ProForm PETL40706 Owner's manual

Brand: ProForm

Model: PETL40706

Category: Treadmills

Type: Owner's manual

USER'S MANUAL

Model No. PETL40706.0

erial No.

CAUTION

Read all precautions and instruc

tions in this manual before using

this equipment. Save this manual

for future reference.

Serial Number

Decal

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if there are

missing or damaged parts,

please call:

or write:

ICON Health & Fitness, Ltd.

Customer Service Department

Unit 4

Revie Road Industrial Estate

Revie Road

Beeston

Leeds, LS118JG

email: [email protected]

08457 089 009

TABLE OF CONTENTS

MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

PROFORM is a registered trademark of ICON IP, Inc.

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

2. Use the treadmill only as described.

3. Place the treadmill on a level surface, with at

least 2.5 m (8 ft.) of clearance behind it and

0.5 m (2 ft.) on each side. Do not place the

treadmill on a surface that blocks any air

openings. To protect the floor or carpet from

damage, place a mat under the treadmill.

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should be used only by persons

weighing 136 kg (300 lbs.) or less.

8. Never allow more than one person on the

treadmill at a time.

9. Wear appropriate exercise clothes when

using the treadmill. Do not wear loose clothes

that could become caught in the treadmill.

Athletic support clothes are recommended for

both men and women.

Always wear athletic

shoes; never use the treadmill with bare feet,

wearing only stockings, or in sandals.

10.

When connecting the power cord (see page

11), plug the power cord into an earthed cir-

cuit. No other appliance should be on the

same circuit. When replacing the fuse, an

ASTA approved BS1362 type should be fitted

to the fuse carrier. A 13 amp fuse should be

used.

11. Keep the power cord away from heated sur-

faces.

12. Never move the walking belt while the power

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See TROU-

BLESHOOTING on page 26 if the treadmill is

not working properly.)

13. Read, understand, and test the emergency

stop procedure before using the treadmill (see

HOW TO TURN ON THE POWER on page 13).

14. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the

handrails while using the treadmill.

15. The treadmill is capable of high speeds.

Adjust the speed in small increments to avoid

sudden jumps in speed.

16. The pulse sensor is not a medical device.

Various factors, including your movement,

may affect the accuracy of heart rate readings.

The sensor is intended only as an exercise aid

in determining heart rate trends in general.

17. Never leave the treadmill unattended while it

is running. Always remove the key and unplug

the power cord when the treadmill is not in

use.

18. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 6, and HOW TO FOLD

AND MOVE THE TREADMILL on page 24.)

You must be able to safely lift 20 kg (45 lbs.) to

raise, lower, or move the treadmill.

19. When folding or moving the treadmill, make

sure that the storage latch is fully engaged.

20.

When using iFIT.com programs, an electronic

“chirping” sound will alert you when the

speed and/or incline of the treadmill is about

to change. Always listen for the “chirp” and

be prepared for speed and/or incline changes.

In some instances, the speed and/or incline

may change before the personal trainer de-

scribes the change.

WARNING: T

o reduce the risk of burns, fire, electric shock, or injury to persons, read the

following important precautions and information before operating the treadmill.

IMPORTANT PRECAUTIONS

21. When using iFIT.com programs, you can

manually override the speed and incline set-

tings by pressing the speed and incline but-

ons. However, when the next “chirp” is

heard, the speed and/or incline will change

to the next settings of the CD or video pro-

gram.

22. Always remove iFIT.com CDs and videos

from your CD player or VCR and disconnect

your MP3 player when you are not using

them.

23. Inspect and properly tighten all parts of the

treadmill regularly.

24. Never insert any object into any opening.

25.

DANGER: Always unplug the power

cord immediately after use, before cleaning

he treadmill, and before performing the

maintenance and adjustment procedures de-

scribed in this manual. Never remove the

motor hood unless instructed to do so by an

authorized service representative. Servicing

other than the procedures in this manual

should be performed by an authorized ser-

vice representative only.

26. This treadmill is intended for in-home use

only. Do not use this treadmill in a commer-

cial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

The decals shown at the right have been placed on the treadmill. If a decal is miss-

ing, or if it is illegible, call the telephone number on the front cover of this manual

and order a free replacement decal. Apply the decal in the location shown. Note:

The decals are not shown at actual size.

hank you for selecting the new PROFORM

85 CX

readmill. The 485 CX treadmill combines advanced

technology with innovative design to help you get the

most from your exercise in the convenience of your

home. And when you’re not exercising, the 485 CX

treadmill can be folded up, requiring less than half the

floor space of other treadmills.

For your benefit, read this manual carefully before

using the treadmill. If you have questions after read-

ng this manual, please see the front cover of this man-

al. To help us assist you, please note the product

model number and serial number before contacting us.

The model number of the treadmill is PETL40706.0

The serial number can be found on a decal attached to

the treadmill (see the front cover of this manual for the

location).

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

BEFORE YOU BEGIN

Handrail

Storage Latch

Key/Clip

Circuit Breaker

On/Off Switch

Walking Belt

Cushioned Walking Platform

for maximum exercise comfort

Foot Rail

RIGHT SIDE

Rear Roller

Adjustment Bolts

Console

Accessory Tray

Handgrip Pulse Sensor

BACK

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not

dispose of the packing materials until assembly is completed. Note: The underside of the walking belt is coated

with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the

walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there

is lubricant on top of the walking belt, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex keys, your own phillips screwdriver , and your

own rubber mallet .

For help identifying the assembly hardware, see the drawings below.

The number in parentheses below each

drawing is the key number of the part, from the PART LIST on pages 30 and 31. The number following the paren-

theses is the quantity needed for assembly.

Note: If a part is not in the parts bag, check to see if it has been

pre-assembled. To avoid damaging plastic parts, do not use power tools for assembly.

1/2" Screw

(33)–1

Handrail Bolt/Extension Leg Bolt (64)–8

Star Washer

(8)–10

Screw (3)–15

1" Tek Screw

(22)–4

Long Handrail Bolt (106)–2

1. Make sure that the power cord is unplugged.

With the help of a second person, carefully tip

the treadmill onto its left side as shown. Partially

fold the Frame (58) so the treadmill is more sta-

ble. Do not fully fold the treadmill until it is

completely assembled.

Insert an Extension Leg (89) into the base of the

Uprights (84) as shown. Note: Be careful not to

pinch the Upright Wire Harness (77) in the

base of the Upright. To fully insert the

Extension Leg, it may be necessary to tap on it

with a mallet. Next, insert two Extension Leg

Bolts (64) with two Star Washers (8) into the bot

tom of the Extension Leg, and firmly tighten the

Extension Leg Bolts.

Attach two Base Pads (82) to the base of the

Uprights (84) with two 1" Tek Screws (22).

2. With the help of a second person, carefully tip

the treadmill onto its right side. Partially fold the

rame (58) so the treadmill is more stable. D

not fully fold the treadmill until it is com-

letely assembled.

Insert the other Extension Leg (89) into the base

of the Uprights (84) as shown. Next, insert two

Extension Leg Bolts (64) with two Star Washers

(8) into the bottom of the Extension Leg, and

firmly tighten the Extension Leg Bolts.

Attach two Base Pads (82) to the base of the

Uprights (84) with two 1" Tek Screws (22).

With the help of a second person, carefully raise

the treadmill so that all four Base Pads (82) are

on the floor and the Uprights (84) are in a verti-

cal position.

3. Lay the Left Handrail (103) on the floor. Slide the

left end of the Crossbar (20) onto the tab on the

Left Handrail and start two Screws (3) into the

Crossbar and the tab. Do not tighten the

Screws yet.

Slide the tab on the Right Handrail (104) into the

right side of the Crossbar (20) and start two

Screws (3) into the Crossbar and the tab. Do not

tighten the Screws yet.

103

104

Tab

4. Have a second person hold the Handrails (103,

104) near the Uprights (84). Insert the Upright

Wire Harness (77) through the large holes in the

Right Handrail as shown.

Next, set the Handrails (103, 104) on the

Uprights (84).

Do not let the Upright Wire

Harness (77) fall into the right Handrail.

Attach the Handrails (103, 104) to the Uprights

(84) with four Handrail Bolts (64) and four Star

Washers (8); start all four Handrail Bolts but

do not tighten them.

103

104

Large Holes

6. While a second person holds the console as-

sembly near the Left Handrail (103), attach the

ground wire to the indicated hole in the Left

Handrail with a 1/2" Screw (33).

103

Hole

Ground

Wire

Console

Assembly

7. While the second person continues to hold the

console assembly, locate the console wire har-

ness on the back of the console assembly.

Connect the console wire harness to the Upright

Wire Harness (77).

Make sure to connect the

connectors properly (see the inset drawing).

The connectors should slide together easily

and snap into place. If the connectors do not

slide together easily and snap into place, turn

one connector and then try again. IF THE CON-

NECTORS ARE NOT CONNECTED PROP-

ERLY, THE CONSOLE MAY BE DAMAGED

WHEN THE POWER IS TURNED ON.

Then, insert the connectors down into the Right

Handrail (104).

Console

Assembly

104

Console Wire

Harness

5. Attach the lower ends of the Handrails (103,

04) to the Uprights (84) with two Long Handrail

Bolts (106) and two Star Washers (8);

start both

Handrail Bolts and then firmly tighten them.

irmly tighten the four Handrail Bolts (64) (only

two are shown)

See step 3. Firmly tighten the four Screws (3).

106

103

104

106

9. Hand tighten four additional Screws (3) into the

console assembly. Then, tighten all nine

Screws used in step 8 and this step; do not

overtighten the Screws.

Console Assembly

10. Attach the Latch Housing (73) to the left Upright

(84) with two Screws (3). Make sure that the

large hole in the Latch Housing is on the

side shown. Do not overtighten the Screws.

If the pin is not preassembled in the Latch

Housing (73), remove the knob from the pin.

Make sure that the collar and the spring are on

the pin as shown. Insert the pin into the Latch

Housing, and tighten the knob back onto the pin.

Plug in the power cord as described on page 11,

and turn on the power as described on page 13.

Note: The treadmill may automatically rise to the

maximum incline level and then return to the

minimum level.

Knob

Collar

Large

Hole

Spring

8. Set the console assembly on the Crossbar (20).

Be careful to avoid pinching any of the wires.

ake sure that the ground wire (see step 6)

and the console wire harness (see step 7) are

nside the indicated channel.

Hand tighten five Screws (3) into the Crossbar

(20) and the console assembly. Start all five

Screws, but do not tighten them yet. Do not

put Screws into the two indicated holes.

Console Assembly

No Screws

Channel

13. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may

be included. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt

(see page 27). To protect the floor or carpet, place a mat under the treadmill.

12.Raise the Shock (92) to a vertical position.

Remove the Shock Pin (25) from the raised end

of the Shock as described in step 11. If neces-

sary, rotate the Shock to align the end of the

Shock with the ball on the bracket on the Frame

(58).

Next, press the Incline increase and decrease

buttons until the ball on the bracket is aligned

with end of the Shock (92). Then, press the end

of the Shock onto the ball. Note: It may be nec-

essary to press the end of the Shock onto the

ball while the Frame is moving.

See drawing 12a. Insert the Shock Pin (25) into

the two indicated small holes in the end of the

Shock (92). Then, rotate the Shock Pin until it

clips onto the Shock. Note: Extra Shock Pins are

included.

Press the Incline decrease button until the

treadmill is at the lowest incline level. Then,

unplug the power cord and lower the treadmill

Frame (58) to the floor.

Holes

12a

Bracket

11.Place the treadmill in the storage position (see

HOW TO FOLD AND MOVE THE TREADMILL

n page 24).

ext, place the cylinder end of the Shock (92)

near the bracket on the base of the Uprights

(84).

See the two small inset drawings. Using your fin-

gernail or the end of a screwdriver, press on the

end of the Shock Pin (25) to loosen it from the

Shock (92). Next, rotate the Shock Pin and pull it

out of the Shock.

Be careful to avoid losing

the Shock Pin.

See drawing 11a. Press the cylinder end of the

Shock (92) onto the ball on the bracket. Next, in-

sert the end of the Shock Pin (25) through two of

the small holes in the end of the Shock. Then,

rotate the Shock Pin until it clips onto the Shock.

11a

Bracket

Cylinder

Bracket

THE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply sili-

cone spray or other substances to the walking belt or the walking platform. Such substances will deterio-

rate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

This product must be earthed. If it should malfunction or break

down, earthing provides a path of least resistance for electric cur-

rent to reduce the risk of electric shock. This product is equipped

with a power cord having an equipment-earthing conductor and an

earthing plug.

Important: If the power cord is damaged, it must

be replaced with a manufacturer-recommended power cord.

See drawing 1. Plug the indicated end of the power cord into the

socket on the treadmill.

See drawing 2. Press the pins on the power cord into the metal clips

in the adapter as shown. Close the adapter cover over the end of the

power cord and tighten the screw in the adapter.

Important: Make

sure that the adapter cover is secure and the screw has been

tightened before using the power cord.

See drawing 3. Plug the power cord into an appropriate outlet that is

properly installed and earthed in accordance with all local codes and

ordinances. Important: The treadmill is not compatible with

GFCI-equipped outlets.

DANGER: Improper connection of the equipment-earthing conductor can result in an in-

creased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as

to whether the product is properly earthed. Do not modify the plug provided with the product—if it will

not fit the outlet, have a proper outlet installed by a qualified electrician.

Socket on treadmill

Metal

Clips

Pins

Screw

Adapter

Outlet

Adapter

Cover

OPERATION AND ADJUSTMENT

FEATURES OF THE CONSOLE

The treadmill console offers a selection of features

designed to make your workouts more effective. When

you select the manual mode of the console, you can

change the speed and incline of the treadmill with the

touch of a button. As you exercise, the console will

display continuous exercise feedback. You can even

measure your heart rate using the handgrip pulse sen-

sor or the optional chest pulse sensor (see page 23).

The console also features ten trainer programs. Each

trainer program automatically controls the speed and

incline of the treadmill as it guides you through an ef-

fective workout. In addition, the console offers two

heart rate programs. Each heart rate program adjusts

the speed and incline of the treadmill to keep your heart

rate near a target heart rate during your workout. Note:

You must wear the optional chest pulse sensor to use

the heart rate programs.

The console also features iFIT.com interactive technol-

ogy. Having iFIT.com technology is like having a per

sonal trainer in your home. Using a stereo audio cable,

you can connect the treadmill to your portable stereo,

home stereo, computer, or VCR and play special

iFIT.com MP3, CD, and video programs (iFIT.com MP3

programs, CDs, and videocassettes are available sepa-

rately). iFIT.com programs automatically control the

speed and incline of the treadmill as a personal trainer

guides you through every step of your workout; high-

energy music provides added motivation.

To down-

load iFIT.com MP3 programs, go to www.iFIT.com.

To purchase iFIT.com CDs or videocassettes, call

the telephone number on the front cover of this

manual.

With the treadmill connected to your computer, you

can also go to www.iFIT.com and access iFIT.com

programs directly from our Web site. See

www.iFIT.com for more information.

To use the manual mode of the console, follow the

steps beginning on page 13. To use a trainer

program, see page 15. To use a heart rate program,

see page 16. To use an iFIT.com MP3, CD, or video

program, see page 20. To use an iFIT.com

program

directly from our Web site, see page 22.

Clip

CONSOLE DIAGRAM

Note: If there is a sheet of clear plastic

on the face of the console, remove it.

Key

HOW TO TURN ON THE POWER

lug in the power cord

(see page 11). Next, lo-

ate the on/off switch near

the power cord. Make sure

that the switch is in the

“on” position.

Next, stand on the foot rails of the treadmill. Find the

clip attached to the key (see the drawing on page 12)

and slide the clip onto the waistband of your clothes.

Then, insert the key into the console. After a moment,

the display will light.

Important: In an emergency sit-

uation, the key can be pulled from the console,

causing the walking belt to slow to a stop. Test the

clip by carefully taking a few steps backward; if the

key is not pulled from the console, adjust the posi-

tion of the clip.

HOW TO USE THE MANUAL MODE

Insert the key into the console.

See HOW TO TURN ON THE POWER above.

Select the manual mode.

When you

insert the

key, the

manual

mode will be

selected. If

you have

selected a program, reselect the manual mode by

pressing the Heart Rate Programs button repeat

edly until a track appears in the display.

Start

the walking belt.

To start the walking belt, press the Start button,

the Speed increase button, or one of the speed

buttons numbered 2 through 18.

If you press the Start button or the Speed in-

crease button, the walking belt will begin to move

at 2 km/h. As you exercise, change the speed of

the walking belt as desired by pressing the Speed

increase and decrease

buttons. Each time you

ress a button, the

speed setting will

hange by 0.1 km/h; if

you hold down a button,

the speed setting will change in increments of 0.5

km/h. Note: After you press the buttons, it may take

a moment for the walking belt to reach the selected

speed setting.

If you press one of the numbered speed buttons,

the walking belt will gradually change in speed until

it reaches the selected speed setting.

To stop the walking belt, press the Stop button.

The time will begin to flash in the display. To

restart the walking belt, press the Start button, the

Speed increase button, or one of the numbered

speed buttons.

Note: The first time the treadmill is used, observe

the alignment of the walking belt, and center the

walking belt if necessary (see page 27).

Change the incline of the treadmill as desired.

To change the incline of

the treadmill, press the

Incline increase and de-

crease buttons. Each

time you press a button,

the incline will change by

0.5%. Note: After you press the buttons, it may

take a moment for the treadmill to reach the se-

lected incline setting.

Follow your progress with the display.

When the

manual mode

is selected,

the display

will show a

track that

represents

400 meters (1/4 mile). As you walk or run, the indi-

cators around the track will appear in succession

until the entire track appears. The track will then

disappear and the indicators will again begin to ap-

pear in succession.

Track

Position

Track

The left side of the dis-

play will show the

lapsed time, the dis-

tance that you have

alked or run, and the

incline level of the tread-

mill. Note: When a program is selected (except for

heart rate program 2), the display will show the

time remaining in the program instead of the

elapsed time.

The right side of the

display will show the

approximate number of

calories you have

burned, the speed of

the walking belt, and

your pace (in minutes per kilometer). The right side

of the display will also show your heart rate when

you use the handgrip pulse sensor or the optional

chest pulse sensor.

Note: The console can display speed and dis-

tance in either kilometers or miles. To find which

unit of measurement is selected, or to change the

unit of measurement, see THE INFORMATION

MODE on page 23.

Note: For simplicity, all in-

structions in this section refer to kilometers.

To reset the display, press the Stop button, re-

move the key, and then reinsert the key.

Measure your heart rate if desired.

Note: If you

use the

handgrip

pulse sensor

and the op-

tional chest

pulse sensor

at the same

time, the

console will not display your heart rate accurately.

Before using the handgrip pulse sensor, remove

the sheets of clear plastic from the metal contacts.

In addition, make sure that your hands are clean.

To measure your heart rate, stand on the foot

rails and hold the metal contacts on the

andrail—a

void moving your hands

When your

pulse is detected, the heart symbol in the right side

f the display will begin to flash each time your

heart beats, one or two dashes will appear, and

then your heart rate will be shown.

For the most

accurate heart rate reading, continue to hold

the contacts for about 15 seconds.

Turn on the fan if desired.

To turn on the fan, press the Fan button. To turn

on the fan at high speed, press the button a sec-

ond time. To turn off the fan, press the button a

third time. Note: If the fan is left on when the walk-

ing belt is stopped, the fan will automatically turn

off after a few minutes.

When you are finished exercising, remove the

key.

Step onto the foot rails, press the Stop button, and

adjust the incline of the treadmill to the lowest

setting. The incline must be at the lowest setting

when you fold the treadmill to the storage posi-

tion you will damage the treadmill. Next, remove

the key from the console and put it in a secure

place. Note: If the display remains lit after the

key is removed, the console is in the “demo”

mode. See page 23 and turn off the demo mode.

When you are finished using the treadmill,

switch the on/off switch to the “off” position

and unplug the power cord.

Contacts

OW TO USE A TRAINER PROGRAM

nsert the key into the console.

See HOW TO TURN ON THE POWER on page

13.

Select a trainer program.

To select

one of the

trainer pro-

grams,

press the

Trainer

Programs

button re

peatedly

until one of the program indicators (“P1” through

“P10”) appears in the display. When a trainer pro-

gram is selected, the program time will appear in

the display, the maximum incline setting of the

program and the maximum speed setting of the

program will flash in the display for a few seconds,

and a profile of the speed settings of the program

will scroll across the display.

Press the Start button or the Speed increase

button to start the program.

A moment after you press the button, the treadmill

will automatically adjust to the first speed and in-

cline settings of the program. Hold the handrails

and begin walking.

Each program is divided into 30, 50, or 60 one-

minute segments. One speed setting and one in-

cline setting are programmed for each segment.

Note: The same speed setting and/or incline setting

may be programmed for two or more consecutive

segments.

The speed

setting for

the first seg-

ment will be

shown in

the flashing

Current

Segment column of the display. (The incline set

tings are not shown in the upper part of the dis-

play.) The speed settings for the next several seg-

ments will be shown in the columns to the right.

When only three seconds remain in the first seg-

ent of the program, both the Current Segment

column and the column to the right will flash and a

series of tones will sound. If the speed and/or in-

cline of the treadmill is about to change, the speed

setting and/or the incline setting will flash in the

display to alert you.

When the first segment is completed,

all speed

settings will move one column to the left

. The

speed setting for the second segment will then be

shown in the flashing Current Segment column

and the treadmill will automatically adjust to the

speed and incline settings for the second seg-

ment. Note: If all of the indicators in the Current

Segment column are lit,

the speed settings may

move downward

so that only the highest indicators

appear in the display.

The program will continue in this way until the

speed setting for the last segment is shown in the

Current Segment column and the last segment

ends. The walking belt will then slow to a stop.

If the speed or incline setting for the current seg-

ment is too high or too low, you can manually

override the setting by pressing the Speed or

Incline buttons. Every few times a Speed button is

pressed, an additional indicator will appear or dis-

appear in the Current Segment column; if any of

the columns to the right of the Current Segment

column have the same number of lit indicators as

the Current Segment column, an additional indica-

tor may appear or disappear in those columns as

well.

Important: When the current segment

ends, the treadmill will automatically adjust to

the speed and incline settings for the next seg

ment.

To stop the program at any time, press the Stop

button. The time will begin to

flash in the display.

To restart the program, press the Start

button or

the Speed increase button. The walking belt will

begin to move at 2 km/h. When the next segment

of the program begins, the treadmill will automati-

cally adjust to the speed and incline settings for the

next segment.

Current Segment

ollow your progress with the display.

See step 5 on page 13.

Measure your heart rate if desired.

See step 6 on page 14.

Turn on the fan if desired.

See step 7 on page 14.

When you are finished exercising, remove the

key from the console.

See step 8 on page 14.

OW TO USE A HEART RATE PROGRAM

Heart rate program 1 will automatically adjust the speed

and incline of the treadmill to keep your heart rate within

a preset range during your workout. Heart rate program

2 will keep your heart rate near a target heart rate setting

that you select.

Follow the steps below to use a heart rate program.

Put on the optional chest pulse sensor.

See the instructions included with the chest pulse

sensor.

Insert the key into the console.

See HOW TO TURN ON THE POWER on page

13.

Select a heart rate program.

To select a heart rate program, press the Heart

Rate Programs button repeatedly until “P1” or

“P2” appears in the display.

If heart rate

program 1

is selected,

a profile of

the target

heart rate

settings of

the program

will scroll

across the display.

If heart rate program 2 is selected, a graphic

representing your heartbeat will appear in the dis

play.

CAUTION: If you have heart prob-

lems, or if you are over 60 years of age and

have been inactive, do not use the heart rate

programs. If you are taking medication regu-

larly, consult your physician to find whether the

medication will affect your exercise heart rate.

nter a target heart rate setting.

If heart rate program 1

is selected,

the maxi-

mum target heart rate

setting of the program

will appear in the display.

f desired, press the in-

crease and decrease buttons beside the Heart

Rate Programs button to change the maximum

target heart rate setting (see EXERCISE INTEN-

SITY on page 28).

Note: If you change the maxi-

mum target heart rate setting, the intensity level of

the entire program will change.

If heart rate program 2 is selected, the target

heart rate setting for the program will be dis-

played. If desired, press the increase and de-

crease buttons beside the Heart Rate Programs

button to change the target heart rate setting

(see

EXERCISE INTENSITY on page 28).

Note: The

same target heart rate setting will be programmed

for the entire program.

Press the Start button or the Speed increase

button to start the program.

A moment after you press the button, the treadmill

will automatically adjust to the first speed and in-

cline settings of the program. Hold the handrails

and begin walking.

Heart rate program 1 is divided into 30 one-minute

segments. One target heart rate setting is pro-

grammed for each segment. (Note: The same tar-

get heart rate setting may be programmed for two

or more consecutive segments.) Heart rate pro-

gram 2 is divided into 100 one-minute segments.

The same target heart rate setting is programmed

for all segments. Note: For a shorter workout, sim

ply stop the program before it ends.

If heart rate

program 1 is

selected, the

target heart

rate setting

for the first

segment will

be shown in the flashing Current Segment column

of the display.

The target heart rate settings for the

next several segments will be shown in the

columns to the right. When only three seconds re

main in the first segment, both the Current

Segment column and the column to the right will

flash and a series of tones will sound. When the

first segment ends,

all target heart rate settings

ill move one column to the left.

he target heart

rate setting for the second segment will then be

hown in the flashing Current Segment column.

During both heart rate programs, the console will

regularly compare your heart rate to the current

target heart rate setting. If your heart rate is too

far below or above the target heart rate setting,

the speed of the walking belt will automatically in-

crease or decrease to bring your heart rate closer

to the target heart rate setting. If the speed of the

walking belt reaches 12 km/h and your heart rate

is still too far below the target heart rate setting,

the incline of the treadmill will also increase.

If the speed or incline setting is too high or too low

at any time during the program, you can adjust the

setting with the Speed or Incline buttons. However,

each time the console compares your heart rate to

the target heart rate setting, the speed and/or in-

cline of the treadmill may automatically change to

bring your heart rate closer to the target heart rate

setting.

If your pulse is not detected during the program,

the letters “PLS” will flash in the display and the

speed and/or incline of the treadmill may automat-

ically decrease.

To stop the program at any time, press the Stop

button. The time will begin to flash in the display.

To restart the program, press the Start button or

the Speed increase button. The walking belt will

begin to move at 2 km/h. When the console com-

pares your heart rate to the target heart rate set-

ting, the speed and/or incline of the treadmill may

automatically change to bring your heart rate

closer to the target heart rate setting.

Follow your progress with the display.

See step 5 on page 13.

Turn on the fan if desired.

See step 7 on page 14.

When you are finished exercising, remove the

key from the console.

See step 8 on page 14.

Current Segment

HOW TO CONNECT THE TREADMILL TO USE

IFIT.COM PROGRAMS

To use iFIT.com MP3 or CD programs

, you must

onnect the treadmill to your MP3 player, CD player,

ortable stereo, home stereo, or computer. See pages

18 and 19 for connecting instructions. To use iFIT.com

programs directly from our Web site, you must con-

nect the treadmill to your computer. See page 19 for

connecting instructions.

To use iFIT.com video pro-

grams

, you must connect the treadmill to your VCR.

See page 20 for connecting instructions.

HOW TO CONNECT YOUR MP3 PLAYER OR CD

PLAYER

A. Plug one end of the included 3.5 mm to 3.5 mm

stereo audio cable into the input jack on the con-

sole. Plug the other end of the cable into a jack on

your MP3 player or CD player. Plug your head-

phones into the headphone jack on the console.

HOW TO CONNECT YOUR PORTABLE STEREO

ote: If your stereo has an RCA-type AUDIO OUT

jack, see instruction A below. If your stereo has a

.5 mm LINE OUT jack, see instruction B. If your

stereo has only a PHONES jack, see instruction C.

A. Plug one end of a long 3.5 mm to RCA stereo audio

cable (available at electronics stores) into the input

jack on the console. Plug the other end of the cable

into the AUDIO OUT jack on your stereo.

B. See the drawing above. Plug one end of a long 3.5

mm to 3.5 mm stereo audio cable (available at elec-

tronics stores) into the input jack on the console.

Plug the other end of the cable into the LINE OUT

jack on your stereo. Note: While the cable is

plugged into the LINE OUT jack, do not plug your

headphones into the headphone jack on the con-

sole.

C. Plug one end of a long 3.5 mm to 3.5 mm stereo

audio cable (available at electronics stores) into the

input jack on the console. Plug the other end of the

cable into the PHONES jack on your stereo. Plug

your headphones into the headphone jack on the

console.

LINE OUT

PHONES

INE OUT

PHONES

Audio

Cable

Headphones

AUDIO OUT

IGHT

LEFT

LINE OUT

Audio Cable

A/B

PHONES

Audio

Cable

Headphones

HOW TO CONNECT YOUR HOME STEREO

ote: If your stereo has an unused LINE OUT jack,

see instruction A below. If the LINE OUT jack is

eing used, see instruction B.

A. Plug one end of a long 3.5 mm to RCA stereo audio

cable (available at electronics stores) into the input

jack on the console. Plug the other end of the cable

into the LINE OUT jack on your stereo. Note: While

the cable is plugged into the LINE OUT jack, do not

plug your headphones into the headphone jack on

the console.

B. Plug one end of a long 3.5 mm to RCA stereo audio

cable (available at electronics stores) into the input

jack on the console. Plug the other end of the cable

into an RCA Y-adapter (available at electronics

stores). Next, remove the wire that is currently

plugged into the LINE OUT jack on your stereo and

plug the wire into the unused side of the Y-adapter.

Plug the Y-adapter into the LINE OUT jack on your

stereo. Note: While the Y-adapter is plugged into the

LINE OUT jack, do not plug your headphones into

the headphone jack on the console.

HOW TO CONNECT YOUR COMPUTER

. Plug one end of a long 3.5 mm to 3.5 mm stereo

audio cable (available at electronics stores) into the

nput jack on the console. Plug the other end of the

cable into the LINE OUT jack on your computer.

Note: While the cable is plugged into the LINE OUT

jack, do not plug your headphones into the head-

phone jack on the console.

VCR

Amp

INE OUT

LINE OUT

Audio Cable

VCR

Amp

LINE OUT

Audio

Cable

RCA

Y-adapter

Wire removed from

LINE OUT jack

LINE OUT

Audio Cable

HOW TO CONNECT YOUR VCR

ote: If your VCR has an unused AUDIO OUT jack,

see instruction A below. If the AUDIO OUT jack is

eing used, see instruction B. If you have a TV

with a built-in VCR, see instruction B. If your VCR

is connected to your home stereo, see HOW TO

CONNECT YOUR HOME STEREO on page 19.

A. Plug one end of a long 3.5 mm to RCA stereo audio

cable (available at electronics stores) into the input

jack on the console. Plug the other end of the cable

into the AUDIO OUT jack on your VCR.

B. Plug one end of a long 3.5 mm to RCA stereo audio

cable (available at electronics stores) into the input

jack on the console. Plug the other end of the cable

into an RCA Y-adapter (available at electronics

stores). Next, remove the wire that is currently

plugged into the AUDIO OUT jack on your VCR and

plug the wire into the unused side of the Y-adapter.

Plug the Y-adapter into the AUDIO OUT jack on

your VCR.

HOW TO USE AN IFIT.COM MP3, CD, OR VIDEO

PROGRAM

To use an iFIT.com MP3, CD, or video program, you

ust connect the treadmill to your MP3 player, CD

layer, or VCR. See HOW TO CONNECT THE

TREADMILL TO USE IFIT.COM PROGRAMS on

pages 18 to 20. To download iFIT.com MP3 pro-

grams, go to www.iFIT.com. To purchase iFIT.com

CDs or videocassettes, call the telephone number

on the front cover of this manual.

Follow the steps below to use an iFIT.com MP3, CD,

or video program.

Insert the key into the console.

See HOW TO TURN ON THE POWER on page 13.

Select the iFIT.com mode.

To select the

iFIT.com

mode, press

the iFIT but-

ton. The let-

ters “iFIT”

will appear

in the display.

Press the Play button on your MP3 player, CD

player, or VCR.

Note: If you are using an iFIT.com CD, insert the

CD into your CD player; if you are using an

iFIT.com videocassette, insert the videocassette

into your VCR.

A moment after the Play button is pressed, your

personal trainer will begin guiding you through

your workout. Simply follow your personal trainer’s

instructions. Note: If the time is flashing in the dis-

play, press the Start button or the Speed increase

button on the console. The treadmill will not re

spond to an MP3, CD, or video program while the

time is flashing in the display.

During the program, an electronic “chirping” sound

will alert you when the speed and/or incline of the

treadmill is about to change. CAUTION: Always

listen for the “chirp” and be prepared for speed

and/or incline changes. In some instances, the

speed and/or incline may change before your

personal trainer describes the change.

AUDIO OUT

RIGHT

LEFT

VIDEO AUDIO

ANT. IN

F OUT

OUT

Audio Cable

VIDEO AUDIO

ANT. IN

RF OUT

OUT

Wire removed from

AUDIO OUT jack

RCA

Y-adapter

Audio Cable

Page is loading ...

ProForm PETL40706 Owner's manual

Brand: ProForm

Model: PETL40706

Category: Treadmills

Type: Owner's manual

Download PDF

report

ProForm PETL40706 Owner's manual

ProForm PETL40706 Owner's manual

Related papers

Other documents