Black Horse Model BH121 User manual

SPECIFICATION

Instruction Manual book



 Wingspan : 1,750 mm 68.90 in.



 Length :



 Weight : 4,4 kg 9.68 Lbs.



 Radio : 07 channels.



 Servo : 08 servos.

1,285 mm 50.59 in.



 Engine : 55 - 2 Stroke

15 CC Gas.



Electric Motor: RIMFIRE.80

 Battery: 18.5 -22.2V(5-6S LIPO)

 Propeller: 15X 6

Speed control: 60A.

ITEM CODE:BH 121.

Made in Vietnam.

2

Impulse 100TD - Item code: BH 121 . Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your Impulse 100TD. Use the parts listing below to

identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C supplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

procedures designed to help the new pilot on his way to successful R/C flight. They will also be able

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

 Thick cyanoacrylate glue.

 30 minute epoxy.

 5 minute epoxy.

 Hand or electric drill.

 Assorted drill bits.

 Modelling knife.

 Straight edge ruler.

 2mm ball driver.

 Phillips head screwdriver.

 220 grit sandpaper.

 90° square or builder’s triangle.

 Wire cutters.

 Masking tape & T-pins.

 Thread-lock.

 Paper towels.

Some more parts.

HARDWARE PACK

COWLING.

Landing gear.....

To avoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craft and to protect the table. Keep a couple of

jars or bowls handy to hold the small parts af-

ter you open the bag.

Please trial fit all the parts. Make sure you have

the correct parts and that they fit and are

aligned properly before gluing! This will assure

proper assembly. Impulse 100TD

ARF is hand

made from natural materials, every plane is

unique and minor adjustments may have to

be made. However, you should find the fit su-

perior and assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the follow-

ing: paint thinner, C/A glue accelerator, C/A glue

debonder and acetone. Do not let these chemi-

cals come in contact with the colors on the

covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

 (1) Fuselage.

WING ASSEMBLY

 (1) Right wing half with pre-installed

aileron.

 (1) Left wing half with pre-installed

aileron.

Tail section assembly

 (1) Vertical stabilizer with pre-

installed rudder.

 (1) Horizontal stabilizer with pre-

installed elevator halves.

SUGGESTION.

NOTE.

3

Impulse 100TD - Item code: BH 121 . Instruction Manual

Caution: this model is not a toy!

If you are a beginner to this type of powered

model, please ask an experienced model flyer

for help and support. If you attempt to operate

the model without knowing what you are doing

you could easily injure yourself or somebody

else. Please keep your safety and well-being

in mind at all times.

Important: before you start construction

Even if you have already built a large number

of RC models please read right through these

instructions and check all the kit components

against the parts list. We have taken great

trouble to keep construction as simple as

possible, without making any compromises

in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the

film covering due to major fluctuations in

weather conditions (temperature, humidity

etc.); in rare cases you may even find a slight

warp in a component. These minor faults are

in the nature of film-covered built-up wooden

structures, and can easily be corrected using

a heat gun, as commonly used for modelling.

Creases: Blow warm air over the area

and rub down with a soft

cloth.

When self-tapping screws have to be

screwed into wood, apply a little white

glue to prevent them shaking loose: just

squirt white glue into the hole and fit the

screw.

+ This is not a toy

+ Be sure that no other flyers are using your

radio frequency.

+ Do not smoke near fuel

+ Store fuel in a cool, dry place, away from

children and pets.

+ Wear safety glasses.

+The glow plug clip must be securely at-

tached to the glow plug.

+ Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from

the propeller.

+ Do not start the engine if people are near.

Do not stand in line with the side of the pro-

peller.

+ Make engine adjustments from behind the

propeller only. Do not reach around the spin-

ning propeller.

SAFETY PRECAUTION.

Wing warp: Hold the panel twisted

gently in the opposite

direction to the warp, and

apply warm air to remove

the creases from the

covering.

Caution! do not heat the film more than is

absolutely necessary. If the air or the iron is

too hot, the film may melt and holes may be

formed.

This model is highly pre-fabricated and can

be built in a very short time. However, the work

which you have to carry out is important and

must be done carefully. The model will only

be strong and fly well if you complete your

tasks competently - so please work slowly

and accurately.

REPLACEMENT LARGE PARTS

C. Fuselage.

D. Horizontal stabilizer.

E.Rudder. G. Decal sheet .

F. Aluminium wing dihedral brace.A. Cowling.

B. Wing panel(Right/Left).

A.

B.

E.

D.

G.

C.

B.

D.

F.

4

Impulse 100TD - Item code: BH 121 . Instruction Manual

REPLACEMENT SMALL PARTS

 1. Install the rubber grommets and brass

eyelets onto the aileron servo.

7. Wheels.

2. Wheel pants.

3. Fuel Tank.

5. Tail gear set.

8. Spinner.

9. Plastic parts for elevator and rudder pushrod.

1. Aluminium landing gear.(Right & Left).

6. Plastic parts for landing gear.

4. Engine mount ply of wood .

1.INSTALLING THE AILERON SERVO.

I. SERVO

Bottom side

Aileron

C/A glue.

5

Impulse 100TD - Item code: BH 121 . Instruction Manual

C/A glue.

2. Using a modeling knife, remove the cov-

ering servo tray.

Servo tray.

Remove covering

C/A glue.

6

Impulse 100TD - Item code: BH 121 . Instruction Manual

Repeat the procedure for the other wing

half.

 3. Drill 1,5mm pilot holes through the block

of wood for each of the four mounting screws

provided with the servo. Install servo into ai-

leron servo tray as same as picture below.

4. Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

 5. Instal servo tray with aileron servo into

the wing as same as picture below.

2x10mm.

2. INSTALLING THE AILERON CONTROL HORN.

Secure.

Aileron control horn

Install aileron control horn as same

as picture below.

Secure.

Thread.

Electric

wire.

7

Impulse 100TD - Item code: BH 121 . Instruction Manual

A+B Epoxy

PLUS

A+B Epoxy

PLUS

Repeat the procedure for the other wing

half.

Installing the aileron linkages as pictures

below.

Attach the clevis to the outer hole in the con-

trol horn.

3.INSTALLING THE AILERON

LINKAGES .

II. FLAP

1. INSTALLING THE FLAP SERVO .

60mm

M2.

Thread

Electric

wire

Control horn

of the aileron

8

Impulse 100TD - Item code: BH 121 . Instruction Manual

2x10mm.

Secure.

2. INSTALLING THE FLAP CONTROL HORN.

Repeat the procedure for the other wing

half.

Control horn of the flap

A+B Epoxy

PLUS

Control horn

of the flap

Installing the aileron linkages as pictures

below.

60 mm

M2.

3.INSTALLING THE FLAP

LINKAGES.

9

Impulse 100TD - Item code: BH 121 . Instruction Manual

Repeat the procedure for the other wing

half.

Bottom side

Flap

Aileron

THERE ARE TWO OPTIONS:

1. ELECTRIC MOTOR

2. ENGINE MOUNT.

1.

OPTION 1: ELECTRIC MOTOR

INSTALLING ELECTRIC MOTOR.

Drill a hole

2 mm diameter

Remove

Wood.

3x 15mm

Secure.

10

Impulse 100TD - Item code: BH 121 . Instruction Manual

Machine screw.

C/A glue.

3 x 15mm

Front view.

Secure.

Front view.

Right side

Rotor sharft.

Motor.

Left side.

Battery.

11

Impulse 100TD - Item code: BH 121 . Instruction Manual

Secure.

 1. Install one adjustable metal connector

through the third hole out from the center of

one servo arm, enlarge the hole in the servo

arm using a 2mm drill bit to accommodate the

servo connector. Remove the excess mate-

rial from the arm.

After installing the adjustable metal con-

nector apply a small drop of thin C/A to

the bottom nut. This will prevent the con-

nector from loosening during flight.

INSTALLING THE THROTTLE - CABLE.

Throttle servo

Front view.

ELECTRIC

POWER

See pictures below:

2. OPTION 2: ENGINE MOUNT

INSTALLING THE ENGINE MOUNT.

5x 80mm

Drill a hole

6mm diameter

12

Impulse 100TD - Item code: BH 121 . Instruction Manual

INSTALLING THE STOPPER ASSEMBLY



1) The stopper has been pre-assembled

at the factory.



2) Using a modeling knife, cut one length

of silicon fuel line (the length of silicon fuel line

is calculated by how the weighted clunk should

rest about 8mm away from the rear of the tank

and move freely inside the tank). Connect one

end of the line to the weighted clunk and the

other end to the nylon pick up tube in the stop-

per.



3) Carefully bend the second nylon tube

up at a 45 degree angle (using a cigarette

lighter). This tube will be the vent tube to the

muffler.



4) Carefully bend the third nylon tube down

at a 45 degree angle (using a cigarette lighter).

This tube will be vent tube to the fueling valve.

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

below the top surface of the tank. It should not

touch the top of the tank.

Throttle - cable

Throttle servo

Throttle - cable

FUEL TANK.

13

Impulse 100TD - Item code: BH 121 . Instruction Manual

Do not secure the tank into place perma-

nently until after balancing the airplane.

You may need to remove the tank to mount

the battery in the fuel tank compartment.

Blow through one of the lines to ensure

the fuel lines have not become kinked inside

the fuel tank compartment. Air should flow

through easily.



9) To secure the fuel tank in place, apply a

bead of silicon sealer to the forward area of

the tank, where it exits the fuselage behind the

engine mounting box and to the rear of the tank

at the forward bulkhead.



8) Feed three lines through the fuel tank

compartment and through the pre-drilled hole

in the firewall. Pull the lines out from behind

the engine, while guiding the fuel tank into

place. Push the fuel tank as far forward as

possible, the front of the tank should just about

touch the back of the firewall.



7) Using a modeling knife, cut 3 lengths of

fuel line 150mm long. Connect 2 lines to the 2

vent tubes and 1 line to the fuel pickup tube in

the stopper.



5) Test fit the stopper assembly into the

tank. It may be necessary to remove some of

the flashing around the tank opening using

a modeling knife. If flashing is present, make

sure none of it falls into the tank.

 6) When satisfied with the alignment of

the stopper assembly tighten the 3mm x 20mm

machine screw until the rubber stopper ex-

pands and seals the tank opening. Do not over

tighten the assembly as this could cause the

tank to split.

Tygon gas tubing not

included only use for

gasoline

silicon tube not included

only use for glow fuel.

Secure

Fuel tank

Tie wrap.

14

Impulse 100TD - Item code: BH 121 . Instruction Manual

Right side.

 1. Slide the fiberglass cowl over the en-

gine and line up the back edge of the cowl with

the marks you made on the fuselage.

COWLING.

Bottom side.

Top side.

center line 1.

Mark point 1.

15

Impulse 100TD - Item code: BH 121 . Instruction Manual

 4. Install the muffler and muffler extension

onto the engine and make the cutout in the

cowl for muffler clearance. Connect the fuel

and pressure lines to the carburetor, muffler

and fuel filler valve.

 2. While keeping the back edge of the

cowl flush with the marks, align the front of

the cowl with the crankshaft of the engine. The

front of the cowl should be positioned so the

crankshaft is in nearly the middle of the cowl

opening. Hold the cowl firmly in place using

pieces of masking tape.

 3. Slide the cowl back over the engine

and secure it in place using four wood screws.

Trim and cut.

center line 2

center line 2.

Mark point 2.

Drill 2mm

hole.

16

Impulse 100TD - Item code: BH 121 . Instruction Manual

Install the spinner backplate, propeller and

spinner cone. The spinner cone is held in

place using two 3mm x 8mm machine screws.

3 x 12mm

Secure

Front view

Secure.

INSTALLING THE SPINNER.

17

Impulse 100TD - Item code: BH 121 . Instruction Manual

 1. Install the rubber grommets and brass

collets into the elevator servo. Test fit the

servo into the servo tray.

 2. Mount the servo to the tray using the

mounting screws provided with your radio

system.

Elevator

servo

HORIZONTAL STABILIZER.

Horizontal stabilizer installation

See picture below.

C/A glue.

Bottom side.

Secure.

INSTALLING THE ELEVATOR

SERVOS.

18

Impulse 100TD - Item code: BH 121 . Instruction Manual

C/A glue.

Bottom side.

165 mm

9mm

19

Impulse 100TD - Item code: BH 121 . Instruction Manual

Epoxy glue

.

Elevator control horn install as same as the

way of aileron control horn.

Please see pictures below.

ELEVATOR CONTROL HORN INSTALLA-

TION.

C/A glue.

A+B

Epoxy glue.

Elevator

control horn.

Control horn of Elevator.

Bottom side.

20

Impulse 100TD - Item code: BH 121 . Instruction Manual

 Elevator pushrod install as same as the way

of aileron pushrod.

ELEVATOR PUSHROD INSTALLATION.

Elevator

pushrod

Bottom side

Elevator

pushrod

Elevator

pushrod

Rudder Servo.

M2

M2 lock nut.

Rudder servo install as same as method of

elevator servo. See picture below:

M2

M2 lock nut.

VERTICAL STABILIZER INSTALLATION.

Bottom side.

Page is loading ...

Black Horse Model BH121 User manual

This manual is also suitable for

Black Horse Model BH121 User manual

Related papers

Other documents