Grizzly T26470 Owner's manual

Brand: Grizzly

Model: T26470

Category: Hand tools supplies

Type: Owner's manual

Grizzly T26470 is a benchtop Hand Shear designed to cut light-gauge sheet metal. A stationary blade is mounted to the machine base and a moving blade is connected to the handles. When the handles are pulled down, the upper blade moves past the lower stationary blade, creating a shearing action, similar to a pair of scissors. The Model T26470 is equipped with a rear adjustable work stop for making repetitive cuts of the same length.

MODEL T26470

HAND SHEAR

OWNER'S MANUAL

(For models manufactured since 01/14)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#DM16261 PRINTED IN CHINA

V1.03.14

This manual provides critical safety instructions on the proper setup,

operation, maintenance, and service of this machine/tool. Save this

document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual

may result in fire or serious personal injury—including amputation,

electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.

This responsibility includes but is not limited to proper installation in

a safe environment, personnel training and usage authorization,

proper inspection and maintenance, manual availability and compre-

hension, application of safety devices, cutting/sanding/grinding tool

integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage

from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State

of California to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

Work in a well ventilated area, and work with approved safety equip-

ment, such as those dust masks that are specially designed to filter

out microscopic particles.

INTRODUCTION ............................................................................................................................... 2

Machine Description ................................................................................................................... 2

Contact Info ................................................................................................................................ 2

Manual Accuracy ........................................................................................................................ 2

Identification ............................................................................................................................... 3

Machine Data Sheet ................................................................................................................... 4

SECTION 1: SAFETY ....................................................................................................................... 5

Safety Instructions for Machinery ............................................................................................... 5

Additional Safety for Shear Machines ........................................................................................ 7

SECTION 2: SETUP ......................................................................................................................... 8

Unpacking .................................................................................................................................. 8

Needed for Setup ....................................................................................................................... 8

Inventory ..................................................................................................................................... 8

Cleanup ...................................................................................................................................... 9

Site Considerations .................................................................................................................... 9

Bench Mounting ....................................................................................................................... 10

Assembly .................................................................................................................................. 11

SECTION 3: OPERATIONS ........................................................................................................... 12

Cutting Sheet Metal .................................................................................................................. 12

Work Stop................................................................................................................................. 13

SECTION 4: ACCESSORIES ......................................................................................................... 14

SECTION 5: MAINTENANCE......................................................................................................... 17

Schedule .................................................................................................................................. 17

Cleaning ................................................................................................................................... 17

Lubrication ................................................................................................................................ 17

SECTION 6: SERVICE ................................................................................................................... 18

Troubleshooting ........................................................................................................................ 18

Adjusting Blade Bow ................................................................................................................ 19

Sharpening/Replacing Blades .................................................................................................. 20

SECTION 7: PARTS ....................................................................................................................... 21

Main .......................................................................................................................................... 21

Labels ....................................................................................................................................... 22

WARRANTY & RETURNS ............................................................................................................. 25

Table of Contents

-2-

Model T26470 (Mfd. Since 1/14)

INTRODUCTION

The Model T26470 is a benchtop Hand Shear

designed to cut light-gauge sheet metal. A station-

ary blade is mounted to the machine base and a

moving blade is connected to the handles. When

the handles are pulled down, the upper blade

moves past the lower stationary blade, creating a

shearing action, similar to a pair of scissors.

The Model T26470 is equipped with a rear adjust-

able work stop for making repetitive cuts of the

same length.

Machine Description

We are proud to provide a high-quality owner’s

manual with your new machine!

made every effort to be exact with the

instruc-

tions, specifications, drawings, and photographs

contained inside. Sometimes we make mistakes,

but

our policy of continuous improvement

also

means that

sometimes the machine

you receive

will be slightly different than what is shown in

the manual

If you find this to be the case, and the difference

between the manual and machine leaves you

confused about a procedure

, check our website

for an updated version. W

e post current

manuals

and

manual updates for free on our website at

www.grizzly.com

Alternatively, you can call our Technical Support

for help. Before calling, please write down the

Manufacture Date

and Serial Number

stamped

into the machine ID label (see below). This infor-

mation helps us determine if updated documenta-

tion is available for your machine.

Manufacture Date

Serial Number

Manual Accuracy

We stand behind our machines. If you have

any questions or need help, use the information

below to contact us. Before contacting, please get

the serial number and manufacture date of your

machine. This will help us help you faster.

Grizzly Technical Support

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Email: [email protected]

We want your feedback on this manual. What did

you like about it? Where could it be improved?

Please take a few minutes to give us feedback.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [email protected]

Contact Info

Model T26470 (Mfd. Since 1/14)

-3-

Figure 1. Hand shear identification (front).

Figure 2. Hand shear identification (rear).

Identification

Handle Grips

Handles

Table

Table Lip

Mounting Feet

Blade Bow

Work Stop

Rods

Work Stop

Assembly

Lower

Blade

-4-

Model T26470 (Mfd. Since 1/14)

The information contained herein is deemed accurate as of 3/19/2014 and represents our most recent product specifications.

Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.

PAGE 1 OF 1Model T26470

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL T26470 HAND SHEAR MACHINE

Product Dimensions:

Weight................................................................................................................................................................ 38 lbs.

Width (side-to-side) x Depth (front-to-back) x Height............................................................... 17-1/2 x 17 x 28-1/2 in.

Footprint (Length x Width)....................................................................................................................... 13 x 4-1/2 in.

Shipping Dimensions:

Type..................................................................................................................................................... Cardboard Box

Content........................................................................................................................................................... Machine

Weight................................................................................................................................................................ 40 lbs.

Length x Width x Height......................................................................................................................... 20 x 16 x 6 in.

Main Specifications:

Capacities

Maximum Width......................................................................................................................................... 12 in.

Maximum Thickness at Half Width Mild Steel..................................................................................... 17 Gauge

Maximum Thickness at Full Width Mild Steel..................................................................................... 20 Gauge

Front Stop Scale Range........................................................................................................................ 7-1/2 in.

Rear Stop Scale Range......................................................................................................................... 9-1/2 in.

Construction

Frame......................................................................................................................................................... Steel

Hold-Down Clamp...................................................................................................................................... Steel

Shear Table................................................................................................................................................ Steel

Shear Blades.............................................................................................................................................. Steel

Shear Blade Type............................................................................................................................... Plain End

Other Specifications:

Country Of Origin ............................................................................................................................................... China

Warranty ........................................................................................................................................................... 1 Year

Approximate Assembly & Setup Time ........................................................................................................ 15 Minutes

Serial Number Location ................................................................................................................... Machine ID Label

Features:

Adjustable rear stop

Easy control rubber grip handles

Mounting base

Model T26470 (Mfd. Since 1/14)

-5-

ELECTRICAL EQUIPMENT INJURY RISKS. You

can be shocked, burned, or killed by touching live

electrical components or improperly grounded

machinery. To reduce this risk, only allow qualified

service personnel to do electrical installation or

repair work, and always disconnect power before

accessing or exposing electrical equipment.

DISCONNECT POWER FIRST.

Always discon-

nect machine from power supply BEFORE making

adjustments, changing tooling, or servicing machine.

This prevents an injury risk from unintended startup

or contact with live electrical components.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating or

observing machinery to reduce the risk of eye

injury or blindness from flying particles. Everyday

eyeglasses are NOT approved safety glasses.

OWNER’S MANUAL. Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained oper-

ators have a higher risk of being hurt or killed.

Only allow trained/supervised people to use this

machine. When machine is not being used, dis-

connect power, remove switch keys, or lock-out

machine to prevent unauthorized use—especially

around children. Make workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use

machinery in areas that are wet, cluttered, or have

poor lighting. Operating machinery in these areas

greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental

alertness is required for safe operation of machin-

ery. Never operate under the influence of drugs or

alcohol, when tired, or when distracted.

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.

This manual uses a series of symbols and signal words intended to convey the level of impor-

tance of the safety messages. The progression of symbols is described below. Remember that

safety messages by themselves do not eliminate danger and are not a substitute for proper

accident prevention measures. Always use common sense and good judgment.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert

against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

This symbol is used to alert the user to useful information about

proper operation of the machine.

NOTICE

Safety Instructions for Machinery

SECTION 1: SAFETY

-6-

Model T26470 (Mfd. Since 1/14)

WEARING PROPER APPAREL. Do not wear

clothing, apparel or jewelry that can become

entangled in moving parts. Always tie back or

cover long hair. Wear non-slip footwear to avoid

accidental slips, which could cause loss of work-

piece control.

HAZARDOUS DUST. Dust created while using

machinery may cause cancer, birth defects, or

long-term respiratory damage. Be aware of dust

hazards associated with each workpiece material,

and always wear a NIOSH-approved respirator to

reduce your risk.

HEARING PROTECTION. Always wear hear-

ing protection when operating or observing loud

machinery. Extended exposure to this noise

without hearing protection can cause permanent

hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on

machinery can become dangerous projectiles

upon startup. Never leave chuck keys, wrenches,

or any other tools on machine. Always verify

removal before starting!

USE CORRECT TOOL FOR THE JOB. Only use

this tool for its intended purpose—do not force

it or an attachment to do a job for which it was

not designed. Never make unapproved modifica-

tions—modifying tool or using it differently than

intended may result in malfunction or mechanical

failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing

and balance at all times when operating machine.

Do not overreach! Avoid awkward hand positions

that make workpiece control difficult or increase

the risk of accidental injury.

CHILDREN & BYSTANDERS. Keep children and

bystanders at a safe distance from the work area.

Stop using machine if they become a distraction.

GUARDS & COVERS. Guards and covers reduce

accidental contact with moving parts or flying

debris. Make sure they are properly installed,

undamaged, and working correctly.

FORCING MACHINERY. Do not force machine.

It will do the job safer and better at the rate for

which it was designed.

NEVER STAND ON MACHINE. Serious injury

may occur if machine is tipped or if the cutting

tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement dur-

ing operation greatly increases risk of injury or

loss of control. Before starting, verify machine is

stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult

this owner’s manual or the manufacturer for rec-

ommended accessories. Using improper acces-

sories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the

risk of accidental injury, turn machine OFF and

ensure all moving parts completely stop before

walking away. Never leave machine running

while unattended.

MAINTAIN WITH CARE. Follow all maintenance

instructions and lubrication schedules to keep

machine in good working condition. A machine

that is improperly maintained could malfunction,

leading to serious personal injury or death.

CHECK DAMAGED PARTS. Regularly inspect

machine for any condition that may affect safe

operation. Immediately repair or replace damaged

or mis-adjusted parts before operating machine.

MAINTAIN POWER CORDS. When disconnect-

ing cord-connected machines from power, grab

and pull the plug—NOT the cord. Pulling the cord

may damage the wires inside. Do not handle

cord/plug with wet hands. Avoid cord damage by

keeping it away from heated surfaces, high traffic

areas, harsh chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time

you experience difficulties performing the intend-

ed operation, stop using the machine! Contact our

Technical Support at (570) 546-9663.

Model T26470 (Mfd. Since 1/14)

-7-

Like all machinery there is potential danger

when operating this machine. Accidents

are frequently caused by lack of familiarity

or failure to pay attention. Use this machine

with respect and caution to decrease the

risk of operator injury. If normal safety pre-

cautions are overlooked or ignored, seri-

ous personal injury may occur.

No list of safety guidelines can be com-

plete. Every shop environment is different.

Always consider safety first, as it applies

to your individual working conditions. Use

this and other machinery with caution and

respect. Failure to do so could result in

serious personal injury, damage to equip-

ment, or poor work results.

Additional Safety for Shear Machines

AMPUTATION HAZARD. The shear blades can

easily pinch, crush, or amputate fingers or other

body parts. Always keep hands, fingers, and other

body parts away from the blades during operation.

RATED CAPACITY. Only use sheet metal that is

within the rated capacity of this shear (refer to the

Machine Data Sheet on Page 4).

SHARP METAL EDGES. Sharp edges on sheet

metal workpieces can easily cause deep cuts

while handling. Wear leather gloves when han-

dling sheet metal, and always chamfer and debur

sharp workpiece edges.

PROPER WORKPIECE MATERIAL. Do not

attempt to cut round stock, glass, wood, dry-

wall, backer board, or plywood. Cutting incorrect

materials can produce unexpected results, which

increases the risk of injury, and may result in dam-

age to the machine.

SECURE SHEAR BEFORE USE. Before using,

fasten shear to a sturdy surface that can with-

stand the dynamic forces involved in cutting sheet

metal. Otherwise, shear may unexpectedly move

or fall, causing serious injury or property damage.

STABLE FOOTING. This shear requires you to

apply moderate force while cutting. Without stable

footing, you could slip or fall, which could cause

personal injury. Always stand with both feet com-

fortably on a non-slip surface during operation.

BODY POSITION. The forces and body motion

required to operate shear can result in operator

injury over time if proper technique is not used.

Always keep your body centered with the machine

and your back straight when applying pressure

against handles.

BLADE CONDITION. Blades that are sharp,

undamaged, and properly adjusted will reduce

risk of injury and improve cutting results. Always

keep blades properly maintained.

BLADE GUARD. The blade guard is designed

to reduce risk of amputation. Always keep guard

properly attached and in good condition during

operation.

-8-

Model T26470 (Mfd. Since 1/14)

SECTION 2: SETUP

Your machine was carefully packaged for safe

transportation. Remove the packaging materials

from around your machine and inspect it. If you

discover any damage, please call us immediately

at (570) 546-9663

for advice.

Save the containers and all packing materials for

possible inspection by the carrier or its agent.

Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi-

tion of your shipment, inventory the contents.

Unpacking

SUFFOCATION HAZARD!

Keep children and pets away

from plastic bags or packing

materials shipped with this

machine. Discard immediately.

The following are needed to complete the setup

process, but are not included with your machine.

Description Qty

• Safety Glasses ........................................... 1

• Cleaner/Degreaser (Page 9) ...... As Needed

• Disposable Shop Rags ............... As Needed

• Hex Wrenches 4, 5, 8mm ........................... 1

Needed for Setup

Inventory

The following is a list of items shipped with your

machine. Before beginning setup, lay these items

out and inventory them.

If any non-proprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

Inventory Qty

A. Machine Base ............................................. 1

B. Handles ...................................................... 2

C. Handle Grips .............................................. 2

D. Table ........................................................... 1

E. Work Stop Rods ......................................... 2

F. Work Stop ................................................... 1

G. Flat Head Cap Screws M6-1 x 16 .............. 2

H. Work Stop Blocks ....................................... 2

NOTICE

If you cannot find an item on this list, care-

fully check around/inside the machine and

packaging materials. Often, these items get

lost in packaging materials while unpack-

ing or they are pre-installed at the factory.

Figure 3. T26470 inventory.

Model T26470 (Mfd. Since 1/14)

-9-

Cleanup Site Considerations

Figure 4. Minimum working clearances.

Workbench Load

Refer to the Machine Data Sheet for the weight

and footprint specifications of your machine.

Some workbenches may require additional rein-

forcement to support the weight of the machine

and workpiece materials.

Consider anticipated workpiece sizes and addi-

tional space needed for auxiliary stands, work

tables, or other machinery when establishing a

location for this machine in the shop. Below is

the minimum amount of space needed for the

machine.

Placement Location

30"

⁄2"

The unpainted surfaces of your machine are

coated with a heavy-duty rust preventative that

prevents corrosion during shipment and storage.

This rust preventative works extremely well, but it

will take a little time to clean.

Be patient and do a thorough job cleaning your

machine. The time you spend doing this now will

give you a better appreciation for the proper care

of your machine's unpainted surfaces.

There are many ways to remove this rust preven-

tative, but the following steps work well in a wide

variety of situations. Always follow the manufac-

turer’s instructions with any cleaning product you

use and make sure you work in a well-ventilated

area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

• Disposable rags

• Cleaner/degreaser (WD•40 works well)

• Safety glasses & disposable gloves

• Plastic paint scraper (optional)

Basic steps for removing rust preventative:

1. Put on safety glasses.

2. Coat the rust preventative with a liberal

amount of cleaner/degreaser, then let it soak

for 5–10 minutes.

3. Wipe off the surfaces. If your cleaner/

degreaser is effective, the rust preventative

will wipe off easily. If you have a plastic paint

scraper, scrape off as much as you can first,

then wipe off the rest with the rag.

4. Repeat Steps 2–3 as necessary until clean,

then coat all unpainted surfaces with a quality

metal protectant to prevent rust.

NOTICE

Avoid chlorine-based solvents, such as

acetone or brake parts cleaner, that may

damage painted surfaces.

-10-

Model T26470 (Mfd. Since 1/14)

Figure 6. Example of a "Direct Mount" setup.

Machine Base

Workbench

Lag Screw

Flat Washer

Another option is a "Direct Mount" (see example

below) where the machine is secured directly to

the workbench with lag screws and washers.

Figure 5. Example of a "Through Mount" setup.

Bench Mounting

Number of Mounting Holes ............................ 4

Diameter of Mounting Hardware .................

⁄8"

The base of this machine has mounting holes

that allow it to be fastened to a workbench or

other mounting surface to prevent it from moving

during operation and causing accidental injury or

damage.

The strongest mounting option is a "Through

Mount" (see example below) where holes are

drilled all the way through the workbench—and

hex bolts, washers, and hex nuts are used to

secure the machine in place.

Machine Base

Workbench

Hex

Bolt

Flat Washer

Lock Washer

Hex Nut

Model T26470 (Mfd. Since 1/14)

-11-

Assembly

This shear is mostly assembled at the factory.

The only assembly required is attaching the table,

work stop, and handle assemblies.

To assemble your machine:

1. Attach handles to levers with the (4) pre-

installed M10-1.5 x 25 cap screws and 10mm

flat washers as shown in Figure 7.

2. Slide handle grips over handles on end with-

out mounting holes as shown in Figure 7.

3. Thread work stop rods through blade bow

and into back of machine (see Figure 8).

Figure 11. Table attached to machine base.

Figure 7. Handles attached.

4. Attach work stop to bottom holes in work

stop blocks with (2) M6-1 x 16 flat head cap

screws (see Figure 9).

5. Slide work stop assembly onto work stop

rods and tighten M8-1.25 x 20 hex bolts (see

Figure 10).

Figure 9. Attaching work stop to stop blocks.

Figure 8. Work stop rods installed.

Work Stop Rods

6. Fasten table to machine base using the (2)

pre-installed M6-1 x 12 cap screws and (2)

6mm flat washers (see Figure 11).

Figure 10. Work stop attached.

Handle Grip

Lever

x 4

Hex Bolts

Work Stop

Bottom Holes

Stop

Block

-12-

Model T26470 (Mfd. Since 1/14)

SECTION 3: OPERATIONS

Shear blades can easily

pinch, crush, or amputate

fingers or other body

parts. Always keep hands,

fingers, and other body

parts away from blades

during operation.

To reduce your risk of

serious injury, read this

entire manual BEFORE

using machine.

If you are not experienced with this type

of machine, WE STRONGLY RECOMMEND

that you seek additional training outside of

this manual. Read books/magazines or get

formal training before beginning any proj-

ects. Regardless of the content in this sec-

tion, Grizzly Industrial will not be held liable

for accidents caused by lack of training.

Damage to your eyes and

hands could result from

using this machine with-

out proper protective gear.

Always wear leather gloves

and safety glasses, when

operating this machine.

Eye injury hazard! Always

wear safety glasses when

using this machine.

Cutting Sheet Metal

To cut sheet metal:

This shear is designed to cut mild steel up to

20-gauge at full width and up to 17-gauge at half

width. Exceeding these capacities can result in

damage to shear blades.

1. Mark cut line across workpiece.

2. Make sure gap between shear blades is cor-

rect for workpiece material (refer to Adjusting

Blade Bow on Page 19 for detailed instruc-

tions).

Model T26470 (Mfd. Since 1/14)

-13-

3. Position workpiece against table lip on right

side of table as shown in Figure 12, then

align cut mark with upper shear blade.

Note: The shearing action begins on the right

side of the workpiece and moves to the left.

Note: If you are using the work stop, adjust

the stop so that at least one square edge of

the workpiece is against it.

4. Clamp workpiece to table to prevent it from

moving while cutting.

5. Keeping all body parts away from blades,

pull down on both handles with an even and

steady pressure to complete cut.

Figure 12. Positioning workpiece for a cut.

Table

Lip

Work Stop

The work stop is used for making repetitive cuts of

the same length. The adjustable assembly allows

the work stop to create workpieces as short as

⁄4" or as long as 8

⁄4".

To position the work stop:

1. Loosen both hex bolts shown in Figure 13.

Figure 13. Hex bolts used for setting work stop.

Hex Bolts

2. Adjust work stop parallel with blades and at

correct distance for cut.

3. Retighten both hex bolts.

Work

Stop

-14-

Model T26470 (Mfd. Since 1/14)

SECTION 4: ACCESSORIES

ACCESSORIES

order online at www.grizzly.com or call 1-800-523-4777

Installing unapproved accessories may

cause machine to malfunction, resulting in

serious personal injury or machine damage.

To reduce this risk, only install accessories

recommended for this machine by Grizzly.

NOTICE

Refer to our website or latest catalog for

additional recommended accessories.

G5618—Deburring Tool with Two Blades

The quickest tool for smoothing freshly sheared

metal edges. Comes with two blades, one for

steel and aluminum, and one for brass and cast

iron.

Figure 14. G5618 Deburring Tool.

T23094—Pneumatic Sheet Metal Shear

This heavy-duty Pneumatic Sheet Metal Shear

provides long life and reliable cutting with an

ergonomic grip for comfort and stability. Shears

most types of plastics and all types of aluminum,

tin, and steel.

Figure 16. T23094 Pneumatic Sheet Metal

Shear.

G5562—SLIPIT

1 Qt. Gel

G5563—SLIPIT

12 Oz. Spray

G2871—Boeshield

T-9 12 Oz. Spray

G2870—Boeshield

T-9 4 Oz. Spray

H3788—G96

Gun Treatment 12 Oz. Spray

H3789—G96

Gun Treatment 4.5 Oz. Spray

Figure 17. Recommended products for protect-

ing unpainted cast iron/steel parts on machinery.

Figure 15. SB1365 Machine Oil-ISO 68.

SB1365—South Bend Way Oil-ISO 68

Engineered for the high pressure exerted on

horizontal or vertical ways and slides. Protects

against rust and corrosion. Ensures stick-free,

smooth motion which maximizes finishes and

extends the life of your machine.

Model T26470 (Mfd. Since 1/14)

-15-

order online at www.grizzly.com or call 1-800-523-4777

H5503—Electric Sheet Metal Shear

This Electric Sheet Metal Shear features a

⁄2 HP,

110V, 2500 RPM, 3.8 amp motor with a 360 de-

gree adjustable swivel head and variable speed

range from 0 to 2500 SPM. Cuts up to 14 gauge

in mild steel and 18 gauge in stainless, at up to

150 inches per minute.

Figure 18. H5503 Electric Sheet Metal Shear.

Super Heavy-Duty Birch Workbench

H8361—60" x 30"

H8362—72" x 36"

Sized to fit the needs of any shop, these Super

Heavy-Duty Birch Workbenches have solid 3"

thick tops that stand 38" above the floor. The end

vise measures 14

⁄4" wide (H8361) or 17

⁄4" wide

(H8362) and has a 7" maximum capacity. Stable

laminated birch provides strength and durability.

You'll be proud to have this workbench in your

shop!

Figure 19. Super heavy-duty birch workbench.

T10727—12" Slip Roll

Use your bench vise as a sturdy base with this

unique Slip Roll. This slip roll has 12" maximum

forming width and 20 gauge maximum mild steel

capacity with 1

⁄16" roll diameter and 1

⁄4" minimum

forming diameter.

Figure 20. T10727 Bench Vise Slip Roll.

-16-

Model T26470 (Mfd. Since 1/14)

T23125—18" Mighty Bender

These light-duty, 18" capacity benders are the

perfect tool to have in every workshop. They

quickly form sheet metal up to 22 gauge and are

amazingly affordable.

Figure 21. T23125 Mighty Bender.

Figure 22. H6136 Air Riveter.

H6136—Air Riveter

If you do a lot of riveting, you can't beat the speed

and convenience of a pneumatic riveter. Simply

connect to an air compressor and squeeze the

trigger for all day riveting. Includes five tips, quick

connect air fitting, and rivet mandrel container.

H7862—Heavy-Duty Hand Punch with Stand

This heavy-duty hand punch easily goes from

stand-mounted operation to hand-held operation

for ultimate flexibility. Comes with 7 different die

sizes including

⁄32",

⁄32" and

⁄32" each having a center tip for easy hole align-

ment.

Figure 23. H7862 Heavy Duty Hand Punch.

order online at www.grizzly.com or call 1-800-523-4777

Model T26470 (Mfd. Since 1/14)

-17-

SECTION 5: MAINTENANCE

Cleaning the Model T26470 is relatively easy. Use

a brush to clear away any metal debris from the

blades and the table.

Use a shop rag to carefully apply a thin coat of

quality metal protectant to all exposed surfaces of

the blades to prevent corrosion (see Page 14 for

offerings from Grizzly).

Cleaning

Alignment Shaft Bushing

Lubrication

For optimum performance from your machine,

follow this maintenance schedule and refer to any

specific instructions given in this section.

Daily:

• Loose mounting bolts.

• Damaged blade guard.

• Damaged or worn blades.

• Any other unsafe condition.

Weekly:

• Lubricate alignment shaft and pivot pin bush-

ings.

Schedule

To reduce risk of shock or

accidental startup, always

disconnect machine from

power before adjustments,

maintenance, or service.

Oil Type ..... Model SB1365 or ISO 68 Equivalent

Oil Amount ..................................... 1 or 2 Squirts

Lubrication Frequency ..............................Weekly

Using an oil can, provide 1–2 squirts of oil into the

oil ports located on the back of the shear machine

(see Figure 24). Raise and lower the handles a

few times to distribute the oil.

Figure 24. Oil port location.

Oil Port

1 of 2

-18-

Model T26470 (Mfd. Since 1/14)

Review the troubleshooting and procedures in this section if a problem develops with your machine. If you

need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663.

Note: Please gather the serial number and manufacture date of your machine before calling.

SECTION 6: SERVICE

Troubleshooting

Symptom Possible Cause Possible Solution

Shear will not cut

workpiece.

1. Workpiece thickness exceeds shear

capacity.

2. Blade bow not correct.

3. Not enough pressure applied.

1. Only use workpiece material within shear capacity

(Page 4).

2. Properly adjust blade bow (Page 19).

3. Safely increase pressure.

Cuts are not square. 1. Work stop not parallel to blades.

2. Blade bow not correct.

1. Properly adjust work stop parallel to blades

(Page 13).

2. Properly adjust blade bow (Page 19).

Poor quality of cuts

(ripping or tearing).

1. Blade bow not correct.

2. Blades worn or damaged.

1. Properly adjust blade bow (Page 19).

2. Sharpen/replace blades (Page 20).

Page is loading ...

Grizzly T26470 Owner's manual

Brand: Grizzly

Model: T26470

Category: Hand tools supplies

Type: Owner's manual

Download PDF

report

Grizzly T26470 Owner's manual

Grizzly T26470 Owner's manual

Related papers

Other documents