Orbit Max2 Owner's manual

OWNER’S MANUAL

CAUTION: Exercise of a strenuous nature as is customarily done on this equipment, should not be undertaken without rst

consulting a physician before beginning any exercise program.

No specic health claims are made or implied as they relate to the equipment.

IMPORTANT: Read all assembly instructions and safety precautions carefully in the Owners manual before using this product.

Reference all safety guidelines and warning labels. Retain this products Owners Manual for future references.

SAFETY: Always warm up your muscles before starting a workout. Stretching should be performed in both the warm

up and cool down phases of a training program. Should you feel dizziness at any time while exercising, stop

immediately and consult your physician.

• Warranty

• Assembly

• Parts

TOOLS REQUIRED

FOR ASSEMBLY

- Adjustable Wrench

- Pliers

- Hammer

1

Catalogue

Catalogue------------------------------------------------------------------ 1

Warning-------------------------------------------------------------------- 1

Assembling steps -----------------------------------------------------2-15

Exploded view ------------------------------------------------------16-17

Parts list --------------------------------------------------------------18-22

Daily Maintenance------------------------------------------------------22

Warning

1. Before exercise, please check to make sure all bolts are tightened and handlebar welds are

intact.

2. Wear appropriate footwear during work out. Do not flip the handlebars during exercise.

3. When weight stack, suspender or other parts are caught, ask another person’s help to avoid the

sudden drop of weight stack.

4. Do not distort the cable when you adjust its length (tightness). After using for a period of time,

you should check if cable skin has worn out or the cable is badly stretched, contact the

serviceman to repair or replace as soon as you find problems.

5. Do not drop weight stacks all of a sudden to avoid damage and injury. You should always lower

the weight stacks slowly.

6. Do not insert hand and other parts of the body between/under weight stacks and other moving

parts to avoid injury.

7. Children under 16 should exercise under adult’s guidance.

8. People have special conditions (for example, aged or diseased) should always consult your

physician before starting exercise.

2

Assembling steps

1. Remove all parts out of boxes and place around area of installation! Place bolt packs in front of

the area where you want the gym.

2. Place part (2) in desired position, then connect part (3) with part (4) using bolts

(M10x75mm)(13), bolts (M10x80mm)(14), washers (26) and locknuts (23). Slide pulley limiting

board (17) through the leaderII (30), connecting to vertical tube (4) with hex bolts (M6x20mm)(1)

and washer(8) (25).

3

3. Connect backrest tube (5) to seat tube (3) with bolts (M10x75mm)(13) , washers (26) and

locknuts (23). Connect tube (1) to backrest tube (5) and vertical tube (4) with (M10x75mm)(13) ,

washers (26) and locknuts (23).

4

4. Insert leaders (10) into the oriented holes on the bottom of the curl base tube (2), in turn, slide

cover bumpers (51), rubber weight stack (48) and plastic top plate (46). Mount leader top tube(6)

to the leader (10) by washers (26) and bolts (M10x20mm)(5). Connect exercise chart flip (76),

leader top tube (6) and Lab pull down top tube (1) with bolts (M10x75mm)(13), washers (26)

and locknuts (23).

Attach shrouds (9) to the curl base tube (2) with washers (26) and bolts (M10x16mm)(4). Attach

handlebar tube (11) to the vertical tube (4) with washer (26) and bolt (M10x30mm)(7).

Attach plastic briquetting(46) to the leader(22) with bolt(M8x70mm)(8),washers(8)(25) and

locknut(M8)(22).

5

5. Connect backrest tube (5) and chest-extension rotating frame (7) through the rotating bearing

(25), tighten with Hexangular floriated bolt(M8*10mm) (30). Secure bearing bases (38), washers

(26) and bolts (M10x25mm)(6).

Attach chest-extension handlebars (8R&L) to the chest-extension rotating frame (7), which was

already attached to backrest tube (5) in step 4, with washers (26) and bolt (M10x30mm)(7). Slide

crossed bearing covers (29) to the chest-extension handlebars (8R&L), tighten with nut canopy (58).

Connect pulling bar (27R&L) and crossed bearing cover (29) through limiting bushing (31), bolt

(M12x120mm)(19), powder metallurgy bushing (74) ,flat washer (33),dish washer(32) and locknut

(24).

Attach chest-extension handlebars(8L&R) to the fixing tube(50) with bolt(M10x75)(13) and

locknut(M10)(23).

6

6.Connect the chest-extension frame (19), backrest tube (5) and pulley fixing frame (26) with bolts

(M10x70mm)(12), bolts (M10x75mm)(13), washers (26) and locknuts (23). Fit chest-extension arm

(28), chest-extension adjusting board (33) to chest-extension frame (19) with locknut (24) and

powder metallurgy bushing (74),flat washer(12)(33),dish washer(12)(32),nut canopy(M12)(58).

7

7. Attach oriented hook (13) and zinc bushing(34)、separate ring(35) to seat tube (3) with bolt

(M10x90mm)(15), washer (26), flat washer (31) and locknut (23). Attach rubber cushion (56) to

the back of leg-kicking frame (39).

Connect seat tube (3) and leg-kicking frame (39) with powder metallurgy bushing (70), bolt

(M12x80mm)(18), washers (27) and locknut (24). Attach leg-extension connecting cover (37) to

leg-kicking frame (39) with powder metallurgy bushing (70), bolt (M12x70mm)(16), washers

(27) and locknut (24). Slide tube (79) through the leg-extension connecting cover (37), slide the

bolsters (61) onto both end of the tube, block with leg-kicking sofa hole covers (52) and plastic

briquetting (53).

Attach backrest adjusting bushing (18) to backrest tube (5) with bolt (M10x70mm)(12), washers

(26) and locknut (23). Connect narrow single pulley fork (12), pulley (73B) and pulley limiting

board (17) with bolt (M10x55mm) (10), washers (26) and locknut (23).

8

8. Wire circling way:

Cables to be installed in order cable (67) first, cable (63) second, cable (64) third, cable (66) fourth

and cable (65) last. View following 5 pages for figure diagrams.