Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR (2) Owner's manual

Brand: Halsey Taylor

Model: HRF_EBP_SBP_SEBP_ESBP_FR (2)

Category: Sanitary ware

Type: Owner's manual

Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR (2) is a freeze-resistant fountain that is perfect for outdoor use in cold climates. The fountain is equipped with a Freeze Resistant Package (HTFRB1) that is installed on an interior heated wall. The interior space must maintain a minimum temperature of 50° F (10° C) to prevent the water in the fountain from freezing. The fountain is also equipped with an operating cable that allows the user to turn the water on and off from a distance. The fountain is easy to install and comes with all the necessary hardware.

PAGE 1 97649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

Halsey Taylor Owners Manual

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

Freeze Resistant Fountains

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO

WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY

OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK

INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN

INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING

THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER

SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING

PLUMBING SYSTEM.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

HRFSBP - FR HRFSEBP - FR

To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE

INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLA-

TION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE

CODES. After installation, leave these instructions inside the fountain for future reference.

This Freeze Resistant Fountain is shipped in two separate cartons. The second carton(s)

contains the Freeze Resistant Package(s) HTFRB1 that are installed on an interior

heated wall. The interior space must maintain a minimum temperature of 50° F (10° C).

Refer to the Freeze Resistant Package for the rough-in dimensions for installation.

Installer

HRFEBP - FR HRFESBP - FR

PAGE 297649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

BUILDING WATER

INLET

1/4" O.D. TUBE

WATER INLET

3/8" O.D. UNPLATED

COPPER TUBE CONNECT

COLD WATER SUPPLY

TUBE IS

SECURED

IN POSITION

SIMPLY PUSH IN

TUBE TO ATTACH

PUSH IN COLLET

TO RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the interior heated area must be 50° F

(10° C) or higher. The freeze resistant package may be surface or recessed mounted. If recess mounted the surface of the cover must be flush

with the interior wall surface. The package is furnished with screws for mounting the cover to the box. If the box is recess mounted, do not

fasten the top and bottom of the cover to the box. Use the holes on the front only.

1. Fountains using the MPW Mounting Plate refer to Fig's. 7, 11, or 15 for hanger bracket location and rough-in dimensions.

NOTE: Review separate installation instructions for details of the MPW Mounting Plate.

Fountains using the Wall Plate Assy. refer to Fig's. 3, 5, 9, or 13 for rough-in dimensions.

2. Shown dimensions pertain to installation location (framing must support up to 150 lbs. weight for single fountain and 300 lbs. for dual

fountains). These dimensions are required for compliance with ANSI Standard A117.0.

3. Installing back panel.

Ftn. w/MPW Mounting Plate: Refer to Fig. 24 for placement of braces onto back panel. Place the upper edge of the panel above hanger

bracket. Slide the panel down until it engages the hanger bracket. Be sure back panel is firmly engaged before releasing it.

Ftn. w/Wall Plate Assy.: Place the upper edge of the panel above mounting plate on the wall. Slide the panel down until it engages the hanger.

Be sure back panel is firmly engaged before releasing it.

4. Remove bottom access panel from fountain basin and save the screws.

Ftn. w/Back Panel: Install fountain to back panel and wall using (4) 5/16" x 2.00" long lag bolts and washers (NOT PROVIDED).

Ftn. w/MPW Mounting Plate: Install the fountain to the back panel and wall using (4) 5/16 “ x 6” long threaded rods, washers, and nuts

(provided). Tighten securely.

Ftn. w/Wall Plate Assy.: Install the fountain to the back panel and wall using (4) 5/16" x 3/4" long bolts and washers (provided) thru holes in

back panel. A washer is used on the bottom two (2) holes only. Tighten securely.

5. Assemble the operating cable to the fountain bracket. (Fountain should be mounted to exterior wall) Create a loop in the cable and thread the

free end of the cable through the wall into the freeze resistant box. The adjustment nuts should be in the middle of threaded area on the

operating cable. See Figure 18.

6. Connect free end of operating cable to the valve-operating bracket. The end of the cables must be recessed into the indents on the pivot

brackets. Remove cable free play by adjusting the jam nuts on the ends of the operating cable. See Figure 18.

7. Connect water line from fountain bubbler into freeze resistant box. The connection to the box uses a quick connect water fitting. Position the

water line, in the fountain, to drain back into interior mounted box. Any water left standing, in the exterior line, can freeze . See Fig. 21.

To insert tubing, push tube straight into fitting until it reaches a positive stop. To remove tubing from the fittings, relieve water pressure, push in

on dark gray collar while pulling out on the tubing. See Figure 2.

8. Connect drain and water supply lines to the freeze resistant fountain. Refer to Figure's 3 thru 16 for component positions.

Inline strainer must be used on the inlet water line. See Fig. 1.

Start-up

1. Turn on building water supply and check all connections for leaks. Repair as required.

2. Stream height is factory set at 35 PSI. If stream height needs to be changed adjust the regulator in the freeze resistant package. Clockwise

adjustment raises stream height, counter clockwise adjustment will lower stream.

3. Adjust operating cable as required. Cable system should have a minimal amount of free play to allow for proper valve operation. If the system is

too tight the valve will stay in the on position creating constant water flow. Too much free play will result in non-operation of the valve with the

push-buttons.

4. Note: Water from the drain back tube in the freeze resistant package, will continue to run while the valve is actuated.

5. After cable system is adjusted properly stuff flexible insulation into any openings between the outside wall and the interior box.

6. Recheck all connections. If all connections are leak free replace cover(s) on the freeze resistant box(es) and fountain(s).

FIG. 1

NOTE: WATER FLOW DIRECTION

SERVICE STOP

(NOT FURNISHED)

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

FIG. 2

PAGE 3 97649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

FIG. 3

HRFSBP - FR WITH WALL PLATE ASSY.

MOUNTING BOLT AND ACCESS HOLE LAYOUT

LEGEND

A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE

B = 7/8" DIA. (22mm) HOLE FOR WATER

SUPPLY TUBE

C = 7/8" DIA. (22mm) HOLE FOR OPERATING

CABLE

D = 1/4" DIA. (6mm) HOLES FOR MOUNTING

PLATE TO WALL

PAGE 497649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

1. Wall should already be framed for the fountain using dimensions shown in Fig. 3. Shown dimensions pertain to installation location.

These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).

2. Remove bottom cover from fountain and save the screws.

3. Install the fountain using bolts and washers (not provided). Tighten securely.

4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide.

5. Install freeze-resistant box - see box instructions.

6. Replace bottom cover.

HRFSBP - FR WITH WALL PLATE ASSY.

ROUGH-IN DRAWINGS

FIG. 4

PAGE 5 97649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

HRFEBP - FR WITH WALL PLATE ASSY.

MOUNTING BOLT AND ACCESS HOLE LAYOUT

LEGEND

A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE

B = 7/8" DIA. (22mm) HOLE FOR WATER

SUPPLY TUBE

C = 7/8" DIA. (22mm) HOLE FOR OPERATING

CABLE

D = 1/4" DIA. (6mm) HOLES FOR MOUNTING

PLATE TO WALL

FIG. 5

PAGE 697649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

FIG. 6

HRFEBP - FR WITH WALL PLATE ASSY.

ROUGH-IN DRAWINGS

1. Wall should already be framed for the fountain using dimensions shown in Fig. 5. Shown dimensions pertain to installation location.

These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).

2. Remove bottom cover from fountain and save the screws.

3. Install the fountain using bolts and washers (not provided). Tighten securely.

4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide.

5. Install freeze-resistant box - see box instructions.

6. Replace bottom cover.

PAGE 7 97649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

FIG. 7

LEGEND

A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE

B = 7/8" DIA. (22mm) HOLE FOR WATER

SUPPLY TUBE

C = 7/8" DIA. (22mm) HOLE FOR OPERATING

CABLE

D = 3/8" DIA. (10mm) SLOTS FOR MOUNTING

HANGER BRACKET TO WALL

HRFEBP - FR WITH MPW101 MOUNTING PLATE

MOUNTING BOLT AND ACCESS HOLE LAYOUT

7 1/4"

184mm

12 1/8"

307mm

12"

305mm

MAX. WALL

THICKNESS

43 1/2"

1105mm

28 9/16"

725mm

30 1/4"

768mm

1 5/16"

33mm

1 7/8"

48mm

203mm

16"

406mm

203mm

3 1/8"

79mm

HANGER BRACKET

BACK PANEL

MPW101

MTG. PLT.

FINISHED FLOOR

PAGE 897649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

FIG. 8

HRFEBP - FR WITH MPW101 MOUNNTING PLATE

ROUGH-IN DRAWINGS

1. Wall should already be framed for the fountains using dimensions shown in Fig. 7. Shown dimensions pertain to installation location.

These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).

2. Remove bottom covers from fountains and save the screws.

3. Install the fountains using bolts and washers (provided). Tighten securely.

4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.

5. Install freeze-resistant boxes - see box instructions.

6. Replace bottom covers.

13"

330mm

28 9/

725

27"

686mm

ADA

REQUIREMENT

6 1/2"

165mm

3 13/16"

97mm

12 1/8"

308mm

19 3/4"

502mm

20 3/8"

518mm

5/8"

16mm

18"

457mm

14"

355mm

17 1/2"

444mm

2 5/8"

66mm

3 5/8"

91mm

12"

305mm

MAX. WALL

THICKNESS

FINISHED FLOOR

FINISHED WALL

MPW101 MTG. PLT.

REF. SEPARATE

INSTALLATION

INSTRUCTIONS

FOR DETAILS

PAGE 9 97649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

HRFSEBP - FR WITH WALL PLATE ASSY.

MOUNTING BOLT AND ACCESS HOLE LAYOUT

LEGEND

A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE

B = 7/8" DIA. (22mm) HOLE FOR WATER

SUPPLY TUBE

C = 7/8" DIA. (22mm) HOLE FOR OPERATING

CABLE

D = 1/4" DIA. (6mm) HOLES FOR MOUNTING

PLATE TO WALL

FIG. 9

PAGE 1097649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

FIG. 10

HRFSEBP - FR WITH WALL PLATE ASSY.

ROUGH-IN DRAWINGS

1. Wall should already be framed for the fountains using dimensions shown in Fig. 9. Shown dimensions pertain to installation location.

These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).

2. Remove bottom covers from fountains and save the screws.

3. Install the fountains using bolts and washers (provided). Tighten securely.

4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.

5. Install freeze-resistant boxes - see box instructions.

6. Replace bottom covers.

PAGE 11 97649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

34 9/16"

878mm

43 1/2"

1105mm

36 1/4"

921mm

28 9/16"

725mm

30 1/4"

768mm

1 5/16"

33mm

1 5/16"

33mm

3 1/4"

82mm

16"

406mm

32"

813mm

6 5/8"

168mm

18 3/4"

476mm

MPW200

MTG. PLT.

BACK PANEL

HANGER BRACKET

FINISHED FLOOR

12"

305mm

MAX. WALL

THICKNESS

7 1/4"

184mm

7 1/4"

184mm

12 1/8"

307mm

12 1/8"

307mm

HRFSEBP - FR WITH MPW200 MOUNTING PLATE

MOUNTING BOLT AND ACCESS HOLE LAYOUT

FIG. 11

LEGEND

A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE

B = 7/8" DIA. (22mm) HOLE FOR WATER

SUPPLY TUBE

C = 7/8" DIA. (22mm) HOLE FOR OPERATING

CABLE

D = 3/8" DIA. (10mm) SLOTS FOR MOUNTING

HANGER BRACKET TO WALL

PAGE 1297649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

HRFSEBP - FR WITH MPW200 MOUNTING PLATE

ROUGH-IN DRAWINGS

1. Wall should already be framed for the fountains using dimensions shown in Fig. 11. Shown dimensions pertain to installation location.

These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).

2. Remove bottom covers from fountains and save the screws.

3. Install the fountains using bolts and washers (provided). Tighten securely.

4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.

5. Install freeze-resistant boxes - see box instructions.

6. Replace bottom covers.

FIG. 12

3 13/16"

97mm

12 1/8"

308mm

6 5/8"

168mm

38 1/2"

978mm

12"

305mm

MAX. WALL

THICKNESS

2 5/8"

66mm

3 5/8"

91mm

28 9/16"

725mm

HRFEFR

34 9/16"

878mm

HRFSFR

27"

686mm

HRFEFR

ADA REQUIREMENT

6 1/2"

165mm

33"

838mm

HRFSFR

13"

330mm

HRFEFR

14"

355mm

HRFEFR

17 1/2"

444mm

HRFEFR

20"

508mm

HRFSFR

23 1/2"

597mm

HRFSFR

FINISHED WALL

5/8"

16mm

12 1/4"

311mm

HRFSFR

18"

457mm

HRFEFR

FINISHED FLOOR

MPW200 MTG. PLT.

REF. SEPARATE

INSTALLATION

INSTRUCTIONS

FOR DETAILS

PAGE 13 97649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

12 1/8"

308mm

12 1/8"

308mm

7 1/4"

184mm

7 1/4"

184mm

12"

305mm

MAX. WALL

THICKNESS

FINISHED FLOOR

26 13/16"

681mm

28 9/16"

725mm

30 1/4"

768mm

43 5/8"

1108mm

7 1/4"

184mm

BACK PANEL

3/8" DIA (20)

10mm

1 5/16"

33mm

18 3/4"

476mm

3 1/8"

80mm

3 1/8"

80mm

2 3/4"

70mm

1 5/16"

32 13/16"

833mm

34 9/16"

878mm

36 1/4"

921mm

7 1/4"

184mm

WALL PLATE

ASSEMBLY

16"

406mm

16"

406mm

5 1/4"

133mm

5 1/4"

133mm

203mm

5 1/4"

133mm

5 1/4"

133mm

203mm

HRFESBP - FR WITH WALL PLATE ASSY.

MOUNTING BOLT AND ACCESS HOLE LAYOUT

LEGEND

A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE

B = 7/8" DIA. (22mm) HOLE FOR WATER

SUPPLY TUBE

C = 7/8" DIA. (22mm) HOLE FOR OPERATING

CABLE

D = 1/4" DIA. (6mm) HOLES FOR MOUNTING

PLATE TO WALL

FIG. 13

PAGE 1497649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

HRFESBP - FR WITH WALL PLATE ASSY

ROUGH-IN DRAWINGS

1. Wall should already be framed for the fountains using dimensions shown in Fig.13. Shown dimensions pertain to installation location.

These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).

2. Remove bottom covers from fountains and save the screws.

3. Install the fountains using bolts and washers (provided). Tighten securely.

4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.

5. Install freeze-resistant boxes - see box instructions.

6. Replace bottom covers.

FIG. 14

33"

838mm

HRFSFR

20 3/8"

518mm

27"

686mm

HRFEFR

ADA

REQUIREMENT

6 1/2"

165mm

38 1/2"

978mm

6 5/8"

168mm

12 1/8"

318mm

3 13/16"

97mm

FINISHED FLOOR

12 1/4"

311mm

HRFSFR

18"

457mm

HRFEFR

5/8"

16mm

12"

305mm

MAX. WALL

THICKNESS

2 5/8"

67mm

3 5/8"

92mm

13 1/8"

333mm

HRFEFR

14 3/16"

360mm

HRFEFR

17 11/16"

449mm

HRFEFR

19 1/8"

486mm

HRFSFR

20 3/16"

513mm

HRFSFR

23 11/16"

602mm

HRFSFR

28 9/16"

725mm

HRFEFR

34 9/16"

878mm

HRFSFR

PAGE 15 97649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

28 9/16"

725mm

30 1/4"

768mm

43 1/2"

1105mm

3 1/4"

82mm

16"

406mm

32"

813mm

6 5/8"

168mm

18 3/4"

476mm

1 5/16"

33mm

1 5/16"

33mm

34 9/16"

878mm

36 1/4"

921mm

FINISHED FLOOR

HANGER BRACKET

BACK PANEL

MPW200

MTG. PLT.

12"

305mm

MAX. WALL

THICKNESS

7 1/4"

184mm

12 1/8"

307mm

7 1/4"

184mm

12 1/8"

307mm

HRFESBP - FR WITH MPW200 MOUNTING PLATE

MOUNTING BOLT AND ACCESS HOLE LAYOUT

FIG. 15

LEGEND

A = 1-3/4" DIA. (44mm) HOLE FOR WASTE LINE

B = 7/8" DIA. (22mm) HOLE FOR WATER

SUPPLY TUBE

C = 7/8" DIA. (22mm) HOLE FOR OPERATING

CABLE

D = 3/8" DIA. (10mm) SLOTS FOR MOUNTING

HANGER BRACKET TO WALL

PAGE 1697649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

HRFESBP - FR WITH MPW200 MOUNTING PLATE

ROUGH-IN DRAWINGS

1. Wall should already be framed for the fountains using dimensions shown in Fig. 15. Shown dimensions pertain to installation location.

These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).

2. Remove bottom covers from fountains and save the screws.

3. Install the fountains using bolts and washers (provided). Tighten securely.

4. Attach drain tubes to fountains and cut to required length using the freeze resistant boxes as guides.

5. Install freeze-resistant boxes - see box instructions.

6. Replace bottom covers.

13"

330mm

HRFEFR

14"

355mm

HRFEFR

17 1/2"

444mm

HRFEFR

20"

508mm

HRFSFR

23 1/2"

597mm

HRFSFR

28 9/16"

725mm

HRFEFR

34 9/16"

878mm

HRFSFR

FINISHED FLOOR

FINISHED WALL

33"

838mm

HRFSFR

27"

686mm

HRFEFR

ADA REQUIREMENT

6 1/2"

165mm

3 13/16"

97mm

12 1/8"

308mm

6 5/8"

168mm

38 1/2"

978mm

20 3/8"

518mm

12"

305mm

MAX. WALL

THICKNESS

5/8"

16mm

12 1/4"

311mm

HRFSFR

18"

457mm

HRFEFR

2 5/8"

66mm

3 5/8"

91mm

MPW200 MTG. PLT.

REF. SEPARATE

INSTALLATION

INSTRUCTIONS

FOR DETAILS

FIG. 16

PAGE 17 97649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

FIG. 21

FIG. 19

FIG. 17

FIG. 18

See Fig. 19

See Fig. 17

FIG. 20

CABLE SHEATH ADJUSTMENT

To Increase Free Play

To Reduce Free Play

FIG. 22

PAGE 1897649C (Rev. P - 4/09)

HRFSBP - FR HRFEBP - FR HRFSEBP - FR HRFESBP - FR

56092C

112627543890

15009C

28823C

27945C

27946C

40045C

40206000

98118C

45662C

45663C

50198C

51667C

55919C

70425C

28782C

28783C

55000661

55000665

23187C

23189C

27043C

27261C

75672C

72000833

100322740560

28158C

28170C

28159C

28178C

56280C

28846C

28848C

28849C

27089C

27090C

PART NO.

ITEM NO.

PARTS LIST

POLY TUBING (CUT TO LENGTH)

SCREW - #10 - 24 X .50 PHTC

NIPPLE ASSY

BRACKET-REGULATOR MOUNTING

BRACKET-BASIN

BRACKET-BASIN PIVOT

HEX NUT 1-5/16

RETAINER

BUBBLER ASSEMBLY

PUSH BUTTON

SLEEVE-PUSH BUTTON GUIDE

SNAP BUSHING

BUMPER-REG. VALVE ASSY

PUSH BUTTON (EXTENSION)

PIVOT ROD

FOUNTAIN ARM - SHORT

FOUNTAIN ARM - LONG

BOTTOM COVER PLATE - SHORT

BOTTOM COVER PLATE - LONG

BACK PANEL - HRFSBP

BACK PANEL - HRFEBP

BACK PANEL - HRFSEBP

BACK PANEL - HRFESBP

CAP SCREW

WASTE ARM ASSY

WASHER

WALL PLATE ASSEMBLY - HRFSBP

WALL PLATE ASSEMBLY - HRFEBP

WALL PLATE ASSEMBLY - HRFSEBP

WALL PLATE ASSEMBLY - HRFESBP

EDGE TRIM

BACK PANEL ASSEMBLY-HRFEBP

BACK PANEL ASSEMBLY-HRFSEBP

BACK PANEL ASSEMBLY-HRFESBP

HANGER BRACKET-HRFEBP

HANGER BRACKET-HRFSEBP/ESBP

DESCRIPTION

2222 CAMDEN COURT

OAK BROOK, IL 60523

630.574.3500

PRINTED IN U.S.A.

11, 19

FIG. 25

FIG. 23

SEE FIG. 22

22, 18

2, 17

SEE FIG. 25

FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM

Installing Back Panel: When installing back panel

assy. (Item 24) with MPW (Mounting Plate), attach

channel braces as shown above. Remove the

protective backing from the tape installed on the

braces. Line up the corresponding holes in the

braces and back panel and press firmly in place.

FIG. 24

Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR (2) Owner's manual

Brand: Halsey Taylor

Model: HRF_EBP_SBP_SEBP_ESBP_FR (2)

Category: Sanitary ware

Type: Owner's manual

Download PDF

report

Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR (2) Owner's manual

Halsey Taylor HRF_EBP_SBP_SEBP_ESBP_FR (2) Owner's manual

Related papers

Other documents