LG FH0C9CDHK72 Owner's manual

www.lg.com

Made in Korea

OWNER’S MANUAL

WASHING

MACHINE

Before beginning installation, read these instructions carefully.

This will simplify installation and ensure that the product is installed

correctly and safely. Leave these instructions near the product after

installation for future reference.

FH0C9CDHK72

ENGLISH

MFL69283960

TABLE OF CONTENTS

This manual is produced for a group of products

and may contain images or content different from

the model you purchased.

This manual is subject to revision by the

manufacturer.

SAFETY INSTRUCTIONS ......................................03

Important Safety Instructions ...............................................................05

INSTALLATION .......................................................08

Specifications ......................................................................................08

Accessories

.........................................................................................08

Installation Place Requirements

.......................................................... 09

Unpacking and Removing Shipping Bolts

...........................................10

Using Non-Skid Pads (Optional).......................................................... 11

Wooden Floors (Suspended Floors)

.................................................... 11

Leveling the Washing Machine

............................................................12

Connecting Inlet Hose

.........................................................................12

Installation of Drain Hose

....................................................................15

OPERATION ...........................................................16

Using the Washing Machine ................................................................ 16

Sorting Iaundry

....................................................................................17

Adding Cleaning Products

................................................................... 18

Control Panel

.......................................................................................20

Programme Table

................................................................................21

Option Cycle

........................................................................................ 25

Dry

.......................................................................................................29

SMART FUNCTIONS ..............................................30

Application Installation .........................................................................30

Using the Wi-Fi Function

.....................................................................30

Open Source Software Notice Information

.......................................... 31

Using the Smart Diagnosis™ Function................................................31

MAINTENANCE ......................................................33

Cleaning your Washing Machine ......................................................... 33

Cleaning the Water Inlet Filter

.............................................................33

Cleaning the Drain Pump Filter

...........................................................34

Cleaning the Dispenser

......................................................................35

Tub Clean

............................................................................................35

Caution on Freezing During Winter

.....................................................36

TROUBLESHOOTING ............................................38

Diagnosing Problems ..........................................................................38

Error Messages

...................................................................................40

WARRANTY ............................................................42

03

ENGLISH

SAFETY INSTRUCTIONS

The following safety guidelines are intended to prevent unforeseen risks or

damage from unsafe or incorrect operation of the product.

The guidelines are separated into ‘WARNING’ and ‘CAUTION’ as described

below.

This symbol is displayed to indicate matters and operations that can

cause risk. Read the part with this symbol carefully and follow the

instructions in order to avoid risk.

WARNING

- This indicates that the failure to follow the instructions

can cause serious injury or death.

CAUTION

- This indicates that the failure to follow the instructions

can cause the minor injury or damage the product.

To reduce the risk of re, electric shock, or injury to persons when using

your product, basic safety precautions should be followed, including the

following.

WARNING

CHILDREN IN THE HOUSEHOLD

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety. Children should be supervised to ensure that they do

not play with the appliance.

For use in Europe:

This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

Children of less than 3 years should be kept away unless continuously supervised.

04

GROUNDING REQUIREMENTS

For your safety, the information in this manual must be followed to

minimize the risk of re, explosion, or electric shock, or to prevent

property damage, injury to persons, or death.

WARNING

•

This appliance must be grounded. In the event of malfunction or breakdown, grounding

will reduce the risk of electric shock by providing a path of least resistance for electric

current.

•

This appliance is equipped with a cord having an equipment-grounding conductor and

grounding plug. The plug must be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances.

•

Improper connection of the equipment-grounding conductor can result in risk of electric

shock. Check with a qualied electrician or service person if you are in doubt as to

whether the appliance is properly grounded.

•

Do not modify the plug provided with the appliance. If it does not t the outlet, have a

proper outlet installed by a qualied electrician.

05

ENGLISH

Important Safety Instructions

To reduce the risk of re, electric shock, or injury to persons when using

your product, basic safety precautions should be followed, including the

following.

WARNING

Operation

•

Do not use a sharp object like drill or pin

to press or separate an operation unit. It

can cause the electric shock or injury.

•

Only an authorized repair person from

LG Electronics service centre should

disassemble, repair, or modify the

product. Improper service may cause

injury, electric shock or re.

•

Do not spray the water inside or outside

the product to clean it. Water can

damage the insulation, causing electric

shock or re.

•

Keep the area underneath and around

your appliances free of combustible

materials such as lint, paper, rags,

chemicals, etc. Improper use can cause

re or explosion.

•

Do not put living animals, such as pets

into the product. It may cause injury.

•

Do not leave this appliance door open.

Children may hang on the door or crawl

inside the appliance, causing damage

or injury.

•

Never reach into this appliance while

it is operating. Wait until the drum has

completely stopped. Failure to do so

may result in injury.

Installation

•

Never attempt to operate this appliance

if it is damaged, malfunctioning, partially

disassembled, or has missing or broken

parts, including a damaged cord or plug.

It can cause electric shock or injury.

•

This appliance is heavy. Two or more

people may be needed to install and

move the appliance. Failure to do so

can result in injury.

•

Store and install this appliance where

it will not be exposed to temperatures

below freezing or exposed to outdoor

weather conditions. Failure to do so can

result in leakage.

•

Tighten the drain hose to avoid

separation. Splashing of water may

cause electric shock.

•

If the supply cord is damaged, it must

be replaced by the manufacturer or

its service agents or similarly qualied

person in order to avoid a hazard.

•

The appliance must not be installed

behind a lockable door, a sliding door or

a door with a hinge on the opposite side

to that of the tumble dryer, in such a way

that a full opening of the tumble dryer

door is restricted.the washing machine

shall not be installed at a humid place.

06

•

Do not put in, wash or dry articles that

have been cleaned in, washed in,

soaked in, or spotted with combustible

or explosive substances (such as

wax, oil, paint, gasoline, degreasers,

drycleaning solvents, kerosene,

vegetable oil, cooking oil, etc.). Improper

use can cause re or explosion.

•

In case of ood, stop using the product

and contact the LG Electronics service

centre. Contact with water can cause

electric shock.

•

Do not push down the door excessively,

when the appliance door is open. Doing

so may topple over the appliance and it

can cause the injury.

•

Use new hose-sets supplied with the

appliance. Old hose-sets should not

be reused. Water leakage may cause

property damage.

•

Do not touch the door during steam

cycles, drying or high-temperature

washing. The door surface can become

very hot. Allow the door lock to release

before opening the door. Failure to do

so may result in injury.

•

Do not use inammable gas and

combustible substances (benzene,

gasoline, thinner, petroleum, alcohol,

etc.) around the product. It may cause

explosion or re.

•

If the drain hose or inlet hose is frozen

during winter, use it only after thawing.

Freezing may cause re or electric

shock, and frozen parts may cause

product malfunction or reduction in

product life span.

•

Keep all washing detergents, softener

and bleach away from children. These

products contain poisonous materials.

•

Do not plug multiple products into

multiple socket-outlets or extension

cords. This can cause re.

•

Remove the power plug when you clean

the product. Not removing the plug may

result in electric shock or injury.

•

Do not touch the power plug with wet

hands. It can cause the electric shock

or injury.

•

When pulling out the power plug from

an outlet, hold the power plug, not the

cable. Damage of the cable can cause

the electric shock or injury.

•

Do not bend the power cable

excessively or place a heavy object on

top of it. Damage of the power cable

can cause electric shock or re.

07

ENGLISH

Disposal

•

Before discarding an old appliance,

unplug it. Render the plug useless.

Cut off the cable directly behind the

appliance to prevent misuse.

•

Dispose of the packaging material (such

as vinyl and styrofoam) away from

children. The packaging material can

suffocate a child.

•

Remove the door to the washing

compartment before this appliance is

removed from service or discarded to

avoid the danger of children or small

animals getting trapped inside. Failure

to do so can result in serious injury to

persons or death.

Technical Safety for Using the

Tumble Dryer

•

Do not dry unwashed items in the

appliance.

•

Items that have been soiled with

substances such as cooking oil,

vegetable oil, acetone, alcohol, petrol,

kerosene, spot removers, turpentine,

waxes and wax removers should be

washed in hot water with an extra

amount of detergent before being dried

in the appliance.

•

Fabric softeners or other similar

products should be used according to

the fabric softener instructions.

•

Remove all objects from pockets such

as lighters and matches.

•

Never stop this appliance before the

end of the drying cycle unless all items

are quickly removed and spread out so

that the heat is dissipated.

•

This appliance is not to be used if

industrial chemicals have been used for

cleaning.

•

Items such as foam rubber (latex foam),

shower caps, waterproof textiles, rubber

backed articles and clothes or pillows

tted with foam rubber pads should not

be dried in this appliance.

08

INSTALLATION

Specications

Transit bolts

Power plug

Detergent

dispenser

Control panel

Drum

Door

Drain hose

Drain plug

Drain pump lter

Cover cap

(Location may

vary depending on

products)

Adjustable feet

•

Power supply : 220-240 V~, 50 Hz

•

Size : 700 mm (W) x 835 mm (D) x 990 mm (H)

•

Product weight : 105 kg

•

Wash Capacity : 21 kg (Wash) / 12 kg (Dry)

•

Permissible water pressure : 0.1 - 1.0 MPa (1.0 - 10.0 kgf / cm

2

)

•

IP No.(Degree of Protection) : IPX4

•

Appearance and specications may vary without notice to improve the quality of the

product.

Accessories

Inlet hose (1EA)

(Option : Hot

(1EA))

Spanner Elbow Bracket

(for securing

drain hose)

Anti–slip sheets

(2EA)

(Optional)

Caps for covering

shipping bolt

holes

Tie strap Grounding

conductor

09

ENGLISH

Installation Place Requirements

Location

2.5 cm

10 cm80.2 cm

139.6 cm

59.4 cm

Level oor :

Allowable slope under the entire washing

machine is 1°.

Power outlet : Must be within 1.5 meters of either side

of the location of the washing machine.

•

Do not overload the outlet with more than one

appliance.

Additional Clearance : For the wall, 10 cm: rear

/2.5 cm: right & left side

•

Do not place or store laundry products on top of the

washing machine at any time.

•

These products may damage the nish or controls.

Positioning

•

Install the washing machine on a at hard oor.

•

Make sure that air circulation around the washing

machine is not impeded by carpets, rugs, etc.

•

Never try to correct any unevenness in the oor with

pieces of wood, cardboard or similar materials under

the washing machine.

•

If it is impossible to avoid positioning the washing

machine next to a gas cooker or coal burning

insulation (85x60 cm) covered with aluminum foil on

the side facing the cooker or stove must be inserted

between the two appliances.

•

Do not install your washing machine in rooms where

freezing temperatures may occur. Frozen hoses may

burst under pressure. The reliability of the electronic

control unit may be impaired at temperatures below

freezing point.

•

Please ensure that when the washing machine is

installed, it is easily accessible for an engineer in the

event of a breakdown.

•

With the washing machine installed, adjust all four feet

using the transit bolt spanner provided to ensure the

appliance is stable, and a clearance of approximately

20 mm is left between the top of the washing machine

and the underside of any work-top.

•

This equipment is not designed for maritime use or for

use in mobile installations such as caravans, aircraft

etc.

Electrical Connection

•

Do not use an extension cord or double adapter.

•

Always unplug the washing machine and turn off the

water supply after use.

•

Connect the washing machine to an earthed socket in

accordance with current wiring regulations.

•

The washing machine must be positioned so that the

plug is easily accessible.

•

Repairs to the washing machine must only be carried

out by qualied personnel. Repairs carried out by

inexperienced persons may cause injury or serious

malfunctioning. Contact your local service centre.

•

If the washing machine is delivered in winter and

temperatures are below freezing, place the washing

machine at room temperature for a few hours before

putting it into operation.

10

Unpacking and Removing

Shipping Bolts

1

Lift the washing machine off the foam base.

•

After removing the carton and shipping material,

lift the washing machine off the foam base. Make

sure the tub support comes off with the base

and is not stuck to the bottom of the washing

machine.

•

If you must lay the washing machine down to

remove the carton base, always protect the side

of the washing machine and lay it carefully on

its side. DO NOT lay the washing machine on its

front or back.

Tub Support

(Optional)

Carton base

2

Remove the bolt assemblies.

•

Starting with the bottom two shipping bolts, use

the spanner (included) to fully loosen all shipping

bolts by turning them counterclockwise. Remove

the bolt assemblies by wiggling them slightly

while pulling them out.

Retainer

Shipping

bolt

3

Install the hole caps.

•

Locate the hole caps included in the accessory

pack and install them in the shipping bolt holes.

Cap

NOTE

•

Save the bolt assemblies for future use. To

prevent damage to internal components, DO NOT

transport the washing machine without reinstalling

the shipping bolts.

•

Failure to remove shipping bolts and retainers

may cause severe vibration and noise, which

can lead to permanent damage to the washing

machine. The cord is secured to the back of the

washing machine with a shipping bolt to help

prevent operation with shipping bolts in place.

11

ENGLISH

Using Non-Skid Pads (Optional)

If you install the washing machine on a slippery surface,

it may move because of excessive vibration. Incorrect

leveling may cause malfunction through noise and

vibration. If this occurs, install the non-skid pads under

the leveling feet and adjust the level.

1

Clean the oor to attach the non-skid pads.

•

Use a dry rag to remove and clean foreign

objects and moisture. If moisture remains, the

non-skid pads may slip.

2

Adjust the level after placing the washing machine

in the installation area.

3

Place the adhesive side of the non-skid pad on the

oor.

•

It is most effective to install the non-skid pads

under the front legs. If it is difcult to place the

pads under the front legs, place them under the

back legs.

This side up

Adhesive side

4

Ensure the washing machine is level.

•

Push or rock the top edges of the washing

machine gently to make sure that the washing

machine does not rock. If the washing machine

rocks, level the washing machine again.

Wooden Floors (Suspended

Floors)

•

Wooden oors are particularly susceptible to vibration.

•

To prevent vibration we recommend you place rubber

cups at least 15 mm thick of the each foot of the

washing machine, secured to at least two oor beams

with screws.

Rubber Cup

•

If possible install the washing machine in one of the

corners of the room, where the oor is more stable.

•

Fit the rubber cups to reduce vibration.

•

You can obtain rubber cups (p/no.4620ER4002B) from

the LG Service Centre.

NOTE

•

Proper placement and leveling of the washing

machine will ensure long, regular, and reliable

operation.

•

The washing machine must be 100% horizontal

and stand rmly in position.

•

It must not ‘Seesaw’ across corners under the

load.

•

The installation surface must be clean, free from

oor wax and other lubricant coatings.

•

Do not let the feet of the washing machine get

wet. Failure to do so may cause vibration or noise.

12

Leveling the Washing Machine

If the oor is uneven, turn the adjustable feet as required

(Do not insert pieces of wood etc. under the feet). Make

sure that all four feet are stable and resting on the oor

and then check that the appliance is perfectly level (Use

a spirit level).

•

Once the washing machine is level, tighten the lock

nuts up towards the base of the washing machine. All

lock nuts must be tightened.

Raise

Lock Nut

Lower

Tighten all 4

locknuts securely

•

Diagonal Check

When pushing down the edges of the washing

machine top plate diagonally, the washing machine

should not move up and down at all (Check both

directions). If the washing machine rocks when

pushing the machine top plate diagonally, adjust the

feet again.

NOTE

•

Timber or suspended type ooring may contribute

to excessive vibration and unbalance.

•

If the washing machine is installed on a raised

platform, it must be securely fastened in order to

eliminate the risk of falling off.

Connecting Inlet Hose

•

Water supply pressure must be between 0.1 MPa and

1.0 MPa (1.0 ‒ 10.0 kgf/cm

2

).

•

Do not strip or crossthread when connecting inlet hose

to the valve.

•

If the water supply pressure is more than 1000 kPa, a

decompression device should be installed.

•

Periodically check the condition of the hose and

replace the hose if necessary.

Checking Rubber Seal Inlet Hose

Two rubber seals are supplied with the water inlet hoses.

They are used for preventing water leaks. Make sure the

connection to taps is sufciently tight.

Hose connector

Rubber seal

Hose connector

Rubber seal

13

ENGLISH

Connecting Hose to Water Tap

Connecting screw-type hose to tap with thread

Screw the hose connector onto the water supply tap.

Connecting screw-type hose to tap without

thread

1

Loose the four xing screws.

Upper

connector

Rubber

seal

Fixing screw

2

Remove the guide plate if the tap is too large to t

the adapter.

Guide plate

3

Push the adapter onto the end of the tap so that

the rubber seal forms a watertight connection.

Tighten the four xing screws.

4

Push the inlet hose vertically upwards so that the

rubber seal within the hose can adhere completely

to the tap and then tighten it by screwing it to the

right.

Plate

Inlet hose

Connecting one touch type hose to tap without

thread

1

Unscrew the adapter ring plate and loose the four

xing screws.

Ring plate

2

Remove the guide plate if the tap is too large to t

the adapter.

Guide plate

14

3

Push the adapter onto the end of the tap so that

the rubber seal forms a watertight connection.

Tighten the adapter ring plate and the four xing

screws.

4

Pull the connector latch plate down, push the inlet

hose onto the adapter, and release the connector

latch plate. Make sure the adapter locks into place.

Latch plate

NOTE

•

After connecting the inlet hose to the water

tap, turn on the water tap to ush out foreign

substances (dirt, sand, sawdust, etc.) in the water

lines. Let the water drain into a bucket, and check

the water temperature.

Connecting Hose to Washing Machine

Make sure that there are no kinks in the hose and that

they are not crushed.

When your washing machine has two valves.

•

The Inlet hose with the red connector is for the hot

water tap.

NOTE

•

After completing connection, if water leaks from

the hose, repeat the same steps.

Use the most conventional type of tap for the

water supply

. In case the tap is square or too big,

remove the guide plate before inserting the tap

into the adaptor.

Using the horizontal tap

Horizontal tap

Extension tap

Square tap

15

ENGLISH

Installation of Drain Hose

•

The drain hose should not be placed higher than 100

cm above the oor. Water in the washing machine

may not drain or may drain slowly.

•

Securing the drain hose correctly will protect the oor

from damage due to water leakage.

•

If the drain hose is too long, do not force it back into

the washing machine. This will cause abnormal noise.

about 100 cm

about 145 cm

max. 100 cm

about 105 cm

•

When installing the drain hose to a sink, secure it

tightly with string.

•

Securing the drain hose correctly will protect the oor

from damage due to water leakage.

Laundry tub

Hose

retainer

max. 100 cm

Tie strap

max. 100 cm

16

OPERATION

Using the Washing Machine

Before the rst wash, select a cycle (Cotton 60 °C, add

a half load of detergent), allow the washing machine

to wash without clothing. This will remove residue and

water from the drum that may have been left during

manufacturing.

1

Sort laundry and load items.

•

Sort laundry by fabric type, soil level, colour and

load size as needed. Open the door and load

items into the washing machine.

2

Add cleaning products and/or detergent and

softener.

•

Add the proper amount of detergent to the

detergent dispenser. If desired, add bleach or

fabric softener to the appropriate areas of the

dispenser.

3

Turn on the washing machine.

•

Press the Power button to turn ON the washing

machine.

4

Choose the desired washing cycle.

•

Press the Cycle button repeatedly or turn the

cycle selector knob until the desired cycle is

selected.

5

Begin cycle.

•

Press the Start/Pause button to begin the cycle.

The washing machine will agitate briey without

water to measure the weight of the load. If the

Start/Pause button is not pressed within 5

minutes, the washing machine will shut off and

all settings will be lost.

6

End of cycle.

•

When the cycle is nished, a melody will sound.

Immediately remove your clothing from the

washing machine to reduce wrinkling. Check

around the door seal when removing the load for

small items that may be caught in the seal.

17

ENGLISH

Sorting Iaundry

1

Look for a care label on your clothes.

•

This will tell you about the fabric content of your

garment and how it should be washed.

•

Symbols on the care labels.

Wash temperature

Normal machine wash

Permanent press

Delicate

Hand wash

Do not wash

2

Sorting laundry.

•

To get the best results, sort clothes into loads

that can be washed with the same wash cycle.

•

Different fabrics need to be washed at varying

temperatures and spin speeds.

•

Always sort dark colours from pale colours and

whites. Wash separately as dye and lint transfer

can occur causing discolouration of white and

pale garments. If possible, do not wash heavily

soiled items with lightly soiled ones.

– Soil (Heavy, Normal, Light)

Separate clothes according to amount of soil.

– Colour (White, Lights, Darks)

Separate white fabrics from coloured fabrics.

– Lint (Lint producers, Collectors)

Wash lint producers and lint collectors

separately.

3

Caring before loading.

•

Combine large and small items in a load. Load

large items rst.

•

Large items should not be more than half the

total wash load. Do not wash single items. This

may cause an unbalanced load. Add one or two

similar items.

•

Check all pockets to make sure that they are

empty. Items such as nails, hair clips, matches,

pens, coins and keys can damage both your

washing machine and your clothes.

•

Close zippers, hooks and strings to make sure

that these items don’t snag on other clothes.

•

Pre-treat dirt and stains by brushing a small

amount of detergent dissolved water onto stains

to help lift dirt.

•

Check the folds of the exible gasket (gray) and

remove any small articles.

•

Check inside the drum and remove any items

from a previous wash.

•

Remove any clothing or items from the exible

gasket to prevent clothing and gasket damage.

18

Adding Cleaning Products

Detergent Dosage

•

Detergent should be used according to the instruction

of the detergent manufacturer and selected according

to type, colour, soiling of the fabric and washing

temperature.

•

If too much detergent is used, too many suds can

occur and this will result in poor washing results or

cause heavy load to the motor.

•

If you wish to use liquid detergent follow the guidelines

provided by the detergent manufacturer.

•

You can pour liquid detergent directly into the main

detergent dispenser if you are starting the cycle

immediately.

•

Do not use liquid detergent if you are using Time

delay, or if you have selected Pre Wash, as the liquid

may harden.

•

If too many suds occur, reduce the detergent amount.

•

Detergent usage may need to be adjusted for water

temperature, water hardness, size and soil level of the

load. For best results, avoid oversudsing.

•

Refer to the label of the clothes, before choosing the

detergent and water temperature:

•

When using the washing machine, use designated

detergent for each type of clothing only:

– General powdered detergents for all types of fabric

– Powdered detergents for delicate fabric

– Liquid detergents for all types of fabric or

designated detergents only for wool

•

For better washing performance and whitening, use

detergent with the general powdered bleach.

•

Detergent is ushed from the dispenser at the

beginning of the cycle.

•

Do not place or store laundry products, such as

detergent, bleach, or liquid fabric softener, on top of

your washer or dryer. Wipe up any spills immediately.

These products can damage the machine's nish and

controls.

NOTE

•

Do not let the detergent harden.

Doing so may lead to blockages, poor rinse

performance or odour.

•

Full load : According to manufacturer’s

recommendation.

•

Part load : 3/4 of the normal amount

•

Minimum load : 1/2 of full load

Adding Detergent and Fabric Softener

Adding detergent

•

Main wash only →

•

Pre wash+Main wash →

NOTE

•

Too much detergent, bleach or softener may

cause an overow.

•

Be sure to use the appropriate amount of

detergent.

Adding fabric softener

•

Do not exceed the maximum ll line. Overlling can

cause early dispensing of the fabric softener, which

may stain clothes. Close the dispenser lid slowly.

NORMAL NORMAL

RMAL

19

ENGLISH

•

Do not leave the fabric softener in the detergent

dispenser for more than 2 days (Fabric softener may

harden).

•

Softener will automatically be added during the last

rinse cycle.

•

Do not open the dispenser lid when water is being

supplied.

•

Solvents (benzene, etc) should not be used.

NOTE

•

Do not pour fabric softener directly on the clothes.

Adding water softener

•

A water softener, such as Anti-limescale (e.g. Calgon)

can be used to cut down on the use of detergent in

extremely hard water areas. Dispense according to

the amount specied on the packaging. First add

detergent and then the water softener.

•

Use the quantity of detergent required for soft water.

MAX

NORMAL

•

To avoid injury, do not place ngers under the lid

or between the lid and the top plate when pressing

or sliding the detergent dispenser lid open or

closed.

Using tablet

1

Open the door and put tablets into the drum.

2

Load the laundry into the drum and close the door.

CAUTION

20

Control Panel

Power button

•

Press the Power button to turn the washing

machine on.

•

Press and hold the Power button for 1 second

to turn the washing machine off.

Start/Pause button

•

This Start/Pause button is used to start the

wash cycle or pause the wash cycle.

•

If a temporary stop of the wash cycle is needed,

press the Start/Pause button.

Display

•

The display shows the settings, estimated

time remaining, options, and status messages.

When the product is turned on, the default

settings in the display will illuminate.

•

The display shows estimate time remaining.

While the size of the load is being calculated

automatically, blinking

or ‘Detecting’

appears.

Programme button

•

Programmes are available according to laundry

type.

•

Lamp will light up to indicate the selected

programme.

Options

•

This allows you to select an additional cycle

and will light when selected.

•

Use these buttons to select the desired cycle

options for the selected cycle.

Page is loading ...

LG FH0C9CDHK72 Owner's manual

LG FH0C9CDHK72 Owner's manual

Other documents