M-system 48V User manual

Brand: M-system

Model: 48V

Type: User manual

48V

P. 1 / 4

EM-9311 Rev.5

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

contents of package you received as outlined below.

If you have any problems or questions on the product, please

contact M-System’s Sales Ofﬁce or representatives.

n PACKAGE INCLUDES:

Bargraph indicator ...................................................... (1)

n MODEL NO.

Check that model No. described on the speciﬁcation label is

exactly what you ordered.

n INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation and connection.

POINTS OF CAUTION

n POWER INPUT RATINGS

• Operational range & power consumption: Check the power

rating for the unit on the speciﬁcation label.

AC Ratings

Rating 85 – 132V AC: 85 – 132V, 47 –63 Hz

Rating 170 – 264V AC: 170 – 264V, 47 –63 Hz

Approx. 3.5VA (48V-1) or 5.5VA (48V-2)

DC Rating

Rating 24V DC: 24V ±15%,

approx. 2W (48V-1) or 4W (48V-2)

n INSTALLATION

• A bezel is provided in the pocket inside the package.

Push the bezel in behind the front side of the unit as illus-

trated below.

• When installing the meter into a panel, rst remove the

nameplates at the top and bottom of the front panel. Turn the

screws behind these nameplates clockwise until the retaining

clips come up and are ﬁxed.

Turning the screws counterclockwise loosen the retaining clips.

• The acrylic front cover and scaleplate can be removed when

you remove the nameplates.

n ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing and ventilate it.

• Do not install the unit where it is subjected to continuous

vibration. Do not apply physical impact to the unit.

• Environmental temperature must be within 0 to 50°C (32 to

122°F) with relative humidity within 40 to 80% RH in order

to ensure adequate life span and operation.

• Be sure that the ventilation slits are not covered with cables,

etc. With the vertical mounting, leave at least 5 cm (2 in.) both

at the top and bottom of the unit; with the horizontal mount-

ing, leave at least 2.5 cm (1 in.) at the both sides of the unit.

n WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

n AND ....

• The unit is designed to function as soon as power is supplied,

however, a warm up for 10 minutes is required for satisfying

complete performance described in the data sheet.

BARGRAPH INDICATOR

MODEL

48V

INSTRUCTION MANUAL

Bezel

Nameplate

Retaining Clip

48V

P. 2 / 4

EM-9311 Rev.5

COMPONENT IDENTIFICATION

n FRONT PANEL CONFIGURATIONS

Nameplate

Acrylic Cover

Scale Plate

Ventilation Slits

at the Top and Bottom

(15 cm min.)

Span Adj.

Zero Adj.

50 40 30 20 1001020304050

°C

Tag No.

Label

■ VERTICAL MOUNTING

50 40 30 20 10 01020304050

Input 1

Input 2

• Single

■ HORIZONTAL MOUNTING

• Single

• Dual

–––

–

°C

–

Tag No.

Label

*Engineering units longer than 3 characters are indicated here.

Remark: If there is only one engineering unit with dual bargraph type,

the position and maximum number of characters for single bargraph

type are applied.

48V

P. 3 / 4

EM-9311 Rev.5

INSTALLATION mm (inch)

n EXTERNAL DIMENSIONS

n PANEL CUTOUT

TERMINAL CONNECTIONS

Refer to the connection diagrams below.

144 (5.67)

BEZEL

36 (1.42)

41 (1.61)

135 (5.31)

164 (6.46)

9 (.35) 20 (.79)

139 (5.47)

36 (1.42)

7.5 (.30)

138.1 (5.44)

144 (5.67)

9.4 (.37)

M3 (.12) SCREW BEZEL

139.5

–0

139.5

–0

164 min.

Note 1. A bezel is required between units for high-density

mounting.

Note 2. Observe at the minimum of 5 cm above

and below the units for heat dissipation.

Note 1. A bezel is required between units for high-density

mounting.

L = (38 x n)

(n: number of units)

L = 38 x (n–1) + 36.5

(n: number of units)

–0

■ VERTICAL MOUNTING ■ HORIZONTAL MOUNTING

Panel thickness: 1.6 – 5.5 mmPanel thickness: 1.6 – 5.5 mm

139.5

–0

INPUT

–

DC POWER

–

AC POWER

■ 48V-1

INPUT 1

–

INPUT 2

–

DC POWER

–

AC POWER

■ 48V-2

48V

P. 4 / 4

EM-9311 Rev.5

CALIBRATION PROCEDURE

This unit is calibrated at the factory to meet the ordered speci-

ﬁcations, therefore you usually do not need any calibration.

For matching the indication to a receiving instrument or in

case of regular calibration, adjust the output as explained

in the following.

n HOW TO CALIBRATE THE OUTPUT INDICATION

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output indication to

0%.

2) SPAN: Apply 100% input and adjust output indication to

100%.

3) Check ZERO adjustment again with 0% input.

When ZERO value is changed, repeat the above procedure 1) – 3).

MAINTENANCE

Regular checking procedure is explained below:

n CHECKING

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

indication for the respective input signal remains within

accuracy described in the data sheet. When the output is out

of tolerance, recalibrate the unit according to the "CALIBRA-

TION PROCEDURE" explained earlier.

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive

remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this

warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original

sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: info@m-system.co.jp

M-system 48V User manual

M-system 48V User manual

Related papers

Other documents