Hitachi L46VN05U Instructions For Use Manual

Brand: Hitachi

Model: L46VN05U

Category: LCD TVs

Type: Instructions For Use Manual

Instructions for use

L46VN05U

46" LCD Colour Television

IMPORTANT - If placing TV into cabinet or alcove, ensure there is at least a 100mm (10cm) gap to the sides,

rear and top of the TV. This is to allow for adequate ventilation during operation. Please read the

main Users Guide for more safety information before installation.

insert the batteries into your handset

QUICK GUIDE

either connect the aerial straight to your TV...

...or connect the aerial through a VCR...

Aerial (RF) Socket

wall

socket

wall

socket

Aerial (RF)

Lead

Aerial (RF)

Lead

• It is recommended that a scart lead should be fitted between your TV and VCR to enhance your picture and sound

quality. Scart leads are essential if you have a stereo TV and VCR and wish to obtain stereo sound from your

equipment. These leads can be purchased from your

Hitachi dealer or any good High Street electrical retailer.

Rear view

ANT.IN

VCR

AV-1

AV-2

Aerial (RF) Socket

Optional Scart Lead

TV to VCR

(RF) connector

lead VCR to TV

Aerial (RF) Socket VCR

L46VN05U

...or through a VCR and satellite decoder.

ANT.IN

RF Lead to

Aerial

RF Lead

from VCR to

Satellite

RF Lead from

VCR to TV

Satellite LNB lead

Aerial

VCR

• Scart Lead to

AV on TV.-1

AV-1

TV VCR

AV-2

TFT-LCD TV

...or through a HDMI and YPBPR products (DVD-RW)

DVD RECORDER

COMPONENT

ANT.IN

ANTENNA

HDMI OUT

(RF) connector

lead Device to TV

wall

socket

Aerial (RF)

Lead

Aerial (RF) Socket

• High Definition

Your LCD Television is capable of displaying High Definition pictures from devices such as a High Definition Satellite Receiver or DVD

Device.These devices must be connected via the HDMI socket or Component Socket.

TFT-LCD TV

• Scart Lead to

AV on TV.-1

basic functions of remote control

connect the TV plug to the mains socket

switch your TV on

by setting the on/off button to position | .

NB: When the set is first switched on, the set will be in standby

. channel

and the indicator

on the front of the set will illuminate red Press Operate/Standby or

up down (P- , P+) or numeric buttons (1, 2, 3, ...) to

operate.

insert plug...

European

plug

...and switch on

insert plug...

UK plug

Programme Up

Volume Up

Volume Down

Programme Down

To enter the main menu

For navigation of the menus

SIDE

VIEW

Operate/Standby

SCREEN

LANG

SUBTITLE

PIP

RETURN

SOURCE FAV

PRESETS SLEEP

INFO

EPG

V+

V- P -

P+

RC 3900

Once the TV has found all your local stations, they are then automatically

assigned a programme number and name, if available from the broadcast.

important note.

start A.P.S. (Auto Programming System)

After APS is finalized, the programme table will appear on the screen. In the

programme list you will see the programme numbers and names assigned to

the programmes.

After Automatic Search process is completed, a message asking for

analogue channel search appears on the screen. To continue Auto Program,

first set the language, country and teletext language by using or button and

then press the RED or OK button

For details, please refer to the Install Menu section of the instruction book.

When the TV is turned on for the first time, the menu for the language selection

appears on the screen. The message “Welcome please select your

language!” is written in all language options sequentially in the menu on the

screen. By pressing

buttons highlight the language you want to set and

press OK. After then, First time Installation Menu will appear on screen. By

pressing

buttons, select country item you want to set and press OK button.

After the First Time Installation is set, the following message appears on the

screen.

To start automatic search, select “Yes”, to cancel select “No”. This process will

take about five minutes. To cancel searching, you can press “MENU ” button at

any time during the process.

Do you

want to start an automatic channel scan?

50112615

English - 1 -

Contents

Features ................................................................. 3

Introduction ............................................................. 4

Preparation ............................................................. 4

Safety Precautions ................................................. 4

Power Source ..................................................... 5

Power Cord ......................................................... 5

Warning .............................................................. 5

Disconnecting the Device ................................... 5

Moisture and Water ............................................ 5

Cleaning.............................................................. 5

Ventilation ........................................................... 5

Heat and Flames ................................................ 5

Lightning ............................................................. 5

Replacement Parts ............................................. 6

Servicing ............................................................. 6

Waste Disposal ................................................... 6

Information for Users in European Union Count-

ries ...................................................................... 6

Headphone Volume ............................................ 6

Installation........................................................... 6

LCD Screen ........................................................ 6

Overview of the Remote Control ............................ 7

LCD TV and Operating Buttons .............................. 8

Viewing the Connections- Back Connectors .......... 9

Aerial Connection ................................................. 12

Using the Cable Holder ........................................ 12

USB Memory Connection ................................. 13

Side HDMI Connection ......................................... 13

Inserting Batteries in the Remote Control Handset ...19

Operating Range for the Remote Control ............. 19

Switching the TV On/Off ....................................... 19

To Switch the TV On ......................................... 19

The TV will then switch on. ............................... 19

To Switch the TV Off ......................................... 19

Basic Operations .................................................. 20

Operation with the Buttons on the TV ............... 20

Volume Setting .............................................. 20

Programme Selection ................................... 20

Viewing Main Menu ....................................... 20

AV Mode ....................................................... 20

Operation with the Remote Control .................. 20

Volume Setting .............................................. 20

Programme Selection (Previous or Next Prog-

ramme) ......................................................... 20

Programme Selection (Direct Access) .......... 20

General Operation ................................................ 22

Information Banner ........................................... 22

Electronic Programme Guide (EPG) .................... 22

Displaying Subtitles .......................................... 23

Digital Teletext (** for UK only) ......................... 23

Analogue Teletext ............................................. 23

Widescreen ....................................................... 23

Channel List ...................................................... 24

Navigating the Entire Channel List ............... 24

Moving the channels in the channel list ........ 24

Deleting the Channels in the Channel List .... 24

Renaming Channels ..................................... 25

Adding Locks to Channels ............................ 25

Setting Favourites ......................................... 25

How to Add a Channel to a Favourites List 26

Removing a Channel from Favourite List 26

On Screen Help ........................................... 26

Program Guide ............................................. 26

Timers ............................................................... 26

Conditional Access ........................................... 26

TV Setup ........................................................... 27

Setup ................................................................ 27

Conﬁ guration ................................................ 27

Dolby D Digital (*for EU countries except

UK) .........................................................27

Hard of Hearing (*for EU countries except

UK) .........................................................27

Favourite Mode.......................................28

Channel List ...........................................28

Active Antenna .......................................28

Scan Encrypted (**) ...............................28

Receiver Upgrade ..................................28

Over Air Download (OAD) ......................28

Parental Control .....................................28

Maturity Lock (**) ................................. 29

Menu Lock ........................................... 29

Set PIN ................................................. 29

Time Settings (optional) ................................ 29

Audio Description .......................................... 29

Audio Description ...................................29

Preferred Language ...............................29

Relative Volume .....................................29

Standby Search (optional) (*) ....................... 30

Language ...................................................... 30

Preferred.................................................30

Current....................................................30

Language Settings .................................30

Installation ..................................................... 30

Automatic Channel Scan ........................31

Manual Channel Scan ............................31

Clear Service List (*)...............................31

First Time Installation..............................31

Media Browser .................................................. 32

Playing MP3 Files ............................................. 33

Viewing JPG Files ............................................. 33

Slideshow Options ............................................ 33

Video Playback ................................................. 34

Navigating the Analogue TV Menu System .......... 34

Analogue TV Menu System .................................. 34

Picture Menu..................................................... 34

Mode ............................................................. 34

Brightness/Contrast/Colour/Sharpness/Hue . 34

Colour Temp .................................................. 34

Noise Reduction ........................................... 35

Film Mode ..................................................... 35

English - 2 -

Game Mode .................................................. 35

Picture Zoom ................................................ 35

Reset ............................................................ 35

Store ............................................................. 35

Sound Menu ..................................................... 35

Volume .......................................................... 35

Equalizer ....................................................... 35

Balance ......................................................... 36

Headphone ................................................... 36

Volume....................................................36

Store ....................................................... 36

Sound Mode ................................................. 36

AVL ............................................................... 36

Effect ............................................................. 36

Store ............................................................. 36

Feature Menu ................................................... 36

Pip-Pap ...................................................37

Pip Size ..................................................37

PIP Position ............................................37

Source ....................................................37

Program ..................................................37

Swap.......................................................37

Sleep Timer ................................................... 37

Child Lock ..................................................... 37

Language ...................................................... 37

Default Zoom ................................................ 37

Blue Background .......................................... 37

Menu Background ......................................... 37

Power Save Mode ........................................ 37

Backlight ....................................................... 37

Menu Timeout ............................................... 37

Teletext Language ........................................ 38

HDMI PC Full Mode ...................................... 38

Full Mode (optional) ...................................... 38

Ext Out .......................................................... 38

Install Menu ...................................................... 38

Program ........................................................ 38

Band ............................................................. 38

Channel ........................................................ 38

Colour System .............................................. 38

Sound System .............................................. 38

Fine Tune ...................................................... 38

Search .......................................................... 38

Store ............................................................. 38

Install Menu in AV Modes .............................. 38

Colour System ........................................39

Store ............................................................. 39

Program Table ............................................... 39

Name ...................................................... 39

Move .......................................................39

Delete .....................................................39

APS (Auto Programming System) ..........39

Country ................................................ 39

Source Menu .................................................... 39

PC Mode Menu System........................................ 40

PC Position Menu ............................................. 40

Autoposition .................................................. 40

H (Horizontal) Position .................................. 40

V (Vertical) Position ...................................... 40

Phase ............................................................ 40

Dot Clock ...................................................... 40

PC Picture Menu ........................................... 40

Sound Menu ................................................. 41

Feature Menu ............................................... 41

Source Menu ................................................ 41

Displaying TV Information .................................... 41

Mute Function ....................................................... 41

PIP (Picture-in-Picture) Mode ............................... 41

Picture Mode Selection......................................... 41

Freezing Picture ................................................... 41

Zoom Modes......................................................... 41

Auto .................................................................. 41

16:9 ................................................................... 42

4:3 ..................................................................... 42

Panoramic......................................................... 42

14:9 ................................................................... 42

Cinema ............................................................. 42

Subtitle .............................................................. 42

Zoom................................................................. 42

Teletext ................................................................. 42

Tips ....................................................................... 43

Screen Care...................................................... 43

Image Persistence ............................................ 43

No Power .......................................................... 43

Poor Picture ...................................................... 43

No Picture ......................................................... 43

Sound ............................................................... 43

Remote Control................................................. 43

Input Sources.................................................... 43

Appendix A: PC Input Typical Display Modes ....... 44

Appendix B: Supported DVI Resolutions .............. 45

Appendix C: AV and HDMI Signal Compatibility

(Input Signal Types) .............................................. 46

Appendix D: Pin Speciﬁ cations............................. 47

SCART connector pin speciﬁ cations ................ 47

HDMI connector pin speciﬁ cations ................... 47

Signal Input ....................................................... 47

PC RGB Terminal (D-sub 15-pin connector) . 47

S-input connector pin speciﬁ cations ................. 47

Appendix E: PIP/PAP Mode Combinations .......... 48

Speciﬁ cations ....................................................... 50

DVB-T functionality information ............................ 51

Environmental Information ................................... 51

Product Guarantee ............................................... 52

English - 3 -

Features

• Remote controlled colour LCD TV.

• Fully integrated digital TV (DVB-T).

• HDMI connectors for digital video and audio.

This connection is also designed to accept

high deﬁ nition signals.

• USB input.

• 200 programmes from VHF, UHF(analogue).

• 300 programmes for digital mode (IDTV).

• OSD menu system.

• Two scart sockets for external devices (such

as video, video games, audio set, etc.).

• Stereo sound system. (German+Nicam)

• Teletext, fastext, TOP text.

• Headphone connection.

• Automatic programming system.

• Forward or backward manual tuning.

• Sleep timer.

• Child lock.

• Automatic sound mute when no

transmission.

• NTSC playback.

• PIP / PAP / PAT functions.

• AVL (Automatic Volume Limiting).

• When no valid signal is detected, after 5

minutes the TV switches itself automatically

to standby mode.

• PLL (Frequency Search).

• PC input.

• Plug&Play for Windows 98, ME, 2000, XP,

Vista, Windows 7.

• Audio line out.

• Game Mode

• Active antenna power.

Accessories

SCREEN

LANG

SUBTITLE

PIP

RETURN

SOURCE

FAV

PRESETS

SLEEP

INFO

EPG

V+

V-

P-

P+

7 8

RC 3900

Remote Controller

Batteries

2 X AAA

Instruction Book

Quick Guide

Cable Holder

English - 4 -

Introduction

Thank you for choosing this product. This

manual will guide you for the proper

operation of your TV. Before operating

the TV, please read this manual

thoroughly.

Please do keep this manual in a safe

place for future references.

Preparation

For ventilation, leave a free space of at least

10 cm all around the set. To prevent any fault

and unsafe situations, please do not place any

objects on top of the set.

Use this device in moderate climates.

10 cm

Safety Precautions

Please read the following recommended

safety precautions carefully for your

safety.

SOME DOS AND DON’TS ON THE SAFE USE

OF EQUIPMENT

This equipment has been designed and

manufactured to meet international safety

standards but, like any electrical equipment,

care must be taken if you are to obtain the best

results and safety is to be assured.

**************

DO read the operating instructions before you

attempt to use the equipment.

DO ensure that all electrical connections

(including the mains plug, extension leads

and inter-connections between the pieces of

equipment) are properly made and in accordance

with the manufacturer’s instructions. Switch off

and withdraw the mains plug before making or

changing connections.

DO consult your dealer if you are ever in doubt

about the installation, operation or safety of

your equipment.

DO be careful with glass panels or doors on

equipment.

DO route the mains lead so that it is not likely

to be walked on, crushed, chafed, or subjected

to excessive wear and tear or heat.

**************

DON’T remove any ﬁ xed cover as this may

expose dangerous voltages.

DON’T obstruct the ventilation openings of the

equipment with items such as newspapers,

tablecloths, curtains, etc. Overheating will cause

damage and shorten the life of the equipment.

DON’T allow electrical equipment to be

exposed to dripping or splashing, or objects

ﬁ lled with liquids, such as vases, to be placed

on the equipment.

DON’T place hot objects or naked flame

sources such as lighted candles or nightlights

on, or close to equipment. High temperatures

can melt plastic and lead to ﬁ res.

DON’T use makeshift stands and NEVER ﬁ x

legs with wood screws - to ensure

complete safety always ﬁ t the manufacturer’s

approved stand or legs with the ﬁ xings

provided according to the instructions.

DON’T use equipment such as personal stereos

or radios so that you are distracted from

the requirements of trafﬁ c safety. It is illegal to

watch television whilst driving.

DON’T listen to headphones at high volume, as

such use can permanently damage your

hearing.

DON’T leave equipment switched on when it is

unattended unless it is speciﬁ cally stated

that it is designed for unattended operation or

has a stand-by mode. Switch off using the

switch on the equipment and make sure that

your family know how to do this. Special

arrangements may need to be made for inﬁ rm

or handicapped people.

DON’T continue to operate the equipment if you

are in any doubt about it working

normally, or if it is damaged in any way - switch

off, withdraw the mains plug and consult

your dealer.

English - 5 -

ABOVE ALL

--- NEVER let anyone especially children

push anything into holes, slots or any other

opening in the case - this could result in a

fatal electrical shock;

--- NEVER guess or take chances with

electrical equipment of any kind

--- it is better to be safe than sorry!

*************

Power Source

The TV set should be operated only from a 220-

240 V AC, 50 Hz outlet.

Power Cord

Do not place the set, a piece of furniture, etc.

on the power cord (mains lead) or pinch the

cord. Handle the power cord by the plug. Do

not unplug the appliance by pulling from the

power cord and never touch the power cord with

wet hands as this could cause a short circuit or

electric shock. Never make a knot in the cord or

tie it with other cords. The power cords should

be placed in such a way that they are not likely

to be stepped on. A damaged power cord can

cause ﬁ re or give you an electric shock. When it

is damaged and needs to be replaced, it should

be done by qualiﬁ ed personnel.

This TV receiver is supplied with a moulded

mains plug. The mains plug must not be cut off,

as it may contain a special radio interference

ﬁ lter, the removal of which could lead to impaired

performance. If you wish to extend the lead,

obtain an appropriate safety approved extension

lead or consult your dealer.

Observe the manufacturers instructions when

connecting extension leads to the set. Check

the fuse rating on the new plug; this should be

ﬁ tted with a 5 Amp fuse which conforms to either

ASTA or BSI (BS1362) approvals, these are

easily identifiable by either the

ASA

symbols. If you are in any doubt about the

installation of an extension lead, please consult

a competent electrician.

Warning

Do not leave your TV in standby or operating

mode when you leave your house.

Disconnecting the Device

The mains plug is used to disconnect TV set

from the mains and therefore it must remain

readily operable.

Moisture and Water

Do not use this device in

a humid and damp place

(avoid the bathroom, the

sink in the kitchen, and near

the washing machine). Do

not expose this device to

rain or water, as this may be

dangerous and do not place

objects filled with liquids,

such as vases, on top. Avoid

dripping or splashing.

If any solid object or liquid falls into the cabinet,

unplug the TV and have it checked by qualiﬁ ed

personnel before operating it any further.

Cleaning

Before cleaning, unplug the

TV set from the wall outlet.

Do not use liquid or aerosol

cleaners. Use soft and dry

cloth.

Ventilation

The slots and openings on the

TV set are intended for ventilation and to ensure

reliable operation. To prevent overheating, these

openings must not be blocked or covered in

anyway.

Heat and Flames

The set should not be placed

near to open flames and

sources of intense heat such

as an electric heater. Ensure

that no open ﬂ ame sources,

such as lighted candles,

are placed on top of the TV.

Batteries should not be exposed to excessive

heat such as sunshine, ﬁ re or the like.

Lightning

In case of storm and lightning

or when going on holiday,

disconnect the power cord

from the wall outlet.

English - 6 -

Replacement Parts

When replacement parts are required, make

sure that the service technician has used

replacement parts, which are speciﬁ ed by the

manufacturer or have the same speciﬁ cations as

the original one. Unauthorized substitutions may

result in ﬁ re, electrical shock or other hazards.

Servicing

Please refer all servicing to

qualiﬁ ed personnel. Do not

remove the cover yourself as

this may result in an electric

shock.

Waste Disposal

Instructions for waste disposal:

• Packaging and packaging aids are recyclable

and should principally be recycled. Packaging

materials, such as foil bag, must be kept away

from children.

• Batteries, including those which are heavy

metal-free, should not be disposed of with

household waste. Please dispose of used

battery in an enviromentally friendly manner.

Find out about the legal regulations which

apply in your area.

• Cold cathode fluorescent lamp in LCD

PANEL contains a small amount of mercury;

please follow the local laws or regulations for

disposal.

Information for Users in European

Union Countries

The mark is in compliance

with the Waste Electrical

and Electronic Equipment

Directive 2002/96/EC

(WEEE).

The mark indicates the

requirement NOT to dispose

the equipment including any

spent or discarded batteries

as unsorted municipal waste, but use the return

and collection systems available. If the batteries

or accumulators included with this equipment,

display the chemical symbol Hg, Cd, or Pb,

then it means that the battery has a heavy

metal content of more than 0.0005% Mercury,

or more than 0.002% Cadmium or more than,

0.004% Lead.

Headphone Volume

Excessive sound pressure from

earphones and headphones

can cause hearing loss.

Installation

To prevent injury, this device

must be securely attached to the wall in

accordance with the installation instructions

when mounted to the wall (if the option is

available).

LCD Screen

The LCD panel is a very high technology product

with about a million thin ﬁ lm transistors, giving

you ﬁ ne picture details. Occasionally, a few

non-active pixels may appear on the screen

as a ﬁ xed blue, green or red point. Please note

that this does not affect the performance of

your product.

English - 7 -

Overview of the Remote Control

SCREEN

LANG

SUBTITLE

PIP

RETURN

SOURCE

FAV

PRESETS

SLEEP

INFO

EPG

V+

V-

P-

P+

7 8

RC 3900

Standby1.

Mono/Stereo - Dual I-II / Currrent2.

Language (*) (in DTV mode)

Expand (in TXT mode)/ Image size3.

Green / Picture Menu / Subtitle on-off (*) 4.

(in DTV mode)

Red /Sound Menu / Channel List (*) (in 5.

DTV mode)

Numeric buttons6.

Teletext / Mix / PAT Mode (in TXT mode) 7.

Cursor Left8.

Menu9.

AV / Source10.

Favourite Mode Selection (*) (in DTV 11.

mode)

Volume Up12.

Info / Reveal (in TXT mode)13.

Mute14.

Volume Down15.

Programme Down / Page up (in DTV 16.

mode)

Electronic programme guide (in DTV 17.

mode)

Programme Up / Page down (in DTV 18.

mode)

Sleep Timer19.

Picture Mode Selecion20.

Okay (Store) / Select / Hold (in TXT mode)21.

Cursor Down22.

Exit (in DTV mode) / Return / Index page 23.

(in TXT mode)

Cursor Right / Subpage (in TXT mode)24.

Cursor Up25.

Previous programme26.

Yellow / Feature Menu / Currrent 27.

Language (*) (in DTV mode)

Blue / Install Menu / Favourite Mode 28.

Selection (*) (in DTV mode)

No function29.

Subtitle on-off (in DTV mode) / TXT 30.

subtitle

(*)

For EU countries except UK.

English - 8 -

LCD TV and Operating Buttons

FRONT VIEW

REAR VIEW

Standby button1.

TV/AV button2.

Programme Up/3.

Down buttons

Volume Up/Down 4.

buttons

Note: Press “ ”/

“ ”buttons at the

same time to view main

menu.

English - 9 -

Viewing the Connections- Back Connectors

12 13

1. S/PDIF Digital Out outputs digital audio signals of the currently watched source.

Use a digital optic cable to transfer audio signals to a device that has S/PDIF input.

2. Subwoofer Out is for connecting an external, active subwoofer to the set to give a much

deeper bass effect.

Use an appropriate RCA cable to connect the set to a subwoofer unit.

Audio Line Outs 3. output audio signals to an external device such as an optional sound

system.

To connect the external speakers to your TV, use AUDIO LINE OUTS of the TV with an

audio cable.

4. SCART 2 inputs or outputs for external devices.

5. SCART 1 inputs or outputs for external devices.

Connect the SCART cable between SCART sockets on TV and SCART socket on your

external device (such as a decoder, a VCR or a DVD player).

Note: If an external device is connected via the SCART sockets, the TV will automatically switch to

AV mode. If both sockets are employed at the same time, SCART 1 will override SCART 2 unless

manually selected.

Note: You should connect the decoder to EXT-1, if you are planning to watch a scrambled channel.

The decoder might not function properly if you do not connect the decoder to the Scart 1 (Ext-1) socket.

Note: Picture state can be affected by scart cable quality.

6. Component Video Inputs (YPbPr) are used for connecting component video.

You can connect the component video and audio sockets with a device that has component

output. Connect the component video cables between the COMPONENT VIDEO INPUTS

on on the TV and the component video outputs of your device. While connecting, be sure

English - 10 -

that the letters on your TV, “ Y”, “ Pb”, “ Pr” correspond with your device’s connectors.

7. PC/YPbPr Audio Inputs are used for connecting audio signals of a PC or a device that

connects to the TV via YPbPr.

Connect the PC audio cable between the AUDIO INPUTS on the TV and audio output of

your PC to enable PC audio.

Connect the audio cable between AUDIO INPUTS on the TV and audio outputs of your

device to enable component audio.

8. S/PDIF Coaxial Out outputs digital audio signals of the currently watched source.

Use an SPDIF coaxial cable to trasfer audio signals to a device that has S/PDIF input.

9. RF Input connects to an antenna or a cable.

Note that if you use a decoder or a media recorder, you should connect the aerial cable

through the device to the television with an appropriate antenna cable, as shown in the

illustrationin the following pages.

10. PC Input is for connecting a personal computer to the TV set.

Connect the PC cable between the PC INPUT on the TV and the PC output on your PC.

11. HDMI 3: HDMI Input

HDMI 2: 12. HDMI Input

HDMI 1: 13. HDMI Input

HDMI Inputs are for connecting a device that has an HDMI socket. Your LCD Television is

capable of displaying High Deﬁ nition pictures from devices such as a High Deﬁ nition Satellite

Receiver or DVD Player. These devices must be connected via the HDMI sockets or Component

Socket. No sound connection is needed for an HDMI to HDMI connection.

English - 11 -

Viewing the Connections - Side Connectors

CI Slot is used for inserting a CI card. A CI card allows you 1.

to view all the channels that you subscribe to. For more

information, see “Conditional Access” section.

Side USB input .2.

Note: Codec update cannot be performed.

Side HDMI Input is for connecting a device that has an HDMI 3.

socket.

Headphone jack is used for connecting an external headphone 4.

to the system. Connect to the HEADPHONE jack to listen to

the TV from headphones.

Video Input is used for connecting video signals of external 5.

devices.Connect the video cable between the VIDEO IN

socket on the TV and the VIDEO OUT jack on your device.

Audio Inputs are used for connecting audio signals of external 6.

devices. Connect the audio cable between the AUDIO INPUTS

on the TV and the AUDIO OUTPUT jacks on your device.

Note: If you connect a device to the TV via the VIDEO INPUT,

you should also connect your device with an audio cable to the

AUDIO INPUTS of the TV to enable audio.

S-Video Input is used for connecting an S-Video signal (e.g. 7.

from a camcorder or VCR). For using S-VIDEO input; connect

the video cable between the S-VIDEO input on the TV and the S-Video output on your

device. Connect the audio cable between the AUDIO INPUTS (indicated with letter C in the

illustration) on the TV and the audio jacks on your device.

Standby switch is used for turning the TV on or off.8.

English - 12 -

Power Connection

IMPORTANT : The TV set is designed to operate on 220-240V AC, 50 Hz.

• After unpacking, allow the TV set to reach the ambient room temperature before you connect

the set to the mains.

• Plug the power cable to the mains socket outlet.

Aerial Connection

• Connect the aerial or cable TV plug to the AERIAL INPUT socket located at the rear of the TV.

Using the Cable Holder

You can use the supplied cable holder as the following:

• Place the cable holder into the cable holder hole located on the rear side of the TV as illustrated

above.

• Place cables into the cable holder after all necessary connections are made.

REAR VIEW

English - 13 -

Using Digital Multimedia Connectors

• You can connect USB devices to your TV by using the USB input of the TV. This feature allows

you to display/play JPG and MP3 ﬁ les stored in a USB stick.

• It is possible that certain types of USB devices (e.g. MP3 Players) may not be compatible with

this TV.

• You may back up your ﬁ les before making any connections to the TV set in order to avoid any

possible data loss. Note that manufacturer will not be responsible for any ﬁ le damage or data

loss.

• Do not pull out USB module while playing a ﬁ le.

CAUTION: Quickly plugging and unplugging USB devices, is a very hazardous operation.

Especially, do not repeatedly quickly plug and unplug the drive. This may cause physical

damage to the USB player and especially the USB device itself .

SIDE VIEW USB MEMORY

USB Memory Connection

• Plug your USB device to the USB input of the TV.

Note: USB hard disk drives are not supported.

• If the plugged USB disk is not recognised, please reinsert the disk.

• It is recommended that you connect your USB device directly to the USB input of the TV. Some

compatibility problems may occur if you use a separate cable connection.

Side HDMI Connection

You can use side HDMI input to connect a device that has an HDMI connector to your TV. Use

an appropriate HDMI cable to make such a connection. Note that you should switch to HDMI-

4 source to view the content from the connected device. Power off both the TV and the device

before making any connections.

• Side HDMI Input supports connections between HDMI devices such as DVD players. You can

use side HDMI input of the TV to connect to an external HDMI device. Use an HDMI cable to

connect.

HDMI DEVICE SIDE VIEW

English - 14 -

Connecting the LCD TV to a PC

For displaying your computer’s screen image on your LCD TV, you can connect your computer

to the TV set.

• Power off both computer and display before making any connections.

• Use 15-pin D-sub display cable to connect a PC to the LCD TV.

• When the connection is made, switch to PC source. See “Input selection” section.

• Set the resolution that suits your viewing requirements. Resolution information can be found in

the appendix parts.

REAR VIEW

PC audio cable

(not supplied)

to AUDIO INPUTS

on the TV

PC RGB cable

(not supplied)

to PC input

Audio

Inputs

PC Input

English - 15 -

Connecting to a DVD Player

If you want to connect a DVD player to your LCD TV, you can use connectors of the TV set. DVD

players may have different connectors. Please refer to your DVD player’s instruction book for

additional information. Power off both the TV and the device before making any connections.

Note: Cables shown in the illustration are not supplied.

• If your DVD player has an HDMI socket, you can connect via HDMI. When you connect to DVD

player as illustrated below, switch to HDMI source. See, “Input Selection” section.

• Most DVD players are connected through COMPONENT SOCKETS. Use a component video

cable to connect video input. For enabling audio, use a component audio cable as illustrated

below. When the connection is made, switch to YPbPr source. See, “Input selection” section.

• You may also connect through the SCART 1 or SCART 2. Use a SCART cable as shown

below.

Note: These three methods of connection perform the same function but in different levels of quality. It is not

necessary to connect by all three methods.

HDMI

inputs

Scart sockets

Component

video

inputs

Component

audio

inputs

DVD Player

REAR VIEW

Page is loading ...

Hitachi L46VN05U Instructions For Use Manual

Brand: Hitachi

Model: L46VN05U

Category: LCD TVs

Type: Instructions For Use Manual

Download PDF

report

Hitachi L46VN05U Instructions For Use Manual

Hitachi L46VN05U Instructions For Use Manual

Related papers

Other documents