LG 43LU660H Installation guide

Type
Installation guide
INSTALLATION MANUAL
LED TV*
* LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and
retain it for future reference.
LU660H-S*
www.lg.com
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
ENG
ENGLISH
2
TABLE OF CONTENTS
3 LOCATION AND FUNCTION OF
CONTROLS
3 Parts and Button
3 - Basic functions
3 - Adjusting the Menu
4 EZMANAGER
4 Introduction
4 Ez-Manager Wizard
5 - Automatically for Setup
9 - Manually for Setup
12 - USB LG Smart Install Utility
13 INSTALLATION MENU
13 Introduction
14 PUBLIC DISPLAY SETTINGS
14 Public Display Settings Operation
15 Power On Status
15 Volume (0 ≤ Min ≤ Start ≤ Max ≤ 100)
15 - Start Volume
15 - Maximum Volume
15 - Minimum Volume
16 Key Management
16 - IR Operation
16 - Local Key Operation
16 Limited Mode
16 - Setup Menu
16 - Channel Change
17 - Menu Display
17 - OSD Display
17 - System Provider Mode
17 DTV Channel Update
18 Power On Default
18 - Input
18 - Channel
18 - A/V Setting
18 - Aspect Ratio
18 Aux Source Setting
18 Power Management
18 Factory Reset
19 NETWORK
19 MAC Address
19 Network Setting
20 LG Connect
20 IP Stream Control
20 Wake On LAN
21 PRO:CENTRIC
21 Mode
21 Update Event
22 Media Type
22 Room Number Setting
23 GENERAL
23 Configuration Setup
24 External Speaker
24 Set ID Setup
25 Power Saving
25 HCEC Setup
26 Clock Setup
26 Password Change
27 Preloaded App
27 Lock Mode
27 MEDIA SHARE
27 SmartShare
27 Screen Share
28 Media Renderer
28 DIAL
28 TV Name
28 SoftAP
29 TV MANAGER
29 USB Download Menu
35 Diagnostics
36 KEY CODES
37 EXTERNAL CONTROL DEVICE
SETUP
37 RS-232C Setup
37 USB to Serial converter with USB Cable
37 RS-232C with RS-232C Cable
38 Set ID
39 Communication Parameters
39 Command reference list
40 TRANSMISSION / RECEIVING
PROTOCOL
ENGLISH
3
LOCATION AND FUNCTION OF CONTROLS
Parts and Button
Basic functions
Power On (Press)
Power Off
1
(Press and Hold)
Menu control (Press
2
)
Menu selection (Press and Hold
3
)
1 All running apps will close.
2 You can access and adjust the menu by
pressing the button when TV is on.
3 You can use the function when you access
menu control.
Adjusting the Menu
When the TV is turned on, press the button
one time. You can adjust the Menu items
using the button.
Turns the power off.
Changes the input source.
Scrolls through the saved channels.
Adjusts the volume level.
ENG
ENGLISH
4
EZMANAGER
* Image shown may differ from your TV.
Introduction
The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions. The
default Domain ‘procentric.local’ and IP Server Address are needed to be registered in DNS TV will
contact the IP Server using the default Domain ‘procentric.local’ via IP on server search page. If TV
doesn’t contact the Server, TV will search the pre-defined channel earlier than all channels.
Ez-Manager Wizard
If you are using Pro:Centric, this setup wizard till help you easily set up the TV. Select NEXT to
continue.
Otherwise, if you will not be installing a Pro:Centric Server, select X to quit.
ENGLISH
5
Automatically for Setup
1 From the TV Configuration Options screen, you can choose how to proceed with the
configuration of this TV. Whether you will configure the TV for Pro:Centric operation via the
wizard or use a USB memory device to configure the TV, you may first wish to set the Room
Number on the TV.
If you intend to set Room Number as part of the TV configuration, use the Room Number
option to assign the Room # for this TV before you continue with additional configuration.
In the Label field, use the Left/Right arrow keys to specify a North, South, East, or West
designation for this TV.
In the Room Number field, you can use the number keys on the Installer Remote to direct enter
a room number or use the virtual keyboard on the TV screen.
To continue, move and select NEXT.
ENG
ENGLISH
6
If you intend to set network, use the Network Settings option. You can connect easily to wired/
wireless network by this option. (page. 19)
ENGLISH
7
2 This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data
channel, select the NEXT.
ENG
ENGLISH
8
3 Downloading the Pro:Centric application files takes few minutes.
4 After the installation is completed, the following screen will be displayed.
ENGLISH
9
Manually for Setup
1 Select a Label and/or enter the Room Number using the numeric keypad on the remotes or
using the virtual keyboard on the TV screen. To continue, move and select NEXT.
2 Please select the MANUAL PRO:CENTRIC.
ENG
ENGLISH
10
3 Configure the appropriate Pro:Centric settings in the TV.
ENGLISH
11
4 Downloading the Pro:Centric application files takes few minutes.
5 After the installation is completed, the following screen will be displayed.
ENG
ENGLISH
12
USB LG Smart Install Utility
1 Select the USB CONFIGURATION > TV MANAGER.
- If you have USB Memory for ‘LG_DTV or ‘lg_dtv’ folder, this step shows the USB file list for
downloading the items.
2 Downloading the files takes few minutes.
ENGLISH
13
3 After the installation is completed, the following screen will be displayed.
INSTALLATION MENU
Introduction
The abundant functions for Hotel TV linked with software installation can be projected on OSD as
Public Display Settings.
The wide range of hotel features can be performed simply on additional window to enhance the LG
hotel TVs easy installation and convenient operation for Hotelier and System Integrators.
* Image shown may differ from your TV.
TV
1 Press the (Settings) button for more than 5 seconds using the user remote control, channel
information will appear at top left on the screen.
2 Enter a four digit password and press OK button. The TV is set with the initial password “1-1-0-5”.
3 Use the button to select the desired menu.
ENG
ENGLISH
14
PUBLIC DISPLAY SETTINGS
* Image shown may differ from your TV.
1 Use the button to select the Public Display Settings.
2 Use the OK button and then button to select Public Display Mode.
- When Public Display Mode is set to ON (Work), all functions of Public Display Mode apply.
Public Display Settings Operation
Decide to work all functions of Public Display Settings or not by setting Public Display Settings
as ON (Work) or OFF (Do Not Work)
When Public Display Settings is set to ON (Work), all functions of Public Display apply.
When Public Display Settings is set to OFF (Do Not Work), all functions of Public Display don’t
apply.
When it is set to ON, Key Lock item of the User menu is disabled and the OSD is displayed same to
the Local Key Operation setting of the Public Display Mode.
When it is set to ON, all items reserved at the Schedule list are deleted and the reservation
function is not supported. (Applied for the model offering the reservation function)
The TV triggered by the external device (ex: SIMPLINK, TV Link-Tuner, etc.) operates separately
from the Public Display Settings.
When it is set to ON, User Menu > General > Reset to Initial Settings is disabled.
When Public Display Settings is set to ON (Work), all skipped programs are not tuned by number
keys.
When Public Display Settings is set to ON (Work), Detailed Information about the Channel is not
available in the EPG.
ENGLISH
15
Power On Status
Decide to select working status of TV Set when turn on main power.
You can set with PWR, STD, LST.
PWR always make TV set On status when turn on main power .
STD make Stand-by status when turn on main power.
LST make TVSet work like previous power status. As same concept as Power Backup mode; If main
power were turned off in Power On status, TVSet would work in On status. If main power were
turned off in Stand-by status, TVSet would work in Stand-by status.
If there Block All is both IR Operation and Local Key Operation from Key Management, In order
to provide the option that must be able to turn on the TV in the TV turned off situation, change
the value of the PWR. (Reference the Key Management)
Volume (0 ≤ Min ≤ Start ≤ Max ≤ 100)
Decide to apply volume policy of Start Volume, Maximum Volume and Minimum Volume
as On (Work) or Off (Do Not Work).
Start Volume
This entry sets the start volume level when is power on.
The level is specified as a number between minimum volume to maximum value.
(Min ≤ Start ≤ Max)
The default setting is Off (disabled).
When enabled, if the value is lower then the minimum specified in the minimum
volume entry, the minimum volume entry must be used.
When enabled, if the value is larger then the maximum specified in the maximum
volume entry, the maximum volume value must be used.
Access to a volume in Timer Power On of User Menu must be fixed to start volume
when HTNG HotelMode (Enable) and Start Volume (Off, 0 ~ 100) were set
simultaneously.
Maximum Volume
This entry sets the Maximum Volume level the set.
The level is specified as a number between Minimum Volume to 100. (Min ≤ Max ≤
100)
If the command volume up to higher than maximum volume is received, that should be
ignored.
The default value is 100.
Minimum Volume
This entry sets the Minimum Volume level the set will produce.
The level is specified as a number between 0 to Maximum Volume. (0 ≤ Min ≤ Max)
If the command volume down to lower than minimum volume is received, that should
be ignored.
The default value is 0.
ENG
ENGLISH
16
Key Management
Manage key usability of Local(Front) Key and Remote Control. When selected to On, following IR
Operation and Local Key Operation will be worked by below.
IR Operation
Decide whether work the LG remote control or not.
When IR Operation is set to Normal, all remote keys are available.
Use PWR Only makes block all remote keys except power key.
When IR Operation is set to Block All, all normal remote keys don’t work.
Local Key Operation
Decide to operate Local/Front Key working behavior by setting Local Key Operation as
Normal, Use PWR Only, Block All
When Local Key Operation is set to Normal, all local key are available.
Use PWR Only makes block all local keys except power key.
When Local Key Operation is set to Block All, all local keys don’t work.
Limited Mode
Configure TV function’s limitation. When selected to On, following sub-menus will be worked by
below.
Setup Menu
Permit to tune and manage Channels as On (Permitted) or Off (Not permitted).
Channel Change
Decide to change channel or not by setting Channel Change as On (Change Possible) or
Off (Change Impossible) when present source is TV.
When Channel Change is set to Off (Change Impossible)
- Channel Key, Numeral Key, List Key, Flash back Key don’t work and entering channel
Menu in the Main Menu OSD is impossible.
- Channel item in Timer Power On of User menu will be fixed.
- Entering Channels of User Menu is impossible regardless of Channels item of User
Menu.
When Channel Change is set to On (Change Possible), Channel Key, Numeric Key, List
Key, Q.View Key, TV/RAD Key does work and entering Channel Menu in the Main Menu
OSD is possible.
ENGLISH
17
Menu Display
Function to decide whether work with menu (including relevant menus too) of control
key (On – Enter possible) or not (Off – Enter Impossible).
Although select Off (Enter impossible), the action that press a Menu button for 5
seconds to enter installation menu is available.
When select On (Enter possible), Menu works.
OSD Display
Decide to display OSD or not by setting OSD Display as On (Display) or Off (Do not
Display).
When OSD Display is set to Off (Do not Display), all OSD is not displayed except some
exception.
Although select Off (Do not Display), the action that press a menu button for 5 seconds
to enter installation menu and entering service menu are available. (In-Start, Power-
Only, Adjust, Installation Menu …)
System Provider Mode
System Provider Mode allows access to the menu system from the front panel or remote
control but access is controlled as follows:
When value is On, Accessible Items on the menu system, others are not permissible.
- Input select screens
- Sleep Timer
- Aspect Ratio
- Closed Caption
- Safety / My Media / Network / About This TV
If the channel map is empty, Auto-tuning guide dialog should be blocked by pressing
List, Fav, CH+ (Page up), CH- (Page down) keys.
DTV Channel Update
It is a mode to set whether to update DTV channel information automatically or not.
When DTV Channel Update is set to Auto, the function to update TVs channel map according to
DTV channel’s stream information
DTV Channel Update is set to Manual, the function to keep TVs channel map even though DTV
channel’s information is changed.
ENG
ENGLISH
18
Power On Default
Set the channel to display and Volume Level, etc. when turn on power in AC Power On or Stand-by
status.
Set to On (Work) or Off (Do Not Work).
When Power On Default is set to Off, it is not applied to the subordinate Input, Channel, A/V
Setting, Aspect Ratio menu.
When Power On Default is set to On, it can set by entering the subordinate menu.
Input
Set whether it is turned on by the set input source or by the last stored input source.
Channel
Select start channel number if Input sources value is TV.
A/V Setting
If A/V Setting is changed from Off to On, A/V parameters that are set before entering
installation menu are applied whenever turn on power.
Aspect Ratio
The aspect ratio determines the default aspect ratio that the set returns to on power up.
Aux Source Setting
The Auxiliary (Input) Source Setting feature will enable or disable for each external input.
Set to On (Work) or Off (Do Not Work).
User cannot disable the current input’s Aux Source Setting.
Power Management
The Power Management feature will turn off the television receiver if no input control command is
received from either the Local or IR Key within a selected hours.
Activity on either of these inputs shall restart the Power Management timer and check key time
interval again.
This entry can be set to a value which is corresponding to the desired hours (1 to 7).
Default value is Off (disabled).
Factory Reset
Change all settings to their default values.
ENGLISH
19
NETWORK
1 Use the button to select the Network.
MAC Address
Displays the MAC address. (Not customizable).
Network Setting
One-click network connection
Connects easily to a wired/wireless network.
Network Connection to connect to an available network automatically. Follow the prompts on the
TV.
To connect to a network through Set Expert
For use in special circumstances such as in offices (in cases where a static IP is used).
1 Select a network connection, either Wired or Wireless.
2 When connecting via Wired, Configures the IP settings of the TV set. You can set the IP address,
subnet mask, gateway and DNS server.
3 When connecting via Wi-Fi, use the one of the following network connection methods.
AP List Connects to the network selected from the AP List.
Enter the SSID Connects to the wireless AP typed in.
WPS-PBC Connects easily when the button of a wireless AP supporting PBC is pressed.
WPS-PIN Connects easily when the PIN of the wireless AP that you wish to connect to
is entered in to the AP website.
Advanced Wi-Fi
Settings
After connects Wi-Fi, you can set the IP address, subnet mask, gateway and
DNS server.
ENG
ENGLISH
20
LG Connect
* Depending upon model
Sets the LG Connect function to on or off.
You can connect TV via LG TV Plus app in smart device.
Default setting is On.
IP Stream Control
Audio PTS Offset
- Controlling output stream timing of audio.
- You can set the ‘-500 ~ 500’ (Change step is -10 or +10)
Video PTS Offset
- Controlling output stream timing of audio.
- You can set the ‘-500 ~ 500’ (Change step is -10 or +10)
IGMP
- You can set IGMP version. (2 or 3)
Wake On LAN
Sets the Wake On LAN function to Enable or Disable.
The Wake On LAN feature enables the TV to receive software updates and/or be powered On
upon receipt of Wake Up Frame packets and/or Magic Packet data via the wired LAN. To facilitate
use of this feature, note that the appropriate wired connection must be made. (Wake up Frame
depends upon model)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47

LG 43LU660H Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI