9.808-377.0 - B 08/22
Register
your product
www.kaercher.com/welcome
G 2900 E
1.107-414.0
Operator Manual
Gas Pressure Washer.................3
Manuel D'utilisation
Laveuse à pression à gaz...........19
Manual del operador
Hidrolavadora a presión de gas..........39
1 Handle
2 Spray gun
3 Spray gun safety lock
4 High pressure hose
5 Spray wand
6 Quick connect nozzles
7 Knob
8 Fuel Tank
9 Oil Dipstick
MODEL OVERVIEW
10 Water inlet for garden hose
11 High pressure outlet
12 Spark plug
13 Water inlet lter (installed in pump)
14 On/Off Switch
15 Strap
*For engine details see engine manual.
2
7
9
6
12
8
4
12
11
13
10 5
14
3
15
3
Model Overview 2
Important Safety Instructions 5
Assembly Instructions 7
Operating Instructions 9
Using the Accessories 10
Working With Detergents 11
Taking a Break 12
Shutting Down & Clean-Up 12
Winterizing and Long-Term Storage 12
Maintenance Instructions 13
Cleaning Tips 13
Troubleshooting 15
Warranty Information 17
Specications
HIGH PRESSURE WASHER OPERATOR MANUAL
G 2900 E
Max Pressure 2900 PSI
Max Water Flow 2.6 GPM
Detergent Suction 0.04 GPM
Engine Karcher KPS 196cc
Fuel Type Unleaded Gasoline
Fuel Tank Size 0.8 gal
Engine Oil Type SAE 10W-30
Engine Oil Capacity 0.15 gal
Part No. 1.107-414.0
Nozzle - Yellow, 15 deg
Nozzle - Green, 25 deg
Nozzle - White, 40 deg
Nozzle - Black, 60 deg
2900 PSI at 2.4 GPM
2700 PSI at 2.5 GPM
2300 PSI at 2.6 GPM
400 PSI at 2.8 GPM
Nozzle kit Part No. 8.758-924.0
This high-pressure cleaner is designed:
- To clean machines, vehicles, buildings, tools,
facades, decks, patios, driveways, walkways, gar-
den equipment etc. (detergents may be required
in some cleaning scenarios).
- To be used with accessories, replacement parts
and detergents approved by KÄRCHER. Observe
the instructions provided with these detergents.
Proper Use
The packing material can be recycled.
Please do not place the packaging into
the ordinary refuse for disposal, but ar-
range for the proper recycling.
Old appliances contain valuable materials
than can be recycled. Please arrange for
the proper recycling of old appliances.
Please dispose your old appliances using
appropriate collection systems.
Notes About the ingredients (REACH)
You will nd current information about the ingre-
dients at:
https://www.kaercher.com/int/inside-kaercher/
sustainability/supply-chain-and-products.html
Owner/User Responsibility
DANGER
Indication of an imminent threat of danger that will
lead to severe injuries or even death.
WARNING
Indication of a potentially dangerous situation that
may lead to severe injuries or even death.
CAUTION
Indication of a potentially dangerous situation that
may lead to minor injuries.
ATTENTION
Indication of a potentially dangerous situation that
may lead to damage to property.
Safety Alert Symbols
4
The owner and/or user must have an understand-
ing of the manufacturer’s operating instructions
and warnings before using this pressure washer.
Warning information should be emphasized and
understood. If the operator is not uent in English,
the manufacturer’s instructions and warnings shall
be read to and discussed with the operator in
the operator’s native language by the purchaser/
owner, making sure that the operator comprehends
its contents. Owner and/or user must study and
maintain for future reference the manufacturer’s
instructions.
Owner/User Responsibility
HIGH PRESSURE WASHER OPERATOR MANUAL
You can contact our Customer Service department
by phone at 1-800-537-4129 or via the website at
www.karcher.com/us.
Your device must be registered in order to help
with any questions or issues that you have. You
can register your device at www.karcher-register.
com if located in the U.S.A., www.karcher.com/
ca if located in Canada, or www.karcher.com/mx
if located in Mexico.
In the case of a warranty claim, you can contact
customer support. Please see the contact informa-
tion listed below for either the USA, Canada, or
Mexico. You MUST provide your proof of purchase
in order to le a warranty claim either via email,
phone, or fax.
USA Customer Service
Registration
Warranty
You can contact our Customer Service department
by phone at 1-800-465-4980 or via the website at
www.karcher.com/ca.
Canada Customer Service
You can contact our Customer Service department
by phone at 01-800-024-13-13 or via the website
at www.karcher.com/mx.
Mexico Customer Service
The operator must know how to stop the pressure
washer quickly, and understand the operations of
all controls.
This manual should be considered a permanent
part of this pressure washer and should remain
with it if resold.
Read engine manual (which is separate from this
manual) before starting.
SAVE THESE INSTRUCTIONS
Save These Instructions
Read Engine Manual
CUSTOMER SERVICE
5
IMPORTANT SAFETY INSTRUCTIONS
▄ Read all instructions before using product.
▄ To reduce the risk of injury, close supervision
is necessary when a product is used near
children.
▄ High pressure cleaners shall not be used by
children or untrained personnel.
▄ Know how to stop the product and bleed pres-
sures quickly. Be thoroughly familiar with the
controls.
▄ Stay alert - watch what you are doing.
▄ Do not operate when fatigued or under the
inuence of alcohol or drugs.
▄ Keep operating area clear of all persons.
▄ Do not overreach or stand on unstable sup-
port. Keep good footing and balance at all
times.
▄ Follow the maintenance instructions specied
in the manual.
▄ To avoid risks, all repairs and replacement of
should only be carried out by trained person-
nel.
Read the operating instructions of the
engine manufacturer before start-up and
follow the safety instructions carefully.
WARNING
When using this product, basic precautions
should always be followed, including the fo-
llowing:
▄ High pressure hoses, fittings and cou-
plings are important for the safety of the
machine. Use only hoses, ttings and cou-
plings recommended by the manufacturer.
WARNING
Risk of injection or injury, do not direct
discharge stream at persons or animals.
▄ High pressure jets can be dangerous if mis-
used. The jet must not be directed at persons,
animals, electrical devices, or the unit itself.
▄ Do not direct the jet against yourself or others
in order to clean clothes or foot-wear.
▄ Do not use the machine within range of
persons unless they wear protective
clothing.
▄ To ensure machine safety, use only original
spare parts from the manufacturer or
approved by the manufacturer.
DANGER
Do not spray electrical connections, electrical
outlets or xtures.
WARNING
Risk of explosion, do not spray ammable
liquids. Operate only where open ame or
torch is permitted.
▄ Do not use acids, solvents, or any alkaline
or ammable material in this product. These
products can cause physical injuries to the
operator and irreversible damage to the
machine.
6
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
Gun kicks back - hold with both hands.
▄ The trigger gun safety lock prevents the
trigger from accidentally being engaged.
This safety feature must be engaged when
replacing nozzles or not in use.
WARNING
▄ Risk of asphyxiation: use this product only in
a well ventilated area.
▄ Ensure that any exhaust emissions are not
in the vicinity of air intakes.
▄ Operate and fuel machine in a well ventilated
area, free of devices featuring an open pilot
or ame such as boilers, water heaters, etc.
▄ Running this product indoors can result in
death due to carbon monoxide, a poisonous
gas you cannot see or smell. Never operate
indoors, even if windows and doors are open.
Only use outdoor and far away from windows,
doors, and openings or vents.
▄ During use of high pressure cleaners,
aerosols may be formed. Inhalation of
aerosols can be hazardous to health.
▄ Do not use the machine if a supply cord or
important parts of the machine are
damaged, e.g. safety devices, high
pressure hoses, trigger gun.
WARNING
Incorrect fuels shall not be used as they may
prove hazardous.
WARNING
Always switch off the On/Off switch when
leaving the machine unattended.
WARNING
Risk of re, do not add fuel when the product
is operating or still hot.
CAUTION
▄ Do not operate if fuel has been spilled. In-
stead, move machine to different location and
avoid creating sparks.
▄ This machine has hot surfaces which can
cause burns. Operate in a safe environment
and away from children.
▄ Do not touch hot surfaces or allow acces-
sories to contact hot surfaces.
▄ Do not leave machine running unattended.
▄ Avoid tipping machine on its side.
WARNING
Serious injury can result from high pressure
discharge produced by pressure washers.
Keep out of reach of children.
WARNING PROP 65
This product can expose you to chemicals
including Lead and Diisononyl Phthalate,
which are known to the State of California to
cause cancer, birth defects or other reproduc-
tive harm. For more information, go to www.
P65Warnings.ca.gov
Wash hands after handling.
SAVE THESE INSTRUCTIONS
7
WATER SUPPLY (Cold Water Only)
WARNING
Water that has owed through backow
preventers is considered to be non potable.
Use a water lter to avoid potential damage
from dirt in the water supply.
▄ Garden hose must be at least 5/8 inch inside
diameter.
▄ Flow rate of water supply must not fall below
2.64 GPM (Gallons per minute) (10 L/Min
(Liters per minute)).
▄ Flow rate can be determined by running the
water for one minute into an empty 5 Gallon
bucket (20 Liter container).
▄ Supply water pressure must be greater than
40 PSI.
▄ The water supply temperature must not ex-
ceed 104°F/40°C.
▄ Never use the pressure washer to draw in
water contaminated with solvents, e.g. paint
thinners, fuel, oil, etc.
▄ Always prevent debris from being drawn into
the unit by using a clean water source. Use
additional water lter.
▄ Do not operate pressure washer without the
water turned on.
Hardware (included)
ASSEMBLY INSTRUCTIONS
Description Purpose Illustration Qty
AHexagonal 1/4"
bolt Handle assembly 2
BKnob Handle assembly 2
CQuick connect
nozzle kit
Nozzle kit
assembly 1
DSpray wand Spray gun assembly 1
ESpray Gun Spray gun
assembly 1
FHigh pressure
hose
Spray gun
assembly 1
GDetergent
siphon hose Detergent mode 1
IMPORTANT SAFETY INSTRUCTIONS
8
ASSEMBLY INSTRUCTIONS
Assembling
4 5 6
1 2 3
B
A
C
E
D
Illustration 1:
Attach the handle to the pressure washer
frame.
Illustration 2:
Align holes, insert bolts (A), and tighten with
knobs (B).
Illustration 3:
Place the quick connect nozzles (C) in the
nozzle holder.
Illustration 4,5:
Attach the wand (D) to the spray gun (E).
Push the wand (D) into the trigger gun (E) and
then thread the connection.
Illustration 6:
Remove the cap / dipstick from the oil
level and add the oil.
Assembling
9
Be sure the machine is level when checking
the oil level. (Refer to the engines operating
manual for seasonal grades).
STEP 4:
Fill gasoline tank with unleaded gasoline.
Do not use leaded gasoline. Cosult engine
manual for appropriate octane rating
Do not add oil to the gasoline.
STEP 5:
Connect the high pressure hose to the high
pressure outlet on the pump.
WARNING
High pressure hoses, ttings and couplings
are important for the safety of the appliance.
Use only hoses, ttings and couplings recom-
mended by the manufacturer.
STEP 6:
Connect garden hose to unit's water inlet.
STEP 7:
Connect garden hose to the cold water source
and turn water completely on.
Do not use hot water. (Water supply tem-
perature must not exceed 104°F/40°C).
MAX
OIL FILLER CAP / DIPSTICK
MIN
STEP 1:
Pull the spring-loaded collar of the wand back
to insert your choice of quick connect nozzle.
Release the collar and push the nozzle until-
the collar clicks.
CAUTION
High pressure in nozzle area.
Risk of injury caused by improperly locked
nozzle.
▄ Make sure you hear a "click" when inserting
the nozzle tip into the wand.
▄ Pull the nozzle to make sure it is seated
properly before operating your unit.
STEP 2:
Attach the high pressure hose to the trigger
gun. Make sure to screw the hose all the way
into the trigger gun.
CAUTION
Engine shipped without oil. Before starting
engine, ll with oil. Do not over-ll. Do not run
the engine with a high or low oil level as this
can cause engine damage.
If you have further questions regarding the
engine, please refer to the engine manual
included with the unit.
STEP 3:
Check oil level. Oil level should always be
between the "MAX" and "MIN" marks on the
dipstick as shown in the picture below.
OPERATING INSTRUCTIONS
10
OPERATING INSTRUCTIONS
STEP 8:
Unlock the trigger gun safety lock. Pull Trigger
gun to eliminate trapped air, wait for a steady
ow of water to emerge from the spray nozzle.
STEP 9:
Turn On/Off switch to ON position.
ON
OFF
USING THE ACCESSORIES
15° spray angle = Yellow nozzle
For dirt accumulation over a surface.
Quick connect nozzles
The color-coded quick connect nozzles provide a
wide array of spray widths from 15° to 65° and are
easily accessible when placed in the convenient
nozzle holder.
25° spray angle = Green nozzle
For dirt accumulation over a large surface.
65° spray angle = Black nozzle
For operating with detergents or cleaning with
low pressure.
CAUTION
High pressure in nozzle area. Risk of injury
caused by improperly locked nozzle.
▄ Make sure you hear the "click" when inserting
the nozzle tip into the quick connection.
▄ Pull the nozzle to make sure it is seated
properly before operating your unit. (See
OPERATING INSTRUCTIONS: Step 1)
WARNING
To avoid serious injury never point spray
nozzle at yourself, other persons, or animals.
40° spray angle = White nozzle
For moderate dirt accumulation over a large
surface.
STEP 10:
Pull the starter handle. If the engine fails to
start after 3 pulls, squeeze the trigger gun to
release pressure, and repeat step.
WARNING
Starter cord kickback (rapid retraction) can
result in bodily injury. Kickback will pull hand
and arm toward engine faster than you can
let go. ALWAYS relieve spray gun pressure
before pulling starter cord. Pull starter cord
slowly until resistance is felt, then pull rapidly.
For engine details see engine manual.
11
Detergents can only be applied with the black
detergent nozzle.
STEP 1:
Install the black detergent nozzle for deter-
gent application at low pressure.
STEP 2:
Fill a container with Kärcher detergent diluted
according to the manufacturer's instructions.
Place the lter end of the detergent suction
tube into the container.
WORKING WITH DETERGENTS
STEP 3:
With the engine running, pull trigger to operate
unit.
Liquid detergent is drawn into the unit and
mixed with water.
Apply detergent to work area.
Do not allow detergent to dry on surface.
STEP 4:
Always draw fresh water through the deter-
gent suction tube when the cleaning job is
done, to rinse/ush any remaining detergents
from the injection system.
See Cleaning Tips for specic information on
how to clean different surfaces.
CAUTION
Never use:
– Bleach, chlorine products or other corrosive
chemicals
– Liquids containing solvents (i.e., paint thin-
ners, fuel, oils.)
– Tri-sodium phosphate products
– Ammonia products
– Acid-based products
WARNING
The use of these chemical, when used with high
pressure cleaners, can turn into an aerosol. Inhala-
tion of chemicals that have been aerosolized can
be hazardous to health.
These chemicals will harm the unit and damage
the surface being cleaned.
Use of these items will void the warranty.
Detergents
CAUTION
This unit has been designed for use with cleaning
detergents recommended by the manufacturer.
The use of other cleaning detergent may affect the
operation of the machine and void the warranty.
Always Use Kärcher Detergent for Best Results
Kärcher biodegradable detergents are specially
formulated to protect the environment and your
pressure washer. The special formula won't clog
the suction tube lter and will protect the internal
parts of the pressure washer for a longer life. For
Kärcher Detergents, check your retailer or visit
our website:
karcher.com/us or karcher.com/ca
12
STEP 6:
Screw bottle into water inlet on pressure
washer pump and squeeze until uid starts
to exit tue pump
STEP 6:
Disconnect the garden hose from the water
inlet on the unit.
STEP 7:
Disconnect the high pressure hose from the
high pressure outlet. Store the high pressure
hose in the hose holder strap.
STEP 1:
If detergents have been used, insert suction
tube into 0.5 gallons (1.8 L) of fresh water.
Install the black detergent nozzle and siphon
water at low pressure for one minute to clean
any detergent residue in the system.
STEP 2:
Move the engine On/Off switch to the OFF
position.
STEP 3:
Turn off the water source.
STEP 4:
Press trigger to release water pressure.
STEP 5:
Release trigger and engage gun safety lock.
SHUTTING DOWN & CLEAN-UP
WINTERIZING AND LONG-TERM STORAGE
CAUTION
Failure to follow the above directions may
result in damage to the pump assembly and
accessories and void the warranty.
It is highly recommended to use Kärcher's
Pump Guard (part number 9.558-998.0 sold
separately) before winter storage and during
the cleaning season to protect the pump from
freezing and premature wear.
STEP 1:
Move engine On/Off switch to OFF position.
STEP 2:
Disconnect all hoses.
STEP 3:
Unscrew cap from Pump Guard bottle.
STEP 4:
Remove internal seal.
STEP 5:
Reattach cap to Pump Guard bottle and
remove black protective cap.
STEP 7:
Pull starter handle until uid starts to exit the
pump's high pressure outlet
STEP 8:
Unscrew bottle. Store or dispose properly.
STEP 1:
Move the engine On/Off switch to the
OFF position.
STEP 2:
Release trigger and engage safety lock.
TAKING A BREAK ...ve minutes or more
13
CLEANING TIPS
(With or without detergent). Pre-rinse deck and
surrounding area with fresh water. If using Kärcher
Multi-Purpose Cleaner (part number 9.558-144.0 ,
sold separately), apply to surface at low pressure.
For best results, limit your work area to smaller sec-
tions of approximately 25ft² (2.3m²). Allow Kärcher
Multi-Purpose Cleaner to remain on surface 1-3
minutes. Do not allow detergent to dry on surface.
Using the white 40 degree nozzle, rinse at high
pressure in a long sweeping motion keeping the
spray nozzle approximately 35 inches (90 cm) and
slowly approach the surface until desired results
are achieved. Make sure you are not causing any
surface damage before cleaning the rest of the
deck. Always clean from top to bottom and left to
right. When moving on to a new section of the
cleaning surface, be sure to overlap the previous
section to eliminate stop marks and ensure a more
even cleaning result. For more information, go to
https://www.kaercher.com/int/home-garden/
know-how/cleaning-wooden-decking.html
(With or without detergent). Pre-rinse cleaning sur-
face with fresh water. If using Kärcher Multi-Purpose
Cleaner (part number 9.558-144.0, sold separately),
apply to surface at low pressure (for best results,
limit your work area to sections of approximately 6
ft. (1.8m) and always apply detergent from bottom
to top). Allow detergent to remain on surface 1-3
minutes. Do not allow detergent to dry on surface,
if surface appears to be drying, simply wet down
surface with fresh water. If needed, use special wash
brush attachment (part number 8.923-682.0 Rotating
Wash Brush, sold separately) to remove stubborn
Deck Cleaning
House Siding
(With or without detergent). Pre-rinse vehicle
with fresh water. If using Kärcher Vehicle Wash
and Wax (part number 9.558-946.0, sold sepa-
rately), apply to surface at low pressure. For best
results, clean one side of vehicle at a time and
always apply detergent from bottom to top, do not
Cars, Boats & Motorcycles
Initial Use
All pumps ship with oil already inside direct from
the factory. There is no need to add oil.
Pump Inspection
You should routinely make a visual inspection of
the pressure washer’s pump. If you notice oil leak-
ing around the pump seals, you should take the
pressure washer to a Kärcher-Authorized Service
Center for repair. (You can locate a service center
in your area online at: https://www.kaercher.
com/us/nd-a-dealer.html if located in the US or
https://www.kaercher.com/ca/support/services/
home-and-garden.html if located in Canada.
Pump Maintenance
The pump on your Kärcher pressure washer does
not require maintenance. Any attempts to service
or alter the pump may damage your pressure
washer and void your product warranty.
Carry out maintenance tasks for the engine accord-
ing to the specications provided in the operating
instructions provided by engine manufacturer.
Pump
Engine
MAINTENANCE INSTRUCTIONS
allow detergent to dry on surface. If needed, use
special wash brush attachment (not included) to
remove stubborn dirt. Using the white 40 degree
nozzle, rinse at high pressure in a long sweeping
motion keeping the spray nozzle approximately 35
inches (90 cm) and slowly approach the surface at
no more of 25 in (60 cm) until desired results are
achieved (distance should increase when rinsing
pin-striping or other sensitive surfaces). Always
clean from top to bottom and from left to right. For
best results, wipe surface dry with a chamois or
soft dry cloth. For more information, go to https://
www.kaercher.com/int/home-garden/know-
how/car-care.html and https://www.kaercher.
com/int/home-garden/know-how/motorcycle-
cleaning.html
14
CLEANING TIPS
(With or without detergent). Pre-rinse cleaning
surface with fresh water. If using Kärcher Multi-
Purpose Cleaner (part number 9.558-144.0, sold
separately), apply detergent at low pressure.
Allow Kärcher Multi-Purpose Cleaner to remain
on surface 1-3 minutes. Do not allow detergent
to dry on surface. Using the white 40 degree
nozzle, rinse at high pressure in a long sweeping
motion keeping the spray nozzle approximately 35
inches (90 cm) and slowly approach the surface
until desired results are achieved. For removing
extremely stubborn dirt, it may be necessary to
move the spray nozzle even closer to the surface
for greater dirt cutting action, make sure you are
not causing any surface damage.
Barbecue Grills, Outdoor Power
Equipment & Gardening Tools
(With or without detergent). Pre-rinse furniture
and surrounding area with fresh water. If using
Kärcher Multi-Purpose Cleaner apply to surface
at low pressure. Allow Kärcher Multi-Purpose
Cleaner to remain on surface 1-3 minutes. Do not
allow detergent to dry on surface. If needed use
special Wash Brush Attachment (part number
8.923-682.0 Rotating Wash Brush, sold separately)
to remove stubborn dirt. Using the white 25 degree
nozzle, rinse at high pressure in a long sweeping
motion keeping the spray nozzle approximately 25
inches (60 cm) and slowly approach the surface
until desired results are achieved. Make sure
you are not causing any surface damage before
cleaning the rest of the surface. For best results,
clean from top to bottom and from left to right. For
more information, go to https://www.kaercher.
com/us/home-garden/application-tips/garden-
furniture-cleaning.html
Patio & Lawn Furniture
▄ Before cleaning any surface, test spray pa-
ttern and distance in an inconspicuous area.
▄ If painted surfaces are peeling or chipping,
use extreme caution as pressure washer may
remove the loose paint from the surface.
▄ When using on surfaces which might come in
contact with food, ush surfaces with plenty
of drinking water.
▄ For additional cleaning tips, visit our website
at karcher.com/us or karcher.com/ca
Recommendations
Optional accessories are available to further
enhance your cleaning capabilities. These acces-
sories are accurate as of the printing date of this
manual. Please check our website:
karcher.com/us or karcher.com/ca for pricing
and up-to-date information.
– Extension Hose
– Turbo Nozzle
– 15" Surface Cleaner
Optional Accessories
(With or without detergent). Pre-rinse cleaning
surface with fresh water. If using Kärcher Multi-
Purpose Cleaner (part number 9.558-144.0, sold
separately) apply to surface at low pressure. For
best results, limit your work area to smaller sec-
tions of approximately 25ft² (2.3m²). Allow Kärcher
Multi-Purpose Cleaner to remain on surface 1-3
minutes. Do not allow detergent to dry on surface.
Using the white 25 degree nozzle, rinse at high
pressure in a long sweeping motion keeping the
spray nozzle approximately 25 inches (60 cm) and
slowly approach the surface until desired results
are achieved. Make sure you are not causing
any surface damage before cleaning the rest of
the surface. Always clean from top to bottom and
left to right. Always clean from top to bottom and
from left to right. For removing extremely stubborn
stains, use a Turbo Nozzle Spray Nozzle (part
number 8.641-034.0, sold separately). For more
information, go to https://www.kaercher.com/
us/home-garden/application-tips/mossy-brick-
and-stone.html
Cemented Patios, Brick and Stone
dirt. Using the white 40 degree nozzle, rinse at high
pressure in a long sweeping motion keeping the
spray nozzle approximately 35 inches (90 cm) and
slowly approach the surface until desired results are
achieved. Make sure you are not causing any surface
damage before cleaning the rest of the deck.
15
CAUTION
Remove the spark plug cable to prevent accidental
ignition of the engine before making any repair.
TROUBLESHOOTING
Symptom Cause Solution
ENGINE WILL
NOT START
No gasoline Fill gasoline tank
Engine switch OFF Turn engine switch to the ON position
Water pressure built up in
the machine
Squeeze the trigger to release the pressure
For additional engine problems refer to the engine manual.
NOT ENOUGH
PRESSURE
Diameter of garden hose is
too small
Replace with a 5/8” inside diameter or larger
garden hose
Water supply is restricted Check garden hose for kinks, leaks or
blockage
Not enough inlet water
supply
Turn water on full force. Check garden hose
for kinks, leaks or blockage.
Water inlet lter is clogged Remove lter and rinse out in warm water
Black detergent nozzle is
attached
Remove black detergent nozzle and attach
high pressure nozzle
OUTPUT PRES-
SURE
VARIES HIGH AND
LOW
Not enough inlet water
supply.
Turn water on full force. Check garden hose
for kinks, leaks or blockage
Pump is sucking air Check that hoses and ttings are air tight.
Turn off machine and purge pump by
squeezing trigger gun until a steady ow of
water emerges through the nozzle
Water inlet lter is clogged Remove lter and rinse out in warm water
Spray nozzle is obstructed Blow out or remove debris with a ne needle
Calcied gun, hose or
spray wand
Run distilled vinegar through detergent
suction tube.
NO DETERGENT Detergent suction tube not
properly connected to the
machine
Check connection
Detergent suction tube
folded
With machine and water turned off, detach
suction tube to help unfold and reattach.
Detergent is too thick Dilute detergent, for best results use Kärcher
detergent
16
If the symptom you are experiencing is not listed
above, or if the provided solutions do not solve your
issue, please visit our extensive online trouble-
shooting database at:
www.karcher-help.com or www.karcher.com/
ca/support/faqs.html
Symptom Cause Solution
NO DETERGENT Filter on detergent suction
tube is clogged
Run warm water through lter to remove
debris
Damaged or clogged deter-
gent suction tube
Remove obstruction or replace detergent
suction tube
A high pressure nozzle is
attached
Replace with black detergent nozzle
Spray nozzle is obstructed Blow out or remove debris with ne needle
GARDEN HOSE
CONNECTION
LEAKS
Loose ttings Tighten ttings
Missing/worn rubber
washer
Insert new washer
SPRAY WAND
LEAKS
Spray wand not properly
attached
Turn the swivel nut of the gun clockwise until
connection is tight
Broken o-ring or plastic
insert
Call listed support phone numbers in Cus-
tomer Service section.
Visit www.karcher-help.com or locate a ser-
vice center at www.karcher.com/us or www.
karcher.com/ca
PUMP IS NOISY Not enough water supply Check that hoses and ttings are air tight.
Turn off machine and purge pump by
squeezing trigger gun until a steady ow of
water emerges through the nozzle
WATER LEAKS
FROM PUMP (UP
TO 10 DROP PER
MINUTE IS PER-
MISSIBLE)
Loose ttings Check ttings
Water seals are damaged
or worn.
Visit www.karcher-help.com or locate a ser-
vice center at www.karcher.com/us or www.
karcher.com/ca
Thermal protection device
is activated.
Thermal protection device will auto reset.
Do not run pump for more than 5 minutes
without spraying
OIL DRIP Oil seals are damaged or
worn
Visit www.karcher-help.com or locate a ser-
vice center at www.karcher.com/us or www.
karcher.com/ca
TROUBLESHOOTING
17
High Pressure Washers
3 Year Limited warranty
This Kärcher product is warranted by Kärcher to be free of defects in workmanship and
materials under normal use.
Specic warranty applies to:
• Kärcher KPS and KXS series engines are warranted for three (3) years parts and labor and
serviced by a Kärcher service center
• Honda GX series engines are warranted for three (3) years parts and labor and serviced
by a Honda authorized service center
• Pumps are warranted for three (3) years parts and labor and are serviced by a Kärcher
service center
• Frames, handles and detergent tanks, and other structural components, carry a three (3)
year parts and labor warranty.
• Standard accessories and attachments are warranted for a ninety (90) day period.
• Any commercial, industrial or rental use of this equipment will VOID the warranty.
The warranty period is calculated from the date of purchase by the end user and covers
the cost for replacement parts and/or equipment and warranty labor performed. In order to
verify a warranty situation, the machine must be evaluated by an Authorized Kärcher Service
Center or by an authorized service center representing the engine manufacturer. A copy of
the original purchase receipt or gift receipt from the original retailer must also accompany
the warranty claim. To locate the nearest authorized Kärcher service center, please visit our
website at www.karcher-help.com or www.karcher.com/ca/support/faqs.html
Your device must be registered in order to help with any questions or issues that you have.
You can register your device at www.karcher-register.com.
Kärcher’s obligation under this warranty shall strictly be limited, at Kärcher’s option, either to
replace or repair, through Kärcher direct or through an Authorized Kärcher Service Dealer
without charge during the warranty period any part, which in the opinion of the manufacturer,
shows defect in workmanship or material. Service will be scheduled according to the normal
work ow and business hours at the service center, and availability of replacement parts. All
decisions of Kärcher with regard to this limited warranty shall be nal.
This warranty does not cover:
• Merchandise sold as reconditioned, used, demonstration or oor models.
• Merchandise purchased on eBay and other online auction web sites.
• Damage caused by misuse, neglect, accident, abuse, improper handling, freezing, normal
wear and tear or non-compliance with operator’s manual.
• Damage caused by water sediment, contaminated water supply or use of chemicals and
detergents not approved by or recommended by Kärcher.
WARRANTY INFORMATION
18
• Damage caused by acts of nature such as oods, res, earthquakes, lightning strikes, etc.
• Devices or accessories not distributed or approved by Kärcher. Any use of such said devices
or accessories will void implied warranty.
• Repairs made by the end user or any service center not authorized by Kärcher. Any such
tampering with Kärcher equipment or accessories will void the implied warranty.
• Any cost for shipping by the customer or authorized service center of the alleged defective
part or equipment.
This warranty is non-transferable and applies only to products purchased through a Kärcher
authorized reseller in the United States and Canada . Equipment provided, but not manu-
factured by Kärcher such as Honda and Kohler petrol engines are subject to warranties and
service through said manufacturer’s service centers according to the terms and conditions
provided by the respective original equipment manufacturer. Kärcher is not authorized and
has no responsibility to provide warranty service for Honda. This warranty gives you specic
legal rights. You may have other rights, which vary by country and state/province.
Please register online at www.karcher-register.com
Online registration is quick, free and provides you with a conrmation
email for your records.
WARRANTY INFORMATION
1 Poignée
2 Pistolet
3 Verrou de sécurité du pistolet
4 Boyau haute pression
5 Tube de vaporisation
6 Buses à raccord rapide
7 Bouton
8 Réservoir de carburant
9 Jauge d'huile
APERÇU DU MODÈLE
10 Entrée d'eau pour le boyau d'arrosage
11 Sortie haute pression
12 Bougie d'allumage
13 Filtre d'entrée d'eau (installé dans la pompe)
14 Interrupteur Marche/Arrêt
15 Sangle
*Voir le manuel du moteur pour les détails du moteur pour les
détails du moteur
19
7
9
6
12
8
4
12
11
13
10 5
14
3
15
20
Aperçu du modèle 19
Importantes Consignes De Sécurité 22
Directives d'assemblage 24
Instructions de fonctionnement 26
Utilisation des accessoires 28
Utilisation de détergents 28
Prendre une pause 29
Mise hors tension et nettoyage 30
Entreposage à long terme et 30
pour l'hiver
Instructions d'entretien 31
Conseils sur le nettoyage 31
Dépannage 34
Information sur la garantie 37
MANUEL DE L'UTILISATEUR DE LA MACHINE À LAVER À HAUTE PRESSION
Spécications
G 2900 E
Pression maximale 2900 PSI
Débit d'eau maximum 2.6 GPM
Aspiration de
détergent 0.04 GPM
Moteur Karcher KPS 196cc
Type de carburant Essence sans plomb
Plein format du
réservoir 0.8 gal
Type d'huile à
moteur SAE 10W-30
Capacité en huile
du moteur 0.15 gal
No de pièce 1.107-414.0
Buse - Jaune, 15 deg
Buse - Verte, 25 deg
Buse - Blanche, 40 deg
Buse - Noir, 60 deg
2900 PSI at 2.4 GPM
2700 PSI at 2.5 GPM
2300 PSI at 2.6 GPM
400 PSI at 2.8 GPM
Kit de buses Réf. 8.758-924.0
Ce nettoyeur à haute pression est conçu pour:
- Nettoyer les machines, les véhicules, les bâti-
ments, les outils, les façades, les terrasses, les
patios, les entrées, les allées, les équipements de
jardin, etc. (des détergents peuvent être néces-
saires dans certains cas).
- À utiliser avec les accessoires, les pièces
de rechange et les détergents approuvés par
KÄRCHER. Veuillez observer les instructions
fournies avec ces détergents.
Utilisation appropriée
Le matériel d'emballage peut être
recyclé.
Veuillez ne pas jeter l'emballage dans
les ordures ménagères, mais prendre les dispo-
sitions nécessaires pour le recycler.
Les vieux appareils contiennent des
matériaux précieux qui peuvent être
recyclés. Veuillez prendre des disposi-
tions pour le recyclage approprié des
vieux appareils. Veuillez vous débarrasser de
vos vieux appareils en utilisant les systèmes de
collecte appropriés.
Remarque concernant les ingrédients (REACH)
Vous trouverez des informations actuelles sur
les ingrédients au:
https://www.kaercher.com/int/inside-kaercher/
sustainability/supply-chain-and-products.html
Responsabilités du
propriétaire/utilisateur
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
