Bercomac BER53PT User manual

Brand: Bercomac

Model: BER53PT

Category: Snow throwers

Type: User manual

This manual is also suitable for

BER3PTSB56H

READ&FOLLOWALLSAFETYRULES&INSTRUCTIONSBEFORE

OPERATINGYOUREQUIPMENT

106746_EN N

*ASSEMBLY *REPAIRPARTS

*OPERATION *MAINTENANCE

*106746*

BER563PT

LIMITED WARRANTY

Conditions and Products Covered:

BERCOMAC guarantees any part of the product or accessory

manufactured by BERCOMAC and found in the reasonable

judgment of BERCOMAC to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard ground

freight services are covered. This warranty applies to the

products bought and used in North America.

Warranty Period

(from date of the original retail purchase)

Residential, light commercial or regular commercial

(agricultural) use: 1 year

Commercial intense, industrial or rental use: 90 days

Exceptions Noted Below; the following items have a different

coverage conditions and limited time:

Tire Chains:

o90 days residential or light commercial use

oNo warranty on other application

Engines: Will vary as per the manufacturer

Please refer to the engine manufacturer’s warranty

statement included with the unit. BERCOMAC is not

authorized to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

Pick-up or delivery charges or in-home services fees.

Any damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

Cost of regular use or maintenance service or parts, such as

gas, oil, lubricants, tune-up parts, and adjustments.

Any part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

withtheinstructionsintheowner’smanual.

Repair due to normal wear and or any wear items such as

shear pins, bolts, belts, winch cable, cutting edge, skid

shoes, etc.

Expedited freight fee services for replacement parts.

Shear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage are

not covered.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’sResponsibilities:

BERCOMAC’s defective equipment or part must be returned

to an authorized dealer within the warranty period for repairs.

In the event that defective merchandise must be returned to

manufacturer for repairs, freight fees are prepaid and a written

authorization from BERCOMAC must be obtained by dealer

prior to the shipment. This warranty extends only to

equipment operated under normal conditions. To validate a

warranty claim, it is the user’s responsibility to maintain and

servicetheunitasspecifiedintheowner’smanualortohave

the unit serviced at their dealer at their expense.

General Conditions:

The sole liability of BERCOMAC with respect to this warranty

shall be strictly and exclusively repair and replacement as

mentioned herein. BERCOMAC shall not have any liability for

any other costs, loss or damage, including but not limited to,

any incidental or consequential loss or damage.

Taking advantage of the warranty does not in any way extend

the length or renewal of the warranty.

In particular, without being limited to, BERCOMAC shall have

no liability or responsibility for:

Travel time, overtime, after hours time or other

extraordinary repair charges or relating to repairs and or

replacements outside of normal business hours.

Rental of like or similar replacement equipment during the

period of any, repair or replacement work.

Any communicating or travel charges.

Loss or damage to person or property other than that

covered by the terms of this warranty.

Any claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

Attorney’s fees.

BERCOMAC’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge up

to our maximum labor rates and pre-established times and no

claim of breach of warranty shall be cause for cancellation or

rescission of the contract of sale of any product or accessory.

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services: Contact the Mahindra dealer where equipment was purchased or any other Mahindra

service dealer to arrange service at their dealership. To locate a dealer convenient to you, access our website at

www.mahindrausa.com. Don't forget to bring your proof of purchase (sales receipt) to the Mahindra dealer.

Revised 11-23-2012

TABLEOFCONTENTS

INTRODUCTION

...............................................................................................................................................

SAFETYPRECAUTIONS

..................................................................................................................................

SAFETYDECALS

..............................................................................................................................................

ASSEMBLY

Step1 SnowblowerPreparation

.........................................................................................................

Step2: PTOdriveshaftPreparationandinstallation

............................................................................

Step3: SnowblowerInstallation

...........................................................................................................

Step4: Snowblowerandtractoradjustments

......................................................................................

OPERATION

SnowblowerOperation

.........................................................................................................................

Controls

................................................................................................................................................

SnowRemoval

.....................................................................................................................................

MAINTENANCE

Adjustments

..........................................................................................................................................

Lubrication

............................................................................................................................................

ShearBoltReplacement

.......................................................................................................................

BeltReplacement

.................................................................................................................................

PulleyReplacement

...............................................................................................................................

DISMOUNTING&STORAGE

...........................................................................................................................

TROUBLESHOOTING

.......................................................................................................................................

PARTSBREAKDOWNANDPARTSLIST

56’’Snowblower

.....................................................................................................................................

TORQUESPECIFICATIONTABLE

..................................................................................................................

OPTIONS&ATTACHMENTS

...........................................................................................................................

PAGE

iii

INTRODUCTION

TO THE PURCHASER

This new accessory was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to

use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will

use this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS

MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.

DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF

HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions

are not followed.

WARNING:

Signals a hazard that may cause serious injury or death if the recommended precautions are

not followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are

not followed.

Record your attachment serial number and purchase date in the section reserved below (there is no serial number on

the subframe). Your dealer requires this information to give you prompt, effi

cient service when ordering replacement

parts. Use only genuine parts when replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

(IF APPLICABLE)

MODEL NUMBER: ___________________________

PURCHASE DATE : ___________________________

OPERATION:

1. Do not put hands or feet near, under or inside rotating

parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine (motor),

disconnect the wire from the spark plug(s) and keep

wire away to prevent accidental starting. Thoroughly

inspect the accessory for any damage and repair

damage before restarting and using the accessory.

4. If the unit should start to vibrate abnormally, stop the

engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the ignition key.

6. Do not run the engine indoors, except when starting

the engine and for transporting in or out of the

building. Do not operate or let motor run in a storage

area without ventilation because gas contains

carbon monoxide which is odorless, colorless and

can cause death.

7. Never use the accessories across the face of

slopes, go from top to bottom. Exercise extreme

caution when using equipment on slopes. Do not

attempt to clear a steep slope.

8. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

9. Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

10. Do not carry passengers.

11. Disengage power to the accessory when it is

transported or not in use.

12. Never operate the accessory without good visibility

or light.

13. Keep the accessory away from heat sources or

flames.

14. If applicable, never handle the winch cable or hook

while in tension.

MAINTENANCE AND STORAGE

1. When cleaning, repairing or inspecting the vehicle

and accessory: stop the engine, set brake, remove

ignition key, and wait that all moving parts have

stopped. For gasoline engine, disconnect wire from

the spark plug(s) and keep wire away to prevent

accidental starting.

2. Check all the bolts and components at frequent

intervals to make sure that they are properly

tightened.

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources are

present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Alwaysrefertotheowner’smanualwhenyoustore

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6 For winter accessories, (if applicable), let the engine

run for a few minutes after clearing snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter (if

applicable) every day. Clean it or replace it as

necessary. Change the oil more often when working

in dusty conditions. See the vehicle’s and

accessory'sowner’smanual.

TRANSPORT

1. Review Transport Safety instructions in vehicle

manual before moving.

2. Check with local authorities regarding transport on

public roads. Obey all applicable laws and

regulations.

3. Make sure all lights and reflectors that are required

by the local highway and transport authorities

(exemple : SMV (Slow Moving Vehicle)) are in

place, are clean, and can be seen clearly by all

overtaking and oncoming traffic.

4. Never have the equipment in operation during

transport.

5. Always travel at a safe speed.

SAFETY PRECAUTIONS

SAFETYDECALS

REPLACEIFDECALSAREDAMAGED

SEEPARTSBREAKDOWNFORDECALLOCATION

Symbol Description

Decal#105126

Toavoidseriousinjury:

Keephands,feet&clothingawayfromrotatingaugerwhilethevehicle’s

engineisrunning.

Decal#105127

Toavoidseriousinjury:

Keephandsoutofthisdischargechutewhilethevehicle’sengineis

running.

Decal#105852

Toavoidseriousinjury:

Keeppeopleandclothingaway.

Donotoperatewithoutalldriveline,tractorandequipmentshieldsinplace,

norwithoutthedrivelinessecurelyattachedatbothends.

Decal#105130

Beforeinstallingorusing:

Locate,readandmakesuretounderstandalloftheowner’smanual.

Decal#105131

Refertoowner’smanualaboutwearingsafetyglasses,earmuffsand

mask.

Refertoowner’smanualforuseofcounterweights,cattracksandtire

chains.

ASSEMBLY

ASSEMBLYINSTRUCTIONS

IMPORTANT:UNLESSOTHERWISESPECIFIEDTORQUEALLBOLTSACCORDINGTOTORQUESPECI-

FICATIONTABLE(SEETABLEOFCONTENTS)WHENSTATED:TIGHTENFIRMLY.REFERTOPARTS

BREAKDOWNSECTIONFORPARTIDENTIFICATION.

TOOLSREQUIRED

Ratchet

Sockets:3/4’’,15/16’’,1/2’’,7/16’’

Wrench:3/4’’,15/16’’,1/2’’,7/16’’

Allenkey

NOTE:Inthismanual,therightandleftsideisdeterminedbeingattherearofthesnowblower

Overallview

Removethesnowblowerfromtheshippingcrate.

Removethesupportplatesfromtheskidshoes.

Removetheothercomponentsfromthecrate.

ASSEMBLY

STEP1

SNOWBLOWERPREPARATION:

Refertopartsbreakdownsectionforpartsidentification.

Chuteinstallation

Installthemetalrotationring(item1)overthe

openingofthechuteasshown.Thisrotatingringis

providedinyourrotationkit(electricorhydraulic)

Installthenylonrotationring(item2)overthe

openingofthechuteasshown.

Placethechute(item3)facingtherearofbloweron

theopeningasshown.

Clipthebackundertherotationringandturnthe

chutetowardsthefronttolockintoplace.

Thenfinalisetheinstallationofthechuterotationand/

ordeflectionkit

Rearhitchinstallation

Installthelink(item1)withtherightleverarm(item2)

andtheleftleverarm(item3)withabolt5/8’’x3

1/2’’(item4)andanyloninsertlocknut5/8.

Installthisassemblyonthesnowblowerwith2bolts

1/2’’x3

3/4’’(item5)andnut1/2’’.Then,installthe

link(item4)with2bolts1/2’’x1

1/2’’(item6)and2

nyloninsertlocknut1/2’’.

Installthesleeve(item7)withabolt5/8’’x3

1/2’’(item8)andanyloninsertlocknut5/8’’

Finally,putinplacethepinwithhairpin(item9)

Note:Thissnowblowercanbeinstalledonatractorwithastandard3pointhitchcategory1andonatractor

equippedwitha3pointsquickhitchcategory1.Toinstallwiththequickhitchthesleeve(item10)mustbein

place.Forastandard3pointshitch,thesleevemustberemoved.

NOTE:Wheninstallingthechuterotationkit:make

surethechuteisrotatinginthedirectionofthefront

ofthesnowblowernotinthedirectionofthetractor.If

thechuteisrotationinthedirectionofthetractorflip

therotatingring.(item1)

ASSEMBLY

STEP2

PTODRIVESHAFTPREPARATIONANDINSTALLATION

Refertopartsbreakdownsectionforpartsidentification.

PTOdriveshaftlengthadjustment

Ifneeded,removethelengthCfromthePTOshaft

TocutthePTOdriveshaft:

a. RemovethePTOguards.

b. Cutthemaleandfemalepartofthedriveshaftof

thesamelength(distanceC)thendeburrthe

endofthedrivesshaftthatwerecut

c. Cutthe2PTOguardsofthesamelength

d. Greaseallmetallicpart

e. Reinstalltheguards

Minimumoverlap

ThelengthofthePTOdriveshamustbeadjustedinregardstothelengthofthearmsofthetractorortheopons

PTOdriveshaftlengthrequired

Installthesnowbloweronyourtractor

Thelengthofthedriveshaftmustbe:

Maximum:Makesuretheshaftisnotbottoming

withinallmovementrangeoftheaccessory/3points

hitch.

Minimum:Ithastobelongenoughtomakesurethat

withinallmovementrangeoftheaccessorythatthe

ptodriveshafthasaminimumoverlapof4inches.

Seenextsectionifyouneedtoadjustthelengthof

thePTOshaft

NOTE:istheowner’s/user’sresponsibilitytomake

suretheinstallationmeetstheserequirements.

WARNING

TOPREVENTINJURIES:

Never leave the driver seat without disengaging

the snowblower, stopping the engine, applying

theparkingbrakesandremovingtheignitionkey.

ASSEMBLY

Skidshoeadjustment:

LEVELPAVEDSURFACE:Adjustskidshoestoallow

3/16" to 1/4"or 5mmto 7mm clearance (A)between

cuttingedgeandsurface.

UNEVENORGRAVELSURFACE:Adjustskidshoes

toallow1/2"to5/8"or13mmto16mmclearance(A)

betweencuttingedgeandsurface.

PTOdriveshaftinstallation

Note:puttingthesnowblowerfacedownwillhelpfor

thisinstallation

Installthekey(item1)onthesnowblowerinputshaft

(item2).

InstallthePTOdriveshaft(item3)onthesnowblower

inputshaft.Theninstallabolt1/4’’x2

1/2’’(item4)and

anyloninsertlocknut1/4’’(item5).

Finalizetheinstallationbytighteningthesetscrew(item

PTOdriveshaftchaininstallation

InstallthePTOdriveshaftchain(item7)onthe

snowblowerhole(item8)

STEP3

INSTALLTHESNOWBLOWERONTHETRACTOR

Refertopartsbreakdownsectionforpartsidentification.

STEP4

TRACTORANDSNOWBLOWERADJUSTMENT

Refertopartsbreakdownsectionforpartsidentification.

Remove theparking stand after installing on the

tractor3pointshitch.:

Removethelockpin(item1)thentheparkingstand

(item2)mustbepivotedandlockedinplacewiththe

lockpin

InstallthePTOdriveshaftontheinputshaftofthe

tractor

CAUTION

Theliftspanofthe3pointhitchmustbeadjustedtoensurethePTOdriveshaftwillnotbedamaged:

Adjustthelowerandhigherstopperlocationonthe3pointshitchliftingleveronthetractor.Theliftingstopper

mustbeadjustedtoensurethePTOdriveshaftangleisnotmorethan35degrees

InadditionthePTOtractoroutputshaftandthesnowblowerinputshaftmustbeparallel.Ifthisisnotthecase,

youmustadjustthetoplinkofthe3pointquickhitch.

OPERATION

NOTE:Toincreasethelifespanofthecomponents,

alwaysdisengagethesnowblowerwhenitisraisedat

toplevel.

SNOWBLOWEROPERATION

IMPORTANT:

Always inspect the hydraulic components and hoses

before using. Replace any damaged or worn parts

immediately.Ifyoususpectahoseleak,DONOTuse

your hand to locate it. Use a piece of cardboard or

wood.

a) Makesurethesnowblowerisclearofsnowbefore

engagingthesnowblower.

b) Make sure that the auger and impeller operate

freely.

c) Startthetractorengine.

d) Before engaging the snowblower drive, always

havetheenginerunningatmediumR.P.M.

Operate the snowblower at maximum engine

R.P.M when removing wet or sticky snow. A low

R.P.M.willtendtoplugthechute.

f) Alwaysmakesurethatthehydraulichosesnever

comeintocontactwiththemobileelementson

thevehicle.

g) Alwaysmakesurethattheelectricwiresnever

comeintocontactwiththemobileelementson

thevehicle.

CONTROLS

CHUTEROTATION

Usethetractor’shydrauliccontroltoturnthechutefrom

one side to the other with the hydraulic chute rotation

option.Forelectricoption,usetheelectriccontrolofthe

kit. If the chute does not turn in the desired direction,

reviewtherotationkitinstallation.

CHUTEDEFLECTOR

Settheangleofthedeflectoraccordingtothedistance

the snow must be thrown and to prevent property

damage.Tochangethedeflectorangle,loosenthetwo

deflectorknobs&adjustthedeflectortotheappropriate

angleandretightenthetwoknobssecurely.

SNOWREMOVAL

Whenremovingsnow,donotusethesnowbloweras

a dozer blade to push snow. Allow snowblower to

ingest snow at its own speed. If the speed of your

tractor is too fast, the snowblower may become

overloaded and plug. For best results, raise the

snowblower and remove a top layer of snow. A

second pass with the snowblower will remove the

remainingsnow.

WARNING

Read the tractor Owner’s Manual carefully. Be

thoroughly familiar with the controls & proper

use of the attachment. Know how to stop the

attachment&disengagethecontrolsquickly

WARNING

TOPREVENTINJURIES:

Never leave the driver seat without disengaging

the snowblower, stopping the engine, applying

theparkingbrakesandremovingtheignitionkey.

Neveroperateonslopesofmorethan10%.

WARNING

Handcontactwiththerotatingimpellerinsidethe

discharge chute is the most common cause of

injury associated with snowblowers. Never use

yourhandtocleanoutthedischargechute.

Do not attempt to clear plugged chute, auger or

fanofsnowwhilethetractorsengineisrunning.

Disengagesnowblower.

Lower snowblower to the ground and set

parkingbrake.

SHUTTHEENGINEOFF&REMOVEKEY!

Wait10secondstobesurethatallmovingparts

such as the impeller blades have stopped

moving.

Always use the clean

out tool (chute shovel)

supplied with this snowblower, NOT YOUR

HANDS

WARNING

 AlwayschecktoseethatbothendsofthePTO

shaft are securely attached every time the

snowblowerisused.

 This should always be done with the tractor

engineoff

 Do not run the snowblower without the PTO

shieldinplace

 Operate only with ROPS and seatbelt

equippedtractors

 Neveroperateover540PTOrpmspeed

MAINTENANCE

ADJUSTMENTS

Skidshoeadjustment:

.LEVEL PAVED SURFACE: Adjust skid shoes to

allow 3/16" to 1/4" or 5mm to 7mm clearance

betweencuttingedgeandsurface.

UNEVENORGRAVELSURFACE:Adjustskidshoes

to allow 1/2" to 5/8" or 13mm to 16mm clearance

betweencuttingedgeandsurface.

CUTTINGEDGEMAINTENANCE

Verify from time to time the wearing on the cutting

edge to make sure you do not wear out the base of

the snowblower’s chassis. This cutting edge is

reversible.

WARNING

TOPREVENTINJURIES:

Stopthesnowblowermotor.

Applyparkingbrake.

Removetheignitionkey.

AUGERS, FAN AND DRIVESHAFT SHEAR

BOLTREPLACEMENT

Shear bolts are to be considered a preventive

measure and not an assured protection. Operator

vigilanceisrequired.Thoroughlyinspect the areas

wherethesnowbloweristobeusedandremoveall

foreignobjects.

Toavoiddamagetothesnowblower:

Useonlytheoriginalshearbolts(groovedbolts).

#104000inbagsof10fortheaugers.

#105627inbagsof10forthefan.

Refertopartsbreakdownforthedriveshaft

The use of any other shear bolt will not insure any

protectionandmayvoidthewarranty.

IMPORTANT:ITISVERYIMPORTANTTOREPLACE

THEAUGERSINTHESAMEPOSITIONASSHOWN

IN THE DRAWING BEFORE INSTALLING THE

SHEARBOLTS.

MAINTENANCE

a) Check mounting bolts at frequent intervals for

proper tightness in order to prevent costly repairs.

Make sure your snowblower is in safe working

condition.

b) Provide adequate blocking before working under

thesnowblowerwheninraisedposition.

LUBRICATION

Applyoilatallpivotpoints.

Chute Rotation System: Oil chute base every sixteen

hoursofoperation.

Gearbox:

Checktheoilannually.Ifnecessary,addAGMA5EPor

SAE90oil.

Thegearboxshouldhaveatotalof275mlofoilorfilled

totherimoftheboltholewheninstalledonthe

snowblower.(seefigure).

PTOdriveshaftandgreasablebearings:

Greaseateach8hourofuse

GearBox

MAINTENANCE

BELTREPLACEMENT:

1) Turnsnowblowerfacedown.

2) Remove the half driveline (See snowblower

assemblysection).

3) Remove the driveline guard (item 1) by removing

the four 5/16’’ x 3/4’’ hex bolts (item 2), four lock

washers(item3)andfourflatwashers(item4).

4) Loosen the four 5/16’’ x 4 1/2’’ bolts (item 5), four

5/16’’ nuts (item 6) and four sleeves (item 7) (see

location of the parts in the parts breakdown for

snowblower).

5) Removerearsupportplate(item8).

6) Removeinputshaft(item9).

7) Changethebelt(item10).

8) Reinstallthepartsbyreversingthesteps.Tighten

alltheboltsfirmly.

SNOWBLOWERPULLEYREPLACEMENT

1) Repeat steps 1 to 6 in the Belt Replacement

section.

2) Untighten the set screws (item 11) on the top

bearing. The bottom bearing must not have set

screw.

3) Remove the bearings (item 12 or 13) from the

requiredpulleys.

4) Remove damaged pulley (item 14 or 15) and

reinstallnewone.

5) Reinstallthepartsbyreversingthesteps

NOTE:Tightenthesetscrewsat94lb

in.

Tightenfirmlyallthebolts.

WARNING

TOPREVENTINJURIES:

Parkthevehicleonaflatsurface

DisengagetheP.T.O.

Lowertheattachmenttotheground.

Applyparkingbrake.

Stopthemotorandremovetheignitionkey.

Wait until all moving parts have stopped before

leavingthedriver’sseat.

DANGER

CONTACT WITH ROTATING DRIVELINE CAN

CAUSESEVEREINJURYORDEATH.

Operate only when all driveline, tractor and

equipmentguardsareinplace.

Besuredrivelineissecurelyattachedandlocked

atbothendsbeforeoperating.

DISMOUNTING&STORAGE

Lowertheparkingstandthenremovethesnowblower

fromthe3pointshitch

ATTENTION:Alwaysinstalltheprotectivecoverson

theendsofthehydraulichoseswhentheyare

disconnected.Thisistopreventanypollutantsfrom

enteringthevehicle'saccessory’shydraulicsystem.

ATTENTION:Cleanupalloilspillstoprevent

accidents.

WARNING

TOPREVENTINJURIES:

Parkthevehicleonaflatsurfaceinawellventilated

area.

DisengagetheP.T.O.

Lowertheaccessoryandstoptheengine

Applyparkingbrake.

Wait until all moving parts have stopped before

leavingthedriver’sseat.

Usewheelchocks.

SNOWBLOWERDISMOUNTING ENDOFSEASONSTORAGE

a) Clean thoroughly and repaint all parts from which

painthasworn.

b) List the replacement parts that will be needed for

thenextseason.

c) Storethecomponentsinadryplace.

d) FollowtheinstructionsintheLubricationsection.

TROUBLESHOOTING

*Pleaserefertopartsbreakdownsectionforpartsidentification.

PROBLEM POSSIBLECAUSES CORRECTIVEACTION

Snowblowervibratesoris Damagedpulley. Replacepulley.

abnormallynoisy. Damageddriveshaft. Replacedriveshaft.

Damagedbearing. Replacebearing.

Damagedfan. Dismount&repairorreplacefan.

Drivelineisnotwellinstalled. Reinstall the driveline according to the

instructionsinStep3.

The PTO drive shaft angle is

morethan35degree

Lowerthesnowblower

The snowblower input shaft and

tractor output shaft are not

parallel

Adjust the top link of the 3 points

hitch

Oneorbothsectionsoftheauger

isbent.

Replaceoneorbothsectionsofauger.

Oneorbothsectionsoftheauger

havestoppedturning.

Shearboltisprobablybroken. Replace shear bolt (for identification,

see Parts List "Snowblower"). Also see

"Maintenance"section.

Snowblowerstoppedturning. Thebeltisdamagedorsnapped. Check & replace damaged belt (see

instructionsinsection:Beltreplacement

&adjustments.

Damageddriveshaft. Replacedriveshaft.

Beltiswornataspecificpoint. Snowblower was engaged when

alreadyplugged.

Makesureauger&fanarenotplugged

orfrozenbeforeengagingsnowblower.

Chuterotationisdifficult. Dirtoricemaybeunderneath

chute.

Cleanthebaseofchute&therotation

ring.

Thebaseofthechuteorthe

rotationringmaybedamagedor

bent.

Replacedefectiveparts.

Thechuteplugseasily. Vehicle engine is turning too

slowly.

AlwayshaveengineatfullR.P.M.when

usingthesnowblower.

Advancing too quickly with

vehicle.

Reduce speed. Allow snowblower to

ingestsnowatitsownspeed.

Snowblowerdigsintoground. Groundisnotfrozenortoosoft. Adjust skid shoes lower so they may

bettersupportthesnowblower.

Snowblower does not raise

evenly.

Uneven tire pressure from one

side to another or 3 points hitch

misinstalled

Refertothevehicle’sownermanualfor

tirepressure.

Checkandadjusttractortirepressure.

Tire pressure must be even on both

sidesofvehicle.

PARTLIST

3POINTSSNOWBLOWER56’’

O/L=ObtainLocally

PARTLIST

3POINTSSNOWBLOWER56’’

Ref.

Réf.

Englishdescription Descriptionfrançaise

Qty.

Qté.

Part#

Pièce#

31 Knob Bouton 2 102020

32 Timingbelt640

8MT

50 Courroiesynchronisée640

8MT

50 1 105765

33 Sprocket Pignon 1 106488

34 Sprocket Pignon 1 106313

35 Bearingwithsetscrew Roulementàbillesavecvisàpression 4 103242

36 Bearingwithsetscrew Roulementàbillesavecvisàpression 3 102755

37 Lockpin Tigedeverrouillage 1 103563

38 Rotationring Anneauderotation 1 103943

39 Inputshaft Arbred'entré 1 105771

40 Chuteshovel Pelleàgoulotte 1 105700

41 Chuteshovelsupport Supportdepelleàgoulotte 1 105701

42 Key1/4"x1/4"x1.000" Clé1/4"x1/4"x1.000" 1 102017

43 Key1/4"x1/4"x2" Clé1/4"x1/4"x2" 3 102922

44 Rotationbushing Coussinetderotation 4 103946

45 Flangette Flangette 2 102680

46 Flangette Flangette 2 102213

47 Oillitebushing Coussinetimprégnéd'huile 2 102784

48 Nylonflatwasher7/16" Rondelleplatedenylon7/16" 2 102011

49 Hairpin4mm Goupilleàressort4mm 3 102054

50 Hex.bolt1/4"n.c.x3/4"GR5 Boulonhex.1/4"n.c.x3/4"GR5 6 O/L

51 Hex.bolt1/4"n.c.x21/2"GR5 Boulonhex.1/4"n.c.x21/2"GR5 1 O/L

52 Hex.bolt5/16"n.c.x3/4"GR5 Boulonhex.5/16"n.c.x3/4"GR5 2 O/L

53 Hex.bolt5/16"n.c.x21/4"GR8 Boulonhex.5/16"n.c.x21/4"GR8 1 O/L

54 Hex.bolt5/16"n.c.x41/2"GR5 Boulonhex.5/16"n.c.x41/2"GR5 4 O/L

55 Hex.bolt3/8"n.c.x3/4"GR5 Boulonhex.3/8"n.c.x3/4"GR5 4 O/L

56 Hex.bolt3/8"n.c.x2"GR5 Boulonhex.3/8"n.c.x2"GR5 1 O/L

57 Hex.bolt1/2"n.c.x11/2"GR5 Boulonhex.1/2"n.c.x11/2"GR5 2 O/L

58 Hex.bolt1/2"n.c.x33/4"GR5 Boulonhex.1/2"n.c.x33/4"GR5 2 O/L

59 Hex.bolt5/8"n.c.x31/2"GR5 Boulonhex5/8"n.c.x31/2"GR5 2 O/L

60 Carriagebolt1/4"n.c.x3/4"GR5 Boulonàcarrosserie1/4"n.c.x3/4"GR5 6 O/L

O/L=ObtainLocally

PARTLIST

3POINTSSNOWBLOWER56’’

Ref.

Réf.

Englishdescription Descriptionfrançaise

Qty.

Qté.

Part#

Pièce#

1 56"Framewithdecals&cuttingedge Châssis56"avecdécalquesetracloir 1 106782

2 Fan Éventail 1 106727

3 Drivelineguardwithsafetydecal Gardedel'arbreàcardanavecdéc.desec. 1 106783

4 Link Lien 1 106729

5 ParkingStand PieddeStationnement 1 106730

6 RightLeverArm BrasdeLevierDroit 1 106731

7 LeftLeverArm BrasdeLevierGauche 1 106732

8 Sleeve Douille 1 106733

9 Supportd'engrenage Gearsupport 1 106734

10 Sleeve Douille 2 106735

11 Chutewithsafetydecal Goulotteavecdécalquedesécurité 1 106784

12 Auger56"left Vis56"gauche 1 106518

13 Auger56"right Vis56"droite 1 106519

14 Leftskidshoe Patingauche 1 105795

15 Rightskidshoe Patindroit 1 105796

16 Rearsupportplate Plaquedesupportarrière 2 106487

17 Sleeve Douille 4 106370

18 Reinforcement Renfort 1 105484

19 Shaft56" Arbre56" 1 106485

20 Cuttingedge56" Racloir56" 1 106486

21 Gearboxsupport Supportdeboîted'engrenage 1 105787

22 Shearplate Plaquedecisaillement 1 103933

23 Handguard Fourcheprotectrice 1 102012

24 Shearbolt/N.I.L.N.(auger)pkg

10 Boulondeséc./É.G.N.(vis)pqt

10 2 104000

25 Shearbolt/N.I.L.N.(fan)pkg

10 Boulondeséc./É.G.N.(éven.)pqt

10 1 105627

26 Pinwithhairpin4mm Goupilleavecgoupilleàressort4mm 1 106736

27 Pinwithhairpin4mm Goupilleavecgoupilleàressort4mm 2 106738

28 GearBoxRightRotation Boîted'EngrenageRotationDroite 1 106714

29 Driveline ArbreàCardan 1 106715

30 Nylonflatwasher11/32" Rondelleplatedenylon11/32" 2 102009

O/L=ObtainLocally

PARTLIST

3POINTSSNOWBLOWER56’’

Ref.

Réf.

Englishdescription Descriptionfrançaise

Qty.

Qté.

Part#

Pièce#

61 Carriagebolt5/16"n.c.x3/4"GR5 Boulonàcarrosserie5/16"n.c.x3/4"GR5 8 O/L

62 Carriagebolt5/16"n.c.x1"GR5 Boulonàcarrosserie5/16"n.c.x1"GR5 9 O/L

63 Hex.boltM6x1.00x40GR8.8 Boulonhex.M6x1.00x40GR8.8 1 O/L

64 NylonInsertlockNut1/4"n.c. Écrouàgarnituredenylon1/4"n.c. 7 O/L

65 NylonInsertlockNut5/16"n.c. Écrouàgarnituredenylon5/16"n.c. 15 O/L

66 NylonInsertlockNut3/8"n.c. Écrouàgarnituredenylon3/8"n.c. 5 O/L

67 NylonInsertlockNut1/2"n.c. Écrouàgarnituredenylon1/2"n.c. 4 O/L

68 NylonInsertlockNut5/8"n.c. Écrouàgarnituredenylon5/8"n.c. 2 O/L

69 NylonInsertlockNutM6x1.00 ÉcrouàgarnituredenylonM6x1.00 1 O/L

70 Flangenut1/4"n.c. Écrouàbride1/4"n.c. 2 O/L

71 Stoverlocknut5/16"n.c. Écroudeblocage5/16"n.c. 7 O/L

72 Flatwasher1/4"hole Rondelleplate1/4"trou 4 O/L

73 Flatwasher5/16"hole Rondelleplate5/16"trou 8 O/L

74 Lockwasher1/4" Rondelledeblocage1/4" 4 O/L

75 Socketheadsetscrew1/4''n.c.x5/16''

(knurled)

Visàpressionàtêteplate6PC1/4''n.c.x

5/16''

(moletée)

1 O/L

76 SocketHeadCapScrewM5x0.80x10 VissixPCtêterondeM5x0.80x10 2 O/L

77 Serialnumber Numérodesérie 1 REF

78 MadeinCanadadecal DécalqueFabriquéauCanada 1 REF

79 Decaldangerauger Decalquedangervis 1 105126

80 Decalreadinstructions Decalquelireinstructions 1 105130

81 Decalwarningsafety Decalqueavertissementsécurité 1 105131

82 DecalPTO DécalquePTO 1 105852

83 Dangerdecalchute Décalquedangergoulotte 1 105127

84 Redreflectordecal Décalqueréflecteurrouge 4 106814

85 Yellowreflectordecal Décalqueréflecteurjaune 2 106815

86 MahindraMaxdecal DécalqueMahindraMax 1 106473

Page is loading ...

Bercomac BER53PT User manual

Brand: Bercomac

Model: BER53PT

Category: Snow throwers

Type: User manual

This manual is also suitable for

BER3PTSB56H

Download PDF

report

in other languages

français: Bercomac BER53PT Manuel utilisateur

Bercomac BER53PT User manual

This manual is also suitable for

Bercomac BER53PT User manual

in other languages

Related papers

Other documents