Genesis HD-DNBC User manual

Genesis
Brand
Genesis
Model
HD-DNBC
Type
User manual
HIGH DEFINITION SERIAL DIGITAL INTERFACE
OSD CONTROL - USER’S GUIDE
CONTENTS
● FEATURES
● PRECAUTIONS
● PART AND FUNCTION
FRONT
LENS
CONNECTING THE CAMERA TO THE MONITOR
BACK
● CONNECTIONS
● CAMERA OPERATIONS
● TROUBLE SHOOTINGS
● SPECIFICATIONS
- 01 -
FEATURES
● HORIZONTAL RESOLUTION 1000 TV LINS
● DAY & NIGHT FUNCTION
● 3DDNR (3D DIGITAL NOISE REDUCTION)
● WDR (WIDE DYNAMIC RANGE)
● PRIVACY FUNCTION
● ADDITIONAL FUNCTION
● CONTROLLED OSD MENU
Sencor :1/3”Progressive Scan CMOS / Min.Illumination : 1 Lux at 1.2 / 0.1 Lux (B/W)
WHITE BAL, MOTION DETECTION, MIRROR, SHARPNESS, FREEZE, DZOOM,
SHADING, HLM, ACE Function are also available.
twenty-eight
- 02 -
PRECAUTIONS
- 03 -
PART & FUNCTION
BACK
CVBS : It is a video analog BNC connector.
HD-SDI : It is HD-SDI video signal output BNC connector.
- 05 -
LENS
CONNECTION
- 06 -
CONNECTION
- 07 -
CONNECTING POWER
CONNECTION
- 08 -
CONNECTING THE CAMERA TO THE MONITOR
CONNECTION
▶ Connect to use a converter when connect
HD-SDI output with general monitor.
▶ Video cable.
The cable to connect a video output of the camera and the monitor is BNC coaxial cable same
as the below. If the install distance between a camera and the monitor
is over the max video
transmission range, please use the separated video amplifier.
Max video transmission range
Recommended cable specification
100 ~140m
5C2V (75ohm)
200m
L-6CHD (75ohm)
(SDI exclusive cable)
- 09 -
CONNECTION
Using a RS-485 communication, it will be able to control the OSD menu
at the System Controller or DVR.
CONNECTING TO RS-485 CONTROL CABLE
When you construct external control systems for a camera control, please
use to the PROTOCOL or PELCO-D PROTOCOL.
When you connecting to RS-485 control cable, please peel off the outer
skin inside the RS-485 control cable.
485 Control Board Connection Port
(+) CONNECTION TERMINAL (R+)
(-) CONNECTION TERMINAL (R-)
RS-485 Control Port
485+
485-
RS-485 Communication establishment initial value
Item
Initial value
Camera ID
0
BAUD RATE
9600
UART MODE
8-NONE-1
RET PKT
Not supported
NOTES
(1) The case which it controls from the PC
Using a RS-485 converter, It connects to RS-485 control cable outside camera
and serial cable
EX) SERIAL PORT OF THE PC(COM1) → SERIAL CABLE → RS-485 CONVERTER
→ RS-485 CONTROL CABLE
(2) The case which it controls from the DVR or System Controller
It connects the RS-485 control cable in the connection terminal of 485 control
boards which are connected with the DVR or System Controller.
- 10 -
System Controller
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29

Genesis HD-DNBC User manual

Genesis
Brand
Genesis
Model
HD-DNBC
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents