Parkside PMFS 200 B2 Translation Of The Original Instructions

3-IN-1 MULTI-PURPOSE SANDER PMFS 200 B2

3-IN-1 MULTI-PURPOSE SANDER

Translation of the original instructions

3-IN-1-MUL TIFUNKTIONSSCHLEIFER

Originalbetriebsanleitung

IAN 275401

275401_par_Multifunktionsschleifer_cover_GB_IE_NI.indd 2 22.09.16 12:31

GB / IE / NI Translation of the original instructions

Page 4

DE / AT / CH Originalbetriebsanleitung

Seite 19

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

275401_par_Multifunktionsschleifer_cover_GB_IE_NI.indd 3 22.09.16 12:31

Page is loading ...

GB

4

IE NI

Content

Introduction .................................4

Intended Use ................................4

General Description ......................5

Scope of delivery .............................. 5

Overview ......................................... 5

Technical Data .............................. 6

Notes on Safety ...........................6

Symbols ........................................... 6

General safety instructions for power

tools ................................................ 7

Additional safety instructions .............. 9

Residual risks .................................. 10

Assembly ...................................10

Installing/changing the sanding disc .. 10

Attaching/removing sanding sheet .... 11

Connecting/removing/emptying the

dust collection box .......................... 12

Connecting/removing external dust

extraction ....................................... 12

Operation ..................................12

Switching on/off ............................. 12

Adjusting the oscillation rate ............. 12

Practical tips ..............................13

Sanding ......................................... 13

Selection of sanding sheet ................ 13

Choosing the right sanding disc ........ 13

Cleaning/Maintenance ...............14

Cleaning ........................................ 14

Cleaning/replacing the lter insert

of the dust collection box ................ 14

Storage ......................................14

Waste disposal and environmental

protection ..................................14

Spare Parts/Accessories ............. 15

Guarantee .................................16

Repair Service ............................17

Service-Center ............................17

Importer .................................... 17

Trouble Shooting ........................18

Translation of the original EC

declaration of conformity ............ 35

Exploded Drawing ...................... 37

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product. During production,

this equipment has been checked for qual-

ity and subjected to a nal inspection. The

functionality of your equipment is therefore

guaranteed.

The operating instructions constitute

part of this product. They contain

important information on safety, use

and disposal.

Before using the product, familiarise

yourself with all of the operating

and safety instructions. Use the

product only as described and for

the applications specied. Keep this

manual safely and in the event that

the product is passed on, hand over

all documents to the third party.

Intended Use

The 3-in-1 multi-purpose sander is intended

for dry sanding of wood, metal, plastic,

plaster and painted surfaces.

The device is exible and suitable for sur-

face grinding and for grinding of edges,

corners and hard to reach places.

The device is not suitable for commercial

use.

The equipment is designed for use by

adults. Adolescents over the age of 16

may use the device only under supervision.

The manufacturer is not liable for damages

caused by unspecied use or incorrect op-

eration.

Any other use that is not explicitly ap-

proved in these instructions may result in

damage to the equipment and represent a

serious danger to the user.

GB

5

IE NI

General Description

The illustration of the principal

functioning parts can be found

on the front and back foldout

pages.

Scope of delivery

Carefully unpack the trimmer and check

that it is complete. Dispose of the packag-

ing material correctly.

• Sander motor unit

• Hand sander disc

• Eccentric grinder disc

• Orbital sander disc

• Sanding sheets

(grain size P80 / P240)

- 2x for hand sander disc

- 2x for eccentric grinder disc

- 2x for orbital sander disc

• Dust collection box

• Adapter for external dust extraction

• 4 replacement Phillips screws

• 4 replacement rubber pins

• Case

• Instruction Manual

Overview

1 Oscillation frequency controller

2 Ventilation holes

3 On/off switch

4 Handle

5 Mains cable

6 Connection for dust extraction

7 Release button dust collection

box

8 Dust collection box lid

9 Tab for opening the dust collec-

tion box

10 Dust collection box

11 Adapter for external dust extrac-

tion

12 Orbital sander disc

13 Terminal strip for clamping sand-

paper

14 Clamping lever for clamping

sandpaper

15 Sander motor unit

16 Case

17 Eccentric grinder disc

18 Hand sander disc

19 2 sanding sheets for orbital

sander disc

20 2 sanding sheets for eccentric

grinder disc

21 2 sanding sheets for hand sand-

er disc

22 4 Phillips screws for mounting

the sanding disc

23 Movable mounting plate

24 Threaded bore

25 Marking

26 Felt ring

27 4 rubber pins

28 Mounting frame for lter insert

29 Filter insert for dust collection

box

GB

6

IE NI

Technical Data

3-in-1 multi-purpose sander

..... PMFS 200 B2

Rated input voltage (U) ......230 V~, 50 Hz

Power input (P) .............................200 W

Idling speed (n

0

) ...........7000-12000 min

-1

Oscillation rate (n) ......14000-24000 min

-1

Weight (without sander disc and

dust collection box) .....................1.38 kg

Protection class .................................

II

Protection category ........................... IP20

Sound pressure level

(L

pA

) ......................79 dB(A); K

pA

= 3 dB

Sound power level

(L

WA

) ....................90 dB(A); K

WA

= 3 dB

Vibration

(a

h

) ................ 13.4 m/s

2

;

K

h

= 1.5 m/s

2

Technical and optical changes may be

undertaken in the course of further develop-

ment without notice. All dimensions, refer-

ences and information in this instruction

manual are therefore not guaranteed. Legal

claims made on the basis of the instruction

manual can therefore not be considered as

valid.

The stated vibration emission value was

measured in accordance with a standard

testing procedure and may be used to com-

pare one power tool to another.

The stated vibration emission value may

also be used for a preliminary exposure

assessment.

Warning: The vibration emission

value may differ during actual use of

the power tool from the stated value

depending on the manner in which

the power tool is used.

Safety precautions aimed at protect-

ing the user should be based on esti-

mated exposure under actual usage

conditions (all parts of the operating

cycle are to be considered, includ-

ing, for example, times during which

the power tool is turned off and

times when the tool is turned on but

is running idle).

Notes on Safety

This section details the basic safety instruc-

tions for working with the appliance.

Symbols

Symbols in the manual:

Warning symbols with infor-

mation on damage and injury

prevention.

Instruction symbols (the instruction

is explained at the place of the ex-

clamation mark) with information on

preventing damage.

Help symbols with information on

improving tool handling.

GB

7

IE NI

Symbols on the Equipment:

Warning!

Risk of electric shock!

Disconnect from the mains before

carrying out maintenance and re-

pair work.

Injury hazard caused by rotating

tool! Keep hands away.

Read through the instruction manual

carefully.

Wear ear protection.

Wear eye protection.

Wear breathing protection.

Wear hand protection.

Protection class II

Electrical appliances must not be

disposed of with the domestic

waste.

General safety instructions

for power tools

WARNING! Read all safety

directions and instructions.

Omissions in the compliance with

safety directions and instructions

can cause electrical shock, re

and/or severe injuries.

Retain all safety directions and in-

structions for future use.

The term „power tool“ in the warnings re-

fers to your mains-operated (corded) power

tool or battery-operated (cordless) power

tool.

1) WORK AREA SAFETY

• Keep work area clean and well

lit. Cluttered or dark areas invite ac-

cidents.

• Do not operate power tools in

explosive atmospheres, such as

in the presence of ammable

Iiquids, gases or dust. Power tools

create sparks which may ignite the dust

or fumes.

• Keep children and bystanders

away while operating a power

tool. Distractions can cause you to

lose control.

2) ELECTRICAL SAFETY

• Power tool plugs must match

the outlet. Never modify the

plug in any way. Do not use

any adapter plugs with earthed

(grounded) power tools. Unmodi-

ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed

or grounded surfaces, such as

GB

8

IE NI

pipes, radiators, ranges and re-

frigerators. There is an increased risk

of electric shock if your body is earthed

or grounded.

• Do not expose power tools to

rain or wet conditions. Water

entering a power tool will increase the

risk of electric shock.

• Do not abuse the cord. Never

use the cord for carrying, pull-

ing or unplugging the power

tool. Keep cord away from

heat, oil, sharp edges or moving

parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use of a

cord suitable for outdoor use reduces

the risk of electric shock.

• If operating a power tool in a

damp location is unavoidable,

use a residual current device

(RCD) protected supply. Use of an

RCD reduces the risk of electric shock.

3) PERSONAL SAFETY

• Stay alert, watch what you are

doing and use common sense

when operating a power tool.

Do not use a power tool while

you are tired or under the inu-

ence of drugs, alcohol or medi-

cation. A moment of inattention white

operating power tools may result in

serious personal injury.

• Use personal protective equip-

ment. Always wear eye protec-

tion. Protective equipment such as dust

mask, non-skid safety shoes, hard hat,

or hearing protection used for appro-

priate conditions will reduce personal

injuries.

• Prevent unintentional starting.

Ensure the switch is in the off-

position before connecting to

power source and/or battery

pack, picking up or carrying the

tool. Carrying power tools with your

nger on the switch or energising pow-

er tools that have the switch on invites

accidents.

• Remove any adjusting key or

wrench before turning the pow-

er tool on. A wrench or a key left

attached to a rotating part of the power

tool may result in personal injury.

• Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the power

tool in unexpected situations.

• Dress properly. Do not wear

loose clothing or jewellery. Keep

your hair, clothing and gloves away

from moving parts. Loose clothes, jew-

ellery or long hair can be caught in

moving parts.

• If devices are provided for the

connection of dust extraction

and collection facilities, ensure

these are connected and prop-

erly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

• Do not force the power tool. Use

the correct power tool for your

application. The correct power tool

will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the

switch does not turn it on and

off. Any power tool that cannot be

controlled with the switch is dangerous

and must be repaired.

• Disconnect the plug from the

GB

9

IE NI

power source and/or the bat-

tery pack from the power tool

before making any adjust

-ments, changing accessories, or

storing power tools. Such preven-

tive safety measures reduce the risk of

starting the power tool accidentaIly.

• Store idle power tools out of the

reach of children and do not al-

low persons unfamiliar with the

power tool or these instructions

to operate the power tool. Power

tools are dangerous in the hands of

untrained users.

• Maintain power tools. Check

for misalignment or binding of

moving parts, breakage of parts

and any other condition that

may affect the power tool’s op-

eration. If damaged, have the power

tool repaired before use. Many acci-

dents are caused by poorly maintained

power tools.

• Keep cutting tools sharp and

clean. Properly maintained cutting

tools with sharp cutting edges are less

Iikely to bind and are easier to control.

• Use the power tool, accessories

and tool bits etc. in accordance

with these instructions, tak-

ing into account the working

conditions and the work to be

performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

• Hold the device by the insu-

lated gripping surfaces when

performing work in which the

cutting tool may come into con-

tact with hidden wiring or its

own cord. Contact with a live wire

can also cause a charge in metal parts

of the device and result in an electric

shock.

5) SERVICE

• Have your power tool serviced

by a qualied repair person us-

ing only identical replacement

parts. This will ensure that the safety of

the power tool is maintained.

Additional safety instructions

Warning! Sawing or sanding

can result in the formation of

hazardous dusts (e.g. arising

from materials with paints con-

taining lead, materials contain-

ing asbestos, metals or some

wood types) which can present

a hazard to the operator or

persons in the vicinity. Make

sure that the workplace is well

ventilated. Always wear safety

goggles, safety gloves and

respiratory protection. Attach a

dust extraction system.

1) SPECIAL SAFETY INFORMATION

FOR THE CORDLESS COMBINA-

TION TOOL

• Secure the workpiece. A work-

piece that is retained with clamping ap-

pliances or a vice is held more securely

than with your hand.

• Only use the power tool for dry

sanding. Do not scrape moist

materials. Penetration of water into

the power tool increases the risk of elec-

tric shock.

• Avoid overheating the sanded

object and the sander itself. Pos-

sible re hazard.

• The workpiece gets hot dur-

ing grinding. Do not touch the

machined area, allow it to cool

GB

10

IE NI

down. There is a risk of burning. Do

not use coolants or the like.

• Always empty the dust con-

tainer before work breaks.

Sanding dust in the dust sack, micro

lter, paper sack (or in the lter sack or

extraction system lter) can self-ignite

under unfavourable conditions such

as ying sparks caused by grinding

metals. Particular hazards are caused

if the sanding dust is mixed with paint,

polyurethane residues or other chemi-

cal substances, or if the sanded object

is hot after long working periods.

Please check the operating manual of

your vacuum cleaner whether it is suit-

able for the suction of grinding chips.

• Connect the appliance to a power

socket with a residual current circuit

breaker of rated residual current no

more than 30 mA.

• If the supply cord of this power

tool is damaged, it must be re-

placed by a specially prepared

cord available through the ser-

vice organization.

Residual risks

Even if properly operating and handling

this electric tool, some residual risks will

remain. Due to its construction and build,

this electric tool may present the following

hazards:

a) Lung damage, if suitable respiratory

protection is not worn;

b) Cuts

c) Ear damage if working without ear pro-

tection.

d) Eye damage if suitable eye protection

is not worn.

e) Damage to your health caused by

swinging your hands and arms when

operating the appliance for longer pe-

riods of time or if the unit is not held or

maintained properly.

Warning! During operation, this

electric tool generates an electro-

magnetic eld which, under certain

circumstances, may impair the

functionality of active or passive

medical implants. To reduce the risk

of serious or lethal injuries, we re-

commend that persons with medical

implants consult their doctor and the

manufacturer of their medical im-

plant before operating the machine.

Assembly

Always disconnect the plug from

the mains socket before working.

Danger of electric shock.

Installing/changing the

sanding disc

The device is delivered with the orbital

sander disc pre-installed.

Removing pre-assembled

sanding disc:

1. Remove the 4 Phillips screws

(22).

2. Remove the pre-assembled sand-

ing disc.

Position the mounting

plate:

3. Position the movable mounting

plate (23) on the device:

The two threaded bores (24)

of the mounting plate must be

aligned with the markings (25)

on the device.

4. Check the correct position of the

felt ring (26).

GB

11

IE NI

Installing the eccentric

grinder disc:

5. Place the desired eccentric

grinder disc (17) on the mount-

ing plate (23).

6. Fasten the sanding disc with the

4 Phillips screws (22).

7. Make sure that the sanding disc

is rmly in place.

Installing the orbital sand-

er disc and hand sander

disc:

5. Insert the 4 rubber pins (27) with

the latching nose (27a) into the

4 recesses in the sanding disc

(18/

12).

6. Place the desired sanding disc

(18/

12) on the mounting

plate (23).

The rubber pins (27) t into the

recesses of the device. Only one

position is possible.

7. Fasten the sanding disc with the

4 Phillips screws (22).

8. Make sure that the sanding disc

is rmly in place.

Attaching/removing sanding

sheet

Clean the sanding disc before you

attach a sanding sheet.

When using sanding sheets without

ventilation holes, dust extraction is

not possible.

Use only appropriate sanding sheet

sizes. Sanding sheets, which ex-

tend beyond the sanding disc, can

cause injuries and can cause the

sanding sheets to block or tear.

Sanding sheet with Velcro

The sanding discs are tted with Velcro

backing for quick mounting of sanding

sheets.

Attaching sanding sheet:

1. Press the desired sanding sheet

(19/

20/ 21) evenly onto

the sanding disc (12/

17/

18). Ensure that the ventilation

holes in the sanding sheet are

placed directly above the extrac-

tion openings in the sanding disc.

Removing sanding sheet:

2. Simply pull the sanding sheet

(19/

20/ 21) off the sand-

ing disc (12/

17/ 18).

Sanding sheet without Velcro

The orbital sander disc (12) is equipped

with terminal strips (13) for clamping sand-

ing sheets without Velcro (sanding sheets

not included).

Clamping sanding sheet:

1. Open the two clamping levers

(14) on the orbital sander disc

(12).

2. Slide one end of the sanding

sheet under the terminal strip (13).

3. Clamp the sanding sheet by lock-

ing the clamping lever (14).

4. Pull the sanding sheet tightly

over the orbital sander disc (12).

Clamp the other end of the sand-

ing sheet.

Removing sanding sheet:

5. Open the two clamping levers

(14) and pull out the sanding

sheet.

GB

12

IE NI

Connecting/removing/emp-

tying the dust collection box

Connecting the dust collec-

tion box:

1. Before connecting, ensure that

the dust collection box (10) is

rmly closed.

2. Slide the dust collection box (10)

all the way onto the connection

for dust extraction (6). The two

lugs (6a) on the connection for

dust extraction (6) t into the two

grooves (10a) of the dust collec-

tion box (10).

Removing the dust collec-

tion box:

3. Press the release button (7) and

pull the dust collection box (10)

out.

Emptying the dust collec-

tion box:

4. Pull the tab (9) and remove the

dust collection box lid (8).

5. To empty, simply shake or knock

out the dust collection box (10).

6. Then close the dust collection

box (10) again.

Empty the dust collection box regu-

larly to ensure optimal suction.

Connecting/removing exter-

nal dust extraction

Connecting external dust

extraction:

1. Slide the adapter for external

dust extraction (11) all the way

onto the connection for dust ex-

traction (6).

2. Connect the suction tube of a

vacuum cleaner (not included)

to the adapter for external dust

extraction (11).

Removing external dust

extraction

3. Disconnect the suction tube from

the adapter for external dust ex-

traction (11).

4. Disconnect the adapter for exter-

nal dust extraction (11).

Operation

Switching on/off

Make sure that the power supply

voltage matches the voltage rat-

ing indicated on the device‘s type

plate.

Connect the machine to the power

supply.

1. To switch on, push the on/off

switch (3) to position „I“. The

tool will power on.

2. To switch off, push the on/off

switch (3) to position „O“. The

tool will power off.

Adjusting the oscillation rate

The required oscillation rate depends on

the material to be processed and can be

determined through practical testing.

In order to regulate the oscillation

rate, use the oscillation frequency

controller (1):

1 lowest oscillation rate

MAX

maximum oscillation rate.

GB

13

IE NI

Practical tips

When working with the ap-

pliance, always wear suita-

ble clothing and appropriate

protective equipment.

Prior to each use it must be

ensured that the appliance is

working correctly.

Personal protective equip-

ment and a fully functional

appliance reduce the risk of

injuries and accidents.

Always disconnect the plug from

the mains socket before working.

Danger of electric shock.

Sanding

• Move the appliance against the work-

piece once it is switched on.

• After machining, lift the sanding disc

up before turning off the device.

• Always lead the mains cable towards

the back and away from the device.

• Clean the sanding plate before you at-

tach a sanding sheet.

• Only work with sanding sheets in per-

fect condition to achieve good sanding

results.

• Work with low and even pressure and

even forward pressure. This protects

the appliance and the sanding sheet.

• Grind rough corners and edges with

the top or side edge of the sanding

sheet.

• Do not use the same sanding sheet to

sand different materials (e.g. metal

and then wood).

• Empty the dust collection box or the

vacuum cleaner regularly in order to

ensure optimal suction.

Selection of sanding sheet

When using sanding sheets without

ventilation holes, dust extraction is

not possible.

Grain size P Application

P60

for pre-sanding rough

wood surfaces

P80

P120

for plain sanding

P240

for ne sanding of primed

and painted surfaces

Choosing the right sanding

disc

Orbital sander disc:

• For sanding/grinding large surfaces

as well as corners, edges and outer

curves.

Hand sander disc:

• For processing surface areas, edges,

corners and hard to reach places.

Eccentric grinder disc:

• For ne grinding of surfaces and pro-

cessing of inner curves.

GB

14

IE NI

Cleaning/Maintenance

Pull the mains plug before any ad-

justments, maintenance or repair.

Repair and servicing work not

described in this manual should

always be carried by our Service

Centre. Use only original parts.

The following cleaning and servicing

should be done regularly. This will ensure a

long and reliable service life.

Cleaning

Do not spray the appliance

with water and do not im-

merse it in water. Electric

shock hazard!

• Keep clean the ventilation slots, motor

housing and handles of the appliance.

Use a damp cloth or a brush.

Do not use cleaning agents or solvents.

You may otherwise irreparably damage

the appliance.

• Clean the sanding sheet with a vacuum

cleaner or knock it out.

Cleaning/replacing the lter

insert of the dust collection

box

Check the lter insert once or twice a year

for contamination.

Removing the lter insert:

1. Pull the tab (9) and remove the

dust collection box lid (8) (see

“Connecting/removing/empty-

ing the dust collection box”).

2. Pull the mounting frame (28) from

the dust collection box lid (8) and

remove the lter insert (29).

3. Wash the lter insert (29) with

warm water and soap and let it

dry.

Replace a heavily contaminated

or damaged lter insert (see

“Spare Parts/Accessories”).

Installing the lter insert:

4. Replace the lter insert (29) and

the mounting frame (28) in the

dust collection box lid (8).

5. Then close the dust collection

box (10).

Storage

• Store the device in a dry place well out

of reach of children.

• Empty the dust collection box before

storing the device (see “Connecting/

removing/emptying the dust collection

box”).

Waste disposal and

environmental protection

Be environmentally friendly. Return the

tool, accessories and packaging to a recy-

cling centre when you have nished with

them.

Machines are not to be place with

domestic waste.

• Hand over the device at an utilization

location. The plastic and metal parts

employed can be separated out into

pure materials and recycling can be

implemented. Ask your Service Center

about this.

• Defective units returned to us will be

disposed of for free.

GB

15

IE NI

Spare Parts/Accessories

Spare parts and accessories can be obtained at

www.grizzly-service.eu

If you do not have internet access, please contact the Service Centre via telephone (see

“Service-Center” Page 17). Please have the order number mentioned below ready.

Position Position Description Order No.

instruction exploded

manual drawing

8/10/11 32-36 Dust collection box 91104513

12 10-16 Orbital sander disc 91104512

17 41 Eccentric grinder disc 91104516

18 40/42 Hand sander disc 91104515

19 2 sanding sheets for orbital sander disc

(grain size P80 / P240) 30211084

20 2 sanding sheets for eccentric grinder disc

(grain size P80 / P240) 30211083

21 2 sanding sheets for hand sander disc

(grain size P80 / P240) 30211082

26 39 Felt ring 91104514

27 4 rubber pins 91104518

29 33 Filter insert 91104517

2 Fan wheel 91104511

GB

16

IE NI

Guarantee

Dear Customer,

This equipment is provided with a 3-year

guarantee from the date of purchase.

In case of defects, you have statutory rights

against the seller of the product. These

statutory rights are not restricted by our

guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the

date of purchase. Please retain the original

receipt. This document is required as proof

of purchase.

If a material or manufacturing defect occurs

within three years of the date of purchase

of this product, we will repair or replace –

at our choice – the product for you free of

charge. This guarantee requires the defec-

tive equipment and proof of purchase to be

presented within the three-year period with

a brief written description of what consti-

tutes the defect and when it occurred.

If the defect is covered by our guarantee,

you will receive either the repaired product

or a new product. No new guarantee pe-

riod begins on repair or replacement of the

product.

Guarantee Period and Statutory

Claims for Defects

The guarantee period is not extended by

the guarantee service. This also applies for

replaced or repaired parts. Any damages

and defects already present at the time of

purchase must be reported immediately af-

ter unpacking. Repairs arising after expiry

of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully produced

in accordance with strict quality guidelines

and conscientiously checked prior to delivery.

The guarantee applies for all material and

manufacturing defects. This guarantee does

not extend to cover product parts that are

subject to normal wear and may therefore

be considered as wearing parts (e.g. tools,

sanding sheets) or to cover damage to

breakable parts (e.g. switches).

This guarantee shall be invalid if the prod-

uct has been damaged, used incorrectly or

not maintained. Precise adherence to all of

the instructions specied in the operating

manual is required for proper use of the

product. Intended uses and actions against

which the operating manual advises or

warns must be categorically avoided.

The product is designed only for private

and not commercial use. The guarantee

will be invalidated in case of misuse or

improper handling, use of force, or inter-

ventions not undertaken by our authorised

service branch.

Processing in Case of Guarantee

To ensure quick handling of you issue,

please follow the following directions:

• Please have the receipt and identica-

tion number (IAN 275401) ready as

proof of purchase for all enquiries.

• Please nd the item number on the rat-

ing plate.

• Should functional errors or other de-

fects occur, please initially contact the

service department specied below by

telephone or by e-mail. You will then

receive further information on the pro-

cessing of your complaint.

• After consultation with our customer ser-

vice, a product recorded as defective

can be sent postage paid to the service

address communicated to you, with the

proof of purchase (receipt) and speci-

cation of what constitutes the defect

and when it occurred. In order to avoid

GB

17

IE NI

Service-Center

GB

Service Great Britain

Tel.: 0871 5000 720

(£ 0.10/Min.)

E-Mail: [email protected]

IAN 275401

IE

Service Ireland

NI

Service Northern Ireland

Tel.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (off peak))

E-Mail: [email protected]

IAN 275401

Importer

Please note that the following address is not

a service address. Please initially contact

the service centre specied above.

Grizzly Tools GmbH & Co. KG

Stockstädter Straße 20

63762 Großostheim, Germany

www.grizzly-service.eu

acceptance problems and additional

costs, please be sure to use only the ad-

dress communicated to you. Ensure that

the consignment is not sent carriage

forward or by bulky goods, express or

other special freight. Please send the

equipment inc. all accessories supplied

at the time of purchase and ensure ad-

equate, safe transport packaging.

Repair Service

For a charge, repairs not covered by the

guarantee can be carried out by our ser-

vice branch, which will be happy to issue

a cost estimate for you. We can handle

only equipment that has been sent with ad-

equate packaging and postage.

Attention: Please send your equipment to

our service branch in clean condition and

with an indication of the defect.

Equipment sent carriage forward or by

bulky goods, express or other special

freight will not be accepted.

We will dispose of your defective devices

free of charge when you send them to us.

GB

18

IE NI

Trouble Shooting

Problem Possible Cause Error correction

Device doesn‘t start

Mains voltage missing

Main circuit breaker is

tripped

Check the socket, mains cable, line,

mains plug, repairs to be carried

out by qualied electrician if neces-

sary, check main circuit breaker.

On/off switch (

3) may

be defective

Repair by Customer Care

Engine faulty

Device works with

interruptions

Internal loose contact

Repair by Customer Care

On/off switch (

3) is

broken

Sanding disc does

not move although

the motor is running

Sanding disc (

12/17/18) is not correctly

assembled

Install sanding disc correctly (see

„Assembly“)

Engine is slowing

down and stops

Device is overloaded

through workpiece

Reduce pressure on grinding tool

Workpiece unsuitable

Poor grinding

performance

Sanding sheet or sanding

disc (

17/12/18) un-

suitable for the workpiece

to be processed

Use a suitable sanding sheet or

sanding disc (see “Assembly”)

Worn sanding sheet

Insert a new sanding sheet

(see “Assembly”)

Incorrect speed Adjust the oscillation rate

Sanding sheet wears

down quickly

Sanding sheet unsuitable

for the workpiece to be

processed

Use a suitable sanding sheet

(see “Assembly”)

Too much pressure applied Reduce the pressure

Speed too high

Adjust the oscillation rate

(see “Operation”)

Page is loading ...

35

Translation of the original

EC declaration of conformity

We hereby conrm that the

3-in-1 multi-purpose sander

model PMFS 200 B2

Serial number 201608000001 - 201608116524

conforms with the following applicable relevant version of the EU guidelines:

2006/42/EC • 2014/30/EU • 2011/65/EU*

In order to guarantee consistency, the following harmonised standards as well as

national standards and stipulations have been applied:

EN 60745-1/A11:2010 • EN 60745-2-4/A11:2011 • EN 62233:2008

EN 55014-1/A2:2011 • EN 55014-2/A2:2008

EN 61000-3-2:2014 • EN 61000-3-3:2013

This declaration of conformity is issued under the sole responsibility of the

manufacturer:

Grizzly Tools GmbH & Co. KG

Stockstädter Straße 20

D-63762 Großostheim, Germany

20.09.2016

* The object of the declaration described above satises the provisions of Directive 2011/65/EU

of the European Parliament and the Council of 8 June 2011 on limiting the use of certain harmful

substances in electrical and electronic appliances.

Volker Lappas

(Documentation Representative)

GB

IE

NI

Page is loading ...

GRIZZLY TOOLS GMBH & CO. KG

Stockstädter Straße 20

DE-63762 Großostheim

GERMANY

Last Information Update · Stand der Informationen:

09 / 2016 · Ident.-No.: 72037255092016-GB / IE / NI

IAN 275401

275401_par_Multifunktionsschleifer_cover_GB_IE_NI.indd 1 22.09.16 12:31

Parkside PMFS 200 B2 Translation Of The Original Instructions

Parkside PMFS 200 B2 Translation Of The Original Instructions

in other languages

Related papers

Other documents