Dometic CoolFreeze FC Operating instructions

D4Kompressor-Kühlbox

Bedienungsanleitung

GB 10 Compressor cooler

Operating manual

F 16 Glacière à compression

Notice d’utilisation

E22Nevera por compresor

Instrucciones de uso

I 28 Frigorifero a compressore

Istruzioni per l’uso

NL 34 Compressorkoelbox

Gebruiksaanwijzing

DK 40 Kompressor-køleboks

Betjeningsvejledning

N 46 Kylbox med kompressor

Bruksanvisning

S 52 Kjøleboks med kompressor

Bruksanvisning

FIN 58 Kompressori-kylmälaatikko

Käyttöohje

CoolFreeze

FF, FA, FC, FT

titelseite_neu_a5.fm Seite 1 Dienstag, 22. Februar 2005 4:43 16

Page is loading ...

10 11

GBGB

cable cross section (mm

2

)

12 V-units

24 V-units

extension meters (m)

Battery operation

Your cooling device can be operated with 12 or 24 volt direct voltage. Prior to

connection check wether the voltage indication on the type plate is in accordance

with the battery voltage.

Connect your cooling device as directly as possible to the poles of the battery or to

a plug connection with an at least 15 A fuse.

Pay attention that the plus wire is connected on to the positive pole and the minus

one to the negative pole. In order to avoid loss of voltage and thus decrease of

performance, the cable should be as short as possible and not interrupted. For

this reason avoid additional switches, plugs or feeder boxes.

If the connecting cable is too short or does not belong to the delivery scope of your

model, you have to buy an corresponding cable or an extension by specialized

dealers. Determine the required cable cross section by means of the following

schedule:

Here you find the necessary wire cross section

Note: High-speed battery chargers may only be connected to the battery

after the cooling device and all other consumers have been disconnected

from the battery. Overvoltage could cause damage to the electronics of the

units.

Your cooling device is equipped with a reverse battery protection. It protects your

cooling device against reverse battery by battery connection and against short circuit.

As a protection for your battery, the cooling device switches off automatically if the

voltage is not sufficient.

You will find the cut-out/cut-in voltages in the Technical data.

Mains operation

If possible, always connect your device to the A.C. network with MOBITRONIC

rectifiers.

Safety instructions

• Never touch naked lines with bare hands. This applies above all to operation on

A.C. network: Danger!

• In case of boats: if the devices are mains operated, take care that the power supply

is fitted with a fuse protection over an FI-switch: Danger!

• Installation works in wet rooms should be performed by a specialist!

• Disconnect your cooling device and other consumers from the battery before

connecting a high-speed battery charger!

• Compare the voltage indication on the type plate with the existing power supply.

• Never open the cooling circuit!

• If you connect your cooling device to a battery, never forget that the battery

contains some acid.

• The cooling device is not appropriate for transporting corrosive or solvent-

comprising substances.

• Never cover the ventilations!

• Defrost the cooling device in time.

• Never use hard or sharp tools for removing the ice coat or loosing frozen objects.

• Never use sand-, acid- or solvent-comprising cleaning agents to clean the cooling

tank.

•Your device must be disposed by a specialist.

The safety indications in the text are marked with this symbol:

General

Application and operative range

The cooling device is fitted for refrigerating and deep-freezing food. When you wish

to refrigerate medicines, first check if the refrigerating capacity of the unit meets the

demands of the respective remedies. The device is suitable for ambient temperatures

between -20° and +55° Celsius and an air humidity of max. 90% in continuous

operation. The cooling device can bear a continuous lopside of maximal 30 degrees.

Before the cooling device is exposed to extreme working conditions – such as

expeditions – you should contact the producer. All materials which are used in the

device are generally recognized as safe for food. The cooling circuit is CFC-free.

Installation

After unpacking the device check that no parts are missing (see folding table).

Special accessories are marked with a ”S”.

Place the cooling device in a dry place which is protected against splash water. It

should not be placed directly adjacent to sources of heat such as heating, gas oven,

hot-water pipes or under the blazing sun. The cooling device must be installed in

such a way that the air which is warmed up through the condenser can escape

without problems.

manual 4445100015 28.03.2002 16:04 Uhr Seite 10

12 13

GBGB

Attention, danger! Never manipulate plugs or switches with wet hands or

when your feet are contacted with water! If you operate your cooling device

on board of a boat by means of shore connection to 230-V-network, you

must in any case insert a FI-safety switch. Contact a specialist for advice!

Cleaning

Your cooling device will be delivered cleaned from the factory – you nevertheless

should wipe it out a little bit previous to first use. Take a cloth which has been slightly

moistened with lukewarm water. Pay attention that no water drops into the seals

and possibly damages the electronics. Dry off the cooling device with a cloth after

cleaning. Clean the device periodically and as soon as it is dirty.

Attention: Never use solvent agents or agents with sand or acid parts for

cleaning the cooling tank!

Never use brushes, graters or hard and sharp tools.

Initial operation

Switch on the cooling device by rotating the switch button clockwise (see ”B” on the

folding table). By rotating the button forward, you can regulate the temperature.

Units with energy accumulator additionally have a knob to activate the storage (see

position ”C” on the folding table). With the energy accumulator refrigerating energy

can be stored up to 8 hours. The activation of the stored energy will be done auto-

matically when the cut-out voltage is reached (see technical data) or when the knob

”C” is pushed mechanically. The energy accumulator will be automatically loaded

again as soon as the cut-in voltage is exceeded or the energy accumulator is

unloaded and it will be mechanically loaded again when the thermostatknob (”B”)

is rotated by means of which the knob to activate the storage is unlocked.

Putting out of service

If you want to cut out the cooling device for a longer period, draw off the plug of the

A.C. line or disconnect the cooling device cable from the battery. Clean the cooling

device and leave the lid or the door slightly open. Thus prevent the formation of

smells.

Defrosting

Air humidity can deposit on the evaporator or in the interior of the cooling device

as frost so that the refrigerating performance is reduced. In order to remove the ice

coat never use hard or sharp tools which can cause damage to the plastics or the

evaporator.

Therefore defrost the cooling device in good time. Take out the refrigerated products

and store them in another cooling device so that they remain refrigerated. Set the

switch button on ”0” and leave the lid or the door open. Wipe the condension water

or – if existing – empty the drip basin.

Tips for energy saving

• The mounting place should be cool, well ventilated and protected against

sunbeams.

• First let warm food get cold, before you store it.

• Defrost your cooling device as soon as an ice coat has been formed.

•Avoid a too cold internal temperature!

• Do not open the cooling device more often than necessary!

• Do not leave the lid or the door open any longer than necessary!

Specific information

Fixing possibilities

We recommend special fixing kits tailored to each cool box version for fixing the box

optimally.

If required, please order separately!

Cool box Fixing kit

FF-20 Art.-No.: W2087.ST

FF-30 Art.-No.: W1440.ST

FA-30 Art.-No.: W1440.ST

FF-40 Art.-No.: W1440.ST

FA-40 Art.-No.: W1440.ST

FC-30 Art.-No.: W1440.ST

FC-40 Art.-No.: W1440.ST

FT-30 Art.-No.: W1627.ST

Vehicle specific fixing kits on demand.

Battery controller ”D”

The cool box is equipped with a battery controller cutting out and cutting in the

compressor and thus protecting battery and compressor.

The following schedule indicates the cut-out and cut-in voltages, measured at the

connecting terminals of the battery controller!

Cut-out voltage Cut-in voltage

12 V/24 V 12 V/24 V

low 10,4 V low 22,8 V low 11,7 V low 24,2 V

high 11,3 V high 24,6 V high 12,5 V high 26,0 V

manual 4445100015 28.03.2002 16:04 Uhr Seite 12

14 15

GBGB

585 340

346 271

408

320

FC-30

480

341

405

401

326

345

FT-30

585 340

271

346

400

484

FC-40

FF-90

* Re = Refrigeration / Df = deep-freeze

ti = interior temperature / ta = ambient temperature

550

300

260

200

425

345

FF-20

585 340

271

346

400

484

FF-40/FA-40

585 340

346 271

408

320

FF-30/FA-30

390

465

494

594

786

173

500

450

355

FF-70

Specifications

Exterior made in grey coated sheet steel; bottom and cover

grained grey polystyrol. Recessed handle grips and cup

holders. Insulated with 30 mm solid polyurethan foam;

FF-70/FF-90: insulated with 50 mm solid polyurethan foam.

Desig- Capacity Cooling Temperature Weight Average Battery Running time per hour Finish System Standard Accessories:

nation range power con- load at ti* = +5°C and equipment Plastic coated

sumption per h ta* = 20°C (32° C)* basket

FF-20 20 ltr. 18 kg 45 W 18% (28%) W2086.3

FF-30 30 ltr. 18 kg 45 W 20% (30%) W529.3

FA-30 20 ltr. 19 kg 45 W 15% (25%) –

FF-40 37.5 ltr. 20 kg 45 W 23% (33%) W2995.3

FA-40 37.5 ltr. 21 kg 45 W 18% (28%) –

FF-70 70 ltr. 25 kg 65 W 30% (40%) –

FF-90 90 ltr. 28 kg 65 W 35% (45%) –

FC-30 30 ltr. 18 kg 45 W 20% (30%) W529.3

FC-40 37.5 ltr. 20 kg 45 W 23% (33%) W2995.3

FT-30 30 ltr. 18 kg 45 W 20% (30%) W529.3

direct

evaporator

Re/Df

+5°C to -15° C

direct

evaporator

Re/Df

+5°C to -15° C

direct

evaporator

Re/Df

+5°C to -15° C

direct

evaporator

Re/Df

+5°C to -15° C

direct

evaporator

Re/Df

+5°C to -15° C

direct

evaporator

Re/Df

+5°C to -15° C

direct

evaporator

Re/Df

+5°C to -15° C

direct

evaporator

Re/Df

+5°C to -15° C

energy

accumulator

Re

+10°C to 0° C

energy

accumulator

Re

+10°C to 0° C

average power consumption × percentage running time

Fully hermetic DANFOSS BDF-compressor with electronic

control equipment and integrated undervoltage protection

for 12/24 Volt DC. Alu-rollbond evaporator (FF) or aluminium

energy accumulator. Variable automatic thermostat with

activation of energy accumulator (FA).

FF-70/FF-90: AC/DC converter (100-240V)

FF-20, FF/FA-30, FF/FA-40, FC-30, FC-40 and FT-30:

DC connection cable and user’s manual

FF-70 and FF-90:

DC and AC connection cable,

wire basket, mountable handles, user’s manual.

manual 4445100015 28.03.2002 16:04 Uhr Seite 14

Page is loading ...

Europe

Dometic Austria GmbH

Neudorferstrasse 108

2353 Guntramsdorf

℡ +43 2236 908070

 +43 2236 90807060

Mail: [email protected]

Dometic Switzerland AG

Riedackerstrasse 7a

CH-8153 Rümlang (Zürich)

℡ +41 44 8187171

 +41 44 8187191

Mail: [email protected]

Dometic Denmark A/S

Nordensvej 15, Taulov

DK-7000 Fredericia

℡ +45 75585966

 +45 75586307

Mail: [email protected]

Dometic Spain S.L.

Avda. Sierra del Guadarrama, 16

E-28691 Villanueva de la Cañada

Madrid

℡ +34 902 111 042

 +34 900 100 245

Mail: [email protected]

Dometic S.N.C.

ZA du Pré de la Dame Jeanne

F-60128 Plailly

℡ +33 3 44633500

 +33 3 44633518

Mail: [email protected]

Dometic Finland OY

Mestarintie 4

FIN-01730 Vantaa

℡ +358 20 7413220

 +358 9 7593700

Mail: [email protected]

Dometic Italy S.p.A.

Via Virgilio, 3

I-47100 Forlì

℡ +39 0543 754901

 +39 0543 756631

Mail: [email protected]

Dometic Norway AS

Skolmar 24

N-3232 Sandefjord

℡ +47 33428450

 +47 33428459

Mail: firmapost@waeco.no

Dometic Benelux B.V.

Ecustraat 3

NL-4879 NP Etten-Leur

℡ +31 76 5029000

 +31 76 5029090

Mail: [email protected]l

Dometic Scandinavia AB

Gustaf Melins gata 7

S-42131 Västra Frölunda

(Göteborg)

℡ +46 31 7341100

 +46 31 7341101

Mail: [email protected]

Dometic UK Ltd.

Dometic House · The Brewery

Blandford St. Mary

Dorset DT11 9LS

℡ +44 844 626 0133

 +44 844 626 0143

Mail: [email protected]

A

CH

DK

E

F

FIN

I

N

NL

S

UK

Overseas + Middle East

Dometic Australia

1 John Duncan Court

Varsity Lakes QLD 4227

℡ +61 7 55076000

 +61 7 55076001

Mail: [email protected]

WAECO Impex Ltd.

Suites 2207-2211 · 22/F · Tower 1

The Gateway · 25 Canton Road

Tsim Sha Tsui · Kowloon

Hong Kong

℡ +852 24611386

 +852 24665553

Mail: info@dometic-waeco.com.hk

WAECO Impex Ltd.

Taipei Office

2 FL-3 · No. 56 Tunhua South Rd, Sec 2

Taipei 106, Taiwan

℡ +886 2 27014090

 +886 2 27060119

Mail: marketing@waeco.com.tw

Dometic AB

Regional Office Middle East

P O Box 74775

Dubai, United Arab Emirates

℡ +971 4 321 2160

 +971 4 321 2170

Mail: [email protected]

Dometic Marine Division

2000 N. Andrews Ave. Extension

Pompano Beach, FL 33069 USA

℡ +1 954 973 2477

 +1 954 979 4414

Mail: marinesales@dometicusa.com

AUS

HK

ROC

UAE

USA

Dometic WAECO International GmbH

Hollefeldstraße 63 · D-48282 Emsdetten

℡ +49 (0) 2572 879-195 ·  +49 (0) 2572 879-322

Mail: info@dometic-waeco.de · Internet: www.dometic-waeco.de

D

www.dometic-waeco.com

4445100015 10/2010

adresse_A5_31.fm Seite 2 Donnerstag, 9. September 2010 11:10 11

Dometic CoolFreeze FC Operating instructions

This manual is also suitable for

Dometic CoolFreeze FC Operating instructions

in other languages

Related papers

Other documents