Pro-Ject Optical Box E Phono Amplifier User manual

Type
User manual
Home » Pro-Ject » Pro-Ject Optical Box E Phono Amplifier with ND Converter Instruction Manual
Pro-Ject Optical Box E Phono Amplifier with ND Converter
Pro-Ject Optical Box E Phono Amplifier with ND Converter
Instruction Manual
Manuals+ User Manuals Simplified.
Contents
1 Dear music lover,
2 Connectors
3 Input selector
4 Connecting the record player
5 Line level input
6 Sampling frequency
7 Connection to the amplifier (Sound Bar, AV receiver
etc.)
8 Mains power connection
9 Technical specifications Pro-Ject Optical Box E Phono
10 Service
11 Warranty
12 Copyright, trademarks
13 Documents / Resources
14 Related Posts
Dear music lover,
thank you for purchasing a Pro-Ject Audio phono amplifier with ND converter.
In order to achieve maximum performance and reliability you should study these instructions for use carefully.
Warning of o hazard for the user, the unit or possible misuse
Important notice
Connectors
Make all connections whilst the phono amplifier is disconnected from the power supply.
Toke core to connect the left and right channels correctly. The right channel is usually marked red, the left channel
block or white.
Do not connect the phono amplifiers output to o phono input (sometimes lobe/led gram, disc or RIM) on the
amplifier.
Never use any other power supply than the one supplied with the unit.
Input selector
Operating the push button Phono/ Line selects the inputs. “Phono” represents signal from Phono In RCA sockets.
“Line” activates line level input Line In (jock 3.5mm).
Connecting the record player
Input button set to “Phono”.
Connect the tonearm signal lead to the Phono In RCA sockets of the phono preamplifier. The earthing wire may
be connected to the screw terminal GND if you encounter hum problems when using the record player.
Line level input
Input button set to “Line”.
A line level signal source (e.g. tape deck or reel deck) con be connected to the unit using Line In socket.
Integrated A/D converter relay the signal to digital data using Optical Out.
Sampling frequency
A dip switch located on the bottom of the unit sets the ND converter output sampling rote to 96kHz or 48kHz.
The Switch set towards bock side (to the connectors) represent 48kHz. Some of the amplifiers (soundborsetc.)
cannot handle sampling frequency higher than 48Hz.
Connection to the amplifier (Sound Bar, AV receiver etc.)
The unit provides analogue and digital output connection.
Use the analogue Line Out output of the unit for connection to a line input (such as AUX, CD, Tuner, Tope or
Video) in your amplifier.
Alternatively the built in AD converter allows to relay signal from inputs (Phono or Line) in digital format out of the
unit using Optical Out digital output to the corresponding digital input of the amplifier or any Sound Bar, AV-
receiver etc.
Both outputs (analogue and digital) run simultaneously.
Mains power connection
Connect the low voltage plug from the power supply to the Power 18V socket of the phono amplifier before
connecting the power supply to the mains.
Technical specifications Pro-Ject Optical Box E Phono
Goin,MM: 34dB
SNR: 74dB
THD+N: 0,02%@ l kHz
RIM-equalisation curve accuracy: 20Hz – 20kHz / max. 0,SdB
AID converter: PCM 1808, 24bit/ 96kHz (switchable to 48kHz)
Outboard power supply: 18V/ 500mA DC, suitable for your country’s mains supply
Power consumption: 200mA DC
Dimensions W x H x D (D with sockets): 120 x 32 x l 00 (106)mm
Weight: 250g without power supply
Service
Should you encounter a problem which you ore not able to alleviate or identify despite the above information,
please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be
sent to the responsible distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use.
Modification or change to any part of the product by unauthorized persons; release the manufacturer from any
liability over and above the lawful rights of the customer.
Copyright, trademarks
Pro-Jed Audio Systems is a Registered Trademark of H. Lichtenberger.
This guide was produced by: Pro-Ject Audio Systems Copyright c 2017. All rights reserved.
The information was correct at the time of going to press. The manufacturer reserves the right to make changes
to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical
development.
© Pro-Ject Audio Systems ·
Pro-Ject Optical Box E Pho no (from S/ N l 7F01 l 039) · Revision 2017.8.15
Documents / Resources
Pro-Ject Optical Box E Phono Amplifier with ND Converter [pdf] Instruction Manual
Optical Box E Phono, Amplifier with ND Converter, Optical Box E Phono Amplifier with ND Con
verter, Optical Box E Phono Amplifier, Amplifier
Manuals+,
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Pro-Ject Optical Box E Phono Amplifier User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI