Avital Automobile Alarm 740T User manual

Brand: Avital

Model: Automobile Alarm 740T

Category: Remote starters

Type: User manual

This manual is also suitable for

HHoorrnneett 774400TT

OOwwnneerr''ss GGuuiiddee

2004 Directed Electronics, Inc.

LLiimmiitteedd LLiiffeettiimmee

CCoonnssuummeerr WWaarrrraannttyy

For a period of one calendar year from the date of purchase of this auto-security

device, Directed Electronics, Inc. promises to the ORIGINAL PURCHASER to repair or

replace (with a comparable reconditioned model), free of cost, any electronic control

module which proves to be defective in workmanship or material under normal use,

SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL

AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY

INSTALLED. If warranty service is necessary you must have a clear copy of your sales

receipt containing all of the information shown on the following page.

After the first calendar year, from the date of purchase of this auto-security device,

Directed Electronics, Inc., promises to the ORIGINAL PURCHASER to repair or replace

(with a comparable reconditioned model) any electronic control module which proves

to be defective in workmanship or material under normal use

FFOORR AA CCHHAARRGGEE OOFF

$$4455..0000,,

SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PRO-

FESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS

ORIGINALLY INSTALLED. If warranty service is necessary you must have a clear copy

of your sales receipt containing all of the information shown on the following page.

This warranty contains the entire agreement relating to warranty and supersedes all

previous and contemporaneous representations or understandings, whether written or

oral. IN ANY EVENT, DIRECTED ELECTRONICS, INC. IS NOT LIABLE FOR THE THEFT OF

THE VEHICLE AND/OR ITS CONTENTS.

This warranty is void if the product has been damaged by accident, unreasonable use,

neglect, improper service or other causes not arising out of defects in materials or

construction. This warranty is nontransferable and does not apply to any unit that

has been modified or used in a manner contrary to its intended purpose and does not

cover batteries. The unit in question must be returned to the manufacturer, postage

prepaid. This warranty d

oes not cover labor costs for the removal, diagnosis, trou-

bleshooting or reinstallation of the unit. For service on an out-of-warranty product a

flat rate fee by model is charged. Contact your authorized dealer to obtain the ser-

vice charge for your unit.

These systems are a deterrent against possible theft. Directed Electronics, Inc. is not

offering a guarantee or insuring against the theft of the automobile or its contents

and disclaims any liability for the theft of the vehicle and/or its contents. Directed

Electronics does not authorize any person to create for it any other obligation or lia-

bility in connection with this security system.

iiii

2004 Directed Electronics, Inc.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUD-

ED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COM-

MERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLU-

SION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WAR-

RANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF

NON-INFRINGEMENT OF PATENTS, IN THE UNITED STATES OF AMERICA AND/OR

ABROAD. NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREWITH

SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT

NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, TOWING,

REPAIR, REPLACEMENT, DAMAGES FOR LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL

LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE

ABOVE, MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR

THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on

how long an implied warranty will last or the exclusion or limitation of incidental or

consequential damages. This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

$$22,,550000 LLiimmiitteedd TThheefftt PPrrootteeccttiioonn GGuuaarraanntteeee

Terms and Conditions. Available only in the USA. In the event that your vehicle is

stolen and not recovered, Directed Electronics, Inc. will refund to the original pur-

chaser of the Avital system up to $2,500 of your insurance deductible. This vehicle

protection guarantee is valid only if:

(1) The installation was performed by an authorized Avital dealer.

(2) The warranty registration card is completed and mailed within ten (10) days of

purchase.

(3) At the time of the theft, the system was fully functional and not in “valet®

mode.”

(4) The vehicle and its contents were insured at the time of the theft.

(5) The insurance company and the police have been notified and a written stolen

vehicle report was issued by the Police Department.

(6) No less than thirty (30) days

aafftteerr

the police report was issued, you mail Directed

Electronics, Inc. clear photocopies of the following documents:

a. Proof of Purchase OR provide the system model and name of the company

that installed the system.

b. The stolen vehicle report issued by the police.

c. Insurance coverage documents for the stolen vehicle, clearly showing all the

details, including the vehicle identification number and the insurance

deductible amount.

d. A dated declaration signed by you the owner of the vehicle, attesting that

the vehicle has been stolen for more than thirty (30) days and has not been

recovered.

iiiiii

2004 Directed Electronics, Inc.

This vehicle theft protection is effective for one (1) year from the date of purchase

and is limited to one claim. This vehicle theft protection guarantee is valid only for

the theft of the entire vehicle and specifically excludes any other considerations,

including, but not limited to, damage caused to the vehicle, theft of parts, contents

or any other consequential damages. Once Avital Technologies verifies that all the

above listed terms and conditions have been met, a check for the insurance

deductible (up to $2,500) will be mailed within thirty (30) days.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

■ Date of purchase

■ Your full name and address

■ Authorized dealer's company name and address

■ Type of alarm installed

■ Year, make, model and color of the automobile

■ Automobile license number

■ Vehicle identification number

■ All security options installed on automobile

■ Installation receipts

2004 Directed Electronics, Inc.

TTaabbllee ooff CCoonntteennttss

LLiimmiitteedd LLiiffeettiimmee CCoonnssuummeerr WWaarrrraannttyy .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ii

hhaatt iiss IInncclluuddeedd .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 33

IImmppoorrttaanntt IInnffoorrmmaattiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. 33

System Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Your Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

FCC/ID Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

RReemmoottee FFuunnccttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. 55

Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

UUssiinngg YYoouurr SSyysstteemm .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 66

Arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Disarming Without a Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remote-Controlled Silent Arm/Disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Valet® Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remote-Controlled Valet® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Nuisance Prevention® Circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DDiiaaggnnoossttiiccss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. 1111

Disarming Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Arming Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Table of Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

SStteeaalltthh CCooddiinngg™™ TTeecchhnnoollooggyy .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1144

HHiigghh FFrreeqquueennccyy .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. 1144

PPrrooggrraammmmiinngg OOppttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. 1155

SSeeccuurriittyy && CCoonnvveenniieenncceeEExxppaannssiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. 1166

IInnssttaallllaattiioonn OOppttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. 1177

GGlloossssaarryy ooff TTeerrmmss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. 1188

QQUUIICCKK RREEFFEERREENNCCEE GGUUIIDDEE .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. 2211

2004 Directed Electronics, Inc.

WWhhaatt iiss IInncclluuddeedd

■ A control module

■ Two 3-button remotes

■ A zone 2 impact sensor on-board the control module

■ A high-powered siren

■ A fault-proof starter interrupt on-board the control module

■ An LED system status indicator

■ A push-button Valet

switch

IImmppoorrttaanntt IInnffoorrmmaattiioonn

Congratulations on the purchase of your state-of-the-art vehicle

security system. This system has been designed to provide years of

trouble-free operation. By carefully reading this guide prior to

using your system, you will maximize the use of this product and

its features.

Your vehicle security system has no specific maintenance require-

ments. The remote is powered by a lightweight 3-volt lithium

battery that will last approximately one year under normal use.

When the battery begins to weaken, the LED on the remote will dim

and you will notice reduced operating range when using the

SSyysstteemm MMaaiinntteennaannccee

2004 Directed Electronics, Inc.

remote. To access the battery for replacement, remove the rear

cover of the remote with a small, flat-blade screwdriver.

Your warranty card must be returned and the barcode serial num-

ber must not be removed. If the warranty card is not returned, no

warranty will be honored on your unit. It is also necessary to keep

your proof of purchase, which reflects that the product was

installed by an authorized dealer. Make sure you receive the war-

ranty card from your dealer.

This device complies with Part 15 of FCC rules. Operation is subject to

the following conditions: (1) This device may not cause harmful inter-

ference, and (2) This device must accept any interference received,

including interference that may cause undesirable operation.

CCaauuttiioonn::

Changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to

operate this device.

FFCCCC//IIDD NNoottiiccee

YYoouurr WWaarrrraannttyy

2004 Directed Electronics, Inc.

RR ee mm oo tt ee FFuunnccttiioonnss

This system is programmable, making it possible to assign any

remote button to any specific receiver function. The remote initial-

ly comes programmed with Standard Configuration, but may also be

customized by an authorized dealer. The buttons in all of the instruc-

tions in this manual correspond to a Standard Configuration remote.

BBuuttttoonn

The arm/disarm/panic functions are usually controlled by .

BBuuttttoonn

An optional accessory function (such as trunk release), remote-

controlled silent arm/disarm, and remote-controlled Valet

are

usually controlled by . (Silent arm/disarm and remote-

controlled Valet® work by pressing for less than one second.

An optional accessory can be controlled by pressing and holding

for 1.5 seconds.)

This accessory output controls ____________________________.

aanndd BBuuttttoonnss

Press these two buttons simultaneously to activate another option-

al accessory.

This accessory output controls ____________________________.

AUX

SSttaannddaarrdd CCoonnffiigguurraattiioonn

2004 Directed Electronics, Inc.

BBuuttttoonn

If you are threatened in or near your vehicle, you can press for

1.5 seconds to trigger Panic Mode on your security system and

attract attention. The siren will sound and the parking lights will

flash for 30-seconds. To stop Panic Mode at any time, press

on the remote.

UUssiinngg YYoouurr SSyysstteemm

The remote buttons indicated in this manual correspond to a stan-

dard configuration remote, unless otherwise specified.

You can arm the security system by pressing for one second.

When the system arms, you will hear a short siren sound (chirp)

and the parking lights will flash once. If the power door locks are

controlled by the system, the doors will also lock. Once armed, the

LED system status indicator will flash once per second to indicate

that the system is actively protecting your vehicle. If you hear a

second chirp after arming and notice that the LED system status

indicator is flashing in a grouped pattern, this signals Bypass

Notification. Bypass Notification is described in detail in the

Diagnostics section of this manual.

Your security system can also be programmed for Passive Arming.

With Passive Arming, the system automatically arms itself 30 sec-

AUX

AArrmmiinngg

AUX

2004 Directed Electronics, Inc.

onds after the ignition has been turned off and the last door has

been closed. During the 30-second Passive Arming countdown, the

LED system status indicator will flash twice as fast as it does when

the system is armed. If the system is programmed for Passive

Arming, care must be taken to prevent the keys from being locked

in the vehicle.

NNOOTTEE::

If any protected entry point, such as a door or switch-protected

trunk or hood, is open, Passive Arming will not engage. Additionally, each

time a sensor is triggered during the Passive Arming countdown, the

countdown starts over.

Arming your security system protects your vehicle to the following

degrees:

■ Light impacts trigger a

wwaarrnn--aawwaayy

response, causing the siren

to chirp and the parking lights to flash for a few seconds.

■ Heavy impacts trip a

ttrriiggggeerr sseeqquueennccee

, which consists of the

siren sounding continuously and the parking lights flashing

for 30 seconds.

■ If a door is opened, the siren immediately starts chirping and

the parking lights start flashing to provide an instant

response. Three seconds later, the siren output changes to a

continuous blast. This two-stage

pprrooggrreessssiivvee rreessppoonnssee

allows

you time to disarm the security system with your remote, in

case the door is inadvertently opened while the system is

armed.

■ Turning on the ignition key triggers the same two-stage pro-

gressive response as opening a door.

■ The fault-proof starter interrupt prevents the vehicle’s starter

from cranking.

2004 Directed Electronics, Inc.

Press to disarm the security system when it is already armed.

If the power locks are controlled by the system, the doors will also

unlock. Disarming is confirmed when the parking lights flash twice

and the siren emits two chirps. The LED system status indicator will

also stop flashing. The siren chirping either four or five times when

disarming indicates Tamper Alert, which is described in the

Diagnostics section of this guide.

If your remote is lost or damaged, you can manually disarm your

vehicle security system. To disarm the system without a remote,

you must have the vehicle's ignition key and know where the

Valet® switch is located. Be sure to check with your installer at the

time of installation for the location of the Valet® switch.

To disarm the security system,

turn the ignition key on and

press the Valet® switch within

15 seconds. The system should

now disarm. If the system does not disarm, you may have waited

too long to press the Valet® switch; turn the ignition off and

repeat the process.

LLooccaattiioonn ooff VVaalleett®® SSwwiittcchh________________________________________________________________

DRW-35

DDiissaarrmmiinngg WWiitthhoouutt aa RReemmoottee

AUX

DDiissaarrmmiinngg

2004 Directed Electronics, Inc.

If you are threatened in or near your vehicle, you can press for

1.5 seconds to trigger Panic Mode on your security system and

attract attention. The siren will sound and the parking lights will

flash for 30 seconds. To stop the Panic Mode at any time, press

or again.

Use remote-controlled silent arm/disarm to temporarily turn off

the arm or disarm chirps by briefly pressing before either

arming or disarming. The confirmation chirp(s) will then be elimi-

nated for that one operation only. To permanently turn off the arm

and disarm chirps, contact your installation dealer.

NNOOTTEE::

The warn-away response to lighter impacts is bypassed if the

system is armed using remote-controlled silent arm/disarm. This ensures

that the siren does not chirp in an environment where you do not want

chirps to be emitted. The system is still capable of being triggered by

heavier impacts; only the warn-away response generated by light impacts

is bypassed.

Valet® Mode prevents your security system from arming and trig-

gering either automatically or with the remote. In Valet® Mode, the

system will not arm, but all convenience functions (door locks,

trunk release, etc.) remain operational. This feature is useful when

washing or servicing your vehicle. You can access Valet® Mode

either manually or from the remote.

To enter or exit Valet® Mode with the Valet® switch:

VVaalleett®® MMooddee

AUX

RReemmoottee--CCoonnttrroolllleedd SSiilleenntt AArrmm//DDiissaarrmm

AUX

PPaanniicc MMooddee

1100

2004 Directed Electronics, Inc.

1. Turn the ignition on.

2. Turn the ignition off.

3. Press and release the

Valet® switch within 10

seconds.

The LED system status indicator will light solidly if you are

entering Valet® Mode and will turn off if you are exiting Valet® Mode.

You can also enter or exit Valet® Mode by using the remote:

1. Open any vehicle door.

2. Press .

3. Press .

4. Press again.

The LED system status indicator will light solidly if you have entered

Valet® Mode and will turn off if you have exited Valet® Mode.

Your security system has Nuisance Prevention Circuitry

™

(NPC

™

) to

prevent annoying false alarms. This circuitry is designed to prevent

repetitive trigger sequences due to faulty door pinswitches or envi-

ronmental conditions such as thunder, jackhammers, airport

noise, etc.

Here's how it works: If the alarm is triggered by the same sensor

or switch three times within a 60 minute period, your system inter-

NNuuiissaannccee PPrreevveennttiioonn

®®

CCiirrccuuiittrryy

AUX

RReemmoottee--CCoonnttrroolllleedd VVaalleett®®

DRW-35

1111

2004 Directed Electronics, Inc.

prets this pattern of triggers as false alarms. After the third trig-

ger, the NPC

™

ignores, or bypasses, that sensor or switch (along

with any other sensors or switches sharing the same zone) for 60

minutes. If the bypassed sensor is triggered again while it is

already being bypassed, the 60-minute bypass period will start

over. This ensures that a sensor that is continually being triggered

will remain bypassed.

The vehicle doors are protected differently by NPC

™

. If your secu-

rity system is triggered by an open door for three, full 30-second

cycles (one and one half minutes), the system will bypass the

doors until the trigger ceases.

NNOOTTEE

: Arming and disarming the system does not reset the NPC

™

. The only

ways to reset a bypassed zone are for that zone not to be triggered for

60 minutes or to turn the ignition key on. When testing your system, it

is important to remember that NPC™ can cause zones to be bypassed and

appear to not work. If five chirps are heard when disarming the system,

NPC™ has been engaged. To clear the NPC™ memory, simply turn the igni-

tion key on.

DDiiaaggnnoossttiiccss

The microprocessor at the heart of your system has the ability to

constantly monitor all of the switches and sensors connected to it.

It can detect any faulty switches or sensors and prevent them from

disabling the entire system. It can also record and report any trig-

gers that occur when you are away from your vehicle.

1122

2004 Directed Electronics, Inc.

If the system is armed at the same time that an input is active

(door opening, sensor triggering, etc.), you will hear one chirp to

indicate arming and a second chirp a few seconds later to indicate

Bypass Notification. A Bypass Notification chirp means that the

system ignores the input that was active when the system was

armed, until that input ceases. Three seconds after that input

ceases, the system will resume normal monitoring. For example, if

your vehicle has an interior light exit delay and you arm the sys-

tem before the light turns off, you may hear a Bypass Notification

chirp. Three seconds after the light turns off, however, normal

monitoring resumes.

NNOOTTEE::

Bypass Notification does not occur when the system is in remote-

controlled silent arm/disarm mode or if the chirps have been programmed

not to sound.

Your system has a Tamper Alert feature that notifies you of system

triggers that occur while you are away from your vehicle. If you

hear four chirps when you disarm, this indicates that the system

was triggered in your absence. If you hear five chirps when you

disarm, this indicates that a specific zone was triggered so many

times that the NPC

™

has bypassed that zone. In both cases, the

pattern of the flashing LED system status indicator indicates which

zone was triggered (see Table of Zones). The LED does not, howev-

er, report when warn-away responses have activated; it only

reports triggered sequences. The system retains this information in

DDiissaarrmmiinngg DDiiaaggnnoossttiiccss

AArrmmiinngg DDiiaaggnnoossttiiccss

1133

2004 Directed Electronics, Inc.

its memory and will continue to chirp four or five times each time

the system is disarmed, until the next time the ignition is turned on.

A zone is represented by the number of LED flashes used by the

system to identify a particular type of input. Standard input assign-

ments are listed in the following table, along with spaces to write

in any optional sensors or switches that you have had installed.

ZZOONNEE

(Number of

DDEEAALLEERR--IINNSSTTAALLLLEEDD

LED Flashes)

DDEESSCCRRIIPPTTIIOONN OOPPTTIIOONNSS

Instant trigger for optional sensor,

hood or trunk pins

A heavier impact detected by

the on-board impact sensor

Door switch trigger

Ignition trigger

NNOOTTEE::

The LED does not report when the warn-away response has been

activated; it only reports triggered sequences.

TTaabbllee ooff ZZoonneess

1144

2004 Directed Electronics, Inc.

SStteeaalltthh CCooddiinngg

™

TTeecchhnnoollooggyy

The receiver and remote use mathematical formulas called algo-

rithms to change their codes each time the remote is used. This

Stealth Coding

™

Technology has been developed to increase the

security of the unit. By following this set code sequence, the

receiver and remote stay synchronized, even if the remote is used

out of range of the vehicle. If, however, the remote is pressed many

times out of range, or the battery is removed, the remote may get

temporarily out of sync and fail to operate the system. To resyn-

chronize the remote, simply press several times within range

of the vehicle. The system will automatically resynchronize and the

remote will respond normally.

HHiigghh FFrreeqquueennccyy

Your system transmits and receives at 434 MHz. This provides a

cleaner spectrum with less interference and a more stable signal.

Enjoy a phenomenal increase in range, even in areas with high

radio interference.

AUX

1155

2004 Directed Electronics, Inc.

PPrrooggrraammmmiinngg OOppttiioonnss

Programming options control your system's normal, operational

set-up. Most options do not require additional parts, but some may

require installation labor.

This system's programming options are listed below, with the fac-

tory default settings in

bboolldd

■

AAccttiivvee aarrmmiinngg

(only with the remote) or passive arming (automat-

ic arming 30 seconds after the last vehicle door is closed).

■

AAccttiivvee ddoooorr lloocckkiinngg

(only when arming with the remote) or

passive door locking (selectable only when Passive Arming

has been programmed).

■ Arming and disarming confirmation siren chirps can be pro-

grammed

oonn

or off.

■ Ignition controlled door lock feature,

oonn

or off. With this fea-

ture on, the doors will lock three seconds after the ignition

key is turned on, and unlock when the ignition is turned off.

The system also prevents the doors from locking when the

ignition is turned on while any vehicle door is open.

1166

2004 Directed Electronics, Inc.

SSeeccuurriittyy && CCoonnvveenniieennccee

EExxppaannssiioonnss

Listed below are some of the many expansion options available for

use with your system. Please consult your dealer for a detailed

explanation of all the available options.

AAuuddiioo SSeennssoorr::

Metal on glass, glass cracking, and breaking glass

produce distinctive acoustic signatures. The 506T audio sensor uses

a microphone to detect these sounds, and then analyzes them with

proprietary acoustic software to determine if the glass has been

tampered with or broken.

BBaacckkuupp BBaatttteerryy::

The 520T Backup Battery ensures that the system

stays armed, triggers the alarm and keeps the optional starter

interrupt active if main battery power is disconnected.

FFiieelldd DDiissttuurrbbaannccee SSeennssoorr::

An invisible dome of coverage is estab-

lished by the 508D "radar" sensor. Your security system will respond

to any intrusions into this field by initiating the triggered sequence.

PPoowweerr LLoocckkss::

This system offers lock outputs that can control most

manufacturers' power door lock systems. For other systems, addi-

tional parts may be required.

PPoowweerr TTrruunnkk RReelleeaasse

e::

The output of the system can operate

a factory power release for the vehicle's trunk or hatch. An option-

al relay is required. If the factory release is not power-activated,

AUX

Page is loading ...

Avital Automobile Alarm 740T User manual

Brand: Avital

Model: Automobile Alarm 740T

Category: Remote starters

Type: User manual

This manual is also suitable for

Download PDF

report

Avital Automobile Alarm 740T User manual

This manual is also suitable for

Avital Automobile Alarm 740T User manual

Related papers

Other documents