Panasonic TXP54Z11E Operating instructions

Brand: Panasonic

Model: TXP54Z11E

Category: Plasma TVs

Type: Operating instructions

This manual is also suitable for

TXP46Z11E

TQB0E0888U

Operating Instructions

Plasma Television

Model No. TX-P46Z11E

TX-P54Z11E

Please read these instructions before operating your set and retain them for future reference.

The images shown in this manual are for illustrative purposes only.

Please refer to Pan European Guarantee Card if you need to contact your local Panasonic dealer for assistance.

English

Notice for DVB functions

Any functions related to DVB (Digital Video Broadcasting) will work in areas where ●

DVB-T (MPEG2 and MPEG4-AVC(H.264)) digital terrestrial broadcasting are

received, where DVB-C (MPEG2 and MPEG4-AVC

(H.264)) digital cable services

are supplied or where DVB-S (MPEG2 and MPEG4-AVC

(H.264)) digital satellite

broadcasting are received.

Consult your local dealer with coverage areas or your cable provider to access.

DVB functions may not be available in some countries or areas.

●

Some functions may not be available in some countries or areas.●

Some functions may not be available with some cable provider.●

Some functions may not be available with some satellites.●

This TV has the capability for DVB specifications. But future DVB services cannot ●

be guaranteed.

Turn your own living room into a movie theatre!

Experience an amazing level of multi-

Viewing Advanced FAQs, etc.

Quick Start Guide

This product is licensed under the AVC patent portfolio

license for the personal and non-commercial use of a

consumer to (i) encode video in compliance with the AVC

Standard (“AVC Video”) and/or (ii) decode AVC Video that

was encoded by a consumer engaged in a personal and

non-commercial activity and/or was obtained from a video

provider licensed to provide AVC Video. No license is

granted or shall be implied for any other use.

Additional information may be obtained from MPEG LA, LLC.

See http://www.mpegla.com.

media excitement

Enjoy rich multi-media

Camcorder

Amplifier with

Speaker system

VCR

DVD player

DVD Recorder

Personal

computer

Set top box

SD Card

Up to 100,000 hours Plasma Panel Lifetime

The Plasma display panel used in the 2009 VIERA TV

range is rated for up to 100,000 hours.

∗

This measurement is based on the time taken for the brightness of the

panel to reduce to half of it’s maximum level.

The time taken to reach this level may vary depending on the image

content and the environment where the TV is used.

Image retention and malfunctions are not taken into account.

Contents

Be Sure to Read

Safety Precautions● ············································ 4

(Warning / Caution)

Notes

● ································································· 5

Maintenance● ······················································ 6

Options● ······························································ 6

Quick Start Guide

Accessories● ························· 7

Basic Connection● ·············· 12

Identifying Controls● ············ 14

Auto Setup● ························· 16

Enjoy your TV!

Basic Features

Watching TV● ···················································· 18

Using TV Guide

● ··············································· 22

Viewing Teletext● ··············································· 24

Watching External inputs● ································· 26

How to Use Menu Functions● ··························· 28

(picture, sound quality, etc.)

Advanced Features

Retuning from Setup Menu● ····························· 36

Tuning and Editing Channels (DVB)● ················ 40

Tuning and Editing Channels (Analogue)● ········ 44

Child Lock● ························································ 46

Using Common Interface● ································· 47

Shipping Condition● ·········································· 48

Updating the TV Software● ······························· 49

Input Labels● ····················································· 50

Multi Window● ··················································· 51

Using MHP Services

● ········································ 52

Displaying PC Screen on TV

● ··························· 54

How to Use VIERA TOOLS● ····························· 55

Using Network Services● ·································· 56

(DLNA / VIERA CAST)

Viewing from SD Card● ····································· 64

(VIERA IMAGE VIEWER)

Link Functions

● ················································ 68

(Q-Link / VIERA Link)

External Equipment● ········································· 76

FAQs, etc.

Technical Information● ······································ 78

FAQs

● ······························································· 85

Licence● ···························································· 89

Specifications● ·················································· 90

Safety Precautions

Warning

Handling the mains plug and lead

Insert the mains plug fully into the socket outlet. (If the mains plug is loose, it could generate heat and cause ●

fire.)

Ensure that the mains plug is easily accessible. ●

Ensure the earth pin on the mains plug is securely connected to prevent electrical shock. ●

An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective ●

earthing connection.

Do not touch the mains plug with a wet hand. (This may cause electrical shock.) ●

Do not damage the mains lead. (A damaged lead may cause fire or electrical shock.) ●

Do not move the unit with the lead plugged in the socket outlet. ●

Do not place a heavy object on the lead or place the lead near a high-temperature object. ●

Do not twist the lead, bend it excessively, or stretch it. ●

Do not pull on the lead. Hold onto the mains plug body when disconnecting lead. ●

Do not use a damaged mains plug or socket outlet. ●

If you find any

abnormality,

remove the mains plug

immediately!

AC 220-240 V

50 / 60 Hz

Power source

This TV is designed to operate on 220-240 V, ●

50 / 60 Hz AC.

Do not remove covers

NEVER modify the unit yourself

(High-voltage components may cause serious

electrical shock.)

Do not remove the rear cover as live parts are

●

accessible when it is removed. There are no user

serviceable parts inside.

Have the unit checked, adjusted, or repaired at your

●

local Panasonic dealer.

Do not expose to rain or

excessive moisture

To prevent damage which might result in electric ●

shock or fire, do not expose the unit to rain or

excessive moisture. The unit must not be exposed

to dripping or splashing water and objects filled with

liquid, such as vases, must not be placed on top of

or above the unit.

Do not expose to direct sunlight

and other sources of heat

Avoid exposing the unit to direct sunlight and other ●

sources of heat. To prevent fire never place any type

of candle or naked flame on top or near the unit.

Do not place foreign objects

inside the unit

Do not allow any objects to drop into the unit ●

through the air vents (fire or electrical shock may

result).

Do not place the unit on sloped

or unstable surfaces

The unit may fall off or tip over. ●

Use only the dedicated

pedestals / mounting equipment

Using an unapproved pedestal or other fixtures may ●

make the Display Unit unstable, risking injury. Be

sure to ask your local Panasonic dealer to perform

setup.

Use approved pedestals / mounts (p. 6). ●

Do not allow children to handle

SD Card

As with a small object, SD Card can be swallowed ●

by young children. Please remove SD Card

immediately after use.

Notes

Do not display a still picture ■

for a long time

This causes the image to remain on the

plasma screen (“image retention”).

This is not considered a malfunction and is

not covered by the warranty.

Typical still images

Channel number and ●

other logos

Image displayed in ●

4:3 mode

Video game●

Computer image●

To prevent image retention, contrast is

lowered automatically after a few minutes

if no signals are sent or no operations are

performed. (p. 85)

Auto power standby function ■

If no signal is received and no operation ●

is performed in Analogue TV mode for

30 minutes, the unit will automatically go

to standby mode.

The unit will automatically go to Standby ●

mode if there are no signal and no

operation between the Display Unit and

the Tuner Box for a while.

Tuner Box - after 1 minute

Display Unit - after 10 minutes

Keep the unit away from these ■

types of equipment

Electronic equipment ●

In particular, do not place video equipment

near the unit (electromagnetic interference

may distort images / sound).

Equipment with an infrared sensor ●

This unit also emits infrared rays (this may

affect operation of other equipment).

Adjust the panel to your desired ■

angle (TX-P46Z11E)

Ensure that the pedestal does not hang ●

over the edge of the base even if the TV

swivels to the full rotation range.

Do not place any objects or hands within ●

the full rotation range.

10˚ 10˚

(View from the top)

500 mm

383 mm

Set the mark at the centre as

illustrated, to ensure full degree

rotation in either direction.

When cleaning the unit, remove the mains plug

■

Cleaning an energized unit may cause electrical shock. ●

When the unit is not going to be used for a ■

long period of time, remove the mains plug

The unit will still consume some power even in the Off mode, ●

as long as the mains plug is still connected to a live socket

outlet.

Transport only in upright position ■

Transporting the Display Unit with its display panel facing ●

upright or downward may cause damage to the internal

circuitry.

Allow sufficient space around the Display ■

Unit for radiated heat

Minimum distance

(cm)

When using the pedestal, keep the space between the ●

bottom of the Display Unit and the surface where the Display

Unit is set.

In case of using Wall-hanging bracket, follow the manual of

●

it.

Do not block the rear air vents ■

Blocked ventilation by newspapers, table cloths, curtains, ●

etc. may cause overheating, fire or electrical shock.

Do not expose your ears to excessive ■

volume from the headphones

Irreversible damage can be caused. ●

The Display Unit is heavy. Handle the ■

Display Unit by 2 or more people. Support

as shown to avoid injury by the Display Unit

tipping or falling.

Caution

Maintenance

Options

First, remove the mains plug from the socket outlet.

Display panel

Regular care: Gently wipe the surface clean of dirt by using a soft cloth.

Major contamination: Wipe the surface clean using a soft cloth dampened with clean water or diluted neutral

detergent (1 part detergent to 100 parts water). Then, using a soft dry cloth, evenly wipe the surface clean until it is

dry.

Caution

The surface of the display panel has been specially treated and may be easily damaged.●

Do not tap or scratch the surface with your fingernail or other hard object.

Take care not to subject the surface to insect repellent, solvent, thinner, or other volatile substances (this may ●

degrade surface quality).

Cabinet, Pedestal, Tuner Box

Regular care: Wipe the surface clean using a soft dry cloth.

Major contamination: Dampen a soft cloth with clean water or water containing a small amount of neutral detergent.

Then, wring the cloth and wipe the surface clean with it. Finally, wipe the surface clean with a dry cloth.

Caution

Take care not to subject the unit’s surfaces to detergent. (A liquid inside the unit could lead to product failure.)●

Take care not to subject surfaces to insect repellent, solvent, thinner, or other volatile substances (this may ●

deteriorate the surface by peeling the paint).

Do not allow the cabinet and pedestal to make contact with a rubber or PVC substance for a long time.●

Mains plug

Wipe the mains plug with a dry cloth at regular intervals. (Moisture and dust may lead to fire or electrical shock.)

Optional accessories

Wall-hanging bracket

TY-WK5P1SW●

Please contact your nearest Panasonic dealer to purchase the recommended

wall-hanging bracket. For additional details, please refer to the wall-hanging

bracket installation manual.

Rear of the Display Unit

Holes for wall-hanging

bracket installation

TX-P46Z11E●

a: 472 mm / b: 300 mm

TX-P54Z11E

●

a: 516 mm / b: 300 mm

Caution

In order to maintain the unit’s performance and safety, be absolutely sure to ask your dealer or a licenced ●

contractor to secure the wall-hanging brackets.

Carefully read the instructions accompanying optional accessories, and be absolutely sure to take steps to

●

prevent the Display Unit from tipping over.

Handle the Display Unit carefully during installation since subjecting it to impact or other forces may cause ●

product damage.

Take care when fixing wall brackets to the wall. Always ensure that there are no electrical cables or pipes in

●

the wall before hanging bracket.

To prevent fall and injury, remove the Display Unit from its fixed wall position when it is no longer in use.

●

Accessories ●

Maintenance ●●Options

Quick Start Guide

Accessories

Pedestal □

p. 8

Pedestal installation kit □

p. 8

(2)

(4)

Speaker (2) □

p. 10

Standard accessories■

Check that you have the accessories and items shown

Display Unit □

Remote Control □

N2QAYB000353●

abc def

jkl

ghi

mno

tuvpqrs

wxyz

Batteries for the □

Remote Control (2)

R6 (UM3)●

Cleaning cloth □

Clamper (2) □

p. 14

Tuner Box □

p. 12

Ferrite core (2) □

p. 77

Use the Ferrite cores to

comply with the EMC

standard.

HDMI cable □

p. 12

Speaker installation kit □

p. 10

(8) (8)

Operating Instructions □

Pan European Guarantee Card □

This product contains possibly dangerous parts (such as plastic bags), that can be breathed in or swallowed by ●

young children accidentally. Keep these parts out of reach of young children.

Accessories

Installing / removing remote’s batteries

Pull

open

Hook

Note the correct

polarity (+ or -)

Caution

Incorrect installation may cause battery leakage and corrosion, resulting in damage to the remote control.●

Do not mix old and new batteries.●

Do not mix different battery types (such as alkaline and manganese batteries).●

Do not use rechargeable (Ni-Cd) batteries.●

Do not burn or breakup batteries.●

Batteries must not be exposed to excessive heat such as sunshine, fire or the like.

Do not disassemble or modify the remote control.●

Attaching the pedestal

Warning

Do not disassemble or modify the pedestal.

Otherwise the Display Unit may fall over and become damaged, and personal injury may result. ●

Caution

Do not use any other TV and displays.

Otherwise the TV may fall over and become damaged, and personal injury may result. ●

Do not use the pedestal if it becomes warped or physically damaged.

If you use the pedestal while it is physically damaged, personal injury may result. Contact your nearest Panasonic ●

dealer immediately.

During set-up, make sure that all screws are securely tightened.

If insufficient care is taken to ensure screws are properly tightened during assembly, the pedestal will not be ●

strong enough to support the Display Unit, and it might fall over and become damaged, and personal injury may

result.

Ensure that the Display Unit does not fall over.

If the Display Unit is knocked or children climb onto the pedestal with the Display Unit installed, the Display Unit ●

may fall over and personal injury may result.

Two or more people are required to install and remove the Display Unit.

If two or more people are not present, the Display Unit may be dropped, and personal injury may result. ●

Pedestal

TBLX0105 (TX-P46Z11E)●

TBLX0107 (TX-P54Z11E)●

Base

TBLA0421 (TX-P46Z11E)●

TBLA0460 (TX-P54Z11E)●

Frame

TBLA0462 (TX-P46Z11E)●

TBLA0464 (TX-P54Z11E)●

Pedestal installation kit

TXFEL01DMUB● TXFBL01JUUJ●

Assembly screw (2)

(Silver)

XYN8+F30FN●

Assembly screw (4)

(Black)

XSB4+10FNK●

Assembly screw (4)

(Black)

THEL062N●

M8 × 30 M4 × 10 M5 × 25

Holder cover

TBLB3416●

Accessories ●

Quick Start Guide

Assembling the pedestal■

Remove the Cable cover from the Frame .

Cable cover will be used again after the ●

pedestal is attached to the Display Unit.

Cable cover

Use the assembly screws to fasten securely.

Make sure that the screws are securely tightened.●

Be careful not to scratch the surface (part with gloss finish) of the base during assembly.●

Hole for the

Base installation

Securing the Display Unit■

Slide the pedestal frame posts into the brackets on

the rear of the Display Unit.

Use the assembly screws to fasten securely.

Make sure that the screws are securely tightened.●

Attach the Holder cover with assembly screws .

Make sure that the screws are securely tightened.

●

Attach the Cable cover.

Cable cover

Place a cable in ●

the groove as

necessary and

attach the Cable

cover.

The lower part

of the groove is

separated in right

and left. Use the

one suitable for

you.

Accessories

Attaching the Speakers

Speaker

SP-46Z1E (TX-P46Z11E) ●

SP-54Z1E (TX-P54Z11E) ●

Speaker (2)

Speaker installation kit

TXFKR01JXUE●

Mounting bracket-[Top] (2)

TXFKR04DLUJ●

Mounting bracket-[Lower right]

TXFKR05DLUJ●

Mounting bracket-[Lower left]

TXFKR06DLUJ●

Assembly screw

TXFXY01DLUJB●

Speaker cable (2)

TXJ/SPDKUU-1●

(8)

Use the assembly screws - to fasten the Mounting

brackets to the rear of the Display Unit securely.

Make sure that the screws are securely tightened.●

Note

Loosen these screws to ●

adjust the gap between the

Speaker and the Display Unit

as necessary.

E-a

Ensure that the silver

part is facing the front

Display Unit

Insert the assembly screws - temporarily in the

screw outermost holes of the Speaker and place

the temporarily inserted screws into the counter sunk

holes on the Mounting brackets .

E-- b

Accessories ●

Quick Start Guide

Use another two assembly screws - to fasten the

Speaker to the Mounting brackets .

E-- b

Adjust the speaker position and make sure that the

assembly screws - are securely tightened.

E b

Connect the Speaker and the Display Unit with the

Speaker Cable

Insert the terminal firmly.

●

Connect the terminal near the Ferrite core to the Display ●

Unit.

Fix the cable with the clamper on the Mounting bracket ●

Push here to

remove the hook

hook

Fix the cable

Display Unit

clamper

Ferrite core

terminal

Note

Fix the other side speaker in the same way.●

There will be a gap between the Display Unit and the Speaker.●

Do not hold the Speaker part to transport the Display Unit.●

Basic Connection

Connecting the Display Unit and the Tuner Box

Please ensure that the unit is disconnected from the mains socket before attaching or disconnecting any

leads.

Tuner Box

TU-Z100E●

HDMI cable

K1HY19YY0004●

AUDIO

COMPONENT

AUDIO

OUT

DIGITAL

AUDIO OUT

HDMI 1

HDMI 2 HDMI 3

Rear of the Display Unit

Rear of the Tuner Box

This terminal is not used

for this model.

Mains lead

AC 220-240 V

50 / 60 Hz

Mains

lead

Tuner Box

K1HY19YY0006

●

HDMI cable

3.0 m

Connecting the Tuner Box and dish / aerial / external equipment

External equipment and cables shown are not supplied with this TV.

Please ensure that the unit is disconnected from the mains socket before attaching or disconnecting any

leads.

Read the manual of the equipment too.●

Example 1■

Connecting dish or aerial (TV only)

AV 2

AV 1

AUDIO

COMPONENT

AUDIO

OUT

DIGITAL

AUDIO OUT

HDMI 1

RGB

VIDEO

S VIDEO

RGB

VIDEO

HDMI 2 HDMI 3

Rear of the Tuner Box

cable

Terrestrial

aerial

For digital cable, ●

digital terrestrial

and analogue

broadcasts

Mains lead

AC 220-240 V

50 / 60 Hz

Satellite

dish

Satellite

cable

For digital satellite ●

broadcasts

Cable

Selectable satellites and dish alignment to tune DVB-S channels:

Turksat at 42° East•

Hellas at 39° East•

Astra at 28.2° East•

Arabsat at 26° East•

Astra at 23.5° East•

Astra at 19.2° East•

Eutelsat at 16° East•

Hot Bird at 13° East•

Eutelsat at 10° East•

Eurobird at 9° East•

Eutelsat at 7° East•

Sirius at 5° East•

Intelsat at 1° West•

Amos at 4° West•

Atl. Bird at 5° West•

Atl. Bird at 7° West•

Atl. Bird at 8° West•

Hispasat at 30° West•

To ensure your satellite dish is correctly installed, please consult your local dealer.●

Also please consult the received satellite broadcasting companies for details.●

Basic Connection ●

Quick Start Guide

Example 3■

Connecting DVD Recorder / VCR and Set top box

RF OUT

RF IN

AV 2

AV 1

AUDIO

COMPONENT

AUDIO

OUT

DIGITAL

AUDIO OUT

HDMI 1

RGB

VIDEO

S VIDEO

RGB

VIDEO

HDMI 2 HDMI 3

DVD Recorder or

VCR

Fully wired

SCART cable

RF cable

Fully wired HDMI

compliant cable

Set top box

Cable

Rear of the Tuner Box

Terrestrial

aerial

Mains lead

AC 220-240 V

50 / 60 Hz

Connect to the TV’s AV1 / AV2 for a DVD Recorder / VCR supporting Q-Link (p. 70).●

Example 2■

Connecting DVD Recorder / VCR

RF OUT

RF IN

AV 2

AV 1

AUDIO

COMPONENT

AUDIO

OUT

DIGITAL

AUDIO OUT

HDMI 1

RGB

VIDEO

S VIDEO

RGB

VIDEO

HDMI 2 HDMI 3

RF cable

Fully wired

SCART cable

DVD Recorder or VCR

Rear of the Tuner Box

Terrestrial

aerial

Mains lead

AC 220-240 V

50 / 60 Hz

Cable

Connect to the TV’s AV1 / AV2 for a DVD Recorder / VCR supporting Q-Link (p. 70).●

Note

For HDMI-compatible equipment, possible to connect to HDMI terminals (HDMI1 / HDMI2 / HDMI3 / HDMI4) by ●

using HDMI cable (p. 76).

Network connection ● p. 57

Q-Link connection ● p. 68

VIERA Link connection ● p. 68 and p. 69

HDMI 4

AV3

S-V

PC AUDIO

via AV3

Identifying Controls

Display Unit

Tuner Box

Remote control signal receiver

Do not place any objects between the TV remote control signal receiver and remote control. ●

Function select

Volume / Contrast / Brightness / ●

Colour / Sharpness /

Tint (NTSC mode) / Bass / Treble /

Balance / Auto Setup (p. 36, 38, 39)

Recording LED

Standby for Direct TV Recording: orange●

Power LED

Standby: red●

On: green

When using the remote control, indicates

●

the TV has received a command.

Power LED

Standby: red●

On: green

When using the remote control, indicates the TV has received a command.

●

Mains power On / Off switch

Turn the Display Unit On or Off. ●

When turning Off the Display Unit,

Tuner Box will also be turned to

Standby mode after 1 min.

Standby switch

Turn the Tuner ●

Box on or off to

standby mode

Selects channel in sequence

Changes the input mode

HDMI4 terminal

(p. 76)

SD Card slot

(p. 64)

AV3 terminals

(p. 76)

Headphones jack

(p. 76)

PC terminal

(p. 76)

Selects channel in sequence

Volume Up / Down

C.A.T.S. (Contrast Automatic Tracking System) sensor

Senses brightness to adjust picture quality when ●

“Eco Mode” in the Picture Menu is set to “On” (p. 30)

Using the clamper

Fix cables with clampers as necessary.●

When using the optional accessory, follow the option’s ●

assembly manual to fix cables.

Rear of the Display Unit

snaps

To loosen:

Keep

pushing both

side snaps

Set the

tip in the

hooks

Insert the clamper

in a hole

Attach the clamper■ Bundle the cables■

Keep

pushing

the knob

knob

hooks

To remove from the TV:

hole

Basic Connection

Identifying Controls ●

Basic Connection ●

Quick Start Guide

EXIT

ASPECT

OPTION

TEXT

REC

PROGRAMME

STTL

INDEX HOLD

BACK/

RETURN

INPUT

DVD/VCR

AVTV

abc def

jkl

ghi

mno

tuvpqrs

wxyz

DIRECT TV REC

Remote Control

Cursor buttons

Makes selections and adjustments●

Standby On / Off switch

Switches TV On or Off standby●

Sound Mute

Switches sound mute On or Off●

Aspect (p. 20)

Changes aspect ratio from Aspect Selection

●

list

Also possible by pressing this button

●

repeatedly until you reach the desired aspect

Channel Up / Down

Selects channel in sequence●

Connected equipment operations

(p. 27 and p. 74)

Teletext (p. 24)

Switches to teletext mode

●

Confirms selections and choices●

Press after selecting channel positions ●

to quickly change channel

Volume Up / Down

Channel / Programme Information

(p. 19)

Displays channel and programme

●

information

Index (p. 25)

Returns to the teletext index page

●

(teletext mode)

Coloured buttons

Used for the selection, navigation and ●

operation of various functions

Exit

Returns to the normal viewing screen●

Numeric buttons

Changes channel and teletext pages●

Sets characters●

When in Standby mode, switches TV On●

VIERA Link Menu (p. 72)

Accesses VIERA Link Menu

●

Guide (p. 22)

Displays TV Guide

●

Option Menu (p. 21)

Easy setting for viewing and

●

sound options

Main Menu (p. 28)

Press to access Picture, Sound and

●

Setup Menus

Subtitles (p. 20)

Displays subtitles●

Input mode selection

TV - switches DVB-S / DVB-C / DVB-T / ●

Analogue mode (p. 18)

AV - switches to AV input mode from Input

●

Selection list (p. 26)

VIERA IMAGE VIEWER (p. 64)

Switches to SD Card viewing mode

●

Return

Returns to the previous menu / page●

Hold

Freeze / unfreeze picture (p. 19)●

Holds the current teletext page (teletext ●

mode) (p. 24)

VIERA CAST (p. 63)

Displays VIERA CAST home screen

●

Direct TV Recording (p. 70 and p. 72)

Records programme immediately in

●

DVD Recorder / VCR with Q-Link or

VIERA Link connection

Surround (p. 31)

Switches Surround sound

●

VIERA TOOLS (p. 55)

Displays some special feature icons and

●

accesses easily

Identifying Controls

DIRECT TV REC

ASPECT

INPUT

AVTV

OPTION

TEXT

REC

PROGRAMME

STTL

INDEX HOLD

DVD/VCR

EXIT

BACK/

RETURN

Auto Setup

Search and store TV channels automatically.

These steps are not necessary if the setup has been completed by your local dealer.●

Please complete preparations and setup of all units before starting Auto Setup. (p. 8 - 12)●

Please complete connections (p. 12 and p. 13) and settings (if necessary) of the connected equipment before ●

starting Auto Setup. For details of settings for the connected equipment, read the manual of the equipment.

Plug the Display Unit and Tuner Box into

mains socket, and then turn the Display Unit on

Takes a few seconds to be displayed.●

Select the language

Menüsprache

Nederlands

Português

Español

Italiano

Français

English

Deutsch

Latviešu

Slovenščina

Hrvatski

Lietuvių

eesti keel

Srpski

Românǎ

Български

Slovenčina

Magyar

čeština

Polski

Еλληνικά

Türkçe

Suomi

Norsk

Svenska

Dansk

select

set

Select your country

Country

Italy

France

Austria

Germany

Hungary

Czech

Slovakia

Poland

Finland

Norway

Sweden

Denmark

Malta

Switzerland

Portugal

Spain

Slovenia

Lithuania

Estonia

E.Eu

Turkey

Andorra Greece

Netherlands

Belgium

Luxembourg

select

set

Auto Setup starts

Auto Setup will start to search for TV ●

channels and store them.

The sorted channel order depends upon

the TV signal, the broadcasting system and

reception conditions.

Sending Preset Data

Please wait!

Remote control unavailable

0% 100%

If Q-Link, VIERA Link or similar technology ●

(p. 70) compatible recorder is connected,

channel, language, country / region

settings are automatically downloaded to

the recorder.

If downloading has failed, you can ●

download later by the menu item.

“Download” (p. 32)

Select “Home”

Please select your viewing environment.

Home Shop

set

select

Auto Setup is now complete and your TV is ready for viewing.

To check channel list at-a-glance●

“Using TV Guide” (p. 22 and p. 23)

To edit channels●

“Tuning and Editing Channels” (p. 40 - 45)

Auto Setup ●

Quick Start Guide

Using the On Screen Displays

Many features available on this TV can be accessed via the On Screen Display menu.

How to use remote control

■

Move the cursor / select the menu item

Move the cursor / adjust levels / select from

a range of options

Access the menu / store settings after

adjustments have been made or options

have been set

BACK/

RETURN

Return to the previous menu

Open the main menu

EXIT

Exit the menu system and return to the

normal viewing screen

ON SCREEN HELP Instructions box - Operation guide■

(example: Sound Menu)

Select

EXIT

Change

RETURN

Mode Music

Bass

Treble

Balance

Headphone Volume

Surround Off

Volume Correction

Speaker Distance to Wall

Over 30cm

MPX Stereo

Sound Menu 1/2

Stereo

Page up

Page down

Operation guide will help you.

Auto Setup varies depending on the country you select■

Depending on the country you select, you may be required to select the Favourite Network or Region.

Search Mode

●

(

if you select “Germany”,

“Austria”, “Switzerland”,

“Sweden” or “Finland”

)

Search Mode

All Channels Free Channels

select mode

set

DVB-S Auto Setup●

(if you select “Germany”, “Austria” or “Switzerland”)

DVB-S Auto Setup

Analogue Scan 21 68

Satellite

Searching Satellite

This will take up to 15 minutes.

Satellite

Analogue Scan 68

Progress

Checking LNB2

0 100%

Press EXIT to skip Satellite installation

Astra 19.2°E

Hot Bird 13°E

DVB-S Auto Setup

Analogue Scan 21 68

No. Channel Name Type Quality

Searching Satellite

This will take about 30 minutes.

Satellite

Analogue Scan 68

Progress

Checking LNB1

0100%

Free TV: 3 Pay TV: 0 Radio: 0

372 CBBC Channel Free TV 10

372 BBC Radio Wales Free TV 10

372 E4 Free TV 10

Satellite Search:

If you have only one LNB (not having

DiSEqC control antenna system), you

can skip this step by pressing the EXIT

button.

Analogue Auto Setup● DVB-T Auto Setup●

(

if you select a country

except “Portugal”, “Poland”,

“Hungary” and “E.Eu”

)

DVB-C Auto Setup●

(

if you select

“Sweden” or “Finland”

)

Auto Setup - DVB-T and Analogue

CH Channel Name Type Quality

Searching

This will take about 6 minutes.

Free TV: 4 Pay TV: 0 Radio: 0 Data: 0

Analogue Scan CH 2 CC 21 4199

DVB-T Scan CH 5 69

Analogue: 2

62 CBBC Channel Free TV 10

62 BBC Radio Wales Free TV 10

62 E4 Free TV 10

62 Cartoon Nwk Free TV 10

29 Analogue

33 BBC1 Analogue

Auto Setup - DVB-T and Analogue

CH Channel Name Type Quality

Searching

This will take about 6 minutes.

Free TV: 4 Pay TV: 0 Radio: 0 Data: 0

Analogue Scan CH 2 CC 21 4199

DVB-T Scan CH 5 69

Analogue: 0

62 CBBC Channel Free TV 10

62 BBC Radio Wales Free TV 10

62 E4 Free TV 10

62 Cartoon Nwk Free TV 10

DVB-C Auto Setup

Analogue Scan 21 68

No. Channel Name Type Quality

Searching

This will take about 3 minutes.

Progress 0% 100%

Free TV: 3 Pay TV: 0 Radio: 0 Data: 0

1 CBBC Channel Free TV 10

2 BBC Radio Wales Free TV 10

3E4 Free TV10

If you select “Shop” by mistake■

Return to viewing environment selection by

pressing the RETURN button.

Select “Home”

Auto Setup is complete

Automatic Demo

Off On

BACK/

RETURN

Please select your viewing environment.

Home Shop

If you set to “Off” or “On” in this menu the ●

TV will be in “Shop” viewing environment.

To return to “Home” viewing environment

initialise all settings by accessing

Shipping Condition.

“Shipping Condition” (p. 48)

select

set

Note

If tuning has failed ● “Auto Setup” (p. 36 - 39)

To initialize all settings ● “Shipping Condition” (p. 48)

If you turned the Display Unit Off during Standby mode last time, the Display Unit will be in Standby mode when ●

you turn it On with Mains power On / Off switch.

BACK/

RETURN

TEXT

INDEX

REC

PROGRAMME

DVD/VCR

EXIT

ASPECT

OPTION

STTL

HOLD

INPUT

abc def

jkl

ghi

mno

tuvpqrs

wxyz

Watching TV

Select a channel using Information banner ■ (p. 19)

Possible to confirm the channel name and programme before changing channels.

Display Information banner if it is

not displayed

While the banner is displayed,

select the channel

select channel

watch

Possible to set display timeout in ●

“Banner Display Timeout” (p. 34).

Select a channel using TV Guide ■ (p. 22)

Possible to confirm the TV Guide (EPG or Channel List) before changing channels.

This function may not be available in some countries.

●

Display TV Guide Select the channel

select

watch

Volume

Turn power on

(Press for about 1 second)

Mains power On / Off switch of the Display Unit should be On. ●

(p. 14)

Select the mode

TV Selection

DVB-C

DVB-S

DVB-T

Analogue

watch

select

The selectable modes vary depending on the country you select (p. 16).●

If “TV Selection” menu is not displayed, press the TV button to switch the ●

mode.

1 BBC ONE WALES

20:35

Coronation Street

20 : 00 - 20 : 55

Now

For info press

Change category

All DVB-T Channels

Information banner appears whenever you select a

channel

For details ● p. 19

Also possible to select the mode pressing the TV button repeatedly on the ●

remote control or front of the Tuner Box. (p. 14)

Select a channel

down

abc def

jkl

ghi

mno

tuvpqrs

wxyz

To select a more than two-digit channel ●

position number, e.g. 399

def

wxyz

To select from the Channel List ●

All DVB-T Channels

Cartoon Nwk

BBC Radio Wales

BBC ONE Wales

BBC Radio Cymru

BBC THREE

BBCi

CBBC Channel

watch

select channel

Note

To watch pay-TV ●

“Using Common

Interface”

(p. 47)

Watching TV ●

Viewing

Hold

Freeze / unfreeze picture

HOLD

Display Information banner

1 ZDF

20:35Radio

Coronation Street

20 : 00 - 20 : 55

Now

For info press

Change category

All DVB-T Channels

Encrypted Dolby D +

Panasonic TXP54Z11E Operating instructions

Brand: Panasonic

Model: TXP54Z11E

Category: Plasma TVs

Type: Operating instructions

This manual is also suitable for

TXP46Z11E

Download PDF

report

Panasonic TXP54Z11E Operating instructions

This manual is also suitable for

Panasonic TXP54Z11E Operating instructions

Related papers

Other documents