Vax 2-in-1 Wet and Dry Multifunction Owner's manual

Brand: Vax

Model: 2-in-1 Wet and Dry Multifunction

Category: Vacuum cleaners

Type: Owner's manual

ECGAV1B1

LET’S GET STARTED.

Wet&Dry

VACUUMS FLOORS

TACKLES SPILLS

Let’s talk safety

Basic

safety

precautions

Don’ts

Do’s

This Wet & Dry vacuum is intended for household use only and NOT for

commercial or industrial use.

• Only use the Wet & Dry vacuum indoors and keep the area

you are cleaning well lit.

• Keep ngers, hair and loose clothing away from moving parts and

openings whilst using the Wet & Dry vacuum.

• The Wet & Dry vacuum should be positioned at on the oor when

starting and during use. To prevent dirty water running into the motor

do not use the Wet & Dry vacuum upside-down or on its side.

• Don’t use the Wet & Dry vacuum if it has been dropped, damaged

or left outdoors.

• Don’t attempt to remove blockages with sharp objects as this may

cause damage to your Wet & Dry vacuum.

• Don’t run over the power cord or use the Wet & Dry vacuum

if the power cord or plug is damaged. Please contact our Customer

Service on: 0330 026 8455.

• Don’t vacuum up any ammable or combustible materials (lighter uid,

petrol, kerosene etc.) or use the Wet & Dry vacuum in an area with

explosive vapours or liquid.

• Don’t handle the plug or use the Wet & Dry vacuum with wet hands.

• Turn o all controls on the Wet & Dry vacuum before disconnecting

or connecting the power cord.

• Always make sure the lter and lter bag are in place before use.

• Always check accessories are free from damage, dirt and debris

before use.

• Always switch o the Wet & Dry vacuum before disconnecting

or connecting the hose and accessories.

• Keep all openings clear and free from debris as this may aect

the airow/suction.

• Always replace the fuse in the plug with a British 13amp fuse. Always

protect the power cord from heated surfaces or near open ames.

• Take extra care when positioning and using the Wet & Dry vacuum

on the stairs.

• This Wet & Dry vacuum can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved. Children shall not

play with the Wet & Dry vacuum. Cleaning and user maintenance shall not be made

by children without supervision.

• Only Vax recommended tools and accessories should be used with this

Wet & Dry vacuum.

• Don’t vacuum up hard or sharp objects such as glass, nails, screws

or coins etc.

• Don’t vacuum up hot coals, cigarette butts, matches or smoking hot burning items

or use in an area where there may be harmful uids (chlorine, bleach, and ammonia

drain cleaner).

• Don’t pull or carry the Wet & Dry vacuum by the power cord. Don’t use the power

cord as a handle, pull the power cord around corners, sharp edges or close a door

over the power cord. Don’t unplug the Wet & Dry vacuum by pulling on the power cord.

• Don’t use the Wet & Dry vacuum with incorrect voltage as this may result in damage

or injury to the user. The correct voltage is listed on the ratings label.

• Use only CE approved 13amp extension cords, non-approved extension cords may

overheat. Care should be taken to arrange the extension cord as it can be a trip hazard.

• Before storing the tank, the lter and lter bag must be thoroughly clean and dry as per

the user guide instructions. Store the Wet & Dry vacuum in a cool, dry area.

PLEASE KEEP INSTRUCTIONS FOR FURTHER USE.

Thank you for buying this Wet & Dry.

Taking care of your carpets

The Wet & Dry is designed to make vacuuming and sucking up spills regularly, as eective and

ecient as possible and this user guide will help you get the most out of your machine.

Taking care of your Wet & Dry

Also inside this guide are instructions on maintaining your new machine, so that it’s always

ready when you are to tackle dirt and debris.

Let us know what you think @VaxUK

Taking care of you

We’re here if you need us. Instead of taking me back

to the shop, simply visit our online support:

vax.co.uk/support

Still need to get in touch?

Our UK based Customer Care Team are here to support you - for help with assembly,

operational/performance problems or buying and tting new accessories. Whether you wish to chat,

use Facebook, Twitter or call, you can nd all our contact details at vax.co.uk/contactus

This user guide can be found online at: vax.co.uk/support

Contents

Included with

your machine

Let’s talk safety

Getting to know your machine

Getting started

Using your machine

Taking care of your machine

What to do if it goes wrong

Getting in touch

Wet & Dry

Accessory Hose and Grip

Extension Tubes

Crevice Tool

Wet Pick Up Tool

Combination Floorhead

Wet & Dry Upholstery Tool

Getting to know your machine

Name Wet & Dry

Code ECGAV1B1

Part number 1-1-138767

Voltage 220-240V-50~60Hz

Wattage 1400W

Cord length 10m

Weight 7kg

Technical Specication

Subject to technical change without notice.

Blower port (hidden)

Post motor grill and lter

Lid release clips

Upper power cord hook

Lower power

cord hook

Tool storage

Carry handle

On/O switch

Filter bag (hidden)

Float (hidden)

Tank

Hose

connection

PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE

Getting started

Before you begin

• WARNING: Always switch o the Wet & Dry vacuum before connecting or disconnecting the hose/attachments,

or emptying the tank.

• IMPORTANT: The Wet & Dry vacuum is equipped with a thermal cut-out. If for any reason the Wet & Dry vacuum

does overheat, the thermostat will automatically turn the Wet & Dry vacuum o. If this happens, switch the Wet &

Dry vacuum o and unplug. Empty the tank and also check the Wet & Dry vacuum for blockages. Allow the Wet &

Dry vacuum to cool for approximately 24 hours (if you have cleaned the lter and lter bag please wait 24 hours for

the lter and lter bag to fully dry before putting back into the Wet & Dry vacuum). For best cleaning results the lter

and lter bag require cleaning after every use and replacement every 6 months. If the Wet & Dry vacuum is blocked,

switch o and unplug before removing the blockage.

Assembling your Wet & Dry vacuum

Push the hose rmly into the

hose connection and twist to

lock into place.

Push the other end of the

extension tube onto the

desired accessory.

Insert the hose grip on to

extension tube.

Additional tools can be stored

on the back of the vacuum.

Push together the 2

extension tubes.

Using your machine

• IMPORTANT: The Wet & Dry vacuum should be positioned at on the oor when starting and during use to prevent

dirty water running into motor. Do not use the Wet & Dry vacuum upside-down or on its side. Always make sure

both the lter and lter bag are in place before use.

Using as a Wet & Dry vacuum

Attach the combination tool

to the extension tube.

Slide vent cover on hose grip

open to reduce suction

if required.

Plug into mains and press

the on/o switch to the I

position to switch on.

Raise brushes for use on

carpets. Lower brushes for

use on hardoor.

Using your machine

Using the accessories

TIP

Brushes on the oor

head should be visible

when using on

hard oors.

TIP

For best cleaning

performance always

empty before and after

using for wet pick up.

Using for wet pick up

• IMPORTANT: The Wet & Dry vacuum is tted with a oat. When the tank is full, the oat will shut o the suction to

the vacuum. You will be able to hear if this has happened as the motor noise will increase. Once the oat is activated,

switch o the Wet & Dry vacuum and empty the dirty water. If the tank is not full, then turn o the Wet & Dry vacuum

at the power switch and wait for the oat under the lid to settle. Always makes sure the oat is able to move freely

prior to use.

Choose an accessory and push

onto the hose grip or

extension tube.

Plug into mains and press

the on/o switch to the

I position to switch on.

Choose an accessory and push onto the hose grip or

extension tube.

Using your machine

• IMPORTANT: The Wet & Dry vacuum should be positioned at on the oor when starting and in use.

Using blow function

Unclip the grill and lter and remove. Push the hose rmly into the blower port and twist to lock

into place.

Plug into mains and press

the on/o switch to the

I position to switch on.

Taking care of your machine

Emptying and cleaning the tank after dry pick up

Lift and unhook the clips to

remove the lid.

Lift out the lter bag from the tank and tap against a bin to remove

the dirt and debris.

Empty the tank. Use a damp

cloth to remove any dirt

and debris.

TIP

The lid will not t correctly if the lter bag is not in place.

Emptying and cleaning the tank after wet pick up

Lift and unhook the clips to

remove the lid.

Lift out the lter bag from the tank and tap against a bin to remove

the dirt and debris.

Empty the tank, rinse with

warm water (Max 40˚C)

to remove dirt/debris and

wipe dry.

Taking care of your machine

Cleaning the lter bag

Cleaning the post-motor lter

Lift and unhook the clips to

remove the lid.

Unclip the grill and lter

and remove.

Lift out the lter bag from the tank and tap against a bin to remove

the dirt and debris.

Separate the foam lter from

the grill.

Tap the lter against a bin to

remove the dirt and debris.

Rinse under a warm tap max

40°c, allow to fully dry

before replacing into the

Wet & Dry vacuum.

TIP

For best cleaning results clean the lter bag after every use and replace every 6 months.

Rinse under a warm tap

max 40°c allow to fully dry

before replacing into the

Wet & Dry vacuum.

Cleaning the wet pick up tool

Storage

Push the clips to remove the brush and squeegee.

Taking care of your machine

Slide the squeegee out of the

tool and wipe clean with a

damp cloth.

The brush can be washed

(max 40°c).

Before storing, the Wet & Dry vacuum, the lter and lter bag must be thoroughly clean and dry.

Store the Wet & Dry vacuum in a cool, dry area.

Release the upper cord hook from the handle and wind the cord

to store.

TIP

Close the upper cord

hook when not being

used to store the cord.

Power cord storage

• Check the ‘This pack contains’ panel on the box to make sure the part is included

with your Wet & Dry vacuum.

• The lid may not be correctly tted, remove the lid from the Wet & Dry vacuum

and ret ensuring it’s locked into place. The lid will not t correctly if the lter bag

is not in place.

• The lter or lter bag may be clogged. To clean the lter or lter bag go to ‘Taking

care of your machine’.

• The tank maybe full, empty the tank. Go to ‘Taking care of your machine’.

• There may be a blockage in the hose/tube. Disconnect from the Wet & Dry vacuum

and carefully remove any blockages.

• Float may be stuck in the upright position. The Wet & Dry vacuum is tted with a

oat. When the tank is full, the oat will shut o the suction to the vacuum. You will

be able to hear if this has happened as the motor noise will increase. Once the oat

is activated, switch o the Wet & Dry vacuum and empty the tank. If the tank is not

full, then turn o the Wet & Dry vacuum at the power switch and wait for the oat

under the lid to settle.

SolutionProblem

What to do if it goes wrong

Is there an

accessory missing?

Why won’t the

Wet & Dry vacuum

pick up?

Why won’t the blower

function work?

• The tank may be full, empty the tank. Go to ‘Taking care of your machine’.

• The lter may be clogged. To clean the lter go to ‘Taking care of

your machine’.

• Hose may be incorrectly tted, ret. Go to ‘Using your machine’.

• There may be a blockage in the hose/tube. Disconnect from the Wet & Dry vacuum

and carefully remove any blockages.

Why does my

Wet & Dry vacuum

have no power?

• The plug may not be fully pushed into the electrical socket.

• Check the fuse in the plug. If this needs replacing, always replace with a 13amp fuse.

• The motor thermostat may have tripped. If this has happened, unplug the Wet & Dry

vacuum. Empty the tank and check the hose for blockages. Clean the lter and lter

bag and allow the Wet & Dry vacuum to cool for approximately 1 hour (if you have

washed the lter and lter bag you will need to wait 24 hours for them to fully dry

before putting them back into the Wet & Dry vacuum).

Why is dust

escaping from the

Wet & Dry vacuum?

• The lter and lter bag may be clogged. To clean the lter and/or lter bag go to

‘Taking care of your machine’.

• IMPORTANT: Unplug and switch o Wet & Dry vacuum before performing maintenance or troubleshooting checks.

Getting in touch

†

Registration required. Terms and conditions apply, see vax.co.uk for details.

GET IN TOUCH

0330 026 8455 VaxVacuums[email protected] vax.co.uk @VaxUK

EU Statement of Compliance: Manufacturer/EU importer: Vax Limited, hereby on our own responsibility, declare that the

ECGAV1B1 is manufactured in compliance with the following Directives: Safety: 2014/35/EU Low Voltage Directive.

EMC: 2014/30/EU Electromagnetic Compatibility Directive.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your

Local Authority or retailer for recycling advice.

Technology Ltd and is registered in the EU and may be pending or registered in other countries.

Vax 2-in-1 Wet and Dry Multifunction Owner's manual

Brand: Vax

Model: 2-in-1 Wet and Dry Multifunction

Category: Vacuum cleaners

Type: Owner's manual

Download PDF

report

Vax 2-in-1 Wet and Dry Multifunction Owner's manual

Vax 2-in-1 Wet and Dry Multifunction Owner's manual

Related papers

Other documents