Datalogic S.r.l. Lynx 00N0WI-1N1-MEN0 User manual

1 INTRODUCTION

1.1 LYNX DESCRIPTION

The Lynx contains the most innovative technical features, providing them to the user

in an ergonomic and elegant form factor. The accelerometer, the vibrator alert and

the 3 LEDs help to do not waste time in the configuration and usage of the product.

Working with the Lynx becomes an easy pleasure.

The great aesthetics does not put the rubustness on a second level.The Lynx has

been deisgned for surviving to industrial environmental, outside and inside the four

walls. The reliability of the product continues with the architecture chosen: an

806MHz processor working with 256 MB RAM and 512 MB of Flash. A Micro SD card

slot supporting SDHC storage cards provides for virtually unlimited storage space.

The Lynx has been equipped with both a 1D laser scanner and 2D bar code imager.

For being ready also to the most demanding applicatinons, an autofocus camera with

flash has been foreseen on the back of the product.

The Lynx provides four wireless technologies in the same form factor, without

antenna protruding: Bluetooth® v2.1 EDR for fast data transfer, 802.11b/g/n with

CCX v4, 802.11i Security, UMTS HSPA+ for real-time communication outside the

four walls and Assisted GPS (A-GPS) with Skyhook‘s Core Engine hybrid positioning

system for location based applications.

Them micro-USB port facilitates charging with a phone industry standard power

supply or On-the-Go (OTG) communications.

The Lynx integrates the latest Windows Embedded Hend Held 6.5, tailored for mobile

devices.

As all the Datalogic ADC Computers, also this PDA is offering Wavelink Avalanche®

for a fast configuration and deploymant.

Finally, Datalogic’s comprehensive service programs protect the Lynx investment.

1.2 AVAILABLE MODELS

The brand new Lynx is available in different models depending on the options it is

equipped with. All options are listed below:

 communication options: 802.11 b/g/n radio, Bluetooth®, GSM

 data capture options: laser, 2D imager

 compute options: Windows Mobile 6.5

 keyboard options: numeric, qwerty

For further details about the Lynx models refer to the web site:

www.adc.datalogic.com

.

For further information regarding Windows Embedded Handheld refer to the website:

http://www.microsoft.com/windowsembedded

.

The currently available models are:

 944400000 Lynx 00N0LD-1N0-MEN0

Lynx with Bluetooth v2.0, Wi-Fi 802.11 b/g/n, Decodified Laser (SE955),

Windows Mobile 6.5, 27-Key Numeric

 944400001 Lynx H2N0LD-1N1-MEN0

Lynx with Bluetooth v2.0, UMTS HSPA+ Voice and Data, Assisted GPS, Wi-Fi

802.11 b/g/n, Decodified Laser (SE955), Camera, Windows Mobile 6.5, 27-Key

Numeric

 944400002 Lynx 00N0WI-1N1-MEN0

Lynx with Bluetooth v2.0, Wi-Fi 802.11 b/g/n, 2D Imager (4500) Wide Aspect,

Camera, Windows Mobile 6.5, 27-Key Numeric

 944400003 Lynx H2N0WI-1N1-MEN0

Lynx with Bluetooth v2.0, UMTS HSPA+ Voice and Data, Assisted GPS, Wi-Fi

802.11 b/g/n, 2D Imager (4500) Wide Aspect, Camera, Windows Mobile 6.5, 27-

Key Numeric

 944400004 Lynx 00N0LD-1Q0-MEN0

Lynx with Bluetooth v2.0, Wi-Fi 802.11 b/g/n, Decodified Laser (SE955),

Windows Mobile 6.5, 46-Key QWERTY

 944400005 Lynx H2N0LD-1Q1-MEN0

Lynx with Bluetooth v2.0, UMTS HSPA+ Voice and Data, Assisted GPS, Wi-Fi

802.11 b/g/n, Decodified Laser (SE955), Camera, Windows Mobile 6.5, 46-Key

QWERTY

 944400006 Lynx 00N0WI-1Q1-MEN0

Lynx with Bluetooth v2.0, Wi-Fi 802.11 b/g/n, 2D Imager (4500) Wide Aspect,

Camera, Windows Mobile 6.5, 46-Key QWERTY

 944400007 Lynx H2N0WI-1Q1-MEN0

Lynx with Bluetooth v2.0, UMTS HSPA+ Voice and Data, Assisted GPS, Wi-Fi

802.11 b/g/n, 2D Imager (4500) Wide Aspect, Camera, Windows Mobile 6.5, 46-

Key QWERTY

1.3 PACKAGE CONTENTS

The Lynx package contains:

 1 Lynx PDA

 1 Lynx quick start guide

 1 rechargeable battery pack (standard for Wi-Fi models, high cap for UMTS

models)

 1 power supply with regional plugs

 1 Lanyard

 1 guitar pick stylus

Any other packages will contain the accessories necessary for the Lynx connection

to the host computer and to the network: the cradle, one or more connection cables.

Remove all the components from their packaging; check their integrity and congruity

with the packing documents.

Keep the original packaging for use when sending products to the

technical assistance center. Damage caused by improper

packaging is not covered under the warranty.

CAUTION

Rechargeable battery packs are not initially charged. Therefore the

first operation to perform is to charge them. See paragraph

오류

!

참조

원본을

찾을

수

없습니다

..

NOTE

1.4 INSERTING MICROSD CARD

Lynx supports microSD memory cards. To access the microSD card slot and insert

the card, proceed as follows:

1. Turn off the Lynx.

2. Shift the battery latch to the left and remove the battery pack:

3. Open the card slot and insert the microSD card with the written part downward:

4. Shift the card to the right to lock it into the cardholder; close the card slot:

5. First insert the bottom (contacts) and then the upper side of the battery pack into

the slot. Press until the battery latch clicks..

1.4.1 Removing the MicroSD Card

To remove the microSD card, follow the steps above to access the microSD card

cage under the battery, and remove it from microSD slot.

Follow proper ESD precautions to avoid damaging the

microprocessors in the Lynx or the microSD card itself.

Proper ESD precautions include, but are not limited to, working on

an ESD mat and ensuring that the operator is properly grounded.

Do not force the card. If you feel resistance, remove the card, check

the orientation, and reinsert it.

Do not use the microSD card slot for any other accessories.

It is highly recommended that users latch the card cage's bale even

when the card is not present.

CAUTION

1.5 INSTALLING THE SIM CARD

To correctly insert the SIM Card, proceed as follows:

1. Turn off the Lynx.

2. Shift the battery latch to the left and remove the battery pack:

3. Insert the SIM card with the contacts downwards:

4. First insert the bottom (contacts) and then the upper side of the battery pack into

the slot. Press until the battery latch clicks.

Follow proper ESD precautions to avoid damaging the SIM card.

Proper ESD precautions include, but are not limited to, working on

an ESD mat and ensuring that the operator is properly grounded.

Do not force the card. If you feel resistance, remove the card, check

the orientation, and reinsert it.

Do not use the SIM card slot for any other accessories.

CAUTION

1.5.1 Removing the SIM Card

To remove the SIM card, follow the steps above to access the SIM area, and remove

it from its slot.

All the basic functionalities normally associated to the SIM card are

managed by the terminal (GPRS connectivity, phone calls, SMS

handling).

All core functionalities (GPRS connectivity, phone calls, and SMS

handling) is managed by the terminal. Advanced functionality may

require additional software from the SIM card vendor.

It is possible that not all the services connected to the SIM card can

be used or can be managed by the terminal.

NOTE

1.6 ACCESSORIES

 Cradles

94A150036 Dock, Single Slot, Lynx

94A150037 Charger, 4 Slot Dock, Lynx

94A150038 Dock, Ethernet 4 Slot, Lynx

94A150039 Charger, 4 Slot Battery, Lynx

 Batteries

94ACC0064 Battery, Standard Capacity, Lynx

94ACC0065 Battery, High Capacity, Lynx

 Power Supply

94A051975 Power Adapter, 12 to 24v Pwr Plug 2.1mm

94A051976 Adapter, Pwr Jack 2.1mm To Handylink

94ACC1380 Power Supply, Micro USB

94ACC1381 Power Supply, Dock, PWR Plug 2.1mm

 Cables

94A051020 Cable for dock-PC (RS232) communication

94A051968 Cable, Micro USB, Client

94A051969 Cable, Micro USB, Host

94A051970 Cable, USB Handylink, Client

94A051971 Cable, USB Handylink, Host

94A051972 Cable, RS232 Handylink, Client

94A051973 Cable, RS232 Handylink, Host

94A051974 Cable, Dex Handylink

 Various

95ACC1033 Screen Protector Kit, 5 Pack

94ACC1230 Swivel for Functional Case (10pcs)

94ACC1345 Stylus Pen (10 pcs.)

94ACC1371 Module, Ethernet, Single Slot Dock

94ACC1372 Module, Modem, Single Slot Dock

94ACC1382 Stylus, Guitar Pick W/ Cord (5pcs)

Use only a Datalogic ADC-approved power supply and cables. Use

of an alternative power supply will invalidate any approval given to

this device and may be dangerous.

NOTE

2. BATTERIES AND MAINTENANCE

Rechargeable backup batteries and battery packs are not initially

charged. Therefore the initial operation to perform is to charge them.

See below.

NOTE

By default, the battery pack is disconnected at the factory to avoid

damage due to excessive draining.

Annual replacement of rechargeable battery pack avoids possible

risks or abnormalities and ensures maximum performance.

CAUTION

1.1 CHARGING THE BATTERY PACK

The battery pack autonomy varies according to many factors, such

as the frequency of barcode scanning, RF usage, battery life,

storage, environmental conditions, etc.

NOTE

The battery icon on the Taskbar indicates when the battery pack is low.

It is possible to recharge the battery pack by connecting the power supply directly to

the Lynx.

Alternatively, it is also possible to recharge the battery pack by using the single slot

dock, the powered mobile dock, the Ethernet four slot dock or the four slot battery

charger.

Moreover recharging is possible by USB Direct connection with the host computer,

but with longer charging times and only if the PDA is off.

During the charging process the LED positioned at the left side of the display is red

constant. Once the charging process has been completed this LED is green constant

(see par. 오류! 참조 원본을 찾을 수 없습니다.).

If the battery pack is removed from the PDA, it can be recharged by inserting it into

the rear slot of the single slot dock, the powered mobile dock, the Ethernet four slot

dock or the four slot battery charger.

It’s recommended to charge batteries before first use.

NOTE

Risk of explosion if battery is replaced by an incorrective type.

Dispose of used batteries according to the instructions.

CAUTION

Il y a risque d’explosion si la batterie est remplacée par une batterie

de type incorrect.

Mettre au rebut les batteris usagées conformément aux instructions.

CAUTION

Avoid storing batteries for long periods in a state of full charge or very

low charge.

We recommend charging the battery pack every two to three months

to keep its charge at a moderate level to maximize battery life.

CAUTION

Even if the storage temperature range is wider, In order to achieve

the longest battery life, store the terminal and the spare batteries

between 20 to 30 ºC (68 to 86 ºF).

Extended batteries must be charged at a temperature ranging from

0° to +45°C (+32° to +113°F).

Standard batteries must be charged at a temperature ranging from 0°

to +45°C (+32° to +113°F).

NOTE

The battery level may display incorrectly for several minutes after the

Lynx is disconnected from its charger if the charging cycle is not

completed.

NOTE

The Lynx could get warm during charging, this is normal and does

not mean a malfunction.

NOTE

Use only a USB-IF compliant USB port as a charging source.

NOTE

1.2 REPLACING THE BATTERY PACK

To correctly replace the battery pack, proceed as follows.

1. Turn off the Lynx.

2. Shift the battery latch to the left and remove the battery pack:

3. Install the new battery pack, first insert the bottom (contacts) and then the upper

side of the battery pack into the slot. Press

until the battery latch clicks.

WARNING

Installing, charging and/or any other action should be done by

authorized personnel and following this manual.

The battery pack may get hot, explode, ignite, and/or cause serious

injury if exposed to abusive conditions.

If the battery pack is replaced with an improper type, there is risk of

explosion.

Do not place the battery pack in or near a fire or heat; do not place

the battery pack in direct sunlight, or use or store the battery pack

inside unventilated areas in hot weather; do not place the battery

pack in microwave ovens, dryer, high pressure containers, on

induction cookware or similar device. Doing so may cause the

battery pack to generate heat, explode or ignite. Using the battery

pack in this manner may also result in a loss of performance and a

shortened life expectancy.

Use only a Datalogic ADC approved power supply. The use of an

alternative power supply will void the product warranty, may cause

product damage and may cause heat, explode or ignite.

The area in which the units are charged should be clear of debris

and combustible materials or chemicals.

Do not use the battery pack of this terminal for power devices

different from this PDA.

Immediately discontinue use of the battery pack if, while using,

charging or storing the battery pack, the battery pack emits an

unusual smell, feels hot, changes colour or shape, or appears

abnormal in any other way.

Do not short-circuit the battery pack contacts connecting the positive

terminal and negative terminal. This might happen, for example,

when you carry a spare battery pack in your pocket or purse;

accidental short–circuiting can occur when a metallic object such as

a coin, clip, or pen causes direct connection of the contacts of the

battery pack (these look like metal strips on the battery pack). Short–

circuiting the terminals may damage the battery pack or the

connecting object.

Do not apply voltages to the battery pack contacts.

Do not pierce the battery pack with nails, strike it with a hammer,

step on it or otherwise subject it to strong impacts or shocks.

WARNING

Do not disassemble or modify (i.e. bend, crush or deform) the battery

pack. The battery pack contains safety and protection devices,

which, if damaged, may cause the battery pack to generate heat,

explode or ignite.

In case of leakage of liquid from the battery, avoid contact with liquid

the skin or eyes. If the contact occurs, immediately wash the affected

area with water and consult a doctor.

Do not solder directly onto the battery pack.

Do not expose the battery pack to liquids.

Avoid any knocks or excessive vibrations. If the device or the battery

is dropped, especially on a hard surface, you should take it to the

nearest Authorised Repair Centre for inspection before continuing to

use it.

Do not replace the battery pack when the device is turned on.

Do not remove or damage the battery pack’s label.

Do not use the battery pack if it is damaged in any part.

Battery pack usage by children should be supervised.

Collect and recycle waste batteries separately from the device in

comply with European Directive 2006/66/EC, 2002/95/EC,

2002/96/EC and subsequent modifications, US and China regulatory

and others laws and regulations about environment.

In order to guarantee an adequate operating autonomy, when

replacing the battery pack the PDA checks the battery energy level.

If the battery is not sufficiently charged, Lynx does not turn on (when

pressing the ON/OFF key).

In this case, either substitute the battery pack with a charged one

(sufficiently charged) or insert Lynx into a powered cradle or plug it

into the direct power supply.

NOTE

To maximize battery life, turn off radios when they are not needed.

NOTE

1.3 CLEANING THE PDA

Periodically clean the Lynx with a slightly dampened cloth.

Do not use alcohol, corrosive products or solvents.

3. CONNECTIONS

1.1 USB CONNECTION

You can use the standard micro USB cable 94A051968 or the Datalogic Handylink

cable 94A051970 to directly connect the Lynx to a host computer to transfer data

through the USB interface.

Key:

A Host computer C Lynx

B Standard Micro USB cable

94A051968/ 94A051970 Handylink

USB Client Cable

Connection through the cable complies to the 1.1 USB standard.

NOTE

A

B

C

Page is loading ...

Datalogic S.r.l. Lynx 00N0WI-1N1-MEN0, Lynx 00N0LD-1N0-MEN0, Lynx 00N0LD-1Q0-MEN0, Lynx 00N0WI-1Q1-MEN0, Lynx H2N0LD-1N1-MEN0, Lynx H2N0LD-1Q1-MEN0, Lynx H2N0WI-1N1-MEN0, Lynx H2N0WI-1Q1-MEN0, U4G0070, U4G0073 User manual

Related papers

Other documents