All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
RNO, RNOV
Revised 11/25/14 Page 1/3
Renaissance
®
27” and 30” Wide
Double Wall Ovens
Document # PG01-016
Model
(A) Overall
Width
(B) Chassis
Width
(C) Overall
Height
(D)* Chassis
Height
(E) Control
Panel
Overlay
RNO[V]227
26 7/8”
(68.3 cm)
25 1/2”
(64.8 cm)
50 1/8”
(127.3 cm)
49 3/4”
(126.4 cm)
3/8”
(1.0 cm)
RNO[V]230
29 7/8”
(75.9 cm)
28 1/2”
(72.4 cm)
50 1/8”
(127.3 cm)
49 3/4”
(126.4 cm)
3/8”
(1.0 cm)
* To top of chassis notch behind control panel
(F) Utility
Cutout Width
(G) Utility
Cutout Height
(H) Utility
Cutout Depth
(J) Control
Panel Depth
(K) Chassis
Depth
(L) Control
Panel Notch
Depth
(M) Notch
Height
6 1/2”
(16.5 cm)
5”
(12.7 cm)
7 7/8”
(20.0 cm)
3/4”
(1.9 cm)
24”
(61.0 cm)
1/2”
(1.3 cm)
3/4”
(1.9 cm)
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
accompanying installation instructions.
Conduit:
60” (152 cm)
long
Control panel
side view
Control panel
front
Top of
chassis
Top of
chassis
Utility
cutout
C
A
D
J
H
K
E
L
M
B
G
F
21 1/2”
(54.6) cm
ELECTRICAL SPECIFICATIONS
Model
Dedicated Circuit
Requirements
Total Connected Load
RNO[V]227
240 Vac 60 Hz., 4-wire,***
40 Amp.
240 Vac 60 Hz,
39.4 Amp., 9.5 kW
RNO[V]230
240 Vac 60 Hz., 4-wire,***
50 Amp.
240 Vac 60 Hz,
48.6 Amp., 12.0 kW
*** Two 120 Vac hot (L1 and L2), one neutral, one ground
The above specifications are for reference only. See the appliance data
plate for exact specifications.
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
2 3/8”
(6.0 cm)
1 7/8”
(4.8 cm)
Handle Dimensions
Epicure
Millennia
(Order kit #AROVH30S)
Flush
DOUBLE WALL OVEN - CUTOUT DIMENSIONS
Minimum interior cabinet depth: 24” (61.0 cm)
4” typical toe kick
Recommended
electrical
location
N
P
R
3/4” (1.9 cm)
support platform
1” (2.5 cm) min.
to bottom of
cabinet door
1” (2.5 cm) min.
to top of
drawer face
9 5/8” (24.4 cm)
recommended
Model
(N) Minimum
Cabinet
Width
(P) Cut Out Width
(R) Minimum Cutout
Height
RNO[V]227
27”
(68.6 cm)
25 5/8” (65.1 cm)
minimum (recommended)
26 1/8” (66.4 cm)
maximum
49 7/8”
(126.7 cm)
RNO[V]230
30”
(76.2 cm)
28 5/8” (72.7 cm)
minimum (recommended)
29 1/8” (74.0 cm)
maximum
49 7/8”
(126.7 cm)
RNO, RNOV
Revised 11/25/14 Page 2/3
Renaissance 27” and 30” Wide
Double Wall Ovens
Document # PG01-016
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
FRONT VIEWSIDE VIEW
T
W
X
Finished
stops *
U
V
TOP VIEW
VENTILATION
INSET
3/4” (1.9 cm)
** 1 1/8” (2.9 cm) for models
RNO[V]227B, RNO[V]230B,
RNO227W, RNO230W
1” (2.5 cm) **
Cabinet
face
RNO, RNOV
Document # PG01-016
Revised 11/25/14 Page 3/3
Renaissance 27” and 30” Wide,
Double Wall Oven
CUTOUT DIMENSIONS - FLUSH INSTALLATION
DOUBLE WALL OVEN
Model
(T) Minimum
Cabinet Depth
(U) Cutout
Width
(V) Cutout Height (W) Stop Depth (X) Stop Width
RNO227[F]S 24 3/4” (62.9 cm) 27” (68.6 cm) 49 7/8” (126.7 cm) 3/4” (1.9 cm) 3/8” (1.0 cm)
RNO230[F]S 24 3/4” (62.9 cm) 30” (76.2 cm) 49 7/8” (126.7 cm) 3/4” (1.9 cm) 3/8” (1.0 cm)
RNO[V]227B, RNO227W 24 7/8” (63.2 cm) 27” (68.6 cm) 49 7/8” (126.7 cm) 7/8” (2.2 cm) 3/8” (1.0 cm)
RNO[V]230B, RNO230W 24 7/8” (63.2 cm) 30” (76.2 cm) 49 7/8” (126.7 cm) 7/8” (2.2 cm) 3/8” (1.0 cm)
* Back of wall oven control panel rests against stops
Cabinet tolerances: +1/16” (+1.6 mm) -0,
unless otherwise stated
-
1
-
2
-
3
