BLACK+DECKER SNC3650L252 User manual

Page is loading ...

5

ENGLISH

(Original instructions)

4

5

Intended use

Your BLACK+DECKER SNC3650L252 Snow

thrower has been designed for Clearing snow

from areas. This appliance is intended for

consumer use only.

Safety instructions

Warning! When using cordless appliances, basic safety

precautions, including the following, should always be followed

to reduce the risk of re, electric shock, personal injury and

material damage.

Warning! When using the machine the safety rules must be

followed. For your own safety and bystanders please read

these instructions before operating the machine. Please keep

the instructions safe for later use.

u Read all of this manual carefully before operating the

appliance.

u The intended use is described in this manual. The use of

any accessory or attachment or the performance of any

operation with this appliance other than those

recommended in this instruction manual may present a

risk of personal injury.

u Be thoroughly familiar with the controls and the proper use

of the equipment.

u Know how to stop the unit and disengage the controls

quickly.

u Never allow children to operate the equipment. Never

allow adults to operate the equipment without

proper instruction.

u Keep the area of operation clear of all persons, particularly

small children, and pets.

u Exercise caution to avoid slipping or falling, especially

when operating in reverse.

u Retain this manual for future reference.

Using your appliance

Always take care when using the appliance.

u Thoroughly inspect the area where the equipment is to be

used and remove all doormats, sleds, boards, wires, and

other foreign objects.

u Disengage all clutches and shift into neutral before

starting the engine.

u Do not operate the equipment without wearing adequate

winter garments. Wear footwear, which will improve

footing on slippery surfaces.

u Use a grounded three-wire plug-in for all units with electric

drive motors or electric starting motors.

u Adjust the collector housing height to clear gravel or

crushed rock surface.

u Never attempt to make any adjustments while the engine

is running (except where specically recommended by

manufacturer).

u The operation of any powered machine can result in

foreign objects being thrown into the eyes.

u Always wear safety glasses or eye shields during

operation or while performing an adjustment or repair.

u This appliance is not intended for use by young or inrm

persons without supervision.

u The appliance is not to be used as a toy.

u Do not allow children or animals to come near the work

area or touch the appliance.

u Close supervision is necessary when the appliance is

used near children.

u Do not immerse the appliance in water.

u Do not open body casing. There are no user serviceable

parts inside.

u Do not operate the appliance in explosive atmospheres,

such as in the presence of ammable liquids, gases or

dust.

u Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at all times.

u Exercise extreme caution when operating on or crossing

gravel drives, walks, or roads. Stay alert for hidden

hazards or trafc.

u After striking a foreign object, stop the engine, remove the

batteries from the main body, thoroughly inspect the snow

thrower for any damage, and repair the damage before

restarting and operating the snow thrower.

u If the unit should start to vibrate abnormally, stop the

engine and check immediately for the cause. Vibration is

generally a warning of trouble.

u Remove the safety key whenever you leave the operating

position, before unclogging the collector/impeller

housing or discharge guide, and when making any repairs,

adjustments, or inspections.

u When cleaning, repairing, or inspecting, make certain the

collector/impeller and all moving parts have stopped.

u Do not clear snow across the face of slopes. Exercise

extreme caution when changing direction on slopes. Do

not attempt to clear steep slopes.

u Never operate the snow thrower without proper guards,

plates or other safety protective devices in place.

u Never operate the snow thrower near glass enclosures,

automobiles, windows, etc. without proper adjustment of

the snow discharge angle. Keep children and pets away.

u Do not overload the machine capacity by attempting to

clear snow at too fast a rate.

u Never operate the machine at high transport speeds on

slippery surfaces. Use care when reversing.

u Never direct discharge at bystanders or allow anyone in

front of the unit.

u Disengage power to the collector/impeller when snow

thrower is transported or not in use.

6

ENGLISH

(Original instructions)

u Use only attachments and accessories approved by the

manufacturer of snow thrower (such as wheels).

u Never operate the snow thrower without good visibility or

light. Always be sure of your footing, and keep a rm hold

on the handles. Walk; never run.

u Do not carry passengers.

u Never operate the snow thrower without good visibility or

light.

u Take all possible precautions when leaving the machine

unattended remove the safety key.

After use

u When not in use, the appliance should be stored in a dry,

well ventilated place out of the reach of children.

u Children should not have access to stored appliances.

u When the appliance is stored or transported in a vehicle it

should be placed in the boot or restrained to prevent

movement following sudden changes in speed or

direction.

Inspection and repairs

u Before use, check the appliance for damaged or defective

parts. Check for breakage of parts, damage to switches

and any other conditions that may affect its operation.

u Do not use the appliance if any part is damaged or

defective.

u Have any damaged or defective parts repaired or replaced

by an authorised repair agent.

u Never attempt to remove or replace any parts other than

those specied in this manual.

Additional safety instructions for Snow throwers

u Mow across the face of slopes, never up and down.

Exercise extreme caution when changing direction on

slopes.

u Watch for holes, ruts, bumps, rocks or other hidden

objects. Uneven terrain could cause a slip and fall

accident. Tall grass can hide obstacles.

u Do not operate on wet grass or excessively steep slopes.

Poor footing could cause a slip and fall accident.

u Do not operate near drop-offs, ditches, or embankments.

You could lose your footing or balance.

u Do not use hands to unclog chute.

u Stop motor before removing debris.

u Do not direct discharge at bystander

Safety of others

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

u Children must be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving

parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Warning symbols

The following warning symbols are found on the appliance

along with the date code:

Warning! Read, understand and follow all

instructions in the user manual(s) before

attempting to assemble and operate.

R

Warning! Do not expose the appliance to rain

or wet conditions. Keep dry.

Warning! Beware of sharp blades.

Always turn the machine OFF and remove the

safety key before conducting inspection,

cleaning and maintenance.

Warning! Beware of ying stones and other

foreign objects that could be thrown from the

appliance. Keep bystanders away from the

working area.

Wear hearing protection.

Wear eye protection.

Wear breathing protection.

Keep hands,feet and clothing away from the

rotating auger to avoid injury.

7

ENGLISH

(Original instructions)

Danger! Cutting/dismemberment hazard - keep

feet away from the rotating auger.

Danger! Cutting/dismemberment hazard - keep

hands away from the rotating auger. Do not use

hands to unclog rotor housing. Stop motor

before removing debris.

Keep bystanders and children a safe distance

(at least 10m) away from the work area.

Wear protective gloves and non-slip footwear

when using the machine and handling debris.

Do not use hands to unclog chute.

The rotating part will continuously run for

several seconds after you turn off the machine.

Indoor use only. Only use battery charger

indoors

Directive 2000/14/EC guaranteed sound power.

Additional safety instructions for batteries and

chargers

Batteries

 Never attempt to open for any reason.

 Do not expose the battery to water.

 Do not expose the battery to heat.

 Do not store in locations where the temperature may

exceed 40 °C.

 Charge only at ambient temperatures between 10 °C and

40 °C.

 Charge only using the charger provided with the

appliance/tool. Using the wrong charger could result in

an electric shock or overheating of the battery.

 When disposing of batteries, follow the instructions given

in the section "Protecting the environment".

 Do not damage/deform the battery pack either by puncture

 Do not charge damaged batteries.

 Under extreme conditions, battery leakage may occur.

When you notice liquid on the batteries carefully wipe the

liquid off using a cloth. Avoid skin contact.

 In case of skin or eye contact, follow the instructions

below.

Warning!

damage to property. In case of skin contact, immediately rinse

with water. If redness, pain or irritation occurs seek medical

attention. In case of eye contact, rinse immediately with clean

water and seek medical attention.

p

Do not attempt to charge damaged batteries.

Chargers

Always check that the mains voltage corresponds to the

voltage on the rating plate.

Warning! Never attempt to replace the charger unit with a

regular mains plug.

 Use your BLACK+DECKER charger only to charge the

battery in the appliance/tool with which it was supplied.

Other batteries could burst, causing personal injury and

damage.

 Never attempt to charge non-rechargeable batteries.

 If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

 Do not expose the charger to water.

 Do not open the charger.

 Do not probe the charger.

 The appliance/tool/battery must be placed in a well

ventilated area when charging.

$

The charger is intended for indoor use only.

Read the instruction manual before use.

Electrical safety

#

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate. Never attempt to replace the charger

unit with a regular mains plug.

 If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

8

ENGLISH

(Original instructions)

Charging the battery

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell

temperature warms up or cools down.

u Plug the charger into an appropriate outlet before inserting

the battery pack.

u Insert the battery pack into the charger.

The green LED will ash indicating that the battery is being

charged.

The completion of charge is indicated by the green LED

remaining on continuously. The pack is fully charged and

may be used at this time or left in the charger

Warning! Recharge discharged batteries as

soon as possible after use or battery life may

be greatly diminished.

Charger diagnostics

This charger is designed to detect certain problems that can

arise with the battery packs or the power source. Problems

are indicated by one LED ashing in different patterns.

Bad Battery

The charger can detect a weak or damaged battery. The red

LED ashes in the pattern indicated on the label. If you see

this bad battery blink pattern, do not continue to charge the

battery. Return it to a service centre or a collection site for

recycling

Hot/Cold Pack Delay

When the charger detects a battery that is excessively hot or

excessively cold, it automatically starts a Hot/Cold Pack

delay, suspending charging until the battery has normalised.

After this happens, the charger automatically switches to the

Pack Charging mode. This feature ensures maximum

battery life. The red LED ashes in the pattern indicated on

the label when the Hot/Cold pack delay is detected.

State of Charge Indicator

The battery is equipped with a state of charge indicator. This

can be used to display the current level of charge in the

battery while in the trimmer and during charging. It does not

indicate appliance functionality and is subject to variation

based on product components, temperature and end user

application.

Checking State of Charge during use

u Press the state of charge indicator (A1).

u The four LEDs (A2) will illuminate indicating the percent

of charge in the battery (Fig.A.)

u If LED light does not illuminate, charge battery.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Features

This appliance includes some or all of the following features.

1. Handle bar

2. ON/OFF switch bail handle

3. Safety key

4. Safety switch button

5. Chute rotation rod

6. Frame lock/release knob (x4)

7. Battery compartment cover

8. Wheels

9. Carrying handle (For transport only)

10. Discharge chute

11. Chute deector

12. Deector knob

13. Auger

14. Middle frame

15. Upper frame

16. Cleanout stick

9

ENGLISH

(Original instructions)

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Warning! Before assembly, make sure the bail handle (2) is

released and the safety key (3) is removed.

Handles

u To engage the handle bar, pull upwards on the upper

frame (15) as shown in Figure B.

u Secure the connection of the lower frame (17) to the

middle frame (14) by fastening the handle bolts (18) and

frame knobs (6) on each side as shown in Figures C & D.

u Secure the connection of the middle frame (14) to the

upper frame (15) by tightening the handle bolts and frame

knobs (6) on each side as shown in Figure E.

Discharge Chute

u Place the chute deector (11) onto the discharge chute

(10).

u Insert a chute gasket (19) in between the chute connection

and secure the assembly with a deector knob (12) and

bolt (20) on each side as shown in Figures F, G & H.

u Position the chute deector to the desired height of the

snow stream.

NOTE: Do not overtighten the deector knobs.

Chute rotation rod

u Insert chute rotation rod (5) through the slot in the eye

hook (21) located on the middle frame (14) as shown in

Figure I.

u Locate the chute rotation coupler (22) on the main

housing.

u Insert the chute rotation rod into the chute rotation coupler

(22) and secure the assembly with the supplied retaining

pin (23) as shown in Figure J.

Installing and removing the battery pack

Warning! Make certain the safety key is removed to prevent

actuation before removing or installing battery.

To install battery pack

u Lift up on the battery compartment cover (7) to expose the

battery compartment (24) as shown in Figure K.

u Slide the battery (25) into the battery compartment until it

is fully seated and an audible click is heard as shown in

Figure L. Make sure battery pack is fully seated and fully

latched into position.

u Close the battery compartment cover. Ensure the cover is

fully latched before starting snow thrower.

To remove battery pack

u Open the battery compartment cover (7) as described

above.

u Depress the battery release button located on the battery

pack and pull battery pack out of tool as shown in Figure

M.

Use

READ THIS INSTRUCTION MANUAL BEFORE OPERATING

YOUR SNOW THROWER. See “Functional Description” to

familiarize yourself with the location of various controls and

adjustments. Save this manual for future reference.

Warning! Let the appliance work at its own pace. Do not

overload.

u Open the battery compartment cover and slide the battery

into the battery compartment until it is fully seated and an

audible click is heard Figure L. Make sure battery pack is

fully seated and fully latched into position.

u Close the battery compartment cover. Ensure the cover is

fully latched before starting snow thrower.

u Insert safety key (3) into the key slot (26) located on the

switch housing until it is fully seated inside housing as

shown in Figure N. The snow thrower is now operational.

u This snow thrower is equipped with a special on-off switch

box. To operate the snow thrower, push the safety switch

button (4) on the switch box (27), then pull the ON/OFF

switch bail handle (2) to the handle bar as shown in Figure

O.

u To turn the snow thrower off, simply release the ON/OFF

switch bail handle (2).

Operating tips

Warning! Always inspect area where snow thrower is to be

used and remove all stones, sticks, wire, bones, and other

debris which might be thrown by the snow thrower.

Warning! Some parts of the snow thrower may freeze under

extreme temperature conditions. Do not attempt to operate the

snow thrower when parts are frozen. If a part freezes while the

snow thrower is in use, stop the snow thrower, remove the

battery, and inspect for frozen parts. Free all parts before

restarting or operating the snow thrower.

Warning! Exercise extreme caution when changing direction

on slopes. Always maintain good footing.

u Keep the area of operation free of foreign objects that can

become thrown by the auger blades. Some objects may

be hidden from view by snow cover. If the snow thrower

hits an obstruction or picks up a foreign object during use,

stop the snow thrower, remove the battery, remove the

obstruction, and inspect the unit for damage. Repair or

replace any damaged part before restarting and operating

the unit.

u Ensure children, pets, and bystanders are kept away from

the area of operation.

u When moving the snow thrower, use the wheels as the

pivot point. Slightly tilt the snow thrower on this pivot point

to move it forward or backward.

10

ENGLISH

(Original instructions)

u Start your clearing path in the centre of the operation area.

Throw snow in a back and forth motion, each time moving

the discharge chute away from the area you are clearing.

Ensure to overlap clearing paths.

u If possible, discharge snow in the same direction as the

wind, not against the wind. This prevents snow from being

blown onto the cleared areas.

u When working on stone, gravel, or unpaved surfaces,

avoid throwing loose material along with the snow by

pushing down on the handle to raise the scraper at the

base of the unit above the stone or gravel.

Motor overload

To prevent damage due to overload conditions, do not try to

remove too much snow at one time. Do not push the snow

thrower with excessive force. Slow down, allow the snow

thrower to work at its own pace.

Changing throw direction and throw height

Warning! Never direct the snow discharge chute towards the

operator, bystanders, vehicles, or nearby structures. The

discharged snow and foreign objects accidentally picked up

and thrown by the snow thrower can cause serious damage

and personal injury.

Always orient the discharge chute in the opposite direction

from where the operator, bystanders, surrounding vehicles, or

structures are located.

u The discharge chute has an operating range of 180

degrees. Direct the snow discharge by rotating the chute

with the chute rotation rod (5) as shown in Figure 16.

Warning! Release the bail handle (2), remove the safety key

(3) and remove the battery before making any adjustments,

inspecting, services, changing of accessories, cleaning the

snow thrower, and the like. Any operation should be performed

only after the revolving parts inside the snow thrower have

come to a full stop.

The chute deector (11) on the top of the discharge chute (10)

controls the height of the snow discharge stream. When the

deector is up, the snow will discharge higher.When the

deector is down, the snow will discharge lower.

u Loosen the deector knobs (12) to raise or lower the

deector to the desired height. Re-tighten the deector

knobs (12) to secure the deector.

NOTE: Do not overtighten the deector knobs.

Warning! Ensure that the chute deector fully locks onto the

discharge chute. Any gap between the discharge chute and

the chute deector could allow foreign objects picked up by

the snow thrower to be thrown in the direction of the operator

causing serious bodily injury.

u Do not position the chute deector too far downward as

this can cause a gap (28) to appear between the deector

and discharge chute as shown in Figure Q.

Clearing blockages

Warning! Release the bail handle (2), remove the safety key

(3) and remove the battery before making any adjustments,

inspecting, services, changing of accessories, cleaning the

snow thrower, and the like. Any operation should be performed

only after the revolving parts inside the snow thrower have

come to a full stop.

u Release the bail handle (2), remove the safety key (3) and

remove the battery.

u Inspect the discharge chute and auger housing for clogs

and jams.

u Use attached cleanout stick (16) to remove clogs and

jams.

Warning! DO NOT ATTEMPT TO CLEAR JAMS OR CLOGS

WITH YOUR HANDS. If a part freezes while the snow thrower

is in use, stop the snow thrower, remove the battery. Free all

parts before restarting or operating the snow thrower.

Accessories

Warning! The use of any accessory not recommended for use

with this tool could be hazardous.

Recommended accessories for use with your snow thrower

are available from your local Black+Decker dealer or

authorized service centre.

Maintenance

Your BLACK+DECKER cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool/appliance care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

11

ENGLISH

(Original instructions)

Troubleshooting

Problem Solution

Snow thrower doesn’t

run when bail handle

is activated.

Check to make sure safety key

has been installed and is fully

seated and that button on switch

housing is being completely

depressed before pulling bail

handle.

Release bail handle to turn snow

thrower off. Remove safety key

and battery pack, and check that

auger is free to turn.

Check that the battery cavity is

free of debris and is connected

properly.

Has battery been fully charged?

Unit stops while

moving snow.

Release bail handle to turn snow

thrower off. Remove safety key

and battery pack. Check that

auger is free to turn.

Check that the battery cavity is

free of debris and is connected

properly.

Has battery been fully charged?

Move charger and battery pack to

a surrounding air temperature of

above 40 degrees F (4,5°C) or

below 105 degrees F (+40,5°C).

Avoid overloading the Snow

thrower.

Slow down working pace

.

Troubleshooting

Snow thrower is

abnormally noisy and

vibrates.

Release bail handle to turn Snow

thrower off. Remove safety key

and battery pack. Check that

auger is free to turn and ensure it

has not been bent or damaged. If

damaged, return Snow thrower to

a BLACK+DECKER Authorized

service centre.

If there is no visible damage and

the snow thrower still vibrates:

Return the snow thrower to an

authorized Black+Decker

authorized service centre.

Battery charger LEDs

not on.

Check plug connection.

Replace charger.

Protecting the environment

Z

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your BLACK+DECKER product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

z

Separate collection of used products and

packaging allows materials to be recycled and

used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

BLACK+DECKER provides a facility for the collection and

recycling of BLACK+DECKER products once they have

reached the end of their working life. To take advantage of this

service please return your product to any authorised repair

agent who will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local BLACK+DECKER ofce at the

address indicated in this manual. Alternatively, a list of

authorised BLACK+DECKER repair agents and full details of

our after-sales service and contacts are available on the

Internet at: www.2helpU.com

12

ENGLISH

(Original instructions)

Batteries

Z

At the end of their useful life, discard batteries with

due care for our environment:

u Run the battery down completely, then remove it from the

tool.

u NiCd, NiMH and Li-Ion batteries are recyclable. Place the

battery(s) in a suitable packaging to ensure that the

terminals cannot be short-circuited. Take them to any

authorised repair agent or a local recycling station.

u Do not short-circuit the battery terminals.

u Do not dispose of the battery(s) in a re as this may result

in a risk of personal injury or an Explosion.

Technical data

SNC3650L252

Input Voltage

V

DC

36

No-Load Speed

min

-1

2500

Weight

kg

14.5

Battery BL2036

Voltage

V

dc

36

Capacity Ah 2.0

Type

Li-ion

Charger 90567393 -05 typ.1

Input Voltage

V

AC

230

Output Voltage

V

DC

36

Current mA 1.3A

Approx. charge

time

h

1.5

Hand/arm weighted vibration value according to EN 786:

= < 3.175 m/s

2

, uncertainty (K) = 1.5 m/s

2

.

L

PA

(sound pressure) 70.2 dB(A) uncertainty (K) = 2.5 dB(A)

EC declaration of conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

%

SNC3650L252 Snow Thrower

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60335-1:2012 +A11; 2014,

ISO/DIS 8437; 1989

EN 62233; 2008

2000/14/EC, ANNEX III of 2000/14/EC as amendment by

2005/88/EC,

TÜV Rheinland LGA Products GmbH;

Tillystraß 2 D-90431N

..

1r

nberg, Germany;

Notied Body ID No.:0197

Level of accoustic power according to 2000/14/EC

(Annex III, L ≤ 50 cm):

L

WA

(measured sound power) 85.18 dB(A)

uncertainty (K) = 2 dB(A)

L

WA

(guaranteed sound power) 89 dB(A)

uncertainty (K) = 2 dB(A)

These products also comply with directive 2004/108/EC and

2011/65/EU.

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

R. Laverick

Engineering Manager

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

28/07/2015

13

ENGLISH

(Original instructions)

Guarantee

Black & Decker is condent of the quality of its products and

offers an outstanding guarantee. This guarantee statement is

in addition to and in no way prejudices your statutory rights.

The guarantee is valid within the territories of the Member

States of the European Union and the European Free Trade

Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within

24 months from the date of purchase, Black & Decker

guarantees to replace defective parts, repair products

subjected to fair wear and tear or replace such products to

ensure minimum inconvenience to the customer unless:

u The product has been used for trade, professional or hire

purposes;

u The product has been subjected to misuse or neglect;

u The product has sustained damage through foreign

objects, substances or accidents;

u Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker ofce at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to register

your new BLACK+DECKER product and to be kept up to date

on new products and special offers. Further information on the

BLACK+DECKER brand and our range of products is

available at www.blackanddecker.co.uk

Page is loading ...

BLACK+DECKER SNC3650L252 User manual

BLACK+DECKER SNC3650L252 User manual

in other languages

Related papers

Other documents