Crestron CEN-CI3-3 Installation guide

Brand: Crestron

Model: CEN-CI3-3

Type: Installation guide

CEN-CI3-3

3-Series

Card Interface - 3 Slot

Installation Guide

Description

The Crestron

CEN-CI3-3 is a single-space

rack-mountable enclosure designed to provide a

versatile control interface and expansion solution using

up to three 3-Series

Control Cards. It is used to

expand the control ports of a 3-Series Control System

Installation

The CEN-CI3-3 is designed to be placed on a shelf or

rack mounted using the included rack ears.

Mounting into a Rack

The CEN-CI3-3 occupies 1U of rack space. Using a #1

or #2 Phillips screwdriver, attach the two included rack

ears to the device. Then, mount the deivce into the rack

using four mounting screws (not included).

Additional Resources

Visit the product page on the

Crestron website

(www.crestron.com) for additional

information and the latest rmware

updates.

CAUTION: The CEN-CI3-3 should be used in a

well-ventilated area. The venting holes on the top and

sides should not be obstructed.

Mounting onto a Flat Surface

When placing the CEN-CI3-3 onto a at surface or

stacking it with other equipment, attach the included

feet near the corners on the underside of the

CEN-CI3-3.

Communicating with the Control Card

NOTE: The CEN-CI3-3 requires an IP address for the

chassis plus one for every card installed. If the

chassis is given a static address, each slot is

assigned a sequential address. (For example, if the

chassis IP address is x. x. x. 10, the card in slot 1 is

x.x.x.11, and the card in slot 2 is x.x.x.12. If there is

no card in slot 1, the card in slot 2 is still x.x.x.12.)

NOTE: Although the cards get IP addresses, they do

not appear in the Device Discovery Tool in Crestron

Toolbox™. Use the Network Device Tree Tool to view

the IP settings of all installed cards.

Only the chassis gets an IP table entry.

NOTE: The CONTROL SUBNET ports work with

LANs as well as with control subnet networks. The

CONTROL SUBNET out port can be used for daisy

chaining.

Crestron Electronics, Inc. Installation Guide

15 Volvo Drive DOC. 7793A

Rockleigh, NJ 07647 (2043973)

Tel: 888.CRESTRON 05.15

Fax: 201.767.7576 Specications subject to

www.crestron.com change without notice.

As of the date of manufacture, the CEN-CI3-3 has been

tested and found to comply with specications for CE

marking.

This product is Listed to applicable UL Standards and

requirements by Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance

Statement

This device complies with part 15 of the FCC Rules.

Operation is subject to the following conditions: (1) This

device may not cause harmful interference and (2) this device

must accept any interference received, including interference

that may cause undesired operation.

CAUTION: Changes or modications not expressly

approved by the manufacturer responsible for compliance

could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and

receiver

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV

technician for help

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The product warranty can be found at

www.crestron.com/warranty.

The specic patents that cover Crestron products are listed at

patents.crestron.com.

Crestron, the Crestron logo, 3-Series, and 3-Series Control

System are either trademarks or registered trademarks of

Crestron Electronics, Inc. in the United States and/or other

countries. UL and the UL logo are either trademarks or

registered trademarks of Underwriters Laboratories, Inc. in

the United States and/or other countries. Other trademarks,

registered trademarks, and trade names may be used in this

document to refer to either the entities claiming the marks

and names or their products. Crestron disclaims any

proprietary interest in the marks and names of others.

Crestron is not responsible for errors in typography or

photography.

This document was written by the Technical Publications

department at Crestron.

Crestron CEN-CI3-3 Installation guide

Crestron CEN-CI3-3 Installation guide

Crestron CEN-CI3-3 Installation guide

Related papers

Other documents