TOA FS-7010RM User manual

INSTALLATION MANUAL

VOICE EVACUATION SYSTEM

FS-7000 SERIES

Thank you for purchasing TOA's Voice Evacuation System.

Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

3

TABLE OF CONTENTS

1. SAFETY PRECAUTIONS ................................................................................. 5

2. SYSTEM SUMMARY ......................................................................................... 7

3. FEATURES ........................................................................................................... 8

4. INSTALLATION PRECAUTIONS ................................................................... 8

5. NOMENCLATURE AND FUNCTIONS

5.1. FS-7000CP Control Panel ................................................................................. 9

5.2. FS-7010CP Expansion Control Panel ............................................................. 13

5.3. FS-7000JP Junction Panel .............................................................................. 14

5.4. FS-7000PS DC Power Supply Panel .............................................................. 16

5.5. FS-7000AT Attenuator Control Panel ............................................................. 17

5.6. FS-7000EV Voice Evacuation Panel ............................................................... 18

5.7. FS-7000GM Group Matrix Panel ..................................................................... 20

5.8. FS-7000RF Remote Microphone Interface Panel ........................................... 21

5.9. FS-7000RM Remote Microphone ................................................................... 23

5.10. FS-7010RM Remote Microphone Extension ................................................... 25

5.11. FS-7006PA/7012PA Power Amplifiers ............................................................ 26

5.12. YA-7000 Amplifier Auto Switching Module ...................................................... 28

6. CONNECTIONS

6.1. Basic System Configuration ............................................................................. 29

6.2. Zone Expansion ............................................................................................... 31

6.3. 24 V DC Power Supply Expansion ................................................................... 33

6.4. Power Amplifier Expansion .............................................................................. 34

6.5. 2-Channel Broadcasts ...................................................................................... 35

6.6. Systems Combining the FS-7000RF, FS-7000RM, and FS-7010RM .............. 37

6.6.1. Connecting the FS-7000RF to 2 FS-7000RMs ...................................... 40

6.6.2. Joining the FS-7000RM to the FS-7010RM ........................................... 42

6.7. FS-7000GM

6.7.1. Changing the FS-7000CP's/7010CP's zone selector keys

into group selector keys ......................................................................... 43

6.7.2. Changing the FS-7000RM's zone selector keys

into group selector keys ......................................................................... 49

6.8. Connecting the FS-7000AT to 4-Wire System Attenuators .............................. 51

6.9. Standby Amplifiers ........................................................................................... 54

6.10. Timer-Operated Equipment .............................................................................. 56

6.11. Telephone Paging ............................................................................................ 56

6.12. BGM Players .................................................................................................... 57

6.13. FS-7000EV ....................................................................................................... 58

6.14. Automatic Fire Alarm Systems ......................................................................... 59

6.15. Power Failure Backup

6.15.1. Providing Backup Power Using

an Uninterruptible Power Supply (UPS) System ................................. 60

6.15.2. Power Backup Using

the DS-029B Emergency Power Supply Panel .................................... 60

4

7. TABLE FOR CABLES

7.1. Cables Supplied with Equipment ..................................................................... 64

7.2. Cables To Be Prepared by the Customers

7.2.1. FS-7000CP Control Panel .................................................................... 66

7.2.2. FS-7010CP Expansion Control Panel ................................................... 66

7.2.3. FS-7000JP Junction Panel ................................................................... 67

7.2.4. FS-7000PS DC Power Supply Panel .................................................... 67

7.2.5. FS-7000AT Attenuator Control Panel ................................................... 67

7.2.6. FS-7000EV Voice Evacuation Panel .................................................... 68

7.2.7. FS-7000GM Group Matrix Panel .......................................................... 68

7.2.8. FS-7000RF Remote Microphone Interface Panel ................................. 68

7.2.9. FS-7000RM Remote Microphone ......................................................... 68

7.2.10. FS-7006PA/7012PA Power Amplifiers .................................................. 69

7.2.11. YA-7000 Amplifier Auto Switching Module ........................................... 69

8. REMOVABLE TERMINAL PLUG CONNECTION .................................. 70

9. PARTS INSTALLATION

9.1. Installing Diodes on the FS-7000GM's Circuit Board ....................................... 71

9.2. Changing the Operation Mode of the FS-7000RM Microphone ....................... 75

10. MOUNTING THE YA-7000 IN THE POWER AMPLIFIER .................... 76

11. FAILURE INDICATION .................................................................................... 77

12. SPECIFICATIONS

12.1. FS-7000CP Control Panel ............................................................................. 79

12.2. FS-7010CP Expansion Control Panel ........................................................... 80

12.3. FS-7000JP Junction Panel ............................................................................ 81

12.4. FS-7000PS DC Power Supply Panel ............................................................ 82

12.5. FS-7000AT Attenuator Control Panel ........................................................... 82

12.6. FS-7000EV Voice Evacuation Panel ............................................................. 83

12.7. FS-7000GM Group Matrix Panel ................................................................... 84

12.8. FS-7000RF Remote Microphone Interface Panel ......................................... 84

12.9. FS-7000RM Remote Microphone ................................................................. 85

12.10. FS-7010RM Remote Microphone Extension ................................................. 85

12.11. FS-7006PA/7012PA Power Amplifiers .......................................................... 86

12.12. YA-7000 Amplifier Auto Switching Module .................................................... 87

1. SETTINGS TABLE ........................................................................................... 88

2. FS-7000RM/FS-7010RM ZONE IDENTIFICATION CARDS ............... 91

SUPPLEMENT

5

When Installing the Unit

• FS-7000PS/7006PA/7012PA only

Do not expose the unit to rain or an environment

where it may be splashed by water or other liquids,

as doing so may result in fire or electric shock.

Use the unit only with the voltage specified on the

unit. Using a voltage higher than that which is

specified may result in fire or electric shock.

Do not cut, kink, otherwise damage nor modify the

power supply cord. In addition, avoid using the

power cord in close proximity to heaters, and never

place heavy objects -- including the unit itself -- on

the power cord, as doing so may result in fire or

electric shock.

• FS-7006PA/7012PA, YA-7000 only

Be sure to replace the unit's terminal cover after

connection completion. Because the voltage of up

to 100 V is applied to the high impedance speaker

terminals (FS-7006PA/7012PA, YA-7000) and

Main/standby Amplifier terminals (YA-7000), never

touch these terminals to avoid electric shock.

• All units

Avoid installing or mounting the unit in unstable

locations, such as on a rickety table or a slanted

surface. Doing so may result in the unit falling

down and causing personal injury and/or property

damage.

Install the unit only in a location that can

structurally support the weight of the unit and the

mounting bracket. Doing otherwise may result in

the unit falling down and causing personal injury

and/or property damage.

Owing to the unit's size and weight, be sure that at

least two persons are available to install the unit.

Failure to do so could result in personal injury.

Tighten each nut and bolt securely. Ensure that the

bracket has no loose joints after installation to

prevent accidents that could result in personal

injury.

When the Unit is in Use

• FS-7000PS/7006PA/7012PA only

To prevent a fire or electric shock, never open nor

remove the unit case as there are high voltage

components inside the unit. Refer all servicing to

qualified service personnel.

Do not place cups, bowls, or other containers of

liquid or metallic objects on top of the unit. If they

accidentally spill into the unit, this may cause a fire

or electric shock.

Do not insert nor drop metallic objects or

flammable materials in the ventilation slots of the

unit's cover, as this may result in fire or electric

shock.

Do not touch a plug during thunder and lightning,

as this may result in electric shock.

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe

operation.

• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or

cautions regarding safety.

• After reading, keep this manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent bodily injury and property

damage which could result from mishandling. Before operating your product, read this manual first and

understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.

WARNING

Indicates a potentially hazardous situation which, if mishandled, could

result in death or serious personal injury.

Indicates a potentially hazardous situation which, if mishandled, could

result in moderate or minor personal injury, and/or property damage.

WARNING

CAUTION

6

When the Unit is in Use

• All units

Should the following irregularity be found during

use, immediately switch off the power, disconnect

the power supply plug from the AC outlet and

contact your nearest TOA dealer. Make no further

attempt to operate the unit in this condition as this

may cause fire or electric shock.

· If you detect smoke or a strange smell coming

from the unit.

· If water or any metallic object gets into the unit

· If the unit falls, or the unit case breaks

· If the power supply cord is damaged (exposure of

the core, disconnection, etc.):

FS-7000PS/7006PA/7012PA only

· If it is malfunctioning (no tone sounds.)

When Installing the Unit

• FS-7000PS/7006PA/7012PA only

Never plug in nor remove the power supply plug

with wet hands, as doing so may cause electric

shock.

When unplugging the power supply cord, be sure

to grasp the power supply plug; never pull on the

cord itself. Operating the unit with a damaged

power supply cord may cause a fire or electric

shock.

When moving the unit, be sure to remove its power

supply cord from the wall outlet. Moving the unit

with the power cord connected to the outlet may

cause damage to the power cord, resulting in fire or

electric shock. When removing the power cord, be

sure to hold its plug to pull.

Do not block the ventilation slots in the unit's cover.

Doing so may cause heat to build up inside the unit

and result in fire. Also, periodically clean the

ventilation slots of dust.

To avoid electric shocks, be sure to switch off the

unit's power when connecting speakers.

Be sure to follow the instructions below when rack-

mounting the unit. Failure to do so may cause a fire

or personal injury.

· Install the equipment rack on a stable, hard floor.

Fix it with anchor bolts or take other arrangements

to prevent it from falling down.

· When connecting the unit's power cord to an AC

outlet, use the AC outlet with current capacity

allowable to the unit.

• All units

Avoid installing the unit in humid or dusty locations,

in locations exposed to the direct sunlight, near the

heaters, or in locations generating sooty smoke or

steam as doing otherwise may result in fire or

electric shock.

When unpacking or moving the unit, be sure to

handle it with two or more persons. Falling or

dropping the unit may cause personal injury and/or

property damage.

When the Unit is in Use

• FS-7006PA/7012PA only

Do not operate the unit for an extended period of

time with the sound distorting. This is an indication

of a malfunction, which in turn can cause heat to

generate and result in a fire.

• FS-7000CP/7006PA/7012PA only

Make sure that the volume control is set to

minimum position before power is switched on.

Loud noise produced at high volume when power is

switched on can impair hearing.

• FS-7000PS/7006PA/7012PA only

If dust accumulates on the power supply plug or in

the wall AC outlet, a fire may result. Clean it

periodically. In addition, insert the plug in the wall

outlet securely.

Switch off the power, and unplug the power supply

plug from the AC outlet for safety purposes when

cleaning or leaving the unit unused for 10 days or

more. Doing otherwise may cause a fire or electric

shock.

• All units

Contact your TOA dealer as to the cleaning. If dust

is allowed to accumulate in the unit over a long

period of time, a fire or damage to the unit may

result.

CAUTION

WARNING

7

2. SYSTEM SUMMARY

FS-7000PS

FS-7000EV

FS-7000AT

PBX

FS-7000RM

FS-7006PA

YA-7000

FS-7000RF

FS-7010CP

FS-7006PA

230 V AC

50 Hz

24 V DC (supplied to rack internal components)

Confirmation signal

Automatic fire alarm system

Floor identifier signals 1 – 10

CP microphone

Sound source

Timer-operated

sound source

BGM player

OUT

RF CONT

BGM

FS-7000CP

ContEV IN

TIMER

BUSY

FLOOR ID

CP MIC

TALK SW

AUX

CALL

BUSY

RF CONT

PRIORF IN

RF ZONE

CP CONT

JP CONT

ZONES 1 – 10

Max. 50 zones

FS-7000JP

AT CONT

Speaker outputs 1 – 10

Attenuator controls

1 – 10

ZONES 11 – 20

CP CONT

RF CONT

GM CONT

JP CONT

Floor identifier signals

11 – 20

Speaker outputs

11 – 20

Attenuator controls

11 – 20

FS-7000JP

AT CONT

FS-7000AT

: Control line, 1-way

: Control line, 2-way

: Audio signal

: Speaker output (priority)

: Speaker output (BGM)

8

3. FEATURES

• The FS-7000EV is loaded with English language messages when shipped from the factory.

• The semiconductor memory incorporated in the FS-7000EV ensures stable rebroadcast of recorded

messages.

• If speaker lines are shorted, the line protection fuse disconnects the shorted lines and a line short indication

is displayed.

• Simultaneous 2-channel broadcasts can be made of BGM (background music) and announcement

broadcasts (emergency and priority broadcasts), allowing BGM broadcasts to continue in zones not selected

for announcement broadcasts, even when announcements are being made.

• Up to 4 remote microphones can be connected.

• Up to 200 speaker lines can be controlled.

• Time signals can be simultaneously broadcast over all zones by connecting timer-operated sound sources.

• All-zone calls can be made from a telephone set by connecting the system to a telephone exchange.

• Connection of the emergency power supply panel permits emergency broadcasts to be made even during a

power failure.

4. INSTALLATION PRECAUTIONS

• The required power voltage for this system is 230V AC. Calculate the total combined power consumption of

all equipment in the system to ensure ample power capacity. Note that the system may not work properly

due to breaker cutoff or power voltage drops when the total supply voltage is insufficient.

• About the handling of the power supply cord (FS-7000PS only):

The supplied power cord is intended for exclusive use with the FS-7000PS Power Supply Panel. Avoid using

this power cord for any other equipment than the PS-7000PS panel.

• Ensure that the rear of the component is sufficiently distant from the rear wall to facilitate maintenance

service. Speaker line protection fuses and output overcurrent fuses are located on the component rear

panel. Sufficient space must be provided between the back of the component and the rear wall surface to

change the fuses.

• When mounting the FS-7000PS and FS-7006PA or FS-7012PA in an equipment rack, mount a Perforated

Panel larger than 1U size* just above and below each component, as shown in the following figure.

• When mounting the FS-7006PA or FS-7012PA power amplifier in an equipment rack, keep the rear of the

amplifier at least 10 cm away from the rear wall so that its rear panel-mounted fan vent is not blocked.

• Each component is designed with robust construction. However, be sure to use reinforcement brackets

when mounting if extra strength is required.

• No rack mounting screws are supplied with the system. Use the appropriate screws for the racks used.

*1U size = 44.5 mm (standard size)

Perforated Panels

Power Amplifiers

FS-7006PA/7012PA

DC Power Supply Panel

FS-7000PS

9

5. NOMENCLATURE AND FUNCTIONS

5.1. FS-7000CP Control Panel

The FS-7000CP is a standard operation panel for the FS-7000 Series Voice Evacuation Systems.

It is designed to be used in conjunction with the FS-7000JP panel, and enables individual paging calls to up to

10 zones plus all-zone calls.

The number of zones can be expanded to up to 200 zones in 10-zone units by connecting the FS-7010CP

expansion panel. Further, connection of both the FS-7000GM panel and the FS-7010CP panel permits

creation of up to 20 broadcast zone groups.

The FS-7000CP is equipped with a built-in pre-amplifier function and chime unit (ascending 4-note tone).

Audio output can be set to either a 2-channel output of background music (BGM) and priority broadcast or a 1-

channel output of mixed BGM and priority broadcast.

[Front]

2

3

1

7 9 10 11 12 136 148

5

4

Inside of the front cover

1. Power Indicator

Lights when power is supplied and the FS-

7000CP is ready for operation.

2. CP Microphone

Make announcements while holding down the

Talk Switch (3). The microphone can be used only

while the FS-7000CP panel is in use or

emergency broadcasts are in progress.

3. Talk Switch

Hold down this switch to make announcements

using the microphone.

4. Volume Controls

Adjust the sound volume for each audio input.

Turning the control clockwise increases the

volume, while turning it counterclockwise

decreases the volume.

Controls are arranged from left to right as follows:

• EV

Adjusts the volume of the EV Audio Input on the

rear panel.

• TIMER

Adjusts the volume of the Timer Input on the rear

panel.

• PAGING

Adjusts the volume of the Paging Input on the rear

panel.

• RM MIC

Adjusts the volume of the RF Audio Input on the

rear panel.

• CP MIC

Adjusts the volume of the CP Microphone (2).

• CHIME

Adjust the volume of the built-in 4-tone chime.

• BGM 1 – 4

Adjusts the volume of BGM Inputs 1 – 4 on the

rear panel.

10

5. Tone Controls

Adjust high and low frequencies of the output.

Frequencies are accentuated when the control is

rotated clockwise, and attenuated when rotated

counterclockwise. Controls are arranged from left

to right as follows:

• PRIORITY BASS

Adjusts the low frequencies of the Priority Output

on the rear panel.

• PRIORITY TREBLE

Adjusts the high frequencies of the Priority Output

on the rear panel.

• BGM BASS

Adjusts the low frequencies of the BGM Output on

the rear panel.

• BGM TREBLE

Adjusts the high frequencies of the BGM Output

on the rear panel.

6. Zone Indicators

Light to indicate current broadcast zones.

Note

These indicators also light during emergency

broadcasts when broadcast zones are selected by

signal inputs from an automatic fire alarm system.

7. Zone Selector Keys

Press these keys to select broadcast zones. To

cancel the selection, press the keys again.

Multiple broadcast zones can be selected

simultaneously with the additional use of the FS-

7000GM panel.

8. Busy Status Indicators

The indicator corresponding to the component

currently in use for broadcast lights while the

system is in general-purpose broadcast mode.

Note

These indicators do not light during emergency

broadcasts.

The priorities of the indicators are: TIMER,

PAGING, RM MIC, and CP IN-USE from high to

low. (Emergency broadcasts take precedence

over all other equipment operations.)

Each indicator is arranged from left to right as

follows:

• TIMER

Remains lit during broadcasts from the component

connected to the timer input.

• PAGING

Remains lit during broadcasts from the

component connected to the paging input.

• RM MIC

Remains lit during broadcasts from the FS-

7000RM.

• CP IN-USE

Remains lit during broadcasts from the FS-

7000CP. Announcements can be made via the

CP Microphone (2).

9. Speaker Line Short Indicator

Lights when 1 or more speaker lines connected

to the FS-7000JP have shorted.

(See page 77.)

10. All-Zone Call Indicator

Lights when the All-Zone Call button (13) is

pressed to select all broadcast zones

simultaneously. (Lights continuously only while

the FS-7000CP is operating or emergency

broadcasts are being made.)

11. Chime Button

Sounds a built-in 4-tone chime. This button can

be used only while the FS-7000CP is operating.

12. Reset Button

Resets the broadcast zones selected with the

Zone Selector keys (7) or All-Zone Call button

(13). Pressing this button also terminates

general-purpose broadcasts provided from the

FS-7000CP.

13. All-Zone Call Button

Selects all broadcast zones simultaneously.

14. Broadcast Zone Fill-In Space

Write the names of zones to be selected with the

Zone Selector keys (7) in this space.

11

[Rear]

2721 22 23 24 25

18 19

20

16 1715

26

28 30 31 32 33 34 35 3629 37 38

15. DC Power Input Terminal

Connect 24 V DC power to this terminal. Power

is supplied from the FS-7000PS.

(M3 screw terminal; barrier distance: 6.4 mm)

16. BGM Input Terminals 2,3,4

Connect background music equipment to these

terminals. When the output is set to 2-channel

broadcast, background music is supplied from

the BGM Output (30). When the output is set to

1-channel broadcast, background music is mixed

with priority broadcasts and provided from the

Priority Output (31) as well. However, activation

of the muting function* due to signal inputs other

than BGM will attenuate the BGM level.

BGM inputs 2 – 4: –20 dBV, 10 kΩ, unbalanced,

2P RCA jack

* Muting function: A function that automatically

decreases the volume of original broadcast when

another broadcast is initiated during original

broadcast, and restores the original broadcast

volume level when the other broadcast is

completed.

17. Mute Switch

Sets whether or not to attenuate the signal levels

of BGM Inputs 2 – 4 (16) when a broadcast is

made from the BGM Input 1 (18). (Default: OFF)

18. BGM Input Terminal 1

Connect background music equipment to this

terminal. When the output is set to 2-channel

broadcast, BGM is supplied from the BGM

Output (30). Setting the muting function permits

this input to take precedence over BGM Inputs 2

– 4. When the output is set to 1-channel

broadcast, background music is mixed with

priority broadcasts and provided from the Priority

Output (31) as well. However, activation of the

muting function due to signal inputs other than

BGM will attenuate the BGM level. (–60 dBV/0

dBV selectable, 600 Ω, balanced, 3P terminal

block)

19. BGM Input 1 Sensitivity Selector Switch

Sets the input sensitivity of BGM Input 1 (18) to

"–60 dBV" or "0 dBV." (Default: 0 dBV)

20. Paging Input Terminal

Connect audio and control signals from

equipment (such as telephone paging

equipment) to this terminal. Input signals to this

terminal are broadcast when the control

terminals are closed.

Audio: –60 dBV/–20 dBV selectable, 600 Ω,

balanced

Control: Open voltage: 26 V DC; short-circuit

current: under 2 mA

5P terminal block

21. Paging Input Sensitivity Selector Switch

Sets the input sensitivity of Paging Input (20) to

"–60 dBV" or "–20 dBV."

(Default: –20 dBV)

22. RF Audio Input Terminal

Used to connect the FS-7000RF. Audio signals

from the FS-7000RM are input via the FS-

7000RF. (0 dBV, 600 Ω, balanced, 3P terminal

block)

23. Auxiliary Input Terminal

Signals received by this terminal are mixed with

signals from the CP Microphone (2) and output

while the FS-7000CP is in operation.

(–20 dBV, 600 Ω, unbalanced, 2P terminal block)

24. Auxiliary Input Volume Control

Adjusts the sound volume of Auxiliary Input (23).

12

25. Timer Input Terminal

Connect audio and control signals from timer-

operated equipment to this terminal. Input

signals to this terminal are broadcast with the

highest priority when the control terminals are

closed.

Audio: 0 dBV, 600 Ω, unbalanced

Control: Open voltage: 26 V DC; short-circuit

current: under 2 mA

4P terminal block

26. EV Audio Input Terminal

Used to connect the FS-7000EV. This input can

be used only while an emergency broadcast is

being made. (0 dBV, 600 Ω, unbalanced, 2P

terminal block)

27. Output Mode Selector Switch

Sets the audio output to "1-CH" (1-channel) or

"2-CH" (2-channel) broadcasts.

(Default: 2-channel broadcast)

28. Functional Earth Terminal

Connect this terminal to the functional earth

terminal of external equipment if excessive noise

is generated when the FS-7000CP is connected

to the external equipment. This could reduce

noise.

Note: This terminal is not for protective earth.

29. All-Zone Call Mode Selector Switch

Sets the mode of broadcast to be initiated with

the All-Zone Call button (13). When the FS-

7000AT has been connected to the system, if

this switch is set to "URGE" (general urgency)

and an all-zone call is made, a 24 V DC for

controlling attenuators is output, permitting the

call to bypass the attenuator. (Default: "NORM")

30. BGM Output Terminal

Signals from the BGM Inputs 1 – 4 (16 and 18)

are mixed and output. Connect this terminal to

the power amplifier for BGM broadcast. (0 dBV,

600 Ω, balanced, 3P terminal block)

31. Priority Output Terminal

When the Output Mode Selector Switch (27)

is set to 2-channel broadcast:

Outputs signals other than those from the BGM

Inputs 1 – 4 (16 and 18). Connect this terminal to

the power amplifier intended for priority

broadcast.

When the Output Mode Selector Switch (27)

is set to 1-channel broadcast:

Outputs signals from all audio inputs. Signals

output from sources other than BGM Inputs 1 – 4

causes these 4 BGM input signals to atttenuate.

Connect this terminal to the power amplifier. (0

dBV, 600 Ω, balanced, 3P terminal block)

32. Automatic Fire Alarm System Input Terminal

Connect this terminal to the floor identifier signal

transmitted from the automatic fire alarm system.

The identifier signal automatically selects zones

and broadcasts audio alarms to such zones.

(Open voltage: 26 V DC; short-circuit current:

under 5 mA; 12P terminal block; 10 zones +

COM + COM)

Note

This terminal is not connected when the FS-

7000EV is not used.

33. EV Control Terminal

Connect the FS-7000EV to this terminal.

34. RF Zone Control Terminal

Use this terminal to connect the FS-7000RF.

Data regarding broadcast zones transmitted from

the FS-7000RF is input to this terminal.

35. RF Control Terminal

Use this terminal to connect the FS-7000RF.

36. CP Control Terminal

Use this terminal to connect the FS-7010CP. All

of the FS-7010CP units that are mounted in the

system must be connected to this terminal.

37. JP Control Terminal

Connect this terminal to the FS-7000JP when the

FS-7000GM is not connected to the system.

Note

This terminal is not used when the FS-7000GM

is connected to the FS-7000CP.

38. JP/GM Control Terminal

Connect this terminal to the FS-7000JP or FS-

7000GM.

When the FS-7000GM is not connected to the

FS-7000CP:

Connect this terminal to the FS-7000JP in order

to control speaker line ON/OFF operations.

When the FS-7000GM is connected to the FS-

7000CP:

Connect this terminal to the FS-7000GM. The

Zone Selector keys (7) on the front panel

function as group selector keys.

13

5.2. FS-7010CP Expansion Control Panel

The FS-7010CP is used to expand the broadcasting capacity of FS-7000 Series Voice Evacuation Systems.

Announcements and background music can be broadcast to up to 10 individual zones. Connecting the FS-

7000GM to the FS-7000CP/FS-7010CP combination permits broadcasts to be made to up to 20 zone groups.

[Front]

2 3 4 1

6 7 85 119 10 12

1. Power Indicator

Lights when power is supplied and the FS-

7010CP is ready for operation.

2. Zone Selector Keys

Press these keys to select broadcast zones. To

cancel the selection, press the keys again.

Multiple broadcast zones can be selected

simultaneously with the additional use of the FS-

7000GM.

3. Zone Indicators

Light to indicate current broadcast zones.

Note

These indicators also light during emergency

broadcasts when their corresponding zones are

selected by automatic fire alarm signals.

4. Broadcast Zone Fill-In Space

Write the names of zones to be selected with the

Zone Selector keys (2) in this space.

5. DC Power Input Terminal

Connect 24 V DC power to this terminal. Power is

supplied from the FS-7000PS.

(M3 screw terminal; barrier distance: 6.4 mm)

6. Functional Earth Terminal

Connect this terminal to the functional earth

terminal of external equipment if excessive noise

is generated when the external equipment is

connected to the FS-7010CP. This could reduce

noise.

Note: This terminal is not for protective earth.

7. Automatic Fire Alarm System Input Terminal

Connect this terminal to floor identifier signals

transmitted from the automatic fire alarm system.

The identifier signal designates broadcast zones

to provide audio alarm to such zones. (Open

voltage: 26 V DC; short-circuit current: under 5

mA; 12P terminal block; 10 zones + COM + COM)

Note: This terminal is not connected when the FS-

7000EV is not used.

8. RF Zone Control Terminal

Use this terminal to connect the FS-7000RF.

9. CP Control Terminal

Connect this terminal to the FS-7000CP or other

FS-7010CP units. All of the FS-7010CP units

within the system must be connected to the FS-

7000CP.

10. JP Control Terminal

Connect this terminal to the FS-7000JP Junction

Panel.

11. JP Zone Control Terminal

Connect this terminal to the FS-7000JP in order

to control speaker line ON/OFF operations.

12. GM Zone Control Terminal

Connect this terminal to the FS-7000GM when

the FS-7000GM is connected to the FS-7000CP.

[Rear]

14

1. Power Indicator

Lights when power is supplied and the FS-7000JP

panel is ready for operation.

2. BGM Zone Selector Keys

Press these keys to select BGM broadcast zones.

Press the keys again to cancel the selection. (2-

channel broadcast)

3. Speaker Line Indicators

Indicate speaker line operating statuses as

follows:

Green: BGM broadcast in progress (2-channel

broadcast)

Orange: BGM broadcast in progress (1-channel

broadcast) or priority or emergency

broadcasts in progress

Red: Short-circuit (see page 77.)

4. Broadcast Zone Fill-In Space

Write the names of zones to be selected with the

BGM Zone Selector keys (2) in this space.

5.3. FS-7000JP Junction Panel

The FS-7000JP panel is used in conjunction with the FS-7000CP and the FS-7010CP to connect speaker

lines in FS-7000 Series Voice Evacuation Systems. It can connect up to 10 speaker lines. If speaker lines are

shorted, the line protection fuses disconnect the shorted lines, leaving broadcasts to other speaker lines

functioning intact. The FS-7000JP is equipped with BGM input and priority broadcast input, with BGM

broadcast zones selectable using the keys on the front panel. Priority broadcast zones are selected using the

FS-7000CP.

[Front]

4 12 3

15

6

7 8

5

119 10 12 13 14 15 16

[Rear]

5. DC Power Input Terminal

Connect 24 V DC power to this terminal. Power

is supplied from the FS-7000PS.

(M3 screw terminal; barrier distance: 6.4 mm)

6. Speaker Output Terminal

Connect this terminal to speaker lines. Ten lines

can be connected.

Maximum per-line output (high impedance, 100

V line)

When the FS-7006PA amplifier is connected:

280 W

When the FS-7012PA amplifier is connected:

500 W

(M3 screw terminal; barrier distance: 6.4 mm)

7. Functional Earth Terminal

Connect this terminal to the functional earth

terminal of external equipment if excessive noise

is generated when the FS-7000JP panel is

connected to the external equipment. This could

reduce noise.

Note: This terminal is not for protective earth.

8. General Urgency/Emergency Mode Output

Terminal

Activated while a General urgency broadcast or

Emergency broadcast is being made.

(Open collector output; rated voltage: 30 V DC;

current capacity: 0.1 A; 2P terminal block)

9. Power Remote Output Terminal

Activated when a broadcast is made to any zone.

This terminal can be used for remotely

controlling the power amplifier's power supply.

(Relay output; rated voltage: 30 V DC; current

capacity: 1 A; 2P terminal block)

10. BGM Input Terminal

Connect this terminal to the power amplifier

intended for BGM broadcast.

(M4 screw terminal; barrier distance: 9 mm)

Note

Only 1 piece of FS-7006PA, FS-7012PA or YA-

7000 can be connected to this terminal. Never

connect 2 or more units to this terminal, as the

excessive load could cause the amplifier to fail.

11. Priority Input Terminal

Connect this terminal to the output of the power

amplifier intended for priority broadcast.

(M4 screw terminal; barrier distance: 9 mm)

Note

Only 1 piece of FS-7006PA, FS-7012PA or YA-

7000 can be connected to this terminal. Never

connect 2 or more units to this terminal, as the

excessive load could cause the amplifier to fail.

12. Attenuator Connection Terminal

Connect this terminal to the FS-7000AT.

13. Speaker Line Protection Fuses

Disconnect shorted speaker lines to prevent

adverse effects on other speaker lines.

Note

Install the fuse having the correct capacity for all

the connected speakers.

14. Reset Switch

Pressing this switch after removing the cause of

a speaker line short and replacing the blown

Speaker Line Protection Fuse (13) restores

broadcasts to that speaker line.

15. JP Control Terminal

Connect this terminal to the FS-7000CP and FS-

7010CP.

16. JP Zone Control Terminal

Connect this terminal to the FS-7000CP and FS-

7010CP to select speaker lines during priority

broadcasts.

16

5.4. FS-7000PS DC Power Supply Panel

The FS-7000PS supplies 24 V DC power to each component used in FS-7000 Series Voice Evacuation

Systems. Connecting the DS-029B provides a power supply for emergency broadcasts even during power

failures.

[Front]

1 2 3

6 7 85 119 104

1. AC Power Switch

AC power is turned on and off with each press of

this switch.

2. AC Power Indicator

Lights when AC power is supplied and the FS-

7000PS is ready for operation on AC power.

3. DC Power Indicator

Lights when DC power is supplied and the FS-

7000PS is ready for operation on DC power.

4. AC Power Inlet

Connect the supplied power cord to this inlet.

5. Functional Earth Terminal

Connect this terminal to the functional earth

terminal of external equipment if excessive noise

is generated when the external equipment is

connected to the FS-7000PS. This could reduce

noise.

Note: This terminal is not for protective earth.

6. AC Fuse

Protects the unit against output overcurrent when

the unit is operated on AC power. When replacing

the fuse, use the specified type.

7. 24 V DC Output Terminal

Connect this terminal to the 24 V DC input of each

system component.

M3 screw terminal; barrier distance: 6.4 mm;

current capacity: 5 A (total).

8. DC Fuse

Protects the unit against output overcurrent when

the unit is operated on DC power. When

replacing the fuse, use the specified type.

9. Grounding Terminal

Disconnects a 24 V DC output ground from a

frame ground. (Default: Shorted between F.G

and S.G)

(M3 screw terminal; barrier distance: 6.4 mm)

10. Emergency Power Connection Terminal

Connect this terminal to the DS-029B to enable

emergency broadcasts even during power

failures.

(M3 screw terminal; barrier distance: 6.4 mm)

11. Emergency Power Control Terminal

Activates an emergency power supply unit to

enable emergency broadcasts during power

failures. Connect this terminal to the FS-7000EV.

(M3 screw terminal; barrier distance: 6.4 mm)

[Rear]

17

5.5. FS-7000AT Attenuator Control Panel

The FS-7000AT is used in conjunction with FS-7000 Series Voice Evacuation Systems to control 4-wire

system attenuators. Up to 10 zones can be attenuator-controlled. When general urgency or emergency

broadcasts are made, the FS-7000AT provides 24 V DC power to allow such broadcasts to bypass the

attenuators. The output status of each line can be monitored by the indicators on the front panel.

[Front]

2 3 1

6 7 854

[Rear]

1. Power Indicator

Lights when power is supplied and the FS-7000AT

is ready for operation.

2. Attenuator Line Indicators

Light when 24 V DC for bypassing the attenuators

are being supplied, and extinguish when the

overcurrent protection circuit is triggered due to

line shorts or other failures, or when the power

supply is cut off.

3. Broadcast Zone Fill-In Space

Write the names of the corresponding broadcast

zones in this space.

4. DC Power Input Terminal

Connect this terminal to 24 V DC power to be

used for internal circuits. Power is supplied from

the FS-7000PS.

(M3 screw terminal; barrier distance: 6.4 mm)

5. Functional Earth Terminal

Connect this terminal to the functional earth

terminal of external equipment if excessive noise

is generated when the external equipment is

connected to the FS-7000AT. This could reduce

noise.

Note: This terminal is not for protective earth.

6. AT Control Terminal

Connect this terminal to the FS-7000JP to control

ON/OFF operations of the Attenuator Control

Output (8).

7. ATT DC Power Input Terminal

Connect this terminal to 24 V DC power used for

attenuator control to be output from the Attenuator

Control Output Terminals 1 – 10 (8).

(M3 screw terminal; barrier distance: 6.4 mm)

8. ATT Control Output Terminals

Provide 24 V DC output for bypassing the

attenuators during general urgency or emergency

broadcasts.

[M3 screw terminal; barrier distance: 6.4 mm;

maximum current capacity: 5 A (total of 10

lines)/0.75 A (per line)]

18

5.6. FS-7000EV Voice Evacuation Panel

The FS-7000EV is an emergency broadcast operation panel for FS-7000 Series Voice Evacuation Systems.

This panel is not required if the system is to be used solely for general-purpose public address applications. It

is possible to start and reset emergency broadcasts through manual operation. The FS-7000EV has a built-in

voice alarm device that can make both evacuation and false-alarm announcements. Not only are evacuation

announcements automatically broadcast when the system receives a fire instruction signal from the connected

automatic fire alarm system, they can also be initiated using the Evacuation Announcement button on the front

panel. False alarm announcements can be initiated using the False Alarm Announcement button on the front

panel. Evacuation and false alarm announcement messages can also be recorded using the appropriate

buttons on the front of the panel, in which case the recorded message can be confirmed by listening with

headphones.

[Front]

2 3 4 7 8 9

10 11 12 13

165

1. Power Indicator

Lights when power is supplied and the FS-

7000EV is ready for operation.

2. Emergency Reset Button

When it is confirmed that a fire has been

extinguished or other emergency situations have

returned to normal, press this button to terminate

emergency broadcasts after resetting the

connected automatic fire alarm system.

3. Fire Indicator

Indicates that an emergency broadcast is in

progress. This indicator lights when a fire

detection signal is transmitted from the automatic

fire alarm system or when the Emergency

Activation button (4) is pressed.

4. Emergency Activation Button

Press this button to manually initiate emergency

broadcasts after the occurrence of fire has been

confirmed.

5. Mode Selector Switch

Selects the operation mode of the FS-7000EV unit

to be used as a sound source for evacuation and

false alarm announcements. Set the mode to

"NORMAL" in general use. No voice alarm is

output when the mode is set to "MONITOR" or

"RECORD."

Functions of the 3 switch positions are as follows:

NORMAL: Select this mode in general use. Voice

alarms are provided at the time of

emergency broadcast.

MONITOR: Allows the operator to listen to

messages recorded on a sound

source.

RECORD: Records evacuation and false alarm

announcements on a sound source.

(Default: NORMAL)

6. Evacuation Announcement Indicator

Lights or flashes when an evacuation

announcement is played back or recorded.

7. Evacuation Announcement Button

Press this button to play back or record

evacuation announcements.

8. False Alarm Announcement Indicator

Lights or flashes when a false alarm

announcement is played back or recorded.

9. False Alarm Announcement Button

Press this button to play back or record false

alarm announcements.

10. Input Sensitivity Setting Switch

Sets the input sensitivity of Recording Input (11).

Select the sensitivity depending on the type of

connected component.

(Default: –20 dBV)

11. Recording Input Terminal

Used for recording voice alarm messages.

(–60 dBV/2.2 kΩ or –20 dBV/10 kΩ selectable,

unbalanced, mini-jack)

12. Headphone Terminal

Connect headphones to this terminal to listen to

recorded messages for confirmation. Recorded

contents are output regardless of the settings of

the Mode Selector switch.

(0 dBV, 100 Ω, unbalanced, mini-jack)

13. Headphone Volume Control

Adjusts the volume of headphones.

19

21 22 23

15 16 18 1917

20

14

[Rear]

14. DC Power Input Terminal

Connect this terminal to 24 V DC power. Power

is supplied from the FS-7000PS Power Supply

Panel.

(M3 screw terminal; barrier distance: 6.4 mm)

15. Functional Earth Terminal

Connect this terminal to the functional earth

terminal of external equipment if excessive noise

is generated when the external equipment is

connected to the FS-7000EV. This could reduce

noise.

Note: This terminal is not for protective earth.

16. EV Audio Output Terminal

Connect this terminal to the FS-7000CP for

broadcasting evacuation announcements and

other voice alarms. Such alarms are output only

when the Mode Selector switch (5) is set to the

Normal position.

(0 dBV, 600 Ω, unbalanced, 2P terminal block)

17. USB Terminal

Connect this terminal to a PC or other equipment

using the USB cable. With this connection the

built-in sound source can be rewritten using

dedicated software.

18. USB Communication Indicator

Lights or flashes during USB communications.

19. Emergency ON Output Terminal

Activated during emergency broadcasts. This

terminal is connected to the FS-7006PA or FS-

7012PA amplifier to disable PA attenuators while

emergency announcements are being made.

(Relay output; rated voltage: 30 V DC; current

capacity: 1 A; 2P terminal block)

20. Emergency Control Contact Output Terminal

There are an output that is activated and an

output that is deactivated during emergency

announcements.

(Relay output; rated voltage: 30 V DC; current

capacity: 1 A; 3P terminal block)

21. Automatic Fire Alarm System Confirmation

Signal Input Terminal

Connect this terminal to a confirmation signal

(fire confirmation signal) from the automatic fire

alarm system. Evacuation announcements are

broadcast if they have not yet been initiated

when this signal is received.

[Open voltage: 24 V DC; short-circuit current: 6

mA, 2P terminal block (1 channel + COM)]

22. Emergency Power Control Terminal

Activates an emergency power supply unit

connected to the FS-7000PS in order to enable

emergency broadcasts during power failures.

Connect this terminal to the FS-7000PS.

Control input: Rated voltage: 24 V DC; current

capacity: 100 mA

Starting output: Open collector output; rated

voltage: 30 V DC; current capacity: 100 mA

(M3 screw terminal; barrier distance: 6.4 mm)

23. EV Control Terminal

Connect this terminal to the FS-7000CP Control

Panel.

20

5.7. FS-7000GM Group Matrix Panel

The FS-7000GM panel is used in conjunction with FS-7000 Series Voice Evacuation Systems to make group

broadcasts. The FS-7000GM connects to the FS-7000CP and FS-7000RF and enables group broadcasts by

selecting multiple speaker lines simultaneously via the zone selector keys on the FS-7000CP or FS-7000RM.

Up to 20 groups and 50 speaker lines can be made available per unit, which can be expanded to 20 groups

and 200 speaker lines by connecting 4 units.

[Front]

1

2 3 4 5 6

[Rear]

1. Power Indicator

Lights when power is supplied and the FS-

7000GM is ready for operation.

2. DC Power Input Terminal

Connect this terminal to 24 V DC power supply.

Power is supplied from the FS-7000PS.

(M3 screw terminal; barrier distance: 6.4 mm)

3. Functional Earth Terminal

Connect this terminal to the functional earth

terminal of external equipment if excessive noise

is generated when the external equipment is

connected to the FS-7000GM. This could reduce

noise.

Note: This terminal is not for protective earth.

4. GM Group Control Output Terminals

Used to increase the number of broadcast zones

that can be selected with a single group key by

connecting multiple FS-7000GM units. Connect

these terminals to other FS-7000GM unit.

5. GM Group Control Input Terminals

Use these terminals to change the zone selector

keys on the FS-7000CP into group selector keys

by connecting the FS-7000CP. These terminals

are also used to enable zone group selection from

the FS-7000RM by connecting the FS-7000RF. To

increase the number of zones that can be

selected simultaneously, connect these terminals

to other FS-7000GM's GM Group Control Output

Terminals (4).

6. GM Zone Control Terminals

Connect these terminals to the FS-7010CP and

FS-7000RF.

Page is loading ...

TOA FS-7010RM User manual

TOA FS-7010RM User manual

Related papers

Other documents