Hunter Fan Company 59157 User manual

Brand: Hunter Fan Company

Model: 59157

Category: Household fans

Type: User manual

www.HunterFan.com

1.888.830.1326

Table of Contents

Congratulations on purchasing

your new Hunter® ceiling fan! It will

provide comfort and performance

in your home or ofce for many

years. This installation and operation

manual contains complete

instructions for installing and

operating your fan.

We are proud of our work and

appreciate the opportunity to

supply you with the best ceiling fan

available anywhere in the world.

To register your fan, please visit:

www.HunterFan.com/register

Save your receipt for proof of purchase.

PAGE

30 inches

7 feet

PAGE

What to Expect with

Your Installation

Ceiling Bracket

Ladder

PAGE

Tools Needed

Troubleshooting

PAGE

Mounting Options

PAGE

Wiring CanopyDownrod

PAGE

Blades

PAGE

Remote Control

PAGE

Operation,

Maintenance & Cleaning

PAGE

Light Kit

PAGE

Switch Housing

www.HunterFan.com

1.888.830.1326

Know your wiring

If you are unfamiliar

with wiring, use a

qualied electrician.

You may need a

friend to help you.

Check box to see

fan weight

Assess location

30 inches

from blade tip

to nearest wall

or obstruction

7 feet

from bottom

edge of blade

to the oor

Select a downrod length

Assess ceiling angle

Must be able to

secure the fan to

building structure or

fan-rated outlet box

Standard Downrod

for ceilings 8-10 feet high

Shorter Downrod

for fans installed close to ceiling

Longer Downrod

for ceilings 10 feet or higher

Ceiling angles greater

than 34° will require an

Angled Mounting Kit.

See page 4 for details.

w.1 - To reduce the risk of re, electrical shock, or personal injury,

mount fan directly from building structure and/or an outlet box marked

acceptable for fan support of 70 lbs (31.8 kg) and use the mounting

screws provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or servicing your

fan, disconnect the power by turning off the circuit breakers to the outlet

box and associated wall switch location. If you cannot lock the circuit

breakers in the off position, securely fasten a prominent warning device,

such as a tag, to the service panel.

w.3 - To reduce the risk of re, electrical shock, or motor damage, use only

Hunter Solid State Speed Controls.

w.4 - To reduce the risk of personal injury, do not bend the blade brackets when

installing the blade brackets, balancing the blades, or cleaning the fan. Do not

insert foreign objects in between rotating fan blades.

c.1 - All wiring must be in accordance with national and local electrical codes

ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied electrician.

c.2 - Use only Hunter replacement parts.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate

radio frequency energy and if not installed and used in accordance with the

instructions may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: modications not approved by the party responsible for compliance

could void user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Read and Save These Instructions

This product conforms to UL Standard 507.

WARNINGS

CAUTIONS

What to Expect with Your Installation

www.HunterFan.com

1.888.830.1326

Tools Needed

Ladder

Power Drill

(optional)

9/64” Drill Bit

(optional)

Screwdrivers

Pliers Wire Strippers

If mounting to a support structure, you will also need these tools.

www.HunterFan.com

1.888.830.1326

If you have an angled ceiling:

1. You will need a longer downrod (sold separately).

2. If your ceiling angle is greater than 34°, you will

also need an Angled Mounting Kit (sold separately).

Guide Touches

BOTH Ceiling & Wall

Guide Touches

Wall

but

NOT Ceiling

You need BOTH

a Longer

Downrod &

an Angled

Mounting Kit

You need ONLY

a Longer

Downrod

*most common

If you have a at ceiling:

Hang your fan by a standard downrod (included).

Mounting Options

Use Standard Mounting

or Low-Prole Mounting

to hang the fan from a at ceiling.

Use Angled Mounting

to hang the fan from a

vaulted or angled ceiling.

CEILING

WALL

OPTION

Standard

Mounting

OPTION

Angled

Mounting

2 3

SLIDE

toward ceiling

PLACE

against wall

FOLD

on dotted line

34°

Use the three steps below to determine if your ceiling angle is greater than 34°

Support

Structure

Ceiling

Outlet Box

(required)

Angled

Mounting

Style

Standard

Mounting

Style

Support

Structure

Ceiling

Outlet Box

(required)

1.888.830.1326

www.HunterFan.com

1.888.830.1326

Ceiling Bracket

Refer to warning w.1 on pg. 2

To avoid possible electrical shock, before

installing your fan, disconnect the power by

turning off the circuit breakers to the outlet

box associated with the wall switch location.

For angled ceilings, point

opening toward peak.

If you are unable to do this,

call Technical Support at

1-888-830-1326.

Make sure all four bumpers are

still attached.

Use wood screws

(included) when securing

to support structure with

approved electrical outlet

box. Drill 9/64” pilot holes

in support structure to aid

in securing ceiling bracket

with hardware found in

the hardware bag.

Use machine screws

(provided with outlet

box) when securing to

existing ceiling fan-rated

outlet box. Make sure

it is securely installed

and is acceptable for fan

support of 31.8 kg (70 lbs)

or less.

OFF

Turn Power

www.HunterFan.com

1.888.830.1326

Downrod

Slide

1 2 3 4 5

678910

Sold Separately

Included

Longer

Downrod

for angled

ceilings or

ceilings 10’ or

higher

Shorter

Downrod

for fans installed

close to ceiling

Standard

Downrod

for ceilings 8-10’ high

Option 1Option 2

Option 3

skip to next page

If you need a different downrod length follow these steps:

Steps 1-5 to remove standard downrod pipe

Steps 6-10 to reassemble with new pipe

Included

(pre-assembled)

www.HunterFan.com

1.888.830.1326

Downrod (continued)

Hand tighten the downrod (at

least 4-5 full turns) until it stops.

KEEP!

Remove the pre-installed setscrew so that

the downrod can be inserted.

1.888.830.1326

www.HunterFan.com

Slide the adapter cover onto the downrod

until it rests against the hanger ball.

Adapter

Cover

Hanger

Ball

Note: e adapter cover is not

used for low-proﬁle mounting.

www.HunterFan.com

1.888.830.1326

8”

3/8”

(not to scale)

The wires can be cut, but leave at least 8”

extending from the top of the downrod.

Downrod (continued)

8”

3/8”

Tighten the setscrew with pliers.

DO NOT HAND TIGHTEN.

If the setscrew is not tightened

securely, the fan may fall.

Lower the adapter cover until it rests

ush against the motor housing.

www.HunterFan.com

1.888.830.1326

Downrod (continued)

DO NOT PICK THE FAN UP BY THE

CANOPY OR WIRES. Place the downrod

ball into the slot in the ceiling bracket.

Put the wires and downrod through the

canopy. Let the canopy sit loosely on top

of the fan.

www.HunterFan.com

1.888.830.1326

Wiring

Turn the splices upward and push them carefully back through the hanger bracket

into the outlet box. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the outlet box.

Refer to CAUTION c.1 on pg. 2

green/yellow

stripe (grounding)

green/yellow

stripe

green/yellow stripe

Note: To connect the wires, hold

the bare metal leads together and

place a wire connector over them,

then twist clockwise until tight.

Using an orange wire connector

from the hardware bag:

Connect the 3 grounding wires

(green, green/yellow stripe, or bare

copper) coming from the ceiling,

downrod, and ceiling bracket.

Receiver

Place the receiver on top of the downrod

assembly as shown.

Tip: If you have difculty tting the receiver

into place, make sure you have cut the excess

wires from the fan. See the Downrod section

for more details.

www.HunterFan.com

1.888.830.1326

Wiring (continued)

Turn the splices upward and push them carefully back through the hanger bracket

into the outlet box. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the outlet box.

Refer to CAUTION c.1 on pg. 2

Note: If you have a dual switch,

please cap the secondary power

wire from the ceiling. This will

result in one unused switch.

Using the orange wire connectors

from the hardware bag:

• Connect the black (ungrounded)

wire from the ceiling to the black

wire from the receiver.

• Connect the white (grounded)

wire from the ceiling to both the

white wire from the receiver and

the white wire from the fan.

black

blue

yellow

blue

Using the orange wire connectors

from the remote control hardware bag:

• Connect the yellow wire from

the receiver to the black wire

from the fan.

• Connect the blue wire from the

receiver to the blue wire (or

possibly black with white stripe

wire) from the fan.

black

(ungrounded)

white (grounded)

black

white

www.HunterFan.com

1.888.830.1326

Canopy

Lift the canopy into place so that

the screw holes are aligned.

Position the canopy so that, when

lifted into place, the canopy ts into

the hanging bracket as shown.

Insert the two canopy screws

found in the hardware bag.

Note: Fan style may vary.

Screw

Holes

www.HunterFan.com

1.888.830.1326

Blades

Secure each blade to a blade iron as shown using

the blade nuts, found in the hardware bag,

and the blade assembly screws, found in the

hardware bag.

www.HunterFan.com

1.888.830.1326

Make sure the upper switch housing is securely

attached to the mounting plate. Failure to properly

secure all 3 assembly screws could result in the switch

housing xture falling.

Switch Housing

Feed the 9-pin plug connector coming from

the bottom of the motor housing through

the center hole in the light kit assembly.

Connect it to the plug connector found

in the switch housing area of the light kit

assembly. Make sure to line up the colored

markings on the connectors.

Partially install two light kit assembly

screws, found in the hardware bag,

halfway into the motor housing as

shown. It does not matter which two

screw holes you choose.

Align the keyhole slots in the top of

the light kit assembly with the partially

installed assembly screws. Wrap the

keyhole slots around the screws and

twist counterclockwise.

www.HunterFan.com

1.888.830.1326

Light Kit

Make sure the light kit assembly is securely attached to the

motor housing. Failure to properly secure all three assembly

screws could result in the light xture falling.

Insert a third light kit assembly screw,

found in the hardware bag, into place

and tighten all three screws securely.

Carefully push all switch housing

components into the switch housing,

then install the switch housing plate

using two light kit assembly screws,

found in the hardware bag.

www.HunterFan.com

1.888.830.1326

Light Kit (continued)

CONGRATULATIONS!

YOU’RE DONE!

See next page for fan

operation instructions.

Position the notches in the outer rim of

the globe so they line up with the tabs on

the inside surface of the light xture rim.

Carefully lift the globe up inside the light

xture as far as it will go. Rotate the globe

in a clockwise direction until it is held

tightly in place by the three tabs.

Install a light bulb in each socket.

When necessary, replace with bulbs of

the same wattage.

Bulb

Notch

Tab

www.HunterFan.com

1.888.830.1326

Remote Control

To access the battery compartment,

remove the small Phillips head screw that

secures the battery door to the transmitter

assembly. The battery should be installed

with the positive (+) side up. Replace with a

CR2032 battery when necessary.

Phillips

Head

Screw

Battery

Door

Turn Power

The remote transmitter should already be paired

to the receiver and ready to use.

Note: If your need to pair your remote, turn fan

power off and back on at the wall switch. Within 3

minutes, press and hold both the Fan Off button

and the High button for 4 seconds to pair the

remote. To prevent faulty operation, please

ensure all other ceiling fans within range are

turned off at the wall switch while pairing.

www.HunterFan.com

1.888.830.1326

Rocker- Style Plate

Switch Cover Plate

Removed Tabs

To install the transmitter cradle, remove the

two screws holding the switch cover plate. Do

not remove the cover plate. Orient the cradle

by lining up the two mounting holes with

those on the cover plate. Insert and tighten

the screws. Do not over tighten.

Note: For rocker-style cover plates, break off

the tabs by pushing outward.

To turn on fan, press a fan speed button. Speeds

range from off (0) to high (3). Quickly press the

Light button to turn the lights off and on.

Medium

Speed

Light

High

Speed

Fan

Off

Low

Speed

Operation, Maintenance, & Cleaning

To switch the direction of air ow, move the

reverse switch to the opposite position. You

will need to remove the glass to do so.

Reverse

Switch

www.HunterFan.com

1.888.830.1326

Operation, Maintenance, & Cleaning (continued)

For cleaning the fan, use soft brushes or

cloths to prevent scratching. Cleaning

products may damage the nishes.

Safe-Exit

• Press the Fan Off button for at least three seconds to

initiate the Safe-Exit Mode.

• The lights will ash for visual conrmation.

• The lights will stay on 50% brightness for 15 seconds and

then begin to dim. After a total of 30 seconds, the lights

will be completely off.

The Safe-Exit Program gives you about thirty seconds

of light when you turn the lights off to exit the room

before the lights go out. To use Safe-Exit:

Note: For CFL lighting, the lights will stay on 100%

brightness for 30 seconds. After a total of 30 seconds, the

lights will be completely off.

www.HunterFan.com

1.888.830.1326

Troubleshooting

Excessive wobbling

• Tighten all of the blade and

blade iron screws until they

are snug.

• Turn the power off, support

the fan carefully, and check

that the hanger ball is

properly seated.

• Use the provided balancing

kit and instructions to balance

the fan.

Noisy Operation

• Tighten the blade and blade

iron screws until they are snug.

• Check to see if any of the

blades are cracked. If so, replace

all of the blades.

Fan doesn’t work

• Make sure power switch is on.

• Pull the pull chain to make sure

it is on.

• Push the motor reversing switch

rmly left or right to ensure that

it is engaged.

• Check the circuit breaker to

ensure the power is turned on.

• Make sure the blades spin freely.

• Turn off power from the circuit

breaker, then loosen the canopy

and check all the connections

according to the wiring diagram

on pages 10-11.

• Check the plug connection in

the switch housing.

Remote control of fan is erratic

• Make sure the battery is

installed correctly.

• Install a fresh battery.

If you have multiple remotes or

multiple remote-controlled fans

installed on the same circuit

breaker and you are experiencing

interference or faulty operation of

your remote controls, please go to

www.HunterFan.com/FAQs

and click “How do I properly install

multiple remote-controlled fans?”

for information on how to correct

this issue.

Hunter Fan Company 59157 User manual

Brand: Hunter Fan Company

Model: 59157

Category: Household fans

Type: User manual

Download PDF

report

Hunter Fan Company 59157 User manual

Hunter Fan Company 59157 User manual

Related papers

Other documents