Omnitron Systems Technology iConverter 10GXT Owner's manual

Brand
Omnitron Systems Technology
Model
iConverter 10GXT
Category
Network media converters
Type
Owner's manual

Omnitron Systems Technology iConverter 10GXT is a 10/100/1000BASE-T copper to 1000BASE-X or 10GBASE-R fiber media converter that supports jumbo frames up to 10,056 bytes and is available as a compact, unmanaged standalone unit. The 10GXT models are available with SFP+ or XFP transceivers. It features LED indicators for power, port negotiation mode, link activity, and duplex mode. The DIP-switch configuration options allow for customization of port speed, duplex, and link modes. The device can be powered using either an AC/DC adapter or a DC power source.

Omnitron Systems Technology iConverter 10GXT is a 10/100/1000BASE-T copper to 1000BASE-X or 10GBASE-R fiber media converter that supports jumbo frames up to 10,056 bytes and is available as a compact, unmanaged standalone unit. The 10GXT models are available with SFP+ or XFP transceivers. It features LED indicators for power, port negotiation mode, link activity, and duplex mode. The DIP-switch configuration options allow for customization of port speed, duplex, and link modes. The device can be powered using either an AC/DC adapter or a DC power source.

iConverter
®
10GXT
Standalone Module User Manual
Product Overview
The iConverter 10GXT is a 10/100/1000BASE-T copper to 1000BASE-X or 10GBASE-R ber
media converter, and is available as a compact, unmanaged standalone unit. The iConverter
10GXT supports jumbo frames up to 10,056 bytes. The 10GXT models are available with
SFP+ or XFP transceivers.
Installation Procedure
1) Congure DIP-switches
2) Install Standalone Module and Connect Cables
3) Verify Operation
1) CONFIGURE DIP-SWITCHES
DIP-SWITCH BANK 1
The location of the DIP-switches is shown in Figure 1.
The function of DIP-switch Bank is outlined in Figure 2.
Switch Legend Function DOWN (Default) UP
SW1
P1 AN/MAN Port 1 Speed and Duplex Auto Manual
SW2
SW3 10G/1000 Port 2 Speed 10G 1000
SW4 P2 AN/MAN
Port 2 Negotiation
(1G Mode Only)
Auto Manual
SW5
Link Modes
Asymmetrical Link Propagate
Port 1 to Port 2
Link Segment
Link Propagate
Port 1 to Port 2
SW6
Asymmetrical Link Propagate
Port 2 to Port 1
Link Segment
Link Propagate
Port 2 to Port 1
Figure 2: DIP-switch Denitions
3) VERIFY OPERATION
Once the module has been installed and congured per steps 1 and 2, verify the module is
operational by viewing the LED indicators.
LED Function
“Legend”
Color OFF State ON/Blinking State
Power
“PWR”
Green No power Solid Green: Module has power
P1 Negotiation Mode
“AN”
Green
Port is congured for Manual
operation
Solid Green: Port is congured for auto-
negotiation
Blinking Green: Port is congured for
auto-negotiation but has not completed
the process with attached link partner
P1 Link Activity
“100”
Green Port not linked at 100M
Solid Green: Port linked at 100M
Blinking Green: Data activity
P1 Link Activity
“1000”
Green Port not linked at 1000M
Solid Green: Port linked at 1000M
Blinking Green: Data activity
P1 Link Activity
“100” and “1000”
Green Port not linked at 10M
Solid Green: Port linked at 10M
Blinking Green: Data activity
P1 Duplex
“FDX”
Green
Port is congured for half
duplex per DIP-switch or
resolved by auto-negotiation
Solid Green: Port is congured for
full duplex operation per DIP-switch or
resolved by auto-negotiation
P2 Speed
“P2 1000”
(SFP+ Model Only)
Green/
Amber
Port not linked at 1000M
Solid Green: Port linked at 1000M
Blinking Green: Data activity
Blinking Amber: Port is operating at
1000M and receiving a remote fault
P2 Speed
“10G”
Green Port not linked at 10G
Solid Green: Port linked at 10G
Blinking Green: Data activity
P2 FDX Green
Port is has negotiated to
half duplex or port has not
established a link
Solid Green: Port is negotiated to full
duplex operation by auto-negotiation
P2 DDMI
“Stats”
Green/
Amber
Transceiver does not support
digital diagnostic or no
transceiver is installed
Green Solid: Transceiver supports
digital diagnostic and no DDMI alarm
detected
Amber Solid: Transceiver supports
digital diagnostic and DDMI alarm
detected
Figure 5: LED Indicators
LED Legend/State
Link Speed
“1000” “100”
OFF OFF Port not linked
OFF ON Port linked at 100Mbps
ON OFF Port linked at 1000Mbps
ON ON Port linked at 10Mbps
Figure 6: Port 1 Speed LED Indicators
040-08580-001A 1/16
Page 1
Omnitron Systems Technology * 38 Tesla, * Irvine, CA 92618
949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com
©2016 Omnitron Systems Technology, Inc. iConverter is a registered trademark of Omnitron Systems Technology, Inc.
Trademarks are owned by their respective companies. Specications subject to change without notice. All rights reserved.
SW1 and SW2: Port 1 Speed and Duplex
Negotiation mode, duplex mode and speed per Figure 3.
SW1 SW2 RJ-45 Mode of Operation
DOWN DOWN
Set to auto-negotiation with the following modes are advertised:
1000FDX, 1000HDX, 100FDX, 100HDX, 10FDX, 10HDX
DOWN UP The RJ-45 port is set to manual and is forced to 10FDX
UP DOWN The RJ-45 port is set to manual and is forced to 100HDX
UP UP The RJ-45 port is set to manual and is forced to 100FDX
Figure 3: Port Speed and Duplex Selection
SW3: Port 2 Speed (SFP+ Model Only)
This DIP-switch congures the speed of the transceiver installed in Port 2. If the DIP-switch is
in the Down “10G” (default) position, the port forces the speed of the transceiver to 10G. If the
DIP-switch is in the Up “1000” position, the port forces the speed of the transceiver to 1000.
SW4: Port 2 Negotiation Mode “AN/MAN” (SFP+ Model Only)
SW4 is used when SW3 is in the Up “1000” position.
When this DIP-switch is in the Down “AN” position (factory default), the ber optic port
automatically determines the duplex and pause modes of the connecting ber optic device.
If the connecting ber optic device cannot provide the proper signal to indicate its own mode
of operation, the DIP-switch should be set to the Up “MAN” position. When Port 2 is set to
manual mode, no capabilities are advertised.
SW5 and SW6: Link Modes
These DIP-switches congure the link mode settings. It is recommended to have link modes
Down position (default) during the initial installation. After the circuit has been tested and
operational, congure the module for the desired mode.
Link Segment
In Link Segment mode, all ports operate independently. A loss of a receive link signal will
only affect the port detecting the loss of signal. All the other ports will continue to generate
a link signal.
Asymmetrical Link Propagate
In Asymmetrical Link Propagate mode, faults are propagated based on the port notation. Port 1
to Port 2 notation indicates the direction the loss of link signal will propagate. A loss of receive
link on the ber optic Port 1 causes the UTP Port 2 to drop its link due to the propagated
state (Port 1 to Port 2). The loss of link on the UTP Port 2 does not cause the loss of link to
propagate. The loss only propagates in the Port 1 to Port 2 direction.
Symmetrical Link Propagate
In Symmetrical Link Propagate mode, the loss of a receive link signal will continue to propagate
through to the next port in the network causing the port to drop link.
SW5 SW6 Function
DOWN DOWN Link Segment (default)
UP DOWN Asymmetrical Link Propagate P1 to P2
DOWN UP Asymmetrical Link Propagate P2 to P1
UP UP Symmetrical Link Propagate
Figure 4: DIP-switch BANK 1 Denitions
Page 2 Page 3
For detailed information on the operation of the different Link Modes, download the application
note “iConverter Link Modes” available on Omnitron’s website:
https://www.omnitron-systems.com/cat_view/20-omnitron-download-center/21-iconverter-
product-documentation/114-application-notes-and-other-documents.php
2) INSTALL STANDALONE MODULE AND CONNECT CABLES
a. The 10GXT is available as a standalone module with or without integrated mounting
brackets. For wall-mounting, use the integrated mounting brackets to attach the 10GXT
to a wall, backboard or other at surface. For tabletop installations, place the unit on a
at level surface. Attach the rubber feet to the bottom of the 10GXT to prevent the unit
from sliding. Make sure the unit is placed in a safe, dry and secure location. Wall-mount
brackets (8249-0) are available to mount the standalone module without integrated
mounting brackets.
To power the unit using the AC/DC adapter, connect the AC/DC adapter to an AC outlet.
Then connect the barrel plug at the end of the wire on the AC/DC adapter to the 2.5mm
DC barrel connector (center-positive) on the unit. Conrm that the unit has powered up
properly by checking the power status LED located on the front of the unit.
To power the unit using a DC power source, prepare a power cable using a two conductor
insulated wire (not supplied) with a 14 AWG gauge minimum. Cut the power cable to the
length required. Strip approximately 3/8 of an inch of insulation from the power cable
wires. Connect the power cables to the unit by fastening the stripped ends to the DC
power connector.
Connect the power wires to the DC power source. The Power LED should indicate the
presence of power.
WARNING: Note the wire colors used in making the positive and negative connections.
Use the same color assignment for the connection at the DC power source.
A ‘P’ clamp is included to provide strain relief for the AC/DC cable. Attach the ‘P’ clamp
to the safety ground screw located at the rear of the module.
NOTE: When using the ‘P’ clamp, attach the ‘P’ clamp to the safety ground screw.
Make sure the ‘P’ clamp in installed between the washer and the screw.
NOTE: A safety ground attachment is provided on the rear of the chassis. Use
the provided ground screw to attach a safety ground.
AC Power
Requirements
AC Adapter:
(US)
100 - 120VAC/60Hz
0.25A @ 120VAC (max)
AC Adapter:
(Universal)
100 - 240VAC/50 - 60Hz
0.25A @ 120VAC (max)
DC Power
Requirements
DC Input:
(Terminal Block)
9 - 16VDC, 2.8A max
2-Pin Terminal (non-isolated)
DC Input:
(AC Adapter)
9 - 16VDC, 2.8A max
2.5mm Barrel Connector
b. Insert the appropriate 10G SFP+, 1G SFP or XFP transceiver (depending on the model
of the module) into Port 2 receptacle on the 10GXT. The release latch of the transceiver
must be in the closed position before insertion.
c. Connect an appropriate multimode or single-mode ber cable to the ber transceiver port
on the 10GXT. It is important to ensure that the transmit (Tx) is attached to the receive
side of the device at the other end and the receive (Rx) is attached to the transmit side.
d. Connect the RJ-45 port via a CAT 6A or better cable to a 10BASE-T, 100BASE-TX or
1000BASE-T Ethernet device.
  • Page 1 1
  • Page 2 2

Omnitron Systems Technology iConverter 10GXT Owner's manual

Brand
Omnitron Systems Technology
Model
iConverter 10GXT
Category
Network media converters
Type
Owner's manual

Omnitron Systems Technology iConverter 10GXT is a 10/100/1000BASE-T copper to 1000BASE-X or 10GBASE-R fiber media converter that supports jumbo frames up to 10,056 bytes and is available as a compact, unmanaged standalone unit. The 10GXT models are available with SFP+ or XFP transceivers. It features LED indicators for power, port negotiation mode, link activity, and duplex mode. The DIP-switch configuration options allow for customization of port speed, duplex, and link modes. The device can be powered using either an AC/DC adapter or a DC power source.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents