Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR (2) Owner's manual

Halsey Taylor
Brand
Halsey Taylor
Model
HRF_EBP_SBP_SEBP_ESBP_FR (2)
Category
Sanitary ware
Type
Owner's manual

Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR (2) is a freeze-resistant fountain that is perfect for outdoor use in cold climates. The fountain is equipped with a Freeze Resistant Package (HTFRB1) that is installed on an interior heated wall. The interior space must maintain a minimum temperature of 50° F (10° C) to prevent the water in the fountain from freezing. The fountain is also equipped with an operating cable that allows the user to turn the water on and off from a distance. The fountain is easy to install and comes with all the necessary hardware.

Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR (2) is a freeze-resistant fountain that is perfect for outdoor use in cold climates. The fountain is equipped with a Freeze Resistant Package (HTFRB1) that is installed on an interior heated wall. The interior space must maintain a minimum temperature of 50° F (10° C) to prevent the water in the fountain from freezing. The fountain is also equipped with an operating cable that allows the user to turn the water on and off from a distance. The fountain is easy to install and comes with all the necessary hardware.

PAGE 1 97649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
Halsey Taylor Owners Manual
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
Freeze Resistant Fountains
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
HRFSBP - FR HRFSEBP - FR
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLA-
TION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE
CODES. After installation, leave these instructions inside the fountain for future reference.
This Freeze Resistant Fountain is shipped in two separate cartons. The second carton(s)
contains the Freeze Resistant Package(s) HTFRB1 that are installed on an interior
heated wall. The interior space must maintain a minimum temperature of 50° F (10° C).
Refer to the Freeze Resistant Package for the rough-in dimensions for installation.
Installer
HRFEBP - FR HRFESBP - FR
PAGE 297649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
BUILDING WATER
INLET
1/4" O.D. TUBE
WATER INLET
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the interior heated area must be 50° F
(10° C) or higher. The freeze resistant package may be surface or recessed mounted. If recess mounted the surface of the cover must be flush
with the interior wall surface. The package is furnished with screws for mounting the cover to the box. If the box is recess mounted, do not
fasten the top and bottom of the cover to the box. Use the holes on the front only.
1. Fountains using the MPW Mounting Plate refer to Fig's. 7, 11, or 15 for hanger bracket location and rough-in dimensions.
NOTE: Review separate installation instructions for details of the MPW Mounting Plate.
Fountains using the Wall Plate Assy. refer to Fig's. 3, 5, 9, or 13 for rough-in dimensions.
2. Shown dimensions pertain to installation location (framing must support up to 150 lbs. weight for single fountain and 300 lbs. for dual
fountains). These dimensions are required for compliance with ANSI Standard A117.0.
3. Installing back panel.
Ftn. w/MPW Mounting Plate: Refer to Fig. 24 for placement of braces onto back panel. Place the upper edge of the panel above hanger
bracket. Slide the panel down until it engages the hanger bracket. Be sure back panel is firmly engaged before releasing it.
Ftn. w/Wall Plate Assy.: Place the upper edge of the panel above mounting plate on the wall. Slide the panel down until it engages the hanger.
Be sure back panel is firmly engaged before releasing it.
4. Remove bottom access panel from fountain basin and save the screws.
Ftn. w/Back Panel: Install fountain to back panel and wall using (4) 5/16" x 2.00" long lag bolts and washers (NOT PROVIDED).
Ftn. w/MPW Mounting Plate: Install the fountain to the back panel and wall using (4) 5/16 “ x 6” long threaded rods, washers, and nuts
(provided). Tighten securely.
Ftn. w/Wall Plate Assy.: Install the fountain to the back panel and wall using (4) 5/16" x 3/4" long bolts and washers (provided) thru holes in
back panel. A washer is used on the bottom two (2) holes only. Tighten securely.
5. Assemble the operating cable to the fountain bracket. (Fountain should be mounted to exterior wall) Create a loop in the cable and thread the
free end of the cable through the wall into the freeze resistant box. The adjustment nuts should be in the middle of threaded area on the
operating cable. See Figure 18.
6. Connect free end of operating cable to the valve-operating bracket. The end of the cables must be recessed into the indents on the pivot
brackets. Remove cable free play by adjusting the jam nuts on the ends of the operating cable. See Figure 18.
7. Connect water line from fountain bubbler into freeze resistant box. The connection to the box uses a quick connect water fitting. Position the
water line, in the fountain, to drain back into interior mounted box. Any water left standing, in the exterior line, can freeze . See Fig. 21.
To insert tubing, push tube straight into fitting until it reaches a positive stop. To remove tubing from the fittings, relieve water pressure, push in
on dark gray collar while pulling out on the tubing. See Figure 2.
8. Connect drain and water supply lines to the freeze resistant fountain. Refer to Figure's 3 thru 16 for component positions.
Inline strainer must be used on the inlet water line. See Fig. 1.
Start-up
1. Turn on building water supply and check all connections for leaks. Repair as required.
2. Stream height is factory set at 35 PSI. If stream height needs to be changed adjust the regulator in the freeze resistant package. Clockwise
adjustment raises stream height, counter clockwise adjustment will lower stream.
3. Adjust operating cable as required. Cable system should have a minimal amount of free play to allow for proper valve operation. If the system is
too tight the valve will stay in the on position creating constant water flow. Too much free play will result in non-operation of the valve with the
push-buttons.
4. Note: Water from the drain back tube in the freeze resistant package, will continue to run while the valve is actuated.
5. After cable system is adjusted properly stuff flexible insulation into any openings between the outside wall and the interior box.
6. Recheck all connections. If all connections are leak free replace cover(s) on the freeze resistant box(es) and fountain(s).
FIG. 1
NOTE: WATER FLOW DIRECTION
SERVICE STOP
(NOT FURNISHED)
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 2
PAGE 3 97649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 3
HRFSBP - FR WITH WALL PLATE ASSY.
MOUNTING BOLT AND ACCESS HOLE LAYOUT
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 1/4" DIA. (6mm) HOLES FOR MOUNTING
PLATE TO WALL
PAGE 497649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
1. Wall should already be framed for the fountain using dimensions shown in Fig. 3. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom cover from fountain and save the screws.
3. Install the fountain using bolts and washers (not provided). Tighten securely.
4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide.
5. Install freeze-resistant box - see box instructions.
6. Replace bottom cover.
HRFSBP - FR WITH WALL PLATE ASSY.
ROUGH-IN DRAWINGS
FIG. 4
PAGE 5 97649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
HRFEBP - FR WITH WALL PLATE ASSY.
MOUNTING BOLT AND ACCESS HOLE LAYOUT
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 1/4" DIA. (6mm) HOLES FOR MOUNTING
PLATE TO WALL
FIG. 5
PAGE 697649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 6
HRFEBP - FR WITH WALL PLATE ASSY.
ROUGH-IN DRAWINGS
1. Wall should already be framed for the fountain using dimensions shown in Fig. 5. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom cover from fountain and save the screws.
3. Install the fountain using bolts and washers (not provided). Tighten securely.
4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide.
5. Install freeze-resistant box - see box instructions.
6. Replace bottom cover.
PAGE 7 97649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 7
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 3/8" DIA. (10mm) SLOTS FOR MOUNTING
HANGER BRACKET TO WALL
HRFEBP - FR WITH MPW101 MOUNTING PLATE
MOUNTING BOLT AND ACCESS HOLE LAYOUT
7 1/4"
184mm
12 1/8"
307mm
12"
305mm
MAX. WALL
THICKNESS
43 1/2"
1105mm
28 9/16"
725mm
30 1/4"
768mm
1 5/16"
33mm
1 7/8"
48mm
8"
203mm
16"
406mm
8"
203mm
3 1/8"
79mm
A
B
C
D
HANGER BRACKET
BACK PANEL
MPW101
MTG. PLT.
FINISHED FLOOR
PAGE 897649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 8
HRFEBP - FR WITH MPW101 MOUNNTING PLATE
ROUGH-IN DRAWINGS
1. Wall should already be framed for the fountains using dimensions shown in Fig. 7. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom covers from fountains and save the screws.
3. Install the fountains using bolts and washers (provided). Tighten securely.
4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.
5. Install freeze-resistant boxes - see box instructions.
6. Replace bottom covers.
13"
330mm
28 9/
725
m
27"
686mm
ADA
REQUIREMENT
6 1/2"
165mm
3 13/16"
97mm
12 1/8"
308mm
19 3/4"
502mm
20 3/8"
518mm
5/8"
16mm
18"
457mm
14"
355mm
17 1/2"
444mm
2 5/8"
66mm
3 5/8"
91mm
12"
305mm
MAX. WALL
THICKNESS
FINISHED FLOOR
FINISHED WALL
MPW101 MTG. PLT.
REF. SEPARATE
INSTALLATION
INSTRUCTIONS
FOR DETAILS
PAGE 9 97649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
HRFSEBP - FR WITH WALL PLATE ASSY.
MOUNTING BOLT AND ACCESS HOLE LAYOUT
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 1/4" DIA. (6mm) HOLES FOR MOUNTING
PLATE TO WALL
FIG. 9
PAGE 1097649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 10
HRFSEBP - FR WITH WALL PLATE ASSY.
ROUGH-IN DRAWINGS
1. Wall should already be framed for the fountains using dimensions shown in Fig. 9. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom covers from fountains and save the screws.
3. Install the fountains using bolts and washers (provided). Tighten securely.
4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.
5. Install freeze-resistant boxes - see box instructions.
6. Replace bottom covers.
PAGE 11 97649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
34 9/16"
878mm
43 1/2"
1105mm
36 1/4"
921mm
28 9/16"
725mm
30 1/4"
768mm
1 5/16"
33mm
1 5/16"
33mm
3 1/4"
82mm
16"
406mm
32"
813mm
6 5/8"
168mm
18 3/4"
476mm
MPW200
MTG. PLT.
BACK PANEL
HANGER BRACKET
A
A
B
B
C
C
D
FINISHED FLOOR
12"
305mm
MAX. WALL
THICKNESS
7 1/4"
184mm
7 1/4"
184mm
12 1/8"
307mm
12 1/8"
307mm
HRFSEBP - FR WITH MPW200 MOUNTING PLATE
MOUNTING BOLT AND ACCESS HOLE LAYOUT
FIG. 11
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 3/8" DIA. (10mm) SLOTS FOR MOUNTING
HANGER BRACKET TO WALL
PAGE 1297649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
HRFSEBP - FR WITH MPW200 MOUNTING PLATE
ROUGH-IN DRAWINGS
1. Wall should already be framed for the fountains using dimensions shown in Fig. 11. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom covers from fountains and save the screws.
3. Install the fountains using bolts and washers (provided). Tighten securely.
4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.
5. Install freeze-resistant boxes - see box instructions.
6. Replace bottom covers.
FIG. 12
3 13/16"
97mm
12 1/8"
308mm
6 5/8"
168mm
38 1/2"
978mm
12"
305mm
MAX. WALL
THICKNESS
2 5/8"
66mm
3 5/8"
91mm
28 9/16"
725mm
HRFEFR
34 9/16"
878mm
HRFSFR
27"
686mm
HRFEFR
ADA REQUIREMENT
6 1/2"
165mm
33"
838mm
HRFSFR
13"
330mm
HRFEFR
14"
355mm
HRFEFR
17 1/2"
444mm
HRFEFR
20"
508mm
HRFSFR
23 1/2"
597mm
HRFSFR
FINISHED WALL
5/8"
16mm
12 1/4"
311mm
HRFSFR
18"
457mm
HRFEFR
FINISHED FLOOR
MPW200 MTG. PLT.
REF. SEPARATE
INSTALLATION
INSTRUCTIONS
FOR DETAILS
PAGE 13 97649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
12 1/8"
308mm
12 1/8"
308mm
7 1/4"
184mm
7 1/4"
184mm
12"
305mm
MAX. WALL
THICKNESS
FINISHED FLOOR
26 13/16"
681mm
28 9/16"
725mm
30 1/4"
768mm
43 5/8"
1108mm
7 1/4"
184mm
BACK PANEL
3/8" DIA (20)
10mm
1 5/16"
33mm
18 3/4"
476mm
3 1/8"
80mm
3 1/8"
80mm
2 3/4"
70mm
1 5/16"
D
32 13/16"
833mm
34 9/16"
878mm
36 1/4"
921mm
7 1/4"
184mm
WALL PLATE
ASSEMBLY
B
A
C
16"
406mm
16"
406mm
5 1/4"
133mm
5 1/4"
133mm
8"
203mm
5 1/4"
133mm
5 1/4"
133mm
8"
203mm
HRFESBP - FR WITH WALL PLATE ASSY.
MOUNTING BOLT AND ACCESS HOLE LAYOUT
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 1/4" DIA. (6mm) HOLES FOR MOUNTING
PLATE TO WALL
FIG. 13
PAGE 1497649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
HRFESBP - FR WITH WALL PLATE ASSY
ROUGH-IN DRAWINGS
1. Wall should already be framed for the fountains using dimensions shown in Fig.13. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom covers from fountains and save the screws.
3. Install the fountains using bolts and washers (provided). Tighten securely.
4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.
5. Install freeze-resistant boxes - see box instructions.
6. Replace bottom covers.
FIG. 14
33"
838mm
HRFSFR
20 3/8"
518mm
27"
686mm
HRFEFR
ADA
REQUIREMENT
6 1/2"
165mm
38 1/2"
978mm
6 5/8"
168mm
12 1/8"
318mm
3 13/16"
97mm
FINISHED FLOOR
12 1/4"
311mm
HRFSFR
18"
457mm
HRFEFR
5/8"
16mm
12"
305mm
MAX. WALL
THICKNESS
2 5/8"
67mm
3 5/8"
92mm
13 1/8"
333mm
HRFEFR
14 3/16"
360mm
HRFEFR
17 11/16"
449mm
HRFEFR
19 1/8"
486mm
HRFSFR
20 3/16"
513mm
HRFSFR
23 11/16"
602mm
HRFSFR
28 9/16"
725mm
HRFEFR
34 9/16"
878mm
HRFSFR
PAGE 15 97649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
28 9/16"
725mm
30 1/4"
768mm
43 1/2"
1105mm
3 1/4"
82mm
16"
406mm
32"
813mm
6 5/8"
168mm
18 3/4"
476mm
1 5/16"
33mm
1 5/16"
33mm
34 9/16"
878mm
36 1/4"
921mm
FINISHED FLOOR
HANGER BRACKET
BACK PANEL
MPW200
MTG. PLT.
A
A
B
B
C
C
D
12"
305mm
MAX. WALL
THICKNESS
7 1/4"
184mm
12 1/8"
307mm
7 1/4"
184mm
12 1/8"
307mm
HRFESBP - FR WITH MPW200 MOUNTING PLATE
MOUNTING BOLT AND ACCESS HOLE LAYOUT
FIG. 15
LEGEND
A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER
SUPPLY TUBE
C = 7/8" DIA. (22mm) HOLE FOR OPERATING
CABLE
D = 3/8" DIA. (10mm) SLOTS FOR MOUNTING
HANGER BRACKET TO WALL
PAGE 1697649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
HRFESBP - FR WITH MPW200 MOUNTING PLATE
ROUGH-IN DRAWINGS
1. Wall should already be framed for the fountains using dimensions shown in Fig. 15. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom covers from fountains and save the screws.
3. Install the fountains using bolts and washers (provided). Tighten securely.
4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.
5. Install freeze-resistant boxes - see box instructions.
6. Replace bottom covers.
13"
330mm
HRFEFR
14"
355mm
HRFEFR
17 1/2"
444mm
HRFEFR
20"
508mm
HRFSFR
23 1/2"
597mm
HRFSFR
28 9/16"
725mm
HRFEFR
34 9/16"
878mm
HRFSFR
FINISHED FLOOR
FINISHED WALL
33"
838mm
HRFSFR
27"
686mm
HRFEFR
ADA REQUIREMENT
6 1/2"
165mm
3 13/16"
97mm
12 1/8"
308mm
6 5/8"
168mm
38 1/2"
978mm
20 3/8"
518mm
12"
305mm
MAX. WALL
THICKNESS
5/8"
16mm
12 1/4"
311mm
HRFSFR
18"
457mm
HRFEFR
2 5/8"
66mm
3 5/8"
91mm
MPW200 MTG. PLT.
REF. SEPARATE
INSTALLATION
INSTRUCTIONS
FOR DETAILS
FIG. 16
PAGE 17 97649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
FIG. 21
FIG. 19
FIG. 17
FIG. 18
See Fig. 19
See Fig. 17
FIG. 20
CABLE SHEATH ADJUSTMENT
To Increase Free Play
To Reduce Free Play
9
21
3
FIG. 22
PAGE 1897649C (Rev. P - 4/09)
HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR
56092C
112627543890
15009C
28823C
27945C
27946C
40045C
40206000
98118C
45662C
45663C
50198C
51667C
55919C
70425C
28782C
28783C
55000661
55000665
23187C
23189C
27043C
27261C
75672C
72000833
100322740560
28158C
28170C
28159C
28178C
56280C
28846C
28848C
28849C
27089C
27090C
PART NO.
ITEM NO.
PARTS LIST
POLY TUBING (CUT TO LENGTH)
SCREW - #10 - 24 X .50 PHTC
NIPPLE ASSY
BRACKET-REGULATOR MOUNTING
BRACKET-BASIN
BRACKET-BASIN PIVOT
HEX NUT 1-5/16
RETAINER
BUBBLER ASSEMBLY
PUSH BUTTON
SLEEVE-PUSH BUTTON GUIDE
SNAP BUSHING
BUMPER-REG. VALVE ASSY
PUSH BUTTON (EXTENSION)
PIVOT ROD
FOUNTAIN ARM - SHORT
FOUNTAIN ARM - LONG
BOTTOM COVER PLATE - SHORT
BOTTOM COVER PLATE - LONG
BACK PANEL - HRFSBP
BACK PANEL - HRFEBP
BACK PANEL - HRFSEBP
BACK PANEL - HRFESBP
CAP SCREW
WASTE ARM ASSY
WASHER
WALL PLATE ASSEMBLY - HRFSBP
WALL PLATE ASSEMBLY - HRFEBP
WALL PLATE ASSEMBLY - HRFSEBP
WALL PLATE ASSEMBLY - HRFESBP
EDGE TRIM
BACK PANEL ASSEMBLY-HRFEBP
BACK PANEL ASSEMBLY-HRFSEBP
BACK PANEL ASSEMBLY-HRFESBP
HANGER BRACKET-HRFEBP
HANGER BRACKET-HRFSEBP/ESBP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
NS
NS
DESCRIPTION
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
12
4
11, 19
10
14
8
15
13
5
7
6
12
16
FIG. 25
FIG. 23
SEE FIG. 22
22, 18
20
2, 17
SEE FIG. 25
1
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM
23
23
Installing Back Panel: When installing back panel
assy. (Item 24) with MPW (Mounting Plate), attach
channel braces as shown above. Remove the
protective backing from the tape installed on the
braces. Line up the corresponding holes in the
braces and back panel and press firmly in place.
FIG. 24
24
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR (2) Owner's manual

Halsey Taylor
Brand
Halsey Taylor
Model
HRF_EBP_SBP_SEBP_ESBP_FR (2)
Category
Sanitary ware
Type
Owner's manual

Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR (2) is a freeze-resistant fountain that is perfect for outdoor use in cold climates. The fountain is equipped with a Freeze Resistant Package (HTFRB1) that is installed on an interior heated wall. The interior space must maintain a minimum temperature of 50° F (10° C) to prevent the water in the fountain from freezing. The fountain is also equipped with an operating cable that allows the user to turn the water on and off from a distance. The fountain is easy to install and comes with all the necessary hardware.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents