To resume normal playback
Press PLAY.
Notes:
The DVD video player mutes sound and subtitles during
reverse and forward scan of DVD/VCD video discs.
However, this unit plays sound during fast forward or fast
reverse play of audio CDs.
The playback speed may differ depending on the disc.
Press PAUSE/STEP during still playback.
Each time you press PAUSE/STEP,
the picture advances one frame.
To resume normal playback
Press PLAY.
Note:
The sound is muted during frame by frame playback.
Press SLOW ( ) Forward or SLOW ( ) Reverse
during playback.
Each time you press the button, the
slow-motion speed changes.
To resume normal playback
Press PLAY.
Notes:
The sound is muted during slow-motion playback.
The Video CD cannot play Reverse Slow.
Press SKIP or repeatedly to display the chapter or track number you want.
Playback starts from the selected chapter or track.
To locate succeeding chapters or
tracks.
Playback starts from the beginning of the
current chapter or track.
When you press twice in quick successions,
playback starts from the beginning of the
preceding chapter or track.
A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature you tried is not
available on the disc, or the DVD cannot access the feature at this time. This does not indicate a problem with the DVD.
The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leave
the still video image or On screen display image displayed on your TV for an extended period of time, you risk permanent
damage to your television screen. Projection televisions are very susceptible.
Notes:
Locating a chapter or track
Playing in slow-motion
DVD
VCD
CD
DVD
VCD
CD
FF
REW
PLAY
PAUSE/STEP
SKIP /
SLOW /
2F10101A [E] P18-20 1/18/05, 6:37 PM20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Toshiba SD-K750SU User manual

Category
DVD players
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI