Panasonic CQVD7003N Operating instructions

Brand: Panasonic

Model: CQVD7003N

Type: Operating instructions

CQ-VD7003N

English

Safety Information

CAUTION:

• PLEASE FOLLOW THE LAWS AND REGULATIONS

OF YOUR STATE, PROVINCE OR COUNTRY FOR

INSTALLATION OF THE UNIT.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE

THIS APPLIANCE TO RAIN, SPLASHING, DRIP-

PING OR MOISTURE.

CQ-VD7003N

English

Upgrade Options

Safety Information................................................2

Upgrade Options ..................................................3

Contents................................................................3

Installation ............................................................4

Electrical Connections ......................................10

Contents

Display Unit

CQ-VD7003N

Expansion Module

(CY-EM100N, option)

Hands-Free Kit featuring

Bluetooth

technology

(CY-BT100N, option)

CD Changer

(CX-DP880N, option)

DVD Changer

(CX-DH801N, option)

Car Navigation System

(CN-DV2300N, option)

Rear Monitor

iPod

TV Tuner

(CY-TUP153N, option)

CQ-VD7003N

English

Installation

Preparation Dashboard Installation

¡Before installation, check the radio operation with

antenna and speakers.

¡Disconnect the cable from the negative (–) battery ter-

minal (see caution below).

¡The unit should be installed in a horizontal position

with the front end up at a convenient angle, but not

more than 30°.

Installation Opening

The unit can be installed in any dashboard having an

opening as shown below. The dashboard should be 4.5

mm – 6 mm thick in order to be able to support the unit.

Installation Precautions

This product should be installed by a professional

installer, if possible.

In case of difficulty, please consult your nearest author-

ized Panasonic Service Centre.

1. This system is to be used only in a 12 V DC battery

system (car) with negative ground.

2. Follow the electrical connections carefully (a page

10-19). Failure to do so may result in damage to the

unit.

3. Connect the power lead after all other connections are

made.

4. Be sure to connect the battery lead (yellow) to the pos-

itive terminal (+) of the battery or fuse block (BAT) ter-

minal.

5. Insulate all exposed wires to prevent short circuiting.

6. Secure all loose wires after installing the unit.

7. Please carefully read the operating and installation

instructions of the respective equipment before con-

necting it to this unit.

0 – 30°

182 mm

53 mm

Caution

¡Do not disconnect the battery terminals of a car with

trip or navigational computer since all user settings

stored in memory will be lost. Instead take extra

care with installing the unit to prevent shorts.

Caution

¡Please follow the laws and regulations of your

province or country for installation of the unit.

¡When bending the mounting tab of the mounting

collar with a screwdriver, be careful not to injure

your hands and fingers.

¡We strongly recommend you to wear gloves for

installation work to protect yourself from injuries.

CQ-VD7003N

English

❏ Transportation Bracket Removal

Be sure to remove the transportation brackets before use (installation).

Use round head screws (

5 mmø x 6 mm) for installation. (a page 8)

Be careful not to lose these screws.

Round Head Screw

mmø x 6 mm)

Round Head Screw

mmø x 6 mm)

Transportation

Bracket

Transportation

Bracket

❏ Installation Hardware

(For Installation)

Qty.DiagramItemNo.

Trim Plate

(YFC054C087CA)

Mounting Collar

(YFX214C433CA)

Mounting Spring

(YFX054C077CA)

(ZZBISVD7001B)

Round Head Screw

(5 mmø x 6 mm)

Flat-Head Screw

(5 mmø x 6 mm)

Round Head Screw

(4 mmø x 3 mm)

(YEJVO1060)

Mounting Bolt (5 mmø)

(ZZBISVD7001E)

Spacer

Double-Faced Adhesive Tape

set

Note:

¡The number in parenthesis underneath each accessory

part name is the part number for maintenance and serv-

ice.

¡Accessories and their parts numbers are subject to

modification without prior notice due to improvements.

¡Use the supplied screws for installation exclusively. In

case of losing any of them, please order the specific

screw.

❏ Installation Hardware

(For

Wiring)

Qty.DiagramItemNo.

Reverse Extension Cord

(YEAJ012897)

ISO Antenna Adapter

(YEAA33144)

(YAJ024C118ZA)

Power Connector

Clip Connector

CQ-VD7003N

English

Installation (continued)

❏ Installation Procedures (When using Mounting Collar w)

Mounting the Display Unit

Insert the Mounting Collar w into the dashboard, and

bend the mounting tabs out with a screwdriver.

Establish the rear connection of the unit.

After fixing Power Connector

!0, fix the rear of the unit to

the car body by either method (a) or (b) shown at right.

Insert Trim Plate q.

After installation

reconnect the negative

(–) battery terminal.

Attach the Mounting Springs e to the unit.

Power Connector

r Mounting Bolt

(5 mmø)

e Mounting Spring

y Flat-Head Screw

(5 mmø x 6 mm)

Note:

¡The car model, installation condi-

tions and combination of the units

used may impose some restric-

tions on opening and closing the

monitor as well as on the angle

and position to which the monitor

can be adjusted.

Fastening the Mounting Collar

How much to bend the tabs will vary depending on the

car. Bend them with a screwdriver to fasten the

Mounting Collar

securely in the dashboard.

w Mounting Collar

Dashboard

Tab

Insert the unit into Mounting Collar w.

Secure the clamp plate of Mounting Collar

w to the hook of Mounting Spring e.

Clamp plate

IMPORTANT

When this unit is installed in dash-

board, ensure that there is sufficient

air flow around the unit to prevent

damage from overheating. Do not

block any ventilation holes on the

unit.

CQ-VD7003N

English

Two holes of the mounting spring allow you to select between two mounting types as shown below.

A few millimeters of

console projecting

Less projecting

Method for Fixing the Rear of the Unit

Method for Fixing the Mounting Spring

(A) Regular installation method (B) Deeper installation method

y Flat-Head Screw

(a) Using the Rear Support Strap (option) (b) Using the Rubber Cushion (option)

Fire wall of car

3 mmø

Tapping Screw

(option)

Rear Support Strap

(option)

Mounting Bolt

(5 mmø)

Mounting Bolt

(5 mmø)

Rear Support Bracket

(Provided on the Car)

Rubber Bushing

(option)

Hex. Nut

(option)

Caution

¡Method (B) is not available in some types of cars.

CQ-VD7003N

English

Installation (continued)

i Spacer

o Double-Faced Adhesive Tape

t Round Head Screw

(5 mmø x 6 mm)

Bracket

Mounting Hole

of a Bracket

(in section)

Existing Bracket (L) (Bracket originally attached to the car)

o Double-Faced

Adhesive Tape

Existing Bracket (R)

t Round Head Screw

(5 mmø x 6 mm)

i Spacer

❏ Installation Procedures (When not using Mounting Collar w)

Use the brackets supplied with your car when mounting this unit. The bracket shape and mounting method vary with car

manufacturers, car types and manufacturing year. Please consult your nearest dealer or installer.

Select mounting screws according to the hole positions and hole shape of the bracket.

y Flat-Head Screw (5 mmø x 6 mm) 4 pieces

u Round Head Screw (4 mmø x 3 mm)

4 pieces

t Round Head Screw (5 mmø x 6 mm) 2 pieces

Recycle the Round Head Screws that fixed the transportation brackets for two more

positions.

When using these

mounting holes

q Push the right and left clamp plates outward, one at a time, and pull the unit toward yourself.

w After removing the right and left clamp plates, pull the unit with both hands till it comes out.

Push here to

remove the

clamp plates.

To Remove the Unit

Use the supplied Spacer i if mounting hole of your

car is shaped like below.

CQ-VD7003N

English

—

SIDE BRAKE

The side brake (parking brake) switch position varies with car model.

For details on the exact location of the side brake (parking brake) switch

in your car, contact your dealer.

Attach a Clip Connector !1 to the end of the side

brake (parking brake) connection lead.

w The Clip Connector !1 is connected to the power

source side lead of the side brake (parking brake)

lever.

Connecting the Side Brake (Parking Brake) Connection Lead

Hand brake Foot brake

Side Brake (Parking Brake) Connection

Lead (Bright green)

When the side brake (parking brake) lever is

engaged, the unit is grounded by the chassis.

Side brake (parking brake) switch

Car chassis

Battery

Brake light

!1 Clip Connector

Side Brake (Parking Brake) Connection Lead

(Bright green)

Comes up to this point.

Power source side lead

Caution

¡For safety, be sure to ask your nearest professional installer to do this connection.

CQ-VD7003N

English

Electrical Connections

Precautions (ISO Connector)

¡The pin arrangement of the power connector conforms

to ISO standard.

¡The pin arrangement of ISO connectors in some cars

may differ from the ISO standard.

¡Please check that the pin arrangement of the connec-

tor in your car conforms to ISO standard.

¡For car types A and B, change the wiring of the red

and yellow leads as shown at below.

¡After connection, insulate the portions marked (C)

with insulating tape.

Note:

¡For cars other than types A and B, please consult your

local car shop.

BATTERY 15A

ACC

BATTERY 15A

ACC

ISO

Standard ISO

Car Type A

Car Type B

BATTERY 15A

ACC

A7: IGN or ACC 12 V supply

(Red)

(Yellow)

(Red)

(Yellow)

(Red)

(Yellow)

(Red)

(Yellow)

A4: IGN or ACC 12 V supply

A4: 12 V Batteries (Continuous supply)

A7: 12 V Batteries (Continuous supply)

A4: No connection

Note:

¡To prevent from damage to the unit, be sure to follow

the wiring diagrams at right.

¡Be sure to fully plug in the connectors. Secure them

with clamps and tapes.

¡All other installation methods require the use of dedi-

cated metal fittings. Consult with a qualified servicing

engineer or your dealer if other methods are required.

Caution

¡Check the connectors provided on your car (see precaution below) before connecting the system.

¡This unit is designed for use in a car having a 12 V negative ground battery system.

¡To prevent damage to the unit, be sure to follow the connection diagram.

¡Strip about 5 mm of the lead ends for connection (only non-ISO connector cords).

¡Do not insert the power connector into the unit until the wiring is completed.

¡Be sure to insulate any exposed wires to prevent short circuiting with the car chassis. Bundle all cables, and pre-

vent cable terminals from touching any metal parts.

¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery

may clear the memory.

¡Run the cords avoiding the spots where the temperature can be extremely high.

CQ-VD7003N

(Rear)

(For rear connectors, a page 12)

❏ Wiring Diagram

Power Connector

CQ-VD7003N

English

CQ-VD7003N

(Rear)

ACC

SIDE BRAKE

NAVI MUTE

AMP-CONT MAX 0.1A

ANT-CONT MAX 0.1A

BATTERY 15A

Caution

¡Use ungrounded speakers only.

Allowable input : 50 W or more

Impedance : 4 – 8 Ω

¡Distance between speaker and amplifier: 30 cm or more

¡Do not connect more than one speaker to one set of

speaker leads. (except for connecting to a tweeter)

Side Brake (Parking Brake) Connection Lead

(Bright green)

Be sure to wire the side brake (parking brake) for safety

and preventing accidents.

Navi Mute Lead

(Orange)

To navi mute lead of car navigation system.

External Amplifier Control Power Lead

(Blue/white stripe)

To an external amplifier.

Note:

¡Use the power control lead of the TV tuner for TV

tuner connection.

¡Connect both the power control lead of the TV tuner

and the amplifier control connector of the external

amplifier when the TV tuner and external amplifier are

connected at the same time.

A8 (Black)

A7 (Red)

Resistor (1 kΩ)

Noise Filter

A4 (Yellow)

A5 (Blue)

B8 (Green/black stripe)

B7 (Green)

B6 (White/black stripe)

B5 (White)

B4 (Gray/black stripe)

B3 (Gray)

B2 (Violet/black stripe)

B1 (Violet)

Not used.

A5 : Motor Antenna Relay Control Lead

(Blue)

To Motor Antenna (Max. 100 mA).

This lead is not intended for use with a

switch actuated power antenna.

Note:

¡The power antenna extends automati-

cally when the power of this unit is

turned on.

A7 : Power Lead (IGN or ACC) (Red)

To ACC power, +12 V DC.

A8 : Ground Lead (Black)

To a clean, bare metallic part of the car

chassis.

A4 : Battery Lead (Yellow)

To the car battery, continuous +12 V DC.

B8 : Rear Left –

B7 : Rear Left +

B6 : Front Left –

B5 : Front Left +

B4 : Front Right –

B3 : Front Right +

B2 : Rear Right –

B1 : Rear Right +

Speakers

Power Connector

To power connector of the unit.

(Fuse 15 A)

CQ-VD7003N

English

Electrical Connections (continued)

Names and Colors of Rear Connectors

AV-OUT

AV1-IN

AV2-IN

PRE-OUT REAR

S.W-OUT

CAMERA-IN

PRE-OUT CENTER

REMOTE-IN

REVERSE

PRE-OUT FRONT

Power

Connector

(

page 11)

Video Output Terminal (AV-OUT)

Connect the rear monitor. (

a page 18)

System-up Connector

To external devices equipped with system-up connector.

RGB Connector

To the Panasonic Car Navigation System.

Pre-Out Connector (front)

To external amplifier.

Pre-Out Connector (centre)

To external amplifier.

Pre-Out Connector (rear)

To external amplifier.

Pre-Out Subwoofer connector (mono)

To external amplifier.

Video Input Terminal (AV1-IN/AV2-IN)

Connect a VCR, camcorder, other brand’s car

navigation system, etc. (a page 18)

Note: When an external device is connected

to the system-up connector, the audio termi-

nals, {(R)(Red), (L)(White)}, of AV2-IN are

disabled.

Remote-In Lead

To Remote-Out of connected device.

Camera Input Terminal (CAMERA-IN)

Connect a rear view camera (

a page 17) .

Reverse Lead

When connecting the rear view camera, use

the reverse lead.

(R)(Red)

(L)(White)

(R)(Red)

(L)(White)

(R)(Red)

(L)(White)

(Yellow)

(R)(Red)

(L)(White)

(Yellow)

(R)(Red)

(L)(White)

(Yellow)

(Violet/white stripe)

(Brown/black stripe)

(Black)

CQ-VD7003N

(Rear)

ISO Antenna

Adapter

(If needed)

CQ-VD7003N

English

Connection with TV Tuner (CY-TUP153N)

Note:

¡Refer to the operating instructions for the connected devices, in addition.

AV2-IN

PWR-CONT

AMP-CONT MAX 0.1 A

TV Tuner

CY-TUP153N (option)

CQ-VD7003N

(Rear)

(Video)

(Yellow)

(Video)

(Yellow)

RCA Cord

(supplied with CY-TUP153N)

System-up Connector

(supplied with CY-TUP153N)

(not used)

Power

Connector

Power Connector

(supplied with CY-TUP153N)

External Amplifier Control Power Lead

Note:

¡Connect both the power control lead of the TV tuner and the amplifier control con-

nector of the external amplifier when the TV tuner and external amplifier are con-

nected at the same time.

Power Control Lead

Clip connector

(option)

CQ-VD7003N

English

Electrical Connections (continued)

CHANGER IN

BATTERY 5 A

ACC

AV2-IN

Connection with DVD Changer (CX-DH801N)

CQ-VD7003N

(Rear)

RCA Cord

(Video)

(Yellow)

(Video)

(Yellow)

(L) (White)

(R) (Red)

DIN Connector

DIN Cord (Black)

DVD Changer

CX-DH801N (option)

Battery Lead

(Yellow) To the car battery, continuous +12 V DC

Power Lead (Red) (not used)

(not used)

Ground Lead (Black)

To a clean, bare metallic part of the car chassis

Note:

¡Refer to the operating instructions for the connected devices, in addition.

Power Connector

(Supplied with CX-DH801N)

Conversion Cable for DVD/CD Changer

(CA-CC30N, option)

System-up

connector

CQ-VD7003N

English

CHANGER IN

(L) (White)

(R) (Red)

DIN Connector

Conversion Cable for DVD/CD

Changer (CA-CC30N, option)

Connection with CD Changer (CX-DP880N)

CQ-VD7003N

(Rear)

System-up

connector

DIN Cord (Black)

CD Changer

CX-DP880N (option)

Power Connector

(Supplied with CX-DP880N)

RCA Cord

Battery Lead (Yellow)

To the car battery, continuous

+12 V DC

Ground Lead (Black)

To a clean, bare metallic part of the car

chassis

Note:

¡Refer to the operating instructions for the connected devices, in addition.

CHANGER IN

VIDEO-CNT

AV2-IN

CQ-VD7003N

English

Electrical Connections (continued)

Connection with Expansion Module (CY-EM100N)

CQ-VD7003N

(Rear)

Note:

¡Refer to the operating instructions for the connected devices, in addition.

VIDEO OUT

AUDIO OUT

VIDEO OUT

DVD Changer

CX-DH801N (option)

Expansion Module

CY-EM100N (option)

Conversion Cable

for DVD/CD

Changer (CA-

CC30N, option)

Direct Cable for iPod

(CA-DC300N, option)

(Video) (Yellow)

(Video)

(Yellow)

(Video)

(Yellow)

(L) (White)

RCA cord

(option)

(R) (Red)

(Video) (Yellow)

(L) (White)

(R)

(Red)

Head unit/Expansion Module

Connecting cable

(Supplied with CY-EM100N)

Camcorder

(option)

iPod

System-up

Connector

CQ-VD7003N

English

Connection with Rear View Camera

Note:

¡Refer to the operating instructions for the connected devices, in addition.

REVERSE

CAMERA-IN

Connecting the Reverse Lead

If using an optional rear view camera, the reverse lead

must be connected.

Connect the reverse lead (violet/white stripe) to the posi-

tive (+) lead of the reverse lamp (the lamp with a clear

lens that lights when the transmission gear is shifted into

the reverse position).

Note:

¡Connect the reverse lead after cutting the terminal at

the end.

¡Use a Reverse Extension Cord

!2 if needed.

Rear View Camera (option)

(Video)

(Yellow)

RCA Cord (option)

Rear View Camera

Control Unit (option)

CQ-VD7003N

(Rear)

(Video)

(Yellow)

Reverse lamp

Clip connector

(option)

Battery

Car chassis

Transmission gear

Reverse Extension Cord

(Violet/white stripe)

Reverse Lead

(Violet/white stripe)

Camera Input

Camera Input Terminal

(Yellow)

Check the reverse lamp.

Take it out of the back of

the tail lamp mount.

CQ-VD7003N

English

Electrical Connections (continued)

INTELLIGENT SYSTEM

BS G-CODE

POWER

AV1-IN

Connection with Rear Monitor

Note:

¡Refer to the operating instructions for the connected devices, in addition.

¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in

order to establish a proper connection.

AV-OUT

COLOR LCD MONITOR

VM1500

Panasonic

STAND BY (R)

ON (G)

CQ-VD7003N

(Rear)

RCA Cord

(option)

(R) (Red)

(L) (White)

(Video) (Yellow)

Example:

Rear Monitor

Video Input

Audio Right

Audio Left

Connection with VCR or Camcorder

CQ-VD7003N

(Rear)

(R)

(Red)

(L)

(White)

(Video)

(Yellow)

VCR (option)

Camcorder (option)

(R) (Red)

(L) (White)

(Video) (Yellow)

RCA Cord

(option)

Video Output

Audio Left

Audio Right

Note:

¡Refer to the operating instructions for the connected devices, in addition.

¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in

order to establish a proper connection.

Caution

¡For people sitting in the front seats, please

enjoy only audio during driving.

CQ-VD7003N

English

Connection with Car Navigation System (CN-DV2300N)

Note:

¡Refer to the operating instructions for the connected devices, in addition.

NAVI MUTE

CQ-VD7003N

(Rear)

RGB Connector

Power Connector

(Supplied with CN-DV2300N)

RGB Cord

(Supplied with CN-DV2300N)

Navi Mute Lead

(Orange)

Navi Mute Lead

(Orange)

Car Navigation System

CN-DV2300N (option)

Clip connector

(option)

Power Connector

Panasonic CQVD7003N Operating instructions

Panasonic CQVD7003N Operating instructions

Panasonic CQVD7003N Operating instructions

Related papers

Other documents