NuTone SS-113WH User manual

Category
Loudspeakers
Type
User manual

This manual is also suitable for

INTRODUCTION
These indoor speakers are designed to be used in a home theater
system as rear and/or front speakers and make an excellent low
cost, great sounding system when used in conjunction with
Sensonic powered subwoofers such as SS4108 or MS4110P.
They can also be used as speakers for background music
reproduction.
INSTALLATION
The SS113WH/BL (Figure 1) cube speakers are designed to be
mounted on a wall, hung from the ceiling or just placed on a
tabletop. The speakers come with their own stand and two
different types of mounting. A plate (Figure 2) and a ceiling
bracket (Figure 3). The plate is for wall mounting while the bracket
is for ceiling mounting.
CONNECTING THE AMPLIFIER
Always observe polarity. Speaker wires (cables) always have
some type of identification mark, such as a red/white band on one
of the conductors. Connect this conductor with the identification
band to the RED or “+” terminal on the back of the stereo amplifier
or the A/V receiver. Connect the other end of this conductor band
to the RED or “+” terminal of the speaker. Insert one end of the
other conductor (without the identification mark) to the BLACK or
“-” terminal on the amplifier or the A/V receiver. Insert the other
end to the BLACK terminal of the speaker. Make sure there are
no frayed, cut or punctured wires.
TESTING THE SYSTEM
When all connections have been completed, play music through
an amplifier and a music source such as a CD player. Initially,
keep the volume control on the amplifier at very low setting. Keep
tone controls, if any, at mid position. Slowly increase the volume
from the amplifier. Sound should be heard from the left and right
speakers. If not, refer to the Troubleshooting Guide.
The speaker has two halves which can be rotated independently.
Rotate the two halves gently, as required, to direct sound at a
specific area.
Cube Speakers
Model: SS-113WH (White), SS-113BL (Black)
For indoor applications
Power Handling Capacity: 100 Watts RMS
Impedance: 8 Ohms nominal
Features:
Meets or exceeds Electronic Industry Association (EIA) standard RS-426-A for
power testing
Magnetically Shielded
Twin, wide range, 2.5" woofers
Frequency Response: 120-20,000 Hz (
+
3dB)
Sensitivity: @ 1 meter with 1 Watt input: 86 dB
Nominal Impedance: 8 Ohms
READ & SAVE THESE INSTRUCTIONS!
INSTALLATION INSTRUCTIONS
FIGURE 1
FIGURE 2 FIGURE 3
STAND
Wall
Mounting
Plate
Ceiling
Bracket
Ceiling
Wall
Product specifications subject to change without notice.
4820 Red Bank Road, Cincinnati, Ohio 45227
Printed in China, Rev., 02/2004, Part No. 62104
®
Five Year Limited Warranty
WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period
of five (5) years from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this five year period, NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES
FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident,
improper maintenance or repair (other than by NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above limitation may not apply to you.
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH
PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the address stated below or telephone 1/800-543-8687, (b) give the model
number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present
evidence of the original purchase date.
Date of Installation Builder or Installer
Model No. and Product Description
IF YOU NEED ASSISTANCE OR SERVICE:
For the location of your nearest NuTone Independent Authorized Service Center:
Residents of the contiguous United States Dial Free 1-800-543-8687
Please be prepared to provide:
Product model number Date and Proof of purchase The nature of the difficulty
Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599.
Residents of Canada should write to: Broan-NuTone Canada, 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9.
Rev. 03/2001
Symptom
1. No sound from either speaker.
2. Sound from only one speaker.
3. Low bass sound.
4. Amplifier shuts off as volume is
increased.
Possible Cause
1. Improper source selected at amplifier.
2. Mute button pressed.
3. Wrong speaker output selected A or B.
4. Amplifier shuts off because of short
circuit.
1. There is missing connection.
2. Balance control on amplifier turned all
the way to left or right.
1. Wrong polarity on one speaker.
1. Amplifier is overloaded.
Possible Remedy
1. Select proper source.
2. Defeat Mute button.
3. Select proper position on A/B switch.
4. Check all wires and remove the short.
Check proper operation of
Amplifier/Receiver.
1. Check all wires and make all
connections.
2. Set the control to mid position.
1. Check polarity & rewire, if necessary.
1. Short circuit in wire.
Check all wires & remove short.
2. Make sure that if you have connected
more than one speaker per channel on
the amplifier, the minimum impedance
requirement of amplifier is met. Most
amplifiers are designed to take only
one 8 Ohm speaker per channel.
TROUBLESHOOTING GUIDE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

NuTone SS-113WH User manual

Category
Loudspeakers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI