Troybilt 20210 Owner's manual

Brand: Troybilt

Model: 20210

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

020210

,®

/ Ma d

Pressure Washer / Lavadora de Presi6n

Modem / Modemo 0202J0

iMPORT.ANT: RE.AD SAFETY RULES.AND iNSTRUCTiONS C.AREFULLY

IMPORT.ANTE: LEYO LA SEGURJDAD LAS ORDENESY LAS JNSTRUCCJONES DETENJDAMENTE

Questions? Preguntas?

- J-888-6J J-6708 PloF 8-5 CT

TroyoBilt@ is a registered trademark ofTroyoBilt, LLC and is used under license to Briggs & Stratton Power Products.

TroyoBilt® es una marca registrada de TroyoBilt, LLC y se usa abajo licencia a Briggs & Stratton Power Products.

8RJGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON,WiSCONSiN, U.S.A.

Printed in USA

Manual No. 193776GS Revision 3 (05/20/2004)

Safety Rules

TABLE OF CONTENTS

Safety RuHes.................................... 2-4

Know Your Pressure _A/asher ........................ 5

AssembHy ...................................... 6-8

Operation .................................... 9- HH

Maintenance ................................. H2-H4

Storage ........................................ H5

Notes ......................................... H6

TroubHeshoodng ................................. H7

Rephcement Parts ............................ H8= H9

Warranty ................................. Last Page

EQUmPNENT

Readthismao°a,oare .,yandbecome

..... familiar with your pressure washer. Know the

appmications, the mimitations and any hazards

invomved.

This manuaHcontains information for a high pressure

washer that operates at 3,700 PSI at a flow rate of

4.0 gallons per minute.This powerful high quality system

features hrge H2" wheeHs, a pump equipped with an

automatic cooH down system, chemicaH iniecdon system,

nozzle extension with quick connect nozzles, safety goggles,

heavy duty 50' hose, and more.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve the

right to change, alter or otherwise improve the product and

this document at any time without prior notice.

SAFETY RULES

This is the safety alert symbol, it is used to

alert you to potential personal injury

hazards° Obey aH safety messages that follow

this symbom to avoid possibme injury or death.

The safety alert symbol (_) is used with a signal word

(DANGER, CAUTION,_WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGEP_ indicates

a hazard which, if not avoided, will result in death or serious

iniury. WARNING indicates a hazard which, if not

avoided, could result in death or serious iniury. CAUTION

indicates a hazard which, if not avoided, might result in

minor or moderate iniury. CAUTION, when used

without the alert symbol, indicates a situation that could

result in equipment damage. Follow safety messages to

avoid or reduce the risk of iniury or death.

[

Hazard Symbols and Meanings

Toxic Fumes Electrical Shock

Z d

Slipper 7 Surface Fall Fluid Iniection

Fire Explosion Hot Surface

Moving Parts Flying Obiects Kickback

Section 1: Safety Rules

DANGER

Operate pressure washer ONLY outdoors,

Use a respirator or mask whenever there is a chance that

vapors may be inhaled.

Read all instructions with mask so you are certain the mask will

provide the necessary protection against inhaling harmful vapors.

WARNING 1

. Keep water spray away from electric wiring or fatal electric

shock may resuk.

WARNING

Keep spray tip between 8 to 24 inches away from cleaning

surface.

Operate this unit on a stable surface.

The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fall due to slippery surfaces.

Be extremely careful if you must use the pressure washer from

a ladder, scaffolding or any other relatively unstable location,

Firmly grasp spray gun with both hands when using high

pressure spray to avoid iniury if gun kicks back.

WARNING

WHEN ADDING FUEL

Turn pressure washer" OFF and let it cool at least 2 minutes

before removing gas cap.

Fill fuel tank outdoors.

DO NOT overfill tank.Allow space for fuel expansion.

Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

DO NOT light a cigarette or smoke.

VHEN OPERATING EQUIPMENT

• Transport/repair with fue! tank EMPTY or with fue! shutoff

valve OFE

WHEN STORING FUEL OR EQUIPMENT WiTH FUEL

iN TANK

Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have a pilot light or" other

ignition source because they can ignite fue! vapors.

WARNING

NEVER aim spray gun at people, animals or plants,

DO NOT allow CHILDREN to operate pressure washer.

NEVER repair high-pressure hose. Replace it with an

equivalent rated hose.

Keep high pressure hose connected to pump and spray gun

while system is pressurized.

Section 1: Safety RuJes

WARNING

DO NOT touch hot surfaces,

Stay dear of exhaust gases.

Allow equipment to cod before touching,

WARNING 1

, DO NOT wear loose clothing, iewetry or anything that may

be caught in the starter or other rotating parts.

, Tie up long hair and remove jeweJr_,_

WARNING 1

, Always wear eye protection when using this equipment or in

vicinity of where equipment is in use.

J wAR.I.G 1

WHEN ADJUSTING OR MAKING REPAiRSTOYOUR

PRESSURE WASHER

Disconnect spark pJugwire from spark pJugand placewire

where itcannot con_ct sparkplug.

CAUTION

DO NOT tamper with governed speed.

DO NOT operate pressure washer above rated pressure.

CAUTION

DO NOT secure spray gun in open position,

DO NOT leave spray gun unattended while machine is

running.

NEVER use a spray gun which does not have a trifler lock or

trigger guard in place and in working order:

Always be certain spray gum nozzles and accessories are

correctly attached.

DO NOT point spray gun at glass when in jet spray mode.

NEVER aim spray gun at plants.

If you have questions about intended use_ask dealer or

contact Brigs & Str_tton Power Products_

NEVER operate units with broken or missing parts, or

without protective housing or covers.

DO NOT by-pass any safety device on this machine.

Before starting pressure washer in cold weather, check all

parts of the equipment to be sure ice has not formed there.

NEVER move machine by pulling on high pressure hose. Use

handle provided on unit.

Check fuel system for leaks or signs of deterioration, such as

chafed or spongy hose, loose or missing clamps, or damaged

tank or cap. Correct all defects before operating pressure

washerL

This equipment is designed to be used with Briggs & Stratton

Power Products authorized parts ONLY. If equipment is used

with parts that DO NOT comply with minimum specifications,

user assumes all risks and liabilides_

Features and Controls

KNOWYOUR PRESSURE WASHER

Read this owner's manual and safety rules before operating your pressure washer,

Compare the ilhstrations with your pressure washer to familiarize yourself with the Iocaqons of various controls and

adjustments. Save ths manual for future reference.

Nozzle Extension with

Quick Connect

Spray Gun

Throttle Lever

Choke Lever

_:JR FuelValve

ecoil Starter

% Run/Stop Switch

(on front of engine)

Air Filter

High Pressure Hose

Pump equipped with

Automatic Cool Down System

Chemical Injection Siphon/Filter

Air lsi[ter -- Protects engine by filtering dust and debris out

of intake ain

Automatic Coo[ Down System -- Cycles water through

pump when water reaches [25 °=[55°EWarm water will

discharge from pump onto ground.This system prevents

internal pump damage.

Chemical injection Siphon/Filter -- Used to siphon

detergent or other pressure washer chemicals into the low

pressure stream,

Choke Lever -- Prepares a cold engine for starting.

Fuel Tank- Fill tank with recommended fuel.

High Pressure Hose -- Connect one end to the water

pump and the other end to the spray gun.

High Pressure Outlet with Quick Connect--To connect

high pressure hose.

Pressure

Control Knob

High Pressure Outlet

with Quick Connect

VVater Inlet

Nozzle Extension with Quick Connect -- Permits easy

switching between five different spray tips_

Oil Fill Cap -- Fiil engine with oil here.

Pressure Control Knob --Varies pressure of high pressure

spray.

Pump -- Develops high pressure.

[Recoil Starter -- Use for starting the engine manually.

Run/Stop Switch -- Set this switch to "Run" before using

recoil starter. Set switch to "Stop" to switch off engine.

Spray Gun -- Controls the application of water onto

cleaning surface with triter device. Includes safety latch.

Quick Connect Spray Tips -- Chemical iniecdon, 0 °, [5 °,

25 °, and 40°: for various cleaning applications.

Throttle Lever--Sets engine in starting mode for recoil

starter.

Water Inlet -- Connect garden hose here.

ASSEMBLY

mMPORTANT: Read entireowner'smanuaH beforeyou

attempt to assembHeor operate your new pressure washen

Remove Pressure 4asher From

Remove high pressure hose_ handHe_and parts box

incHuded with pressure washer.

SHicetwo corners at end of carton from top to bottom

so paneHcan be folded down fiat, then remove aHH

pacHdngmaterial

RoHHpressurewasher out of carton.

Carton Contents

[terns in the carton include:

Main unit

High pressure hose

Spray gun with qock connect fitthlg

Nozzle extension with qock connect fitting

HandHe

Engine oil

Safety goggles

Parts Bag OncHudesthe foHHowing):

Owner's registration card

Bag containing 5 muHti-coHored quick connect

spray tips

Owner's manual

Engine manual

Engine warranty card

Emissions control warranty card

Handle Fastening Hardware Kit (which includes):

Carriage Bolts (2)

PHasticKnobs (2)

ff any of the above parts are missing or damaged_caHHthe

pressure washer heHpHineat i =888=6 i i =6708.

PREPARING PRESSURE

WASHER FOR USE

If you have any probHems with the assembHy of your

pressure washer or if parts are missing or damage& caHHthe

pressure washer heHpHineat i -888-6 i i -6708.

To prepare your pressure washer for operation, you

wii[ need to perform these tasks:

I. Fill out and send in registration card.

2. Verify oil dipsticl< has been installed into pump (Figure I).

3. Attach handle to main unit.

4. Add oiHto engine.

5. Add fuel to fuel tank.

6. Connect high pressure hose to spray gun and pump.

7. Connect water supply to pump.

8. Connect nozzHeextension to spray gun.

9. SeHectand instaHHdesired quick connect spray tip.

Section 3: Assembly

Attach Handle

H. PHace handHe assembHy onto handHe supports connected

to main unit. Hake sure holies in handHe aHign with holies

on handHe supports (Figure 2).

HandHe

[[ Supports[

NOTE: It may be necessary to move the handHesupports

from side to side in order to aHignthe handHe so it wiHHsHide

over the handHe supports.

2. Insert carriage boHts through holies from outside of unit

and attach pHastic knob on inside of handHes (Figure 3).

Tighten by hand.

i i

3. Insert muHti-coHored spray tips in spaces provided in

handHe.

Add Engine Oil and Fuel

° PHace pressure washer on a HeveHsurface.

• Refer to engine manual for oil and fuel fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty,

o Refer to engine owner's manual and follow oil and fuel

recommendations and instructions.

NOTE: Check oiHoften during engine break-in. Refer to

engine owner's manual for recommendations.

Connect Hose and Water Supply to

IMPORTANT:To avoid pump damage,you must assembHe

the nozzle extension to the spray gun and attach all hoses

before you start the engine.

H. UncoiH high pressure hose and attach quick connect

end of hose to base of spray gun (Figure 4). PuHHdown

on coHHar of quick connect, sHide onto spray gun and Het

go of coHHar.Tug on hose to be sure of tight connection.

Connect high

pressure hose

here.

NOTE: Remove and discard aHHpump shipping caps before

attaching hoses.

Section 3: Assemb(y

Similarly, attach other end of high pressure hose to

high pressure oudet on pump (Figure 5). PuHHdown on

coHHarof quick connect_ sHideonto pump and Hetgo of

coHHar,PuHHon hose to be sure of tight connection.

Connect high

pressure hose here

Before connecting garden hose to water inHet_inspect

inHetscreen (Figure 6).

CHeanscreen if it contains debris, repHaceif damaged.

DO NOT RUN PRESSUREWASHER IF SCREENIS

DAHAGED,

;_/_7 _ DO NOT use if

_amaged, dean if

dirty.

4. Run water through garden hose for 30 seconds to

dean out any debris.Turn off water.

[MPORTANT: DO NOT siphon standing water for the

water supply, Use ONLY coHdwater (less than [00°F).

5. Connect garden hose (not to exceed 50 feet in length)

to water inHet.Tighten by hand (Figure 6).

Damageto equipment resulting from failure to follow this

instruction will void warranty,

6, Turn ON water and squeeze trigger on spray gun to

purge pump system of air and impurities,

WANNING

Always wear eye protection when using this equipment or in

vicinity of where equipment is in use.

Before starting the pressure washer, be sure you are wearing

adequate eye protection,

Checklist Be[ore Start[n Eg Eng[ne

Review the unit's assembHyto confirm you have performed

aHHof the following:

H. Hake sure handHe is in pHaceand secure.

2. Check that oi[ has been added to proper [eve[ in

engine crankcase.

3. Add proper fuel to fuel tank.

4. Check for properHy attached hose connections.

5. Check to make sure there are no kinks, cuts, or

damage to high pressure hose.

6. Provide a proper water suppHy (not to exceed H00°F)

at an adequate flow.

7. Be sure to read "Safety RuHes"and "HowTo Use

PressureVVasher" before using pressure washer.

Operation

HOWTO USE PRESSURE

If you have any probHems operating your pressure washer,

pHeasecaHHthe pressure washer heHpHineat 1-888-61 1-6708.

How to Start Engine

The best way to start your pressure washer for the first

time is to follow these instructions step-by-step.Ths

starting information aHsoappHiesif you have Hetthe unit sit

idHefor at Heasta day.

H. PHacepressure washer near an outside water source

capabHeof suppHyingwater at a flow rate greater than

5.0 gaHHonsper minute and no Hessthan 20 PSI at

pressure washer end of garden hose.

2. Hake sure unit is in a HeveHposition.

3. Check that high pressure hose is connected to spray

gun and pump. See "Preparing Pressure _A/asher for

Use" for iHHustrations.

Connect garden hose to water inlet on pressure

washer pump. Turn ON water.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

5. Squeeze trigger on gun untiH you have a steady stream

of water.This purges pump of air and impurities.

6. Attach nozzHe extension to spray gun (Figure 7).

Tighten by hand.

7. Choose spray tip you want to use and insert it into

nozzHe extension. See "How to Use SprayTips'.

8. AppHy safety Hatch to spray gun trigger (Figure 8).

Safety Latch

Start engine according to instructions given in engine

owner's manuaH.AHso see operating instructions tag

Hocated on the pressure washer.

CAUTION

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback,

• [f engine starts and fails to continue to run or if increased

resistance is felt during starting pull attempts, squeeze trigger

on spr D, gun.

NOTE: AHways keep the throttle Hever in the "Fast"

position when operating the pressure washer.

How to Stop Pressure Washer

* Turn engine off according to instructions given in engine

owner's manua[.

* Squeeze trigger on the spray gun to remieve

pressure in the hose.

NOTE: A smaHHamount of water wiHHsquirt out when you

release the pressure.

Section 4: Opecat[on

I-tow to Use the SprayT[ps

The quick-connect on the nozzHe extension aHHowsyou to

switch between five different spray tips.The spray tips vary

the spray pattern as shown bellow (Figure 9).

CAUTION

* NEVER exchange spr D, tips without locking the safety latch

on the trigger:

FoJJow these instructions to change spray tips:

H. Engage safety Hatchon spray gun.

2. PuHHbacH<coHHaron qock-connect and puHHcurrent

spray tip off. Store spray tips in space provided on

handle storage pane[.

3. SeHect desired spray tip:

For gentle rinse, seHect white 40 ° or green 25 °

spray tip.

To scour surface_ select yellow [5° or red 0° spray

tip.

To appHy chemical seHect bHack spray tip.

4. PuHHbacH<on collar, insert new spray tip and reHease

coHHar.Tugon spray tip to make sure it is secureHy in

pHace.

5. For most effective cHeaning, keep spray tip from 8 to 24

inches away from cHeaning surface, if you get spray tip

too chose, you may damage cHeaning surface. DO NOT

get c[oser than 6 inches when cHeaning tires.

and Chemical

iMPORTANT: Use soaps designed specifically for

pressure washers. HousehoHd detergents couHd damage

the pump.

• Starting the engine without aJl the hoses connected and

without the water turned ON will damage the pump_

Damage to equipment resuking from failure to follow this

instruction will void warranty.

To apply detergent follow these steps:

H. Review spray tip use.

2. Prepare detergent soHution as required by manufacturer.

3. PHace chemica[ injection siphon/tiNter into detergent

container.

• When inserting the filter" into a detergent solution bottle,

route the tube so as to keep it from inadvertently contacting

the hot muffler:

4. Make sure bHack spray tip is instaHHed.

NOTE: Detergent cannot be appHied with the high

pressure spray tips (White, GreemYeHHow, or Red).

Low Pressure

Use to appHy

chemicaH

BHack White

40 °

i i

Green Yellow

25° HS°

i i

Red

Section 4: Opecation

5. Make sure garden hose is connected to water inHet.

Check that hgh pressure hose is connected to spray

gun and pump; start engine.

6. AppHy detergent to a dry surface, starting at lower

portion of area to be washed and work upward_ using

Hong,even, overlapping strokes. DO NOT aHHow

detergent to dry on (prevents streaHdng).

7. AHHowdetergent to soak in between 3-5 minutes

before washing and rinsing. ReappHyas needed to

prevent surface from drying.

Pressure Washer Rinsing

After you have appmied detergent, scour the surface

and rinse it dean as fommows:

H. AppHy safety Hatchto spray gun.

2. Remove bHackchemicaH spray tip from nozzHe

extension.

3. SeHect and instaHHdesired high pressure spray tip

following instructions in "Now to Use SprayTips".

WARNING

4. Increase (decrease) spray pressure by turning pressure

controH knob cHockwise (countercHockwise) (See

"KnowYour Pressure Washer"). Use Hower pressure to

wash items such as a car or boat. Use higher pressure

to strip paint and degrease driveways.

5. AppHy high pressure spray to smaHHarea and check

surface for damage. If no damage is found, you can

assume it is okay to continue cHeaning.

6. Start at top of area to be rinsed, working down with

same overHapping strokes as you used for cHeaning.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gum

circuHating water in the pump can reach temperatures

above H25°F.The system engages to cooHthe pump by

discharging the warm water onto the ground.

Keep spray nozzle between 8 to 24 inches away from cleaning

surface.

Operate this unit on a stable surface.

Be extremely careful ifyou must use the pressure washer from

a Iadde_; scaffolding or any other relatively unstabIe location.

Firmly graspspray gun with both hands when using high

pressure spray to avoid iniury if gun kicks back.

GENERAL MAmNTENANCE

RECOMMENDATmON$

The pressure washer warranty does not cover items that

have been subjected to operator abuse or negligence.To

receive full value from the warranty, the operator must

maintain the pressure washer as instructed in this manual.

° Some adjustments will need to be made periodically to

properly maintain your pressure washer.

° All maintenance in this manual and the engine owner's

manual should be made at least once each season.

° If equipped with inflatable tires, keep the air pressure at

the value marked on the tire or within 15 and 40 psi.

Before

i. Check

2. Check

3. Check

4. Check

5. Check

6. Check

leaks.

Each Use

engine oil HeveL

water inlet screen for damage.

incline filter for damage.

high pressure hose for leaks.

detergent siphoning tube and filter for damage.

spray gun, nozzle extension, and spray tips for

7. Rinse out garden hose to flush out debris.

PRE$SU RE WASH ER

MAINTENANCE

Check and Clean Inlet Screen

Examine the screen on the water inlet. Clean it if the

screen is dogged or replace it if screen is damaged.

Check High Pressure Hose

The high pressure hose can develop leaks from wear,

kinking, or abuse. Inspect the hose each time before using

it. Check for cuts, leaks, abrasions or bulging of cover,

damage or movement of couplings. If any of these

conditions exist, replace the hose immediately.

WARNING

NEVER repair high pressure hose. Replaceit.

Replacement hose rating NUST exceed maximum pressure

rating of unit.

Check Deter_honin_Tube

Examine the filter on the detergent tube and clean if

clogged.The tube should fit tightly on the barbed fitting.

Examine the tube for leaks or tears. Replace the filter or

tube if either is damaged.

Cleaning Detergent $iphoningTube

If you used the detergent siphoning tube, you must flush it

with clean water before stopping the engine.

I. Place chemical injection siphon/fiker in a bucket full of

clean water.

2. Attach bhck low pressure spray tip.

3. Flush for 1=2 minutes.

4. Shut off engine.

mMPORTANT: Simply shutting OFF engine wiii not

release pressure in the system. When the engine has

shut down, squeeze the trigger on the spray gun to

relieve the pressure [n the hose.

Check Gun and Nozzle Extension

Examine the hose connection to the spraygun and make

sure it is secure.Test the trigger by pressing it and making

sure it springs back into place when you release it. Put the

safety latch in the on position and test the trigger.You

should not be able to pressthe trigger.

Check In-Line Filter

Refer to Figure 10 and service the in=line filter if it

becomes clogged, as follows:

Nozzle Extension

Filter Screen

O=ring

Section 5: Maintenance

I. Detach spray gun and nozzle extension from hgh

pressure hose. Detach nozzle extension from spray gun

and remove o:ring and screen from nozzle extension.

Flush screen_ spray gun_ and adjustable nozzle extension

with clean water to clear debris.

2. Place in4ine filter screen into threaded end of nozzle

extension. Direction does not matter. Push screen in

with eraser end of penal[ until it rests fiat at bottom of

opening.Take care to not bend screen.

3. Place o°ring into recess. Push o-ring snugly against

inoline filter screen.

4. Assemble nozzle extension to spray gun_ as described

earlier in this manual.

Purge Pump of Air and

To remove air from the pump, follow these steps:

I. Set up pressure washer as described in "Preparing

Pressure Washer For Use'L Connect water supply and

turn water on.

2. Pull trigger on spray gun and hol&

3. When water supply is steady and constant_ engage

To remove contaminants from the pump, follow

these steps:

1. Set up pressure washer as described in "Preparing

Pressure Washer For Use". Connect water supply and

turn water on.

2. Start engine according to instructions in "To Start

Pressure Washer".

3. Remove nozzle extension from spray gun.

4. Squeeze trigger on spray gun and hold.

S. When water supply is steady and constant_ engage

safety latch and reattach nozzle extension.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure.The

principal cause of excessive pump pressure is a spray tip

clogged or restricted with foreign materials, such as dirt,

etc.To correct the problem, immediately clean the spray

tips following these instructions:

I. Shut off engine and turn off water supply.

2. Remove spray tip from end of nozzle extension.

3. Remove inoline filter from other end of nozzle

extension.

4. Use a small paper clip to free any foreign material

clogging or restricting spray tip (Figure I I).

5. Using a garden hose, remove additional debris by back

flushing water through nozzle extension (Figure 12).

Back flush between 30 to 60 seconds.

6. Reinstall spray tip and in-line filter into nozzle

extension.

7. Reconnect nozzle extension to spray gun.

8. Reconnect water supply, turn on water, and start

engine.

9. Test pressure washer by operating with each Quick

Connect spray tips.

O-Rin_ Maintenance

Purchase an O-Ring/Maintenance KiL part number

191922GS by contacting the nearest authorized service

center. [t is not included with the pressure washer.This kit

includes replacement o-rings, rubber washer and water

inlet filter. Refer to the instruction sheet provided in the kit

to service your unit's o-rings.

Section 5: Maintenance

ENGmNE MAmNTENANCE 4.

See the engine owner's manuaHfor instructions on how to

property maintain the engine. 5.

[ cAuTlo. I °

CHean area around pump oi[ dipstick. Remove dipstick

and firthpump with recommended oiHto "Full" mark on

dipstick (typically 0.43L or H5 oz.).

install pump oiHdipstick.

Wipe up any spilled oil

* Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

* Thoroughly wash exposed areas with soap and wate_t

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OILTO COLLECTION CENTERS.

Pump Maintenance

Changing Pump oim

Change oil after first 50 hours of operation and then every

2.00 hours or 3 months, whichever occurs first.

NOTE:When changing pump oil, use only high quality

nondetergent 30 weight oil. Use no special additives.

Change pump oil as fommows_"

H. Clean area around brass oil drain plug at bottom of

pump.

2.. Remove oil drain plug. Drain oil completely into an

approved container.

3. VVhen oil has completely drained, install oil drain plug

and tighten firmly.

Data tag information is very important if you need help from

our Customer Service Department or an authorized service

dealer.

° The data tag (Figure H3) is located on the base of the

pressure washer. For future reference, please copy the

model, revision, and serial number of the pressure washer

in the space below.

MODEL L

REV NO [

SERIAL L

PSI [

GPM L

Copy HodeH

_ Number Here

Copy Revision

Here

Copy Serial

Number Here

Storage

PREPAPdNG THE fJNmT

FOP, STORAGE

Water shouHd not remain in the unit for Hongperiods of

time. Sediments or minerals can deposit on pump parts and

"freeze" pump action. If you do not pHanto use the

pressure washer for more than 30 days, follow this

procedure:

H. Rush detergentsiphoningtube by pHadngfiHterintoa

paiHof dean water while running pressure washer in

low pressure mode. Flush for one to two minutes.

2. Shut off engine and let it cool, then remove high

pressure and garden hoses. Disconnect spark plug wire

from spar[<pHug.

3. Empty pump of Hiquids by puHHingengine recoiH handle

about 6 times.This should remove most liquid in pump.

4. Use PumpSaver to prevent corrosion buiHd up and

freezing of pump.

5. Store unit in a dean, dry area.

Protecting the Pump

To protect the pump from damage caused by mineral

deposits or freezing, use PumpSaver to treat pump.This

prevents freeze damage and Hubricates pistons and seaHs.

NOTE: PumpSaver is avaiHabHeas an optionaH accessory. It

is not incHuded with the pressure washer. Contact the

nearest authorized service center to purchase PumpSaver.

To use PumpSaven make sure the pressure washer is

turned off and disconnected from suppHy water. Read and

follow aHHinstructions and warnings given on the PumpSaver

container.

• Failure to do so will permanently damage your pump and

render your unit inoperable.

• Freeze damage is not covered under warranty.

CAUTION

Always wear eye protection when using PumpSaver.

NOTE: PumpSaver wiHHdrip from pump after treatment

and wiHHstain wood and concrete.

NOTE: If PumpSaver is not avaiHabHe,draw RV antifreeze

(non-aHcohoH) into the pump by pouring the soHution into a

3-foot section of garden hose connected to inHetadapter

and puHHingrecoiH handHetwice.

STORING THE ENGINE

See the engine owner's manuaH for instructions on how to

properHy prepare the engine for storage.

Notes

TROUBLESHOOTmNG

Problem

Pump has foRowing problems:

failure to produce pressure,

erratic pressure, chattering, [oss

Of pressure, low water volume.

Detergent fails to mix with spray°

Engine shuts down during

operations

Cause

Low pressure spray tip installed.

2. VVater inHetis Mocked.

3. Inadequate water supply.

4. InHethose is kinHmdor leaking.

5. Clogged inlet hose strainer.

6. VVater supply is over 100°E

7. High pressure hose is blocked or

leaks.

8. Gun leaks.

9. Spray tip is obstructed.

0. Pump is faulty.

Detergent siphoning tube is not

submerged.

2. Chemical filter is clogged or

cradmd.

3. Dirty in=linefilter.

4. High pressure spray tip installed.

Out of gasoline.

2. Low oil level.

Correction

I. Rephce spray tip with high

pressure spray tip.

2. Clear inlet.

3. Provide adequate water flow.

4. Straighten inlet hose, patch leak.

S. Check and clean inlet hose

strainer.

6. Provide cooler water supply.

7. Clear blocks in outlet hose.

8. Replace gun.

9. Clean spray tip.

I0. Contact local service facility.

I. Insert detergent siphoning tube

into detergent.

2. Clean or replace fiker/detergent

3. See "Check In=Line Filter".

4. Replace spray tip with low

pressure spray tip.

[. Fi[[ fuel tan[<.

2. Fill crankcase to proper level.

E×pIoded Views and Parts Lists

EXPLODEDVmEW AND

_900

[tern Part # Description

I B 194424GS BASE

2 BI91942GS HANDLE

3 B4805GS HOSE

4 30809GS GROMMET

5 195294GS KIT, Engine Mounting Hardware

6 192132GS KIT, Pump Mounting Hardware

7 194004GS KIT, Garden Hose Inlet

8 95458GS CONNECT, Quick

9 191265GS EoRING

1O B4847GS KIT, SprayTips

I I 192796GS KIT, Chemical Hose/Fiker

[terns Not Illustrated:

Part # Description

193776GS MANUAL, Owners

194356GS KIT, Decals, Srv

BB3061BGS OIL, Engine

191267RGS AXLE

PARTS LIST- MAIN UNIT

[telln

9OO

Part #

H90779GS

B[ 436BGS

192126GS

B2203GS

192310GS

19441 IGS

195016GS

63281GS

194354GS

NSP

Description

ASSY,Extension

GUN

CARVinyl

KIT, Handle Fastening

KIT,Vibration Mount

KIT,Wheel

VALVE,Thermal

KEY

ASSY,Pump (see page 19)

ENGINE

Section 8: E×pioded Views and Parts Lists

EXPLODED VmEW AND PARTS LmST -- PUMP

_ 0

°00 o

_-c

intern Part # Description

I 116B2126GS OIL SEALSquare

A 193990GS KIT_Valve

B 117B2327GS OIL CAP/DIPSTICK

C 134B2327GS OoRING

D 193991GS KIT, Support Ring & Seals

E 193724GS KIT, Hose Tail

F I53B2126GS UNLOADER_Complete

G 250B2327GS KIT_OoRings, Unloader

NOTE: Item letters A o G are service kits and include all parts shown within the box.

Reglas de Seguddad

TABLA DE CONTENIDOS

Regias De Seguridad ................................ :20-11

Conozca Su H_.quina Lavadora a Presi6n .................. 23

Ensambraie ........................................ 24-26

Fundonamiento .................................... 27-19

Mantenimiento ..................................... 30-32

Aimacenamiento ...................................... 3:)

Di_gnosticos De Averias ................................ 34

Piezas De Recambio ................................ [8-[9

Garantia ............................................ 35

DESCNIPCION DEL EQUIPO

Lea este manuaB de manera cu[dadesa y

....... fami[iar[cese con su [avadora de presi6no Conozca

sus uses, sus [imitaciones y cua[quier pe[igro

relacienado con el mismo.

Este manual contiene informaci6n rderente d Iavador a alta

presi6n que funciona a 3,700 psi, a un promedio de fluio de

4.0 galones per minute. Este sistema profesional de alto poder y

de alta calidad, posee una Ilanta de 12 puJgadas, una bomba

equipada con un sistema de enfriamiento, un sistema de inyecci6n

quimica, una extensi6n de lanzas que se pueden conectar

r@idamente, gafas de seguridad, una manguera de alta resistencia

de 50 pies y much{simo m_%.

Se ha hecho cada esfuerzo posible para asegurarse que la

informaci6n que aparece en este manual es exacta 7 se encuentra

actualizada. Sin embargo, nosotros se reserva el derecho a

cambiar, alterar o de otra manera meiorar, el producto y este

documento en cualquier memento, sin previo aviso.

En el estado de California es obligatorio, seg_in la [ey e[ use de

apagachispas (Secci6n 4442 del C6digo de Recursos Pt_blicos de

California). Otros estados pueden tener [eyes similares. Las leyes

federales se aplican en tierras federales. Si equipa el siJenciador

con un apagachispas, este deber_ set mantenido en buenas

condiciones de traba]o.

[NSTRUCCIONES DE SEGUPdDAD

[_ste es el simbo[o de a[erta de seguridad. Sirve

para advertir a[ usuario de un pos[b[e riesgo para

su integridad fisica. Siga todos los mensa]es de

seguridad que figuren despu_s de este s{mbo[o

para evitar [esiones o [ncluso la muerte.

El simbo[o de alerta de seguridad (_) es usado con una palabra

(PEUGRO, ADVERTENCIA, PRECAUCION), un mensaie per

escrito o una ilustraci6n, para alertarlo acerca de cualquier

situaci6n de peligro que pueda existic PEL[GRO indica un riesgo

el cual, si no se evita, causar6 la muerte o una herida grave.

ADVERTENCIA indica un riesgo el cua[, si no se evita, puede

causar la muerte o una herida grave. PRECAUCi6N indica un

riesgo, el cuai, si no se evita, puede causar heridas menores o

moderadas. PRECAUCi6N, cuando se usa sin el simbo[o de

alerta, indica una sieJaci6n que podria resultar en el daffo del

equipo. Siga los mensa]es de seguridad para evitar o reducir los

riesgos de heridas e inclusive la muerte.

ADVERTENCIA ]

E[ escape de[ motor de este producto contiene

e[ementos quimicos reconocidos en el Estado de

California pot producir c&ncer, defectos de nacimiento u

otros da_os de ripe reproductivoo

Simbolos de Peligro y Significados

Gases T6xicos Descarga EI6ctrica

Superficies Resbalosas Inyeccidn Uquida

Fuego Superficie Caliente

Caer

Explosi6n

Partes en Hovimiento Obietos VoJadores Contragoipe

Page is loading ...

Troybilt 20210 Owner's manual

Brand: Troybilt

Model: 20210

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

020210

Download PDF

report

in other languages

español: Troybilt 20210 El manual del propietario

Troybilt 20210 Owner's manual

This manual is also suitable for

Troybilt 20210 Owner's manual

in other languages

Related papers

Other documents