Frigidaire FFTA1033U2 Owner's manual
- Category
- Mobile air conditioners
- Type
- Owner's manual
This manual is also suitable for
TABLE OF CONTENTS
www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352
All about the
Use & Care
Care and Cleaning
.............................................. 11
Energy Saving Ideas ........................................... 11
66129927393 (June 2009)
Product Registration 4
Normal Sounds .................................................... 4
.............................................
5 serutaeF renoitidnoC riA .......................................
Important Safety Instructions ............................... 2-3
01-5snoitcurtsnI gnitarepO .........................................
of your
Room Air Conditioner
Before You Call................................................... 12
Major Appliance Limited Warranty........................ 13
Important Safety Instructions
WARNING
For Your Safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance. Read product labels for flammability and other warnings.
WARNING
Prevent Accidents
To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner,
follow basic precautions, including the following:
Be sure the electrical service is adequate for the model you have chosen. This information
can be found on the serial plate, which is located on the side of the cabinet and behind the
grille.
If the air conditioner is to be installed in a window, you will probably want to clean both
sides of the glass first. If the window is a triple-track type with a screen panel included,
remove the screen completely before installation.
Be sure the air conditioner has been securely and correctly installed according to the
separate installation instructions provided with this manual. Save this manual and the
installation instructions for possible future use in removing or reinstalling this unit.
When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front
and rear coils.
The complete electrical rating of your new room air conditioner is stated on the serial plate.
Refer to the rating when checking the electrical requirements.
Be sure the air conditioner is properly grounded. To minimize shock and fire hazards,
proper grounding is important. The power cord is equipped with a three-prong grounding
plug for protection against shock hazards.
Your air conditioner must be used in a properly grounded wall receptacle. If the wall
receptacle you intend to use is not adequately grounded or protected by a time delay fuse
or circuit breaker, have a qualified electrician install the proper receptacle.
Do not run air conditioner without outside protective cover in place. This could result in
mechanical damage within the air conditioner.
Do not use an extension cord or an adapter plug.
WARNING
Electrical Information
WARNING
Avoid fire hazard or electric shock. Do not
use an extension cord or an adaptor plug. Do
not remove any prong from the power cord.
NOTE:
The power supply cord with
this air conditioner contains a current
detection device designed to reduce the risk
of fire.
Please refer to the section ‘Operation of
Current Device’ for details.
In the event that the power supply cord is
damaged, it cannot be repaired. It must be
replaced with a cord from the product
manufacturer.
2
2009 Electrolux Home Products, Inc. All rights reserved.
NOTE:
This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as
instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that
may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.
SAFETY PRECAUTIONS
This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.
Do not insert or place fingers or objects into the air discharge area in the front of the unit.
Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.
Do not cut or damage the power cord.
If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.
In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized
Electrolux servicer.
Do not operate the air conditioner with wet hands.
Do not pull on the power cord.
Do not drink any water that is drained from the air conditioner.
DANGER! Avoid Serious Injury or Death
115V
15A
230V
15A
230V
20A
230V
30A
Do not, under any
circumstances, cut,
remove or bypass the
grounding prong.
Grounding Prong
Important Safety Instructions
3
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.
Unit must be upright for one hour prior to operating.
Plug in &
press RESET
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
Plug in the Air Conditioner.
The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
notice a click as the RESET button pops out.
Press the RESET button. Again you will notice a click as the button engages.
The power supply cord is now supplying electricity to the unit. (On some products this is also
indicated by a light on the plug head).
NOTE:
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.
If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained
from the product manufacturer.
SAFETY PRECAUTIONS
Provide ventilation per installation instructions.
Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make units run excessively.
Do not climb on or place objects on outdoor part of the unit.
Do not hang objects off the unit.
Do not place containers with liquids on the unit.
Turn off the air conditioner at the power source when it will not be used for an extended period of time.
Periodically check the condition of the unit’s installation accessories for any damage.
Do not apply heavy pressure to the radiator fins of the unit.
Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.
Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.
Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp metal edges.
Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading to possible electric shock.
When cleaning the unit, first make sure that the power and circuit breaker are turned off.
CAUTION! Avoid Injury or damage to the unit or other property
Record Your Model and Serial Numbers
Record in the space provided below the model and serial numbers. On all models, the
serial plate is located on the outside of the cabinet.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company.
Normal Sounds
Today’s high efficiency compressors
may have a high pitched chatter
during the cooling cycle.
High pitched Chatter
Unit may vibrate and make noise
because of poor wall or window
construction or incorrect installation.
Vibration
Sound of Rushing Air
At the front of the unit, you may
hear the sound of rushing air
being moved by the fan.
Gurgle/Hiss
“Gurgling or hissing” noise may be heard
due to refrigerant passing through
evaporator during normal operation.
Product Registration
Product Registration & Normal Sounds
4
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
Pinging or Swishing
Droplets of water hitting condenser
during normal operation may cause
“pinging or swishing” sounds.
Note: Don’t try to drill any holes
on the base pan to eliminate the
normal sounds, otherwise it will
void the warranty.
5
Before you begin, thoroughly familiarize yourself with the control panel and remote
as shown below and all its functions, then follow the symbol for the functions you
desire. The unit can be controlled by the touch pad alone or with the remote.
ELECTRONIC CONTROL
Air Conditioner Features
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
Operating Instructions
NOTE
The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.
:EES LLIW UOY:NO TINU NRUT OT
PRESS ON/OFF BUTTON
DO THIS:
Air Conditioner Features & Operating Instructions
Battery Size: AAA
Warning: Do not mix old and new batteries. Do not mix alkaline,
standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
NOTE: The unit will run in energy saver(eco) mode
when powered on each time, if last shutdown is in cool
or energy saver(eco) mode. In this mode, the fan will
continue to run for 3 minutes after the compressor shuts off.
The fan then cycles on for 90 seconds at 10 minute intervals
until the room temperature is above the set temperature, at
which time the compressor turns back on.
ADJUSTS
TEMPERATURE
OR TIME
DISPLAYS
TEMPERATURE/TIME
SETS FAN
SPEED
SETS MODE
TURNS UNIT
ON OR OFF
ACTIVATES
TIMER
CHECK FILTER
RESET BUTTON
SLEEP MODE
REMOTE TEMP
SENSING INDICATOR
(some models)
FOR HEAT MODELS
w/DISPLAY &
REMOTE SENSING
BUTTON
6
Operating Instructions
TO CHANGE TEMPERATURE SETTlNG:
:EES LLIW UOY:SDEEPS NAF TSUJDA OT
Note: This function is deactivated in the heating mode on
115V models.
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
YOU WILL SEE:
PRESS TO RAISE
PRESS TO LOWER
DO THIS:
Note: Tap or hold either up ( ) or down ( ) button until the
desired temperature is seen on the display. This temperature
will be automatically maintained anywhere between 60 °F
(16 °C) and 90 °F (32 °C) for cooling mode. The temperature
will be automatically maintained anywhere between 55 °F
(13 °C) and 80 °F (27 °C) for heating mode. If you want the
display to read the actual room temperature. See "To Operate
on Fan Only" section on Page 7.
TO USE AUTO FAN FEATURE:
PRESS FAN BUTTON,
CHOOSE AUTO
DO THIS:
YOU WILL SEE:
DO THIS:
Operating Instructions
(continued)
PRESS FAN SPEED
TO SELECT
Note: During auto fan speed, the unit will control the fan speed
automatically. In cool/eco mode, fan starts at Low Speed and
adjusts to a higher speeds when the room temperature
increase. In heat mode, fan starts at Low Speed and adjusts
to a higher speeds when the room temperature decrease.
7
Operating Instructions
Operating Instructions
(continued)
:EES LLIW UOY:YLNO NAF NO ETAREPO OT
COOL FEATURE:
YOU WILL SEE:
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
DO THIS:
PRESS
MODE BUTTON
CHOOSE
FAN ONLY
CHOOSE COOL
SLEEP FEATURE:
DO THIS:
PRESS
SLEEP BUTTON
YOU WILL SEE:
Note: Use this function only when cooling is not desired, such
as for room air circulation or to exhaust stale air on some
models. You can choose any fan speed you prefer. (Except
“Auto Fan”). During this function, the display will show the
actual room temperature, not the set temperature as in the
cooling mode. Fan Only cannot be selected when the unit is
in the “Remote Sensing” mode. (on those units with that
feature).
DO THIS:
PRESS
MODE BUTTON
Note: In this mode, the fan remains on all the time.
In Cool/Heat mode the selected temperature will increase/
decrease by 2 °F 30 minutes after the mode is selected.
The temperature will then increase/decrease by another 2 °F
after an additional 30 minutes. This new temperature will be
maintained for 7 hours before it returns to the originally selected
temperature. This ends the "Sleep" mode and the unit will
continue to operate as originally programmed. The "Sleep" mode
program can be cancelled at any time during operation by
again pressing the "Sleep", “mode”, “power” button or ( )
and ( ) buttons.
8
Operating Instructions
Operating Instructions
(continued)
CHECK FILTER FEATURE, YOU WILL SEE:
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
DO THIS:
PRESS FILTER
RESET BUTTON
TIMER: DELAY STOP / START FEATURE YOU WILL SEE HOW MUCH TIME IS CHOSEN:
FIRST
DO THIS:
PRESS
TIMER BUTTON
THEN
DO THIS:
PRESS
UP/DOWN BUTTONS
Note: This feature is a reminder to clean the Air Filter (See
Care and Cleaning) for more efficient operation. The LED
(light) will illuminate after 250 hours of fan operation. To reset
after cleaning the filter, press the "Filter Reset" button and
the light will go off.
Note: For Delay Stop, the unit must be in the On position
Note: For Delay Start, the unit must be in the Off position.
First, Press TIMER button, then adjust timer setting, tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay
timer at 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time
remaining until start (8, 7.5, 7, etc.). The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool,
eco, or Fan Only was the last mode selected) . The temperature maintained will be the same as previously set. To change
the set temperature, press "mode" then Up or Down arrows until the desired temperature is indicated on the display. After 5
seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Pressing the
unit timer or on/off button at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the
unit either starts or stops. Once that happens the above steps have to be repeated again.
DO THIS:
PRESS MODE
BUTTON
SELECT HEAT
HEATING FEATURE(on some models) YOU WILL SEE:
Note: This feature can be used with any combination of FAN
Speeds (Low speed only on 115V models), Timer, or Sleep Modes.
When in the "Heat" mode,the fan will run continuously while heat
is needed. The temperature will automatically be maintained
anywhere between 55 °F(13 °C) and 80 °F(27 °C). When the
room set temperature is satisfied, the fan will cycle off and on
to circulate and sample the room air.
9
Operating Instructions
Operating Instructions
(continued)
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
TO CHANGE TEMPERATURE UNIT DISPLAY:
DO THIS:
PRESS AND HOLD THE
UP/DOWN BUTTONS
TOGETHER FOR 3 SECONDS
Note: The control is capable of displaying temperature in
degrees Fahrenheit or degrees Celsius.
YOU WILL SEE:
REMOTE SENSING FEATURE
(on some models)
LIGHT pulsing ( On & Off intermittently ).
DO THIS:
PRESS REMOTE
SENSING BUTTON
NOTE: Remote display
is actual temperature
at remote control only
NOTE: Unit display shows the set temperature
If the display reads "AS", a sensor has failed. Contact your
Authorized Frigidaire Service Center.
FAULT CODES:
If the display reads "ES", a sensor has failed. Contact your
Authorized Frigidaire Service Center.
If the display reads "HS", a sensor has failed. Contact your
Authorized Frigidaire Service Center.
Note: This feature can be activated from the remote control ONLY, the unit must be in cool/eco mode.
To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing button. Next, use
the “ ” buttons to set the desired temperature at the remote. (Note that the set temperature will only be displayed on the unit
itself ). The signal icon on the remote control will pulse each time it sends a signal. lt will periodically send this signal until the feature
is deactivated by pressing the remote sensing button. lf the unit does not receive the remote sensing signal during a maximum of 200
seconds interval, the unit will end remote sensing mode automatically.
The display on the remote control indicates the temperat
ure at the remote ONLY.
NOTE: The Remote Sensing function is terminated either by using the Remote Sensing button or the main ON/OFF button on the unit.
10
Operating Instructions
Operating Instructions
(continued)
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
ADDITIONAL THINGS YOU SHOULD KNOW
Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.
The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly.
This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue
to run during this time.
The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees (in cool mode), 55F
and 80F degrees (in heat mode).
There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY/HEAT. This is to cover the possibility of
having to roll through to select another mode.
After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.
:EES LLIW UOY:FFO TINU NRUT OT
DO THIS:
PRESS
ON/OFF BUTTON
(6-WAY)
Air Directional Louvers
Air directional louvers control air flow direction. Your air conditioner has the louver
type described below.
Slider Type
The louvers will allow you to direct the air flow Up or Down and Left or Right
throughout the room as needed. Drag the adjuster tablet until the desired
Left/Right direction is obtained. Pivot horizontal louvers until the desired
Up/Down direction is obtained.
ADJUSTER TABLET
Note: If the unit is turned off in heat mode (if applicable) or
fan only mode, it will return to the same setting when it is
turned on again. When the unit is turned off in cool or energy
saver(eco) mode, it will run in energy saver(eco) mode
when it is turned on again, but the setting of temperature
and fan speed will remain.
Care and Cleaning & Energy Saving Ideas
11
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
Energy Saving Ideas
Do not block air flow inside with blinds, curtains or furniture; or outside with
shrubs, enclosures, or other buildings.
The capacity of the room air conditioner must fit the room size for efficient and
satisfactory operation.
Install the room air conditioner on the shady side of your home. A window that faces
north is best because it is shaded most of the day.
Close the fireplace damper, floor and wall registers so cool air does not escape up
the chimney and into the duct work.
Keep blinds and drapes in other windows closed during the sunniest part of the day.
Clean the air filter as recommended in the section “Care and Cleaning”.
Proper insulation and weather stripping in your home will help keep warm air out
and cool air in.
External house shading with trees, plants or awnings will help reduce the air
conditioner’s work load.
Operate heat producing appliances such as ranges, washers, dryers and dishwashers
during the coolest part of the day.
Care and Cleaning
Clean your air conditioner occasionally to keep it looking new. Be sure to unplug
the unit before cleaning to prevent shock or fire hazards.
Air Filter Cleaning
The air filter should be checked at least once a month to see if cleaning is
necessary. Trapped particles in the filter can build up and cause an accumulation
of frost on the cooling coils.
Grasp the filter by the center and pull up and out.
Wash the filter using liquid dishwashing detergent and warm water. Rinse filter
thoroughly. Gently shake excess water from the filter. Be sure filter is
thoroughly dry before replacing
Or instead of washing, you may vacuum the filter clean.
Cabinet Cleaning
Be sure to unplug the air conditioner to prevent shock or fire hazard. The
cabinet and front may be dusted with an oil-free cloth or washed with a cloth
dampened in a solution of warm water and mild liquid dishwashing detergent.
Rinse thoroughly and wipe dry.
Never use harsh cleaners, wax or polish on the cabinet front.
Be sure to wring excess water from the cloth before wiping around the controls.
Excess water in or around the controls may cause damage to the air conditioner.
Plug in air conditioner.
Winter Storage
If you plan to store the air conditioner during the winter, remove it carefully from
the window according to the installation instructions. Cover it with plastic or return
it to the original carton.
NOTE: To prevent rust or electrical connections from being damaged, store air
conditioner in an upright position and a dry place.
OCCURRENCE SOLUTION
Wall plug disconnected. Push plug firmly into wall outlet.
Plug Current Device Tripped. Press the RESET button.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.
Control is OFF. Turn Control ON and set to desired setting.
Air conditioner will not operate.
Air conditioner cooling, but room
is too warm - NO ice forming on
cooling coil behind decorative
front.
Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.
Temperature is set too high. Set temperature to a lower setting.
Air directional louvers positioned improperly. Position louvers for better air distribution.
Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in
front of unit.
Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.
Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling,
floor and furniture.
Air conditioner turns on and off
rapidly.
Dirty air filter - air restricted. Clean air filter.
Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils
more frequently.
Before You Call
Air conditioner cooling, but room
is too warm - ice forming
on cooling coil behind decorative
front
Outdoor temperature below 60 F (16 C). To defrost the coil, set FAN ONLY mode.
OO
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY
mode.
Temperature is set too low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then,
set temperature to a higher setting.
12
Room temperature below 60°F (16°C). Cooling may not occur until room temperature rises above
60°F (16°C).
Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil.
Air from unit does not feel cold
enough.
Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to
restart when set in the COOL mode.
Reset to a lower temperature.
Noise when unit is cooling.
Air movement sound. This is normal. If too loud, set to lower FAN setting.
.devreser sthgir llA.cnI ,stcudorP emoH xulortcelE 9002
Water dripping INSIDE when
unit is cooling.
Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to
installation instructions or check with installer.
Water dripping OUTSIDE when
unit is cooling.
Unit removing large quantity of moisture from humid room. This is normal during excessively humid
days.
Window vibration - poor installation. Refer to installation instructions or check with installer.
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not
the result of defective workmanship or materials in this appliance.
If These Solutions Fail, Call 1-800-944-9044(US)/1-800-265-8352(Canada)
For Frigidaire Service.
Remote Sensing Deactivating
Prematurely (some models).
Remote control not located within range. Place remote control within 20 feet & 120° radius of the
front of the unit
Room too cold.
Set temperature too low. lncrease set temperature.
Remote control signal obstructed. Remove obstruction.
Remote Sensing activated (on some models) and remote control located in Hot Spot - Relocate remote
control or deactivate remote sensing.
Major Appliance Limited Warranty
13
Exclusions
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
This warranty does not cover the following:
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not
in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,
handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external
causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
If You Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described
or illustrated are subject to change without notice.
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
USA
1.800.944.9044
Frigidaire
10200 David Taylor Drive
Charlotte, NC 28262
Your appliance is covered by a limited five (5) year warranty. For five (5) years from your original date of purchase, Electrolux
will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship
when such appliance is installed, used and maintained in accordance with the provided instructions.
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME
STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO FIVE YEARS OR THE SHORTEST
PERIOD ALLOWED BY LAW, BUT NOT LESS THAN FIVE YEARS. ELECTROLUX SHALL NOT BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
Frigidaire FFTA1033U2 Owner's manual
- Category
- Mobile air conditioners
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI