Krone BA ActiveMow R 360 Operating instructions

Original operating instructions

Document number: 150000864_06_us

Version: 12/10/2023

Rear mounted mower

ActiveMow R 360

From machine number: 1136331

2

ActiveMow R 360

Original operating instructions 150000864_06_us

Contact

Krone North America, Inc.

12121 Forest Dr.

Olive Branch, MS 38654

U.S.A.

Phone + 1 662 913-7171

Fax + 1 662 913-7137

Email [email protected]

Internet www.krone-northamerica.com

Information for enquiries and orders

Year

Machine number

Model

Your dealer's contact details

3

ActiveMow R 360

Original operating instructions 150000864_06_us

For information on your KRONE machines, also refer to mykrone.green. After you have

registered, you can generate and manage your machines via the machine number so that you

can view the machine data. Via your personal account, you can also access all KRONE

Services.

Technical Information Center (TIC)

Technical and service-relevant information on your KRONE machines can also be found in the

Technical Information Center. All information can be searched using a full-text search, such as

operating instructions, spare parts information, training documents (qualification-based), error

code and parameter descriptions, guided troubleshooting, video tutorials and much more.

Table of contents

4

ActiveMow R 360

Original operating instructions 150000864_06_us

1 Information on This Document.................................................................................................7

1.1 Validity .........................................................................................................................................7

1.2 Significance of the document.......................................................................................................7

1.3 Re-ordering ..................................................................................................................................7

1.4 Applicable documents..................................................................................................................7

1.5 Target group of this document .....................................................................................................7

1.6 How to use this document............................................................................................................7

1.6.1 Directories and references...........................................................................................................7

1.6.2 Information on direction ...............................................................................................................8

1.6.3 Term “machine”............................................................................................................................8

1.6.4 Figures .........................................................................................................................................8

1.6.5 Scope of the document ................................................................................................................8

1.6.6 Means of representation ..............................................................................................................8

1.6.7 Conversion table ........................................................................................................................10

2 Safety ........................................................................................................................................12

2.1 Intended use ..............................................................................................................................12

2.2 Reasonably foreseeable misuse................................................................................................12

2.3 Service life of the machine.........................................................................................................13

2.4 Basic safety instructions ............................................................................................................13

2.4.1 Importance of operating instructions..........................................................................................13

2.4.2 Personnel qualification of the operating personnel ....................................................................13

2.4.3 Personnel qualification of the technicians..................................................................................14

2.4.4 Children in danger......................................................................................................................14

2.4.5 Connecting the machine ............................................................................................................14

2.4.6 Structural modifications on the machine ....................................................................................14

2.4.7 Additional equipment and spare parts .......................................................................................14

2.4.8 Jobs on the machine..................................................................................................................15

2.4.9 Operational safety: Technically sound condition........................................................................15

2.4.10 Danger zones.............................................................................................................................16

2.4.11 Ensuring functionality of safety devices .....................................................................................18

2.4.12 Personal protective equipment ..................................................................................................18

2.4.13 Safety sign on the machine........................................................................................................19

2.4.14 Road safety................................................................................................................................19

2.4.15 Parking the machine safely .......................................................................................................20

2.4.16 Consumables .............................................................................................................................20

2.4.17 Dangers arising from environment.............................................................................................21

2.4.18 Sources of danger on the machine ............................................................................................22

2.4.19 Dangers in connection with certain activities: Working on the machine ....................................23

2.4.20 Behaviour in dangerous situations and in case of accidents .....................................................24

2.5 Safety routines ...........................................................................................................................25

2.5.1 Shutting down and safeguarding the machine...........................................................................25

2.5.2 Securing raised machine and machine parts against lowering..................................................25

2.5.3 Carrying out oil level check and oil and filter element changes safely.......................................26

2.6 Safety sign on the machine........................................................................................................26

2.7 Information labels on the machine .............................................................................................31

2.8 Safety equipment .......................................................................................................................34

2.8.1 SMV emblem .............................................................................................................................34

3 Machine Description................................................................................................................36

3.1 Machine overview ......................................................................................................................36

3.2 Overload protections on the machine ........................................................................................37

3.3 Labelling.....................................................................................................................................37

3.4 Road travel lighting ....................................................................................................................38

3.5 Pole protection mechanism........................................................................................................39

4 Technical data ..........................................................................................................................40

4.1 Dimensions ................................................................................................................................40

4.2 Weights ......................................................................................................................................40

4.3 Area output ................................................................................................................................40

4.4 Cutting height.............................................................................................................................40

4.5 Technically permitted maximum speed (road travel) .................................................................40

Table of contents

ActiveMow R 360

Original operating instructions 150000864_06_us 5

4.6 Airborne noise emission.............................................................................................................40

4.7 Ambient temperature .................................................................................................................40

4.8 Requirements for tractor - power ...............................................................................................41

4.9 Tractor requirements – hydraulics .............................................................................................41

4.10 Requirements for the tractor – electrics .....................................................................................41

4.11 Machine equipment....................................................................................................................41

4.12 Consumables .............................................................................................................................41

4.12.1 Oils.............................................................................................................................................42

4.12.2 Lubricating greases....................................................................................................................42

5 Control and Display Elements ................................................................................................43

5.1 Hydraulic control units of the tractor ..........................................................................................43

6 Initial Operation........................................................................................................................44

6.1 Checklist for initial operation ......................................................................................................44

6.2 Adapting coupling points............................................................................................................45

6.3 Mounting the universal shaft on the machine ............................................................................46

6.4 Adapting universal shaft.............................................................................................................47

7 Start-up .....................................................................................................................................48

7.1 Calculating the ballasting of the tractor-machine combination...................................................48

7.2 Connecting the machine to the tractor .......................................................................................51

7.3 Connecting hydraulic hoses.......................................................................................................52

7.4 Connecting road travel lighting ..................................................................................................53

7.5 Installing universal shaft.............................................................................................................54

8 Operation ..................................................................................................................................55

8.1 Front guard ................................................................................................................................55

8.1.1 Folding up the front guard..........................................................................................................55

8.1.2 Fold down the front guard ..........................................................................................................56

8.2 Side guard..................................................................................................................................56

8.2.1 Folding up side guard (transport position) .................................................................................57

8.2.2 Folding down side guard (working position)...............................................................................57

8.3 Operating support jack for "Series" version ............................................................................... 57

8.3.1 Moving support jack into transport position................................................................................58

8.3.2 Moving support jack into support position..................................................................................58

8.4 Mounting/dismounting support jack – for version with "Additional support jacks"...................... 58

8.4.1 Mounting support jack................................................................................................................59

8.4.2 Dismounting support jack...........................................................................................................59

8.5 Closing/opening the stop cock ...................................................................................................60

8.6 Lowering machine from transport position to working position ..................................................60

8.7 Field mode .................................................................................................................................62

8.8 Field mode on slopes.................................................................................................................63

9 Driving and Transport .............................................................................................................64

9.1 Preparing machine for road travel..............................................................................................65

9.2 Switching off the machine ..........................................................................................................66

9.3 Preparing the machine for shipment ..........................................................................................67

9.3.1 Checklist for the transport of the machine .................................................................................67

9.3.2 Lifting the machine.....................................................................................................................67

9.3.3 Lashing the machine..................................................................................................................68

10 Settings.....................................................................................................................................69

10.1 Setting the mower in working position .......................................................................................69

10.2 Setting the cutting height ...........................................................................................................69

10.3 Checking/setting locking of side guards.....................................................................................70

10.4 Increasing/reducing ground pressure ........................................................................................71

10.4.1 Setting the relief springs for the mower .....................................................................................71

10.4.2 Setting the relief spring for the carrying bar ...............................................................................72

11 Maintenance - General Information........................................................................................73

11.1 Maintenance table......................................................................................................................73

11.1.1 Maintenance – Before the season .............................................................................................73

Table of contents

6

ActiveMow R 360

Original operating instructions 150000864_06_us

11.1.2 Maintenance – After the season ................................................................................................74

11.1.3 Maintenance - Once after 50 hours ...........................................................................................75

11.1.4 Maintenance - Every 10 hours, but at least once a day.............................................................75

11.1.5 Maintenance - Every 50 hours ...................................................................................................75

11.1.6 Maintenance - Every 200 hours .................................................................................................75

11.2 Tightening torques .....................................................................................................................75

11.3 Deviating tightening torques ......................................................................................................78

11.4 Venting the friction clutch...........................................................................................................79

11.5 Checking guard cloths ...............................................................................................................81

11.6 Cleaning the machine ................................................................................................................82

12 Maintenance - Hydraulic System............................................................................................83

12.1 Hydraulic oil ...............................................................................................................................84

12.2 Checking hydraulic hoses ..........................................................................................................84

13 Maintenance - Gearbox ...........................................................................................................85

13.1 Overview of gearboxes ..............................................................................................................85

13.2 Input gearbox .............................................................................................................................86

13.3 Main gearbox .............................................................................................................................87

14 Maintenance - Cutterbar..........................................................................................................88

14.1 Rotary hub .................................................................................................................................89

14.2 Replacing the shear bolt at the rotary hub .................................................................................90

14.3 Check/change blades ................................................................................................................91

14.4 Check/replace retaining bolts.....................................................................................................95

14.5 Checking/replacing the blade carrier .........................................................................................97

14.6 Checking impact stops on the cutterbar.....................................................................................99

14.7 Check/replace cutting discs/mower drums ..............................................................................100

14.8 Checking oil level .....................................................................................................................102

15 Maintenance – Lubrication....................................................................................................104

15.1 Lubricating universal shaft .......................................................................................................104

15.2 Lubrication chart – Machine.....................................................................................................105

16 Malfunction, cause and remedy ...........................................................................................107

16.1 General disturbances...............................................................................................................107

17 Waste disposal.......................................................................................................................108

18 Index........................................................................................................................................109

Information on This Document 1

Validity 1.1

ActiveMow R 360

Original operating instructions 150000864_06_us 7

1 Information on This Document

1.1 Validity

This document is valid for machines of type:

ActiveMow R 360

All information, illustrations and technical data in this document correspond to the latest state at

the time of publication.

We reserve the right to make design changes at any time and without notification of reasons.

1.2 Significance of the document

This is an important document. It is addressed to the user and contains safety-relevant

information.

Prior to starting work, read the complete document and observe its contents.

Keep this document ready to hand in the document storage tube for the user of the

machine, see Page36.

Hand over this document to subsequent users.

1.3 Re-ordering

If this document has become completely or partially unusable or if another language is required,

you can request a replacement document by quoting the document number indicated on the

cover sheet. Furthermore, the document can also be downloaded online via

KRONEMEDIAhttps://media.mykrone.green or via the TIChttps://mykrone.green/control/

subsystemauth?system=S017.

1.4 Applicable documents

To ensure that the machine is used safely and as intended, observe the following further

applicable documents.

• Operating instructions for universal shaft

• With front mounted mower: Operating instructions front mounted mower

• Assembly instructions, KRONE

• Spare parts list, KRONE

1.5 Target group of this document

This document aims at the operator of the machine who fulfills the minimum requirements of

personnel qualification,see Page13.

1.6 How to use this document

1.6.1 Directories and references

Contents/headers

The contents and headers in this document ensure quick orientation in the chapters.

1 Information on This Document

1.6 How to use this document

8

ActiveMow R 360

Original operating instructions 150000864_06_us

Index

The index contains catchwords in alphabetical order which enable to find information on a

desired topic easily. The index can be found on the last pages of this document.

Cross references

Cross references to another place in the document or to another document are in the text with

page number.

Examples:

• Check the tight seat of all screws on the machine, see Page8. (INFO: If you use an

electronic version of this document, click on the link to go to the specified page.)

• For further information, refer to the operating instructions of the universal shaft

manufacturer.

1.6.2 Information on direction

Directional information in this document, such as front, rear, right and left, applies in the

direction of travel of the machine.

1.6.3 Term “machine”

Throughout the rest of this document, the “rear mounted mower” will also be referred to as the

“machine”.

1.6.4 Figures

The figures in this document do not always represent the exact machine type. The information

that refers to the figure always corresponds to the machine type of this document.

1.6.5 Scope of the document

In addition to standard equipment, accessories kits and versions of the machine are described

in this document. Your machine may deviate from this document.

1.6.6 Means of representation

Icons in the text

The following means of representation (icons) are used to present the text more clearly:

This arrow characterizes an action step. Several arrows in a row identify a sequence of

actions to be performed step by step.

This icon identifies a prerequisite that has to be fulfilled to perform an action step or a

sequence of actions.

This arrow marks the intermediate result of an action step.

This arrow identifies the result of an action step or sequence of actions.

This bullet point identifies an enumeration. If the bullet point is intended, it identifies the

second level of the enumeration.

Information on This Document 1

How to use this document 1.6

ActiveMow R 360

Original operating instructions 150000864_06_us 9

Icons in figures

The following icons can be used in illustrations:

Icon Explanation Icon Explanation

1

Reference sign for part

I

Position of a part (e.g. move from

position I to position II)

X

Dimensions (e. g. also W = width,

H = height, L = length)

Magnification of display detail

LH

Left side of machine

RH

Right side of machine

Direction of travel Direction of motion

Reference line for visible material Reference line for covered mater-

ial

Centre line Cable routes

Open Closed

Apply liquid lubricant (e.g. lubric-

ating oil)

Apply lubricating grease

Warning signs

Warnings of dangers are separated from the remaining text as warning signs and are identified

with a danger sign and signal words.

The warning signs must be read and the measures must be observed in order to prevent

personal injury.

Explanation of danger sign

This is the danger sign that warns of a risk of injury.

Please observe all notes marked with the danger sign in order to avoid injuries or death.

Explanation of signal words

DANGER

The signal word DANGER warns of a hazardous situation which will result in serious injuries

or death if the warning sign is ignored.

WARNING

The signal word WARNING warns of a hazardous situation which will result in serious injuries

or death if the warning sign is ignored.

1 Information on This Document

1.6 How to use this document

10

ActiveMow R 360

Original operating instructions 150000864_06_us

CAUTION

The signal word CAUTION warns of a hazardous situation which will result in minor to

moderate injuries if the warning sign is ignored.

Example of a warning sign:

WARNING

Eye damage caused by flying dirt particles

When cleaning with compressed air, dirt particles are ejected at high speed and could get into

the eyes. Therefore eyes could be hurt.

Keep people away from the working area.

Wear personal protective equipment when performing cleaning work with compressed air

(e.g. eye protection).

Warnings of property damage/environmental damage

Warnings of property/environmental damage are separated from the remaining text and marked

with "Notice".

Example:

NOTICE

Gearbox damage due to low oil level

The gearboxes could be damaged when the oil level is too low.

Check gear oil level at regular intervals and top up oil, if necessary.

Check gear oil level approx. 3 to 4 hours after the machine has been switched off. Check

oil level only when machine is in horizontal position.

Notices with information and recommendations

Additional information and recommendations for trouble-free and productive operation of the

machine are separated from the remaining text and marked with “Information”.

Example:

INFO

Each safety sign is provided with an order number and can be ordered directly from the

manufacturer or from an authorised specialist dealer.

1.6.7 Conversion table

The following table can be used to convert metric units into US units.

Size SI units (metric) Factor Inch-pound units

Unit name Abbrevi-

ation

Unit name Abbrevi-

ation

Area Hectare ha 2.47105 Acre acres

Volume flow Litres per minute L/min 0.2642 US gallons per

minute

gpm

Cubic metres

per hour

m³/h 4.4029

Information on This Document 1

How to use this document 1.6

ActiveMow R 360

Original operating instructions 150000864_06_us 11

Size SI units (metric) Factor Inch-pound units

Unit name Abbrevi-

ation

Unit name Abbrevi-

ation

Force Newton N 0.2248 Pound force lbf

Length Millimetre mm 0.03937 Inch in.

Metre m 3.2808 Foot ft.

Power Kilowatt kW 1.3410 Horsepower hp

Pressure Kilopascal kPa 0.1450 Pounds per

square inch

psi

Megapascal MPa 145.0377

bar (non-SI) bar 14.5038

Torque Newtonmeter Nm 0.7376 pound-foot or

foot-pound

ft∙lbf

8.8507 pound-inch or

inch-pound

in∙lbf

Temperature Degrees Celsius °C °Cx1.8+32 Degrees

Fahrenheit

°F

Velocity Metres per

minute

m/min 3.2808 Feet per minute ft/min

Metres per

second

m/s 3.2808 Feet per second ft/s

Kilometres per

hour

km/h 0.6215 Miles per hour mph

Volumes Litres L 0.2642 US gallon US gal.

Millilitre ml 0.0338 US ounce US oz.

Cubic centi-

metre

cm³ 0.0610 Cubic inch in³

Weight Kilogram kg 2.2046 Pound lbs

2 Safety

2.1 Intended use

12

ActiveMow R 360

Original operating instructions 150000864_06_us

2 Safety

2.1 Intended use

This machine is a mower and is used to mow crops.

The crops designated for the intended use of this machine are stalk and leaf crops growing on

the ground.

The machine is designed exclusively for use in agriculture and may only be used when

• all safety devices are available according to the operating instructions and are located in the

protective position.

• all safety instructions of the operating instructions have been observed and complied with,

both in chapter “Basic safety instructions”, see Page13, and directly in the chapters of the

operating instructions.

The machine may be used only by people who satisfy the personnel qualification requirements

designated by the machine manufacturer, see Page13.

These operating instructions are part of the machine and must therefore be at hand when the

machine is in use. The machine may be operated only when the operator has received training

and in compliance with these operating instructions.

If the machine is used for applications which are not described in these operating instructions,

this may result in serious injuries or death and damage to the machine and other property.

Unauthorised modifications to the machine may affect the properties of the machine or disrupt

the proper operation. For this reason, unauthorised modifications shall exclude any liability of

the manufacturer for consequential damage.

The intended use shall also include the adherence to the operating, maintenance and repair

conditions set by the manufacturer.

2.2 Reasonably foreseeable misuse

Any use beyond the intended usesee Page12 is regarded as improper use and is therefore

misuse according to the Machinery Directive. The manufacturer is not liable for damage

resulting from this, the user alone bears the risk.

Such misuse is for example:

• Processing of crops which are outside the intended use of the machine,see Page12

• Transport of people

• Transport of goods

• Exceeding the permitted technical gross weight

• Non-compliance with the safety labels on the machine and safety notes in the operating

instructions

• Performing troubleshooting, setting, cleaning, repair and maintenance work contrary to the

information in the operating instructions

• Unauthorised modifications to the machine

• Attachment of unauthorised or unapproved additional equipment

• Use of spare parts which are not KRONE original spare parts

• Stationary operation of the machine

Unauthorised modifications to the machine may affect the properties of the machine or disrupt

proper operation. For this reason, unauthorised modifications will exclude any liability of the

manufacturer for consequential damage.

Safety 2

Service life of the machine 2.3

ActiveMow R 360

Original operating instructions 150000864_06_us 13

2.3 Service life of the machine

• The service life of this machine depends on its proper operation and maintenance as well

as the operating and harvesting conditions.

• By heeding the instructions and information in these operating instructions, permanent

operational readiness and a long service life of the machine can be achieved.

• After each operating season, inspect the entire machine for wear and other damage.

• Replace damaged and worn components before recommissioning the machine.

• Carry out a full technical inspection of the machine after five years of machine operation

and make a decision on further machine usage taking the results of this inspection into

account.

• Theoretically, the service life of this machine is unlimited as all worn or damaged

components can be replaced.

2.4 Basic safety instructions

Non-compliance with the safety instructions and warnings

Non-compliance with the safety instructions and warnings may result in injuries and damage to

the environment and property.

2.4.1 Importance of operating instructions

The operating instructions are an important document and a part of the machine. They are

intended for the user and contain information that is relevant to safety.

Only the procedures specified in the operating instructions are safe. If the operating instructions

are not followed, there is a risk of serious or even fatal injuries.

Prior to using the machine for the first time, read and observe the "Basic safety notices"

completely.

Prior to starting work, read and observe the respective sections in the operating instructions

too.

Keep the operating instructions ready to hand for the user of the machine in the document

storage tube, see Page36.

Hand over the operating instructions to subsequent users.

2.4.2 Personnel qualification of the operating personnel

If the machine is not used properly, people may be seriously injured or killed. To avoid

accidents, each person who works with the machine must satisfy the following minimum

requirements:

• He is physically capable of controlling the machine.

• He can work safely with the machine in accordance with these operating instructions.

• He understands the method of operation of the machine within the scope of his work and

can identify and avoid the dangers associated with the work.

• He has read the operating instructions and can implement the information in the operating

instructions accordingly.

• He is familiar with driving vehicles safely.

• For road travel he has adequate knowledge of the highway code and has the stipulated

driving licence.

2 Safety

2.4 Basic safety instructions

14

ActiveMow R 360

Original operating instructions 150000864_06_us

2.4.3 Personnel qualification of the technicians

If the work (assembly, conversion, modification, extension, repairs, retrofitting) is performed

improperly on the machine, people may be seriously or fatally injured. To avoid accidents,

everyone who performs work according to these instructions must meet the following minimum

requirements:

• Qualified professional, with relevant training.

• Capable of assembling the (partially) disassembled machine according to the assembly

instructions provided by the manufacturer.

• He is capable, e.g. by attending a training course, of extending, modifying or repairing the

function of the machine according to the relevant instructions provided by the manufacturer.

• He has read the operating instructions and can implement the information in the operating

instructions accordingly.

• Ability to perform the work safely according to these instructions.

• Understands the mode of operation of the work to be performed and the machine and is

able to identify and avoid risk in carrying out the necessary work.

• Has read these instructions and is able to implement the information explained in these

instructions accordingly.

2.4.4 Children in danger

Children are not in a position to assess dangers and behave unpredictably.

Thus children are particularly at risk.

Keep children away from the machine.

Keep children away from consumables.

Make sure that there are no children in the danger zone, especially when starting and

triggering machine movements.

2.4.5 Connecting the machine

When tractor and machine are not correctly connected, there is a risk of causing serious

accidents.

When connecting, follow all operating instructions:

• the operating instructions of the tractor

• the operating instructions of the machine, see Page48

• the operating instructions of universal shaft

Observe the changed driving behaviour of the combination.

2.4.6 Structural modifications on the machine

Structural modifications and extensions that were not approved by KRONE can impair the

functionality, operational safety and also the road traffic certification of the machine. As a result,

persons can be seriously injured or killed.

Any structural modifications and extensions that are not authorised by KRONE are not

permitted.

2.4.7 Additional equipment and spare parts

Additional equipment and spare parts that do not correspond to the requirements of the

manufacturer may affect the operational safety of the machine and cause accidents.

To ensure operational safety, use original parts or standard parts which correspond to the

requirements of the manufacturer.

Safety 2

Basic safety instructions 2.4

ActiveMow R 360

Original operating instructions 150000864_06_us 15

2.4.8 Jobs on the machine

Passengers

Passengers may be seriously injured by the machine or fall off the machine and run over.

Ejected objects may strike and injure passengers.

Never carry passengers on the machine.

2.4.9 Operational safety: Technically sound condition

Operation only after proper commissioning

The operational safety of the machine is not guaranteed without proper commissioning in

accordance with these operating instructions. This may result in accidents and people may be

seriously or fatally injured.

Use the machine only after proper commissioning, see Page48.

Technically sound state of the machine

Improper maintenance and setting could influence the operational safety of the machine and

cause accidents. Thus there is a risk of serious injuries or death.

All maintenance and setting work must be performed according to the chapters

“Maintenance and Setting”.

Before performing any maintenance and setting work, shut down and safeguard the

machine, see Page25.

Danger resulting from damage to the machine

Damage to the machine may impair the operational safety of the machine and cause accidents.

As a result, people may be seriously injured or killed. The following parts of the machine are

particularly important for safety:

• Safety Devices

• Connecting devices

• Lighting

• Hydraulics

• Universal shaft

If there are doubts about the operational safety of the machine, for example due to an

unexpected change to the operational behaviour, visible damage or leaking consumables:

Shut down and safeguard the machine, see Page25.

Immediately eliminate potential causes of damage, for example heavy soiling, or tighten

slack screws.

Determine the cause of damage according to these operating instructions and repair the

damage, if possible, see Page107.

In case of damage which may affect operational safety and cannot be repaired according to

these operating instructions: Have damage repaired by a qualified service centre.

2 Safety

2.4 Basic safety instructions

16

ActiveMow R 360

Original operating instructions 150000864_06_us

Technical limit values

If the technical limit values of the machine are not observed, the machine may be damaged. As

a result, accidents may occur and people may be seriously or fatally injured. With regard to

safety, it is especially important to observe the following technical limit values:

• maximum permitted operating pressure of the hydraulics

• maximum permitted drive speed

• maximum permitted axle loads of the tractor

• maximum permitted transport height and width

Comply with limit values, see Page40.

2.4.10 Danger zones

If the machine is switched on, its surrounding can present a danger zone.

Avoid entering the danger zone of the machine by observing the minimum safety distance.

If the safety distance is not observed, people may be seriously injured or killed.

Do not switch on the drives and engine if the minimum safety distance has not been

observed.

If people fail to observe the minimum safety distance, switch off the drives.

Switch the machine off in shunting and field mode.

The safety distance is:

For machine in shunting and field mode

In front of the machine 30m

Behind the machine 5m

On either side of the machine 3m

For machine switched on without driving motion

In front of the machine 3m

Behind the machine 5m

On either side of the machine 3m

The safety distances specified here are minimum distances in terms of intended use. If

necessary, these safety distances must be increased according to the operating and ambient

conditions.

Before working in front of and behind the tractor and in the danger zone of the machine:

Shut down and secure the machine, see Page25. This also applies to brief inspection

work.

Consider the information in all relevant operating instructions:

• the operating instructions for the tractor

• the operating instructions of the machine

• the operating instructions of universal shaft

Danger zone universal shaft

People may be caught, pulled in and seriously injured by the universal shaft.

Observe operating instructions of universal shaft.

Ensure sufficient overlap of section tube and universal shaft guards.

Make sure that the universal shaft guards are mounted and that they are fully functional.

Safety 2

Basic safety instructions 2.4

ActiveMow R 360

Original operating instructions 150000864_06_us 17

Allow the universal shaft locks to engage. There must be no areas of the locking device on

the PTO shaft fork which could cause catching or entrapment (e.g. by annular design,

protective collar around the locking pin).

Attach chains to prevent the universal shaft guards from rotating with the shaft.

Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

Ensure that the selected speed and direction of rotation of the PTO shaft of the tractor

match the permitted speed and direction of rotation of the machine.

Switch off the PTO shaft when the angles between the universal shaft and the PTO shaft

are too large. The machine may be damaged. Parts may be hurled up and cause injury to

people.

Danger zone PTO shaft

People may be caught, pulled in and seriously injured by the PTO shaft and the driven

components.

Before switching on the PTO shaft:

Ensure that all protective devices are mounted and brought into protective position.

Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

Switch off drives if they are not needed.

Danger zone between tractor and machine

People standing between the tractor and machine may be seriously injured or killed if the tractor

rolls away or by carelessness or machine movements:

Before carrying out any work between the tractor and the machine: Always turn off and

secure the machine, see Page25. This also applies to brief inspection work.

If the lifting device must be actuated, instruct all people to keep away from the range of

movement of the lifting device.

Danger zone ejected objects

Crops and foreign bodies may be forcefully flung out and injure or kill people.

Before starting the machine, instruct all people to leave the danger zone of the machine.

If people are in the danger zone of the machine, immediately switch off drives and diesel

engine.

Danger zone when drive is switched on

When the drive is switched on, there is a danger to life caused by rotating machine parts.

Ensure that there are no persons in the danger zone of the machine.

Before starting the machine, instruct all people to leave the danger zone of the machine.

In case of dangerous situations, immediately switch off drives and instruct people to leave

the danger zone.

Danger zone due to trailing machine parts

If machine parts are trailing, people may be seriously injured or killed.

2 Safety

2.4 Basic safety instructions

18

ActiveMow R 360

Original operating instructions 150000864_06_us

After the drives have been switched off, the following machine parts will trail:

• Universal shafts

• Cutting discs

• Conditioner

• Conveying devices

Shut down and safeguard the machine, see Page25.

Do not attempt to approach the machine until all moving machine parts have come to a

standstill.

2.4.11 Ensuring functionality of safety devices

If safety devices are missing or damaged, people may be seriously injured or killed by moving

machine parts.

Replace damaged safety devices.

Mount dismounted safety devices and machine parts again before start-up and move them

to protective position.

If it is doubtful whether all safety devices have been correctly installed and are functional,

have a service centre check them.

Keeping universal shaft guard functional

The overlap of universal shaft and protective cap on the machine must not be less than 50mm.

This minimum overlap is also required for protective devices of wide-angle universal shaft and if

couplings or other components are used. If the operator has to reach between the universal

shaft guard and the protective cap to connect the universal shaft, the clearance on one level

must be at least 50mm. On all levels the clearance must be no more than 150mm.

2.4.12 Personal protective equipment

The wearing of personal protective equipment is an important safety measure. Missing or

unsuitable personal protective equipment increases health risks and injuries.

Personal protective equipment includes, for example:

• Suitable protective gloves

• Safety shoes

• Tight-fitting protective clothing

• Hearing protection

• Protective goggles

• If dust is generated: appropriate breathing protection

Specify and provide personal protective equipment for the particular job.

Use only personal protective equipment which is in proper condition and offers effective

protection.

Adjust personal protective equipment to the person, for example the size.

Remove unsuitable clothing and jewellery (e.g. rings, necklaces) and cover long hair with a

hairnet.

Safety 2

Basic safety instructions 2.4

ActiveMow R 360

Original operating instructions 150000864_06_us 19

2.4.13 Safety sign on the machine

Safety labels on the machine warn of hazards at danger points and are an important component

of the machine's safety equipment. Missing safety labels increase the risk of serious and fatal

injuries.

Clean dirty safety labels.

Each time after cleaning, check to ensure that the safety labels are complete and legible.

Immediately replace missing, damaged and unrecognisable safety labels.

Label spare parts with the required safety labels.

Descriptions, explanations and order numbers of the safety labels, see Page26.

2.4.14 Road safety

Dangers during road travel

Other road users can be put at risk when you drive on public roads and the machine is not

properly illuminated and/or exceeds the maximum dimensions and weights laid down by

national law.

Prior to driving on public roads, ensure that the maximum permissible dimensions, weights

and axle, support and trailer loads are not exceeded which are applicable under national law

for driving on public roads.

Before driving on roads, switch on the road travel lighting and ensure that it functions

properly.

Before driving on roads, close all stop cocks for the hydraulic supply to the machine

between tractor and machine.

Before driving on roads, move the tractor control units to the neutral position and lock them.

Danger when driving on road and field

Hitched and mounted machines change the handling characteristics of the tractor. The handling

characteristics depend for instance on operating state and ground. If changed handling

characteristics are not considered, the driver may cause accidents.

Observe measures for driving on road and field,see Page64.

Dangers if the machine is not prepared properly for road travel

If the machine is not prepared properly for road travel, serious accidents may occur with traffic.

Before driving on roads, prepare the machine for road travel, see Page65.

Danger when cornering with a hitched machine and due to the overall width

Accidents may occur when cornering due to the machine swinging out and also due to the

overall width.

Consider the overall width of the combined tractor and machine.

Consider the larger swivel range when cornering.

Consider people, oncoming traffic and obstacles when turning.

2 Safety

2.4 Basic safety instructions

20

ActiveMow R 360

Original operating instructions 150000864_06_us

Dangers when operating the machine on slopes

The machine may tilt when it is used on slopes. As a result, accidents may occur and people

may be seriously injured or killed.

Do not work and drive on a slope unless the ground of the slope is flat and the adhesion of

the tyres to the ground is ensured.

Turn the machine at low speed. Turn in a large arc.

Avoid driving across a slope because the centre of gravity of the machine will be changed

by payload and by executing machine functions.

Avoid abrupt steering movements on slopes.

Do not move the machine from working position to transport position or from transport

position to working position as long as the machine is used across a slope.

Do not park the machine on slopes.

Observe procedures for operating the machine on slopes, see Page63.

2.4.15 Parking the machine safely

An incorrectly parked and insufficiently safeguarded machine can represent a danger for

people, especially children, and can be set into motion or fall over in an uncontrolled manner.

People may be injured or killed.

Park the machine on a horizontal and level ground capable of bearing the load.

Before adjusting, repairing, servicing and cleaning the machine, ensure that it is securely

positioned.

Observe section “Parking the Machine” in chapter Driving and Transport.see Page66

Before parking: Shut down and safeguard the machine, see Page25.

2.4.16 Consumables

Unsuitable consumables

Consumables which do not comply with the requirements of the manufacturer may impair the

operational safety of the machine and cause accidents.

Use only consumables which comply with the requirements of the manufacturer.

For requirements on consumables, see Page41.

Contamination of hydraulic system and/or fuel system

Foreign objects and/or liquids in the hydraulic system and/or fuel system may impair the

operational safety of the machine and cause accidents.

Clean all connections and components.

Close open connections by means of protective caps.

Page is loading ...

Krone BA ActiveMow R 360 Operating instructions

Krone BA ActiveMow R 360 Operating instructions

Related papers